This patch removes the hard coded assumption that the TX ring uses
hardware FIFO 1. This allows the hardware FIFO 1 to be used for RX and
the next free FIFO for TX.

This gives the opportunity to minimize the number of SPI transfers in
the IRQ handler. The read of the IRQ status register and RX FIFO
status registers can be combined into single SPI transfer. If the RX
ring uses FIFO 1, the overall length of the transfer is smaller than
in the original layout, where the RX FIFO comes after the TX FIFO.

Link: https://lore.kernel.org/all/20220217103826.2299157-2-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The PLL is enabled if the configured clock is less than or equal to 10 times
the max clock frequency.

The device will operate with two different SPI speeds. A slow speed determined
by the clock without the PLL enabled, and a fast speed derived from the
frequency with the PLL enabled.

Link: https://lore.kernel.org/all/20220207131047.282110-16-mkl@pengutronix.de
Link: https://lore.kernel.org/all/20201015124401.2766-3-mas@csselectronics.comCo-developed-by: Magnus Aagaard Sørensen <mas@csselectronics.com>
Signed-off-by: Magnus Aagaard Sørensen <mas@csselectronics.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

If the PLL is needed it must be switched on after chip reset. This
patch adds the required call to mcp251xfd_register().

Link: https://lore.kernel.org/all/20220207131047.282110-15-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch prepares the mcp251xfd_chip_clock_init() function for PLL
support.

If the PLL is needed is must be switched on after chip reset. This
should be done in the mcp251xfd_chip_clock_init() function. Prepare
this function to wait for the OSC and PLL to be ready.

Link: https://lore.kernel.org/all/20220207131047.282110-14-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

can: mcp251xfd: __mcp251xfd_chip_set_mode(): prepare for PLL support: improve error handling and diagnostics

This patch prepares the __mcp251xfd_chip_set_mode() function for PLL
support by adding more error checks and diagnostics.

Link: https://lore.kernel.org/all/20220207131047.282110-13-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch renames mcp251xfd_chip_clock_enable() into mcp251xfd_chip_wake() as
this function actually wakes the chip. Additionally the documentation is
adopted.

Link: https://lore.kernel.org/all/20220207131047.282110-12-mkl@pengutronix.deCo-developed-by: Magnus Aagaard Sørensen <mas@csselectronics.com>
Signed-off-by: Magnus Aagaard Sørensen <mas@csselectronics.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch factors out the timestamp initialization from the clock
initialization.

This is a preparation patch for the PLL support, where clock and
timestamp init must be done separately.

Link: https://lore.kernel.org/all/20220207131047.282110-11-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch changes the order of reading the Mode and Oscillator Ready
bits.

Instead of reading the Mode of the chip directly after reset, first
wait for the oscillator to get ready and the chip to fully start up.
Read the Mode after this.

Link: https://lore.kernel.org/all/20220207131047.282110-10-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The function mcp251xfd_chip_wait_for_osc_ready() polls the Oscillator
Control Register for the oscillator to get ready. By passing the
appropriate parameters (osc_reference and osc_mask) it can also poll
for PLL ready.

This patch adjusts the error message if the Oscillator and/or PLL fail
to get ready.

Link: https://lore.kernel.org/all/20220207131047.282110-9-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The function mcp251xfd_chip_wait_for_osc_ready() polls the Oscillator
Control Register for the oscillator to get ready.

This is the first register the driver reads from. Reading implausible
values (all bits set or unset) can be caused by the chip starting up
after power on, waking up after sleep, or by the chip not being preset
at all. Add check for implausible register content
mcp251xfd_reg_invalid() to the regmap_read_poll_timeout() loop.

In case of a regmap_read_poll_timeout() returns a fatal error (and not
a timeout), forward it to the caller.

As mcp251xfd_chip_wait_for_osc_ready() will be called after the probe
function has finished, (currently during ifup), move error message
about failed chip detection from there into the probe function.

Link: https://lore.kernel.org/all/20220207131047.282110-8-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch factors out mcp251xfd_chip_wait_for_osc_ready() into a
separate function, it will be used in several places in the next
patches.

