The number of TX descriptors per packet is an unsigned value and
the variable for holding this information should be unsigned.

This patch replaces the data type of num_tx_desc variable in struct
ravb_private from 'int' to 'unsigned int'.
This patch also updates the data type of local variables to unsigned int,
where the local variables are evaluated using num_tx_desc.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ARRAY_SIZE macro is defined to get an array's size which is
more compact and more formal in linux source. Thus, we can replace
the long sizeof(arr)/sizeof(arr[0]) with the compact ARRAY_SIZE.
Signed-off-by: Jason Wang <wangborong@cdjrlc.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20210817121106.44189-1-wangborong@cdjrlc.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Currently, the declaration of fill_imix_distribution() is dependent
on CONFIG_XFRM. This is incorrect.

Move fill_imix_distribution() declaration out of #ifndef CONFIG_XFRM
block.
Signed-off-by: Nick Richardson <richardsonnick@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add gfp_t mask as an input parameter to mem_cgroup_charge_skmem(),
to give more control to the networking stack and enable it to change
memcg charging behavior. In the future, the networking stack may decide
to avoid oom-kills when fallbacks are more appropriate.

One behavior change in mem_cgroup_charge_skmem() by this patch is to
avoid force charging by default and let the caller decide when and if
force charging is needed through the presence or absence of
__GFP_NOFAIL.
Signed-off-by: Wei Wang <weiwan@google.com>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

VLAN TCI is a 16 bit field which includes Priority(3 bits),
CFI(1 bit) and VID(12 bits). Currently ntuple filters support
installing rules to steer packets based on VID only.
This patch extends that support such that filters can
be installed for entire VLAN TCI.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 09e856d5 ("vrf: Reset skb conntrack connection on VRF rcv")
fixes the "reverse-DNAT" of an SNAT-ed packet over a VRF.

This patch adds a test for this scenario.
Signed-off-by: Lahav Schlesinger <lschlesinger@drivenets.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is only one caller for ops_free(), so inline it.
Separate net_drop_ns() and net_free(), so the net_free()
can be called directly.
Add free_exit_list() helper function for free net_exit_list.

====================
v2:
 - v1 does not apply, rebase it.
====================
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for tag_sja1105 running on non-sja1105 DSA ports, by making
sure that every time we dereference dp->priv, we check the switch's
dsa_switch_ops (otherwise we access a struct sja1105_port structure that
is in fact something else).

This adds an unconditional build-time dependency between sja1105 being
built as module => tag_sja1105 must also be built as module. This was
there only for PTP before.

Some sane defaults must also take place when not running on sja1105
hardware. These are:

- sja1105_xmit_tpid: the sja1105 driver uses different VLAN protocols
  depending on VLAN awareness and switch revision (when an encapsulated
  VLAN must be sent). Default to 0x8100.

- sja1105_rcv_meta_state_machine: this aggregates PTP frames with their
  metadata timestamp frames. When running on non-sja1105 hardware, don't
  do that and accept all frames unmodified.

- sja1105_defer_xmit: calls sja1105_port_deferred_xmit in sja1105_main.c
  which writes a management route over SPI. When not running on sja1105
  hardware, bypass the SPI write and send the frame as-is.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Bongsu Jeon says:

====================
Update the virtual NCI device driver and add the NCI testcase

This series updates the virtual NCI device driver and NCI selftest code
and add the NCI test case in selftests.

1/8 to use wait queue in virtual device driver.
2/8 to remove the polling code in selftests.
3/8 to fix a typo.
4/8 to fix the next nlattr offset calculation.
5/8 to fix the wrong condition in if statement.
6/8 to add a flag parameter to the Netlink send function.
7/8 to extract the start/stop discovery function.
8/8 to add the NCI testcase in selftests.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the NCI testcase reading T4T Tag that has NFC TEST in plain text.
the virtual device application acts as T4T Tag in this testcase.
Signed-off-by: Bongsu Jeon <bongsu.jeon@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To reuse the start/stop discovery code in other testcase, extract the code.
Signed-off-by: Bongsu Jeon <bongsu.jeon@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To reuse the send_cmd_mt_nla for NLM_F_REQUEST and NLM_F_DUMP flag,
add the flags parameter to the function.
Signed-off-by: Bongsu Jeon <bongsu.jeon@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

memcpy should be executed only in case nla_len's value is greater than 0.
Signed-off-by: Bongsu Jeon <bongsu.jeon@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

nlattr could have a padding for 4 bytes alignment. So next nla's offset
should be calculated with a padding.
Signed-off-by: Bongsu Jeon <bongsu.jeon@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix typo: rep_len -> resp_len
Signed-off-by: Bongsu Jeon <bongsu.jeon@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Because the virtual NCI device uses Wait Queue, the virtual device
application doesn't need to poll the NCI frame.
Signed-off-by: Bongsu Jeon <bongsu.jeon@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In previous version, the user level virtual device application that used
this driver should have the polling scheme to read a NCI frame.
To remove this polling scheme, use Wait Queue.
Signed-off-by: Bongsu Jeon <bongsu.jeon@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add seq_puts() statement for dev_mcast, make it more readable.
As also, keep vertical alignment for {dev, ptype, dev_mcast} that
under /proc/net.
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make all dependent RxRPC kconfig entries be dependent on AF_RXRPC
so that they are presented (indented) after AF_RXRPC instead
of being presented at the same level on indentation.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Marc Dionne <marc.dionne@auristor.com>
Cc: linux-afs@lists.infradead.org
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

Mat Martineau says:

====================
mptcp: Add full mesh path manager option

The path manager in MPTCP controls the creation of additional subflows
after the initial connection is created. As each peer advertises
available endpoints with the ADD_ADDR MPTCP option, the recipient of
those advertisements must decide which subflows to create from the known
local and remote interfaces that are available for use by MPTCP.

The existing in-kernel path manager will create one additional subflow
when an ADD_ADDR is received, or a local address is newly configured for
MPTCP use. The maximum number of subflows has a configurable limit.

This patch set adds a MPTCP_PM_ADDR_FLAG_FULLMESH flag to the MPTCP
netlink API that enables subflows to be created more aggressively. When
an ADD_ADDR is received from a peer, new subflows are created between
that address/port and all local addresses configured for MPTCP.
Similarly, when a new local address is newly configured for use by
MPTCP, new subflows are created between that local address and all known
remote addresses for that MPTCP connection. The configurable limit on
the number of subflows still applies. If the new flag is not used the
path manager behavior is unchanged.

Patch 1 adds a helper function and refactors another function to prepare
for the rest of the patch series.

Patches 2 and 3 add two mesh connection capabilities: initiating
subflows based on added local addresses, or reacting to incoming
advertisements.

Patches 4-6 add full mesh cases to the self tests.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The removing addresses testcases can only deal with the continuous ids.
This patch added the uncontinuous removing ids support.
Signed-off-by: Geliang Tang <geliangtang@xiaomi.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch added the testcases for the fullmesh address flag of the path
manager.
Co-developed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Geliang Tang <geliangtang@xiaomi.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch dealt with the MPTCP_PM_ADDR_FLAG_FULLMESH flag in add_addr()
and print_addr(), to set and print out the fullmesh flag.
Signed-off-by: Geliang Tang <geliangtang@xiaomi.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In mptcp_pm_nl_add_addr_received(), fill a temporary allocate array of
all local address corresponding to the fullmesh endpoint. If such array
is empty, keep the current behavior.

Elsewhere loop on such array and create a subflow for each local address
towards the given remote address
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Geliang Tang <geliangtang@xiaomi.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch added and managed a new per endpoint flag, named
MPTCP_PM_ADDR_FLAG_FULLMESH.

In mptcp_pm_create_subflow_or_signal_addr(), if such flag is set, instead
of:
        remote_address((struct sock_common *)sk, &remote);
fill a temporary allocated array of all known remote address. After
releaseing the pm lock loop on such array and create a subflow for each
remote address from the given local.