Link: https://lore.kernel.org/all/20220207131047.282110-7-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The mcp251xfd_chip_stop() function tries the best to stop the chip and
put it into sleep mode. It continues, even if some intermediate steps
fail. As none of the callers use the return value, let this function
return void.

Link: https://lore.kernel.org/all/20220207131047.282110-6-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch adds a new function to bring the chip into sleep mode, and
replaces several occurrences of open coded variants.

Link: https://lore.kernel.org/all/20220207131047.282110-5-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The mcp251xfd driver supports runtime PM enabled kernels, but also
works on !CONFIG_PM configurations.

This patch simplifies the runtime PM handling in the
mcp251xfd_unregister(). In the CONFIG_PM case, runtime PM has been
enabled in the mcp251xfd_probe() function, so we can disable it here.
For !CONFIG_PM builds call mcp251xfd_clks_and_vdd_disable() directly.

Link: https://lore.kernel.org/all/20220207131047.282110-4-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

MCP251XFD_REG_OSC is the first register the driver reads from. The
chip may be in deep sleep and the SPI transfer (i.e. the assertion of
the CS) will wake the chip up. This takes about 3ms. The CRC of this
transfer is wrong, or there isn't any chip at all, in this case the
CRC will be wrong, too. The driver ignores the CRC error and returns
the read data to the caller.

To avoid any confusion, this patch changes the
mcp251xfd_regmap_crc_read() function to only ignore the CRC error if
solely the OSC register is read. So when reading more than the OSC
registers at once, CRC errors are not ignored.

Link: https://lore.kernel.org/all/20220207131047.282110-3-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch renames mcp251xfd_osc_invalid() to mcp251xfd_reg_invalid(),
as it will be used for other registers than the "osc" register in a
later patch.

This patch also moves this function to more towards the beginning of
the file, to be available for other functions, too.

Link: https://lore.kernel.org/all/20220207131047.282110-2-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The input to the GENMASK() macro was calculated by hand. Replaced it
with a dedicated macro: BITS_PER_TYPE() which does the exact same job.

Link: https://lore.kernel.org/all/20220212130737.3008-1-mailhol.vincent@wanadoo.frSigned-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Add check for NAPI poll function to avoid enabling interrupts
with out completing the NAPI call.

Link: https://lore.kernel.org/all/20220208162053.39896-1-srinivas.neeli@xilinx.comSigned-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Return value from softing_startstop() directly instead of taking this
in another redundant variable.

Link: https://lore.kernel.org/all/20220112080629.667191-1-chi.minghao@zte.com.cnReported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Signed-off-by: CGEL ZTE <cgel.zte@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The ethtool core implements a default drvinfo.

There's no need to replicate this in the driver, no additional
information is added, so remove this and rely on the default.

Link: https://lore.kernel.org/all/20220124215642.3474154-10-mkl@pengutronix.de
Cc: Dario Binacchi <dariobin@libero.it>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The function usb_bulk_msg() can be called with a NULL pointer as the
"actual_length" parameter. This patch removes this variable.

Link: https://lore.kernel.org/all/20220124215642.3474154-9-mkl@pengutronix.de
Cc: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch marks the arguments of some functions as well as some local
variables as constant.

Link: https://lore.kernel.org/all/20220124215642.3474154-7-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch simplifies the validation of the fixed bit rates. If a
supported bit rate is found, directly return 0.

If no valid bit rate is found return -EINVAL;

Link: https://lore.kernel.org/all/20220124215642.3474154-6-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Commit fb8696ab ("can: gw: synchronize rcu operations
before removing gw job entry") added three synchronize_rcu() calls
to make sure one rcu grace period was observed before freeing
a "struct cgw_job" (which are tiny objects).

This should be converted to call_rcu() to avoid adding delays
in device / network dismantles.

Use the rcu_head that was already in struct cgw_job,
not yet used.

Link: https://lore.kernel.org/all/20220207190706.1499190-1-eric.dumazet@gmail.comSigned-off-by: Eric Dumazet <edumazet@google.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Since commit

| 1f923440 ("dt-bindings: can: add can-controller.yaml")

there is a common CAN controller binding. Add this to the m_can
binding.