Note that the we could still use an array even for non 'fullmesh'
endpoint: with a single entry corresponding to the primary MPC subflow
remote address.
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Geliang Tang <geliangtang@xiaomi.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch added a new helper mptcp_pm_get_flags_and_ifindex_by_id(),
and used it in __mptcp_subflow_connect() to get the flags and ifindex
values.

Then the two arguments flags and ifindex of __mptcp_subflow_connect()
can be dropped.
Signed-off-by: Geliang Tang <geliangtang@xiaomi.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Nguyen, Anthony L says:

====================
40GbE Intel Wired LAN Driver Updates 2021-08-17

This series contains updates to iavf and i40e drivers.

Stefan Assmann converts use of flag based locking of critical sections
to mutexes for iavf.

Colin King fixes a spelling error for i40e.

* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
  i40e: Fix spelling mistake "dissable" -> "disable"
  iavf: use mutexes for locking of critical sections
====================

Link: https://lore.kernel.org/r/20210817203549.3529860-1-anthony.l.nguyen@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

There is a spelling mistake in a dev_info message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

As follow-up to the discussion with Jakub Kicinski about iavf locking
being insufficient [1] convert iavf to use mutexes instead of bitops.
The locking logic is kept as is, just a drop-in replacement of
enum iavf_critical_section_t with separate mutexes.
The only difference is that the mutexes will be destroyed before the
module is unloaded.

[1] https://lwn.net/ml/netdev/20210316150210.00007249%40intel.com/Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Marek Szlosek <marek.szlosek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

As previously discussed with David Ahern, here is a refactored and improved
version of the IOAM self-test. It is now more complete and more robust. Now,
all tests are divided into three categories: OUTPUT (evaluates the IOAM
processing by the sender), INPUT (evaluates the IOAM processing by the receiver)
and GLOBAL (evaluates wider use cases that do not fall into the other two
categories). Both OUTPUT and INPUT tests only use a two-node topology (alpha and
beta), while GLOBAL tests use the entire three-node topology (alpha, beta,
gamma). Each test is documented inside its own handler in the (bash) script.
Signed-off-by: Justin Iurman <justin.iurman@uliege.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

Nikolay Aleksandrov says:

====================
net: bridge: vlan: fixes for vlan mcast contexts

These are four fixes for vlan multicast contexts. The first patch enables
mcast ctx snooping when adding already existing master vlans to be
consistent with the rest of the code. The second patch accounts for the
mcast ctx router ports when allocating skb for notification. The third
one fixes two suspicious rcu usages due to wrong vlan group helper, and
the fourth updates host vlan mcast state along with port mcast state.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When changing vlan mcast state by br_multicast_toggle_vlan it iterates
over all ports and enables/disables the port mcast ctx based on the new
state, but I forgot to update the host vlan (bridge master vlan entry)
with the new state so it will be left out. Also that function is not
used outside of br_multicast.c, so make it static.

Fixes: f4b7002a ("net: bridge: add vlan mcast snooping knob")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When dereferencing the port vlan group we should use the rcu helper
instead of the one relying on rtnl. In br_multicast_pg_to_port_ctx the
entry cannot disappear as we hold the multicast lock and rcu as explained
in the comment above it.
For the same reason we're ok in br_multicast_start_querier.

 =============================
 WARNING: suspicious RCU usage
 5.14.0-rc5+ #429 Tainted: G        W
 -----------------------------
 net/bridge/br_private.h:1478 suspicious rcu_dereference_protected() usage!

 other info that might help us debug this:

 rcu_scheduler_active = 2, debug_locks = 1
 3 locks held by swapper/2/0:
  #0: ffff88822be85eb0 ((&p->timer)){+.-.}-{0:0}, at: call_timer_fn+0x5/0x2da
  #1: ffff88810b32f260 (&br->multicast_lock){+.-.}-{3:3}, at: br_multicast_port_group_expired+0x28/0x13d [bridge]
  #2: ffffffff824f6c80 (rcu_read_lock){....}-{1:3}, at: rcu_lock_acquire.constprop.0+0x0/0x22 [bridge]

 stack backtrace:
 CPU: 2 PID: 0 Comm: swapper/2 Kdump: loaded Tainted: G        W         5.14.0-rc5+ #429
 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-4.fc34 04/01/2014
 Call Trace:
  <IRQ>
  dump_stack_lvl+0x45/0x59
  nbp_vlan_group+0x3e/0x44 [bridge]
  br_multicast_pg_to_port_ctx+0xd6/0x10d [bridge]
  br_multicast_star_g_handle_mode+0xa1/0x2ce [bridge]
  ? netlink_broadcast+0xf/0x11
  ? nlmsg_notify+0x56/0x99
  ? br_mdb_notify+0x224/0x2e9 [bridge]
  ? br_multicast_del_pg+0x1dc/0x26d [bridge]
  br_multicast_del_pg+0x1dc/0x26d [bridge]
  br_multicast_port_group_expired+0xaa/0x13d [bridge]
  ? __grp_src_delete_marked.isra.0+0x35/0x35 [bridge]
  ? __grp_src_delete_marked.isra.0+0x35/0x35 [bridge]
  call_timer_fn+0x134/0x2da
  __run_timers+0x169/0x193
  run_timer_softirq+0x19/0x2d
  __do_softirq+0x1bc/0x42a
  __irq_exit_rcu+0x5c/0xb3
  irq_exit_rcu+0xa/0x12
  sysvec_apic_timer_interrupt+0x5e/0x75
  </IRQ>
  asm_sysvec_apic_timer_interrupt+0x12/0x20
 RIP: 0010:default_idle+0xc/0xd
 Code: e8 14 40 71 ff e8 10 b3 ff ff 4c 89 e2 48 89 ef 31 f6 5d 41 5c e9 a9 e8 c2 ff cc cc cc cc 0f 1f 44 00 00 e8 7f 55 65 ff fb f4 <c3> 0f 1f 44 00 00 55 65 48 8b 2c 25 40 6f 01 00 53 f0 80 4d 02 20
 RSP: 0018:ffff88810033bf00 EFLAGS: 00000206
 RAX: ffffffff819cf828 RBX: ffff888100328000 RCX: 0000000000000001
 RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffffffff819cfa2d
 RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000001
 R10: ffff8881008302c0 R11: 00000000000006db R12: 0000000000000000
 R13: 0000000000000002 R14: 0000000000000000 R15: 0000000000000000
  ? __sched_text_end+0x4/0x4
  ? default_idle_call+0x15/0x7b
  default_idle_call+0x4d/0x7b
  do_idle+0x124/0x2a2
  cpu_startup_entry+0x1d/0x1f
  secondary_startup_64_no_verify+0xb0/0xbb

Fixes: 74edfd48 ("net: bridge: multicast: add helper to get port mcast context from port group")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When sending a global vlan notification we should account for the number
of router ports when allocating the skb, otherwise we might end up
losing notifications.

Fixes: dc002875 ("net: bridge: vlan: use br_rports_fill_info() to export mcast router ports")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We always create a vlan with enabled mcast snooping, so when the user
turns on per-vlan mcast contexts they'll get consistent behaviour with
the current situation, but one place wasn't updated when a bridge/master
vlan which already exists (created due to port vlans) is being added as
real bridge vlan (BRIDGE_VLAN_INFO_BRENTRY). We need to enable mcast
snooping for that vlan when that happens.

Fixes: 7b54aaaf ("net: bridge: multicast: add vlan state initialization and control")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Subbaraya Sundeep says:

====================
octeontx2: Rework MCAM flows management for VFs

From Octeontx2 hardware point of view there is no
difference between PFs and VFs. Hence with refactoring
in driver the packet classification features or offloads
can be supported by VFs also. This patchset unifies the
mcam flows management so that VFs can also support
ntuple filters. Since there are MCAM allocations by
all PFs and VFs in the system it is required to have
the ability to modify number of mcam rules count
for a PF/VF in runtime. This is achieved by using devlink.
Below is the summary of patches:

Patch 1,2,3 are trivial patches which helps