Link: https://lore.kernel.org/all/20220124220653.3477172-4-mkl@pengutronix.deReviewed-by: Chandrasekar Ramakrishnan <rcsekar@samsung.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch fixes the indention of the table in the description of the
bosch,mram-cfg property.

Link: https://lore.kernel.org/all/20220217101111.2291151-1-mkl@pengutronix.deReviewed-by: Chandrasekar Ramakrishnan <rcsekar@samsung.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Since Sriram Dash's email bounces, change the maintainer entry to
Chandrasekar Ramakrishnan. Chandrasekar Ramakrishnan is already listed
as a maintainer in the MAINTAINERS file.

Link: https://lore.kernel.org/all/20220217113839.2311417-1-mkl@pengutronix.de
Cc: Chandrasekar Ramakrishnan <rcsekar@samsung.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Since commit

| 1f923440 ("dt-bindings: can: add can-controller.yaml")

there is a common CAN controller binding. Add this to the sun4i_can
binding.

Link: https://lore.kernel.org/all/20220124220653.3477172-3-mkl@pengutronix.de
Cc: Evgeny Boger <boger@wirenboard.com>
Cc: Gerhard Bertelsmann <info@gerhard-bertelsmann.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Since commit

| 1f923440 ("dt-bindings: can: add can-controller.yaml")

there is a common CAN controller binding. Add this to the mcp251xfd
binding.

Link: https://lore.kernel.org/all/20220124220653.3477172-2-mkl@pengutronix.de
Cc: Manivannan Sadhasivam <mani@kernel.org>
Cc: Thomas Kopp <thomas.kopp@microchip.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Subbaraya Sundeep says:

====================
Add ethtool support for completion queue event size

After a packet is sent or received by NIC then NIC posts
a completion queue event which consists of transmission status
(like send success or error) and received status(like
pointers to packet fragments). These completion events may
also use a ring similar to rx and tx rings. This patchset
introduces cqe-size ethtool parameter to modify the size
of the completion queue event if NIC hardware has that capability.
A bigger completion queue event can have more receive buffer pointers
inturn NIC can transfer a bigger frame from wire as long as
hardware(MAC) receive frame size limit is not exceeded.

Patch 1 adds support setting/getting cqe-size via
ethtool -G and ethtool -g.

Patch 2 includes octeontx2 driver changes to use
completion queue event size set from ethtool -G.
====================

Link: https://lore.kernel.org/r/1645555153-4932-1-git-send-email-sbhatta@marvell.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Completion Queue Entry(CQE) is a descriptor written
by hardware to notify software about the send and
receive completion status. The CQE can be of size
128 or 512 bytes. A 512 bytes CQE can hold more receive
fragments pointers compared to 128 bytes CQE. This
patch enables to modify CQE size using:
<ethtool -G cqe-size N>.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add support to set completion queue event size via ethtool -G
parameter and get it via ethtool -g parameter.

~ # ./ethtool -G eth0 cqe-size 512
~ # ./ethtool -g eth0
Ring parameters for eth0:
Pre-set maximums:
RX:             1048576
RX Mini:        n/a
RX Jumbo:       n/a
TX:             1048576
Current hardware settings:
RX:             256
RX Mini:        n/a
RX Jumbo:       n/a
TX:             4096
RX Buf Len:             2048
CQE Size:                128
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

This reverts commit d6ff94af.

Since commit faab39f6 ("net: allow out-of-order netdev unregistration")
fixed the issue in a better way, this patch is to revert the previous fix,
as it might bring back the old problem fixed by commit 563bcbae ("net:
vlan: fix a UAF in vlan_dev_real_dev()").
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Link: https://lore.kernel.org/r/563c0a6e48510ccbff9ef4715de37209695e9fc4.1645592097.git.lucien.xin@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

I missed the obvious case where netif_ix() is invoked from hard-IRQ
context.

Disabling bottom halves is only needed in process context. This ensures
that the code remains on the current CPU and that the soft-interrupts
are processed at local_bh_enable() time.
In hard- and soft-interrupt context this is already the case and the
soft-interrupts will be processed once the context is left (at irq-exit
time).

Disable bottom halves if neither hard-interrupts nor soft-interrupts are
disabled. Update the kernel-doc, mention that interrupts must be enabled
if invoked from process context.

Fixes: baebdf48 ("net: dev: Makes sure netif_rx() can be invoked in any context.")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/Yg05duINKBqvnxUc@linutronix.deSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Hans Schultz says:

====================
Add support for locked bridge ports (for 802.1X)

This series starts by adding support for SA filtering to the bridge,
which is then allowed to be offloaded to switchdev devices. Furthermore
an offloading implementation is supplied for the mv88e6xxx driver.

Public Local Area Networks are often deployed such that there is a
risk of unauthorized or unattended clients getting access to the LAN.
To prevent such access we introduce SA filtering, such that ports
designated as secure ports are set in locked mode, so that only
authorized source MAC addresses are given access by adding them to
the bridges forwarding database. Incoming packets with source MAC
addresses that are not in the forwarding database of the bridge are
discarded. It is then the task of user space daemons to populate the
bridge's forwarding database with static entries of authorized entities.

The most common approach is to use the IEEE 802.1X protocol to take
care of the authorization of allowed users to gain access by opening
for the source address of the authorized host.

With the current use of the bridge parameter in hostapd, there is
a limitation in using this for IEEE 802.1X port authentication. It
depends on hostapd attaching the port on which it has a successful
authentication to the bridge, but that only allows for a single
authentication per port. This patch set allows for the use of
IEEE 802.1X port authentication in a more general network context with
multiple 802.1X aware hosts behind a single port as depicted, which is
a commonly used commercial use-case, as it is only the number of
available entries in the forwarding database that limits the number of
authenticated clients.

      +--------------------------------+
      |                                |
      |      Bridge/Authenticator      |
      |                                |
      +-------------+------------------+
       802.1X port  |
                    |
                    |
             +------+-------+
             |              |
             |  Hub/Switch  |
             |              |
             +-+----------+-+
               |          |
            +--+--+    +--+--+
            |     |    |     |
    Hosts   |  a  |    |  b  |   . . .
            |     |    |     |
            +-----+    +-----+

The 802.1X standard involves three different components, a Supplicant
(Host), an Authenticator (Network Access Point) and an Authentication
Server which is typically a Radius server. This patch set thus enables
the bridge module together with an authenticator application to serve
as an Authenticator on designated ports.

For the bridge to become an IEEE 802.1X Authenticator, a solution using
hostapd with the bridge driver can be found at
https://github.com/westermo/hostapd/tree/bridge_driver .

The relevant components work transparently in relation to if it is the
bridge module or the offloaded switchcore case that is in use.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

These tests check that the basic locked port feature works, so that
no 'host' can communicate (ping) through a locked port unless the
MAC address of the 'host' interface is in the forwarding database of
the bridge.
Signed-off-by: Hans Schultz <schultz.hans+netdev@gmail.com>
Acked-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Supporting bridge ports in locked mode using the drop on lock
feature in Marvell mv88e6xxx switchcores is described in the
'88E6096/88E6097/88E6097F Datasheet', sections 4.4.6, 4.4.7 and
5.1.2.1 (Drop on Lock).

This feature is implemented here facilitated by the locked port flag.
Signed-off-by: Hans Schultz <schultz.hans+netdev@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ensures that the DSA switch driver gets notified of changes to the
BR_PORT_LOCKED flag as well, for the case when a DSA port joins or
leaves a LAG that is a bridge port.
Signed-off-by: Hans Schultz <schultz.hans+netdev@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Various switchcores support setting ports in locked mode, so that
clients behind locked ports cannot send traffic through the port
unless a fdb entry is added with the clients MAC address.
Signed-off-by: Hans Schultz <schultz.hans+netdev@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In a 802.1X scenario, clients connected to a bridge port shall not
be allowed to have traffic forwarded until fully authenticated.
A static fdb entry of the clients MAC address for the bridge port
unlocks the client and allows bidirectional communication.

This scenario is facilitated with setting the bridge port in locked
mode, which is also supported by various switchcore chipsets.
Signed-off-by: Hans Schultz <schultz.hans+netdev@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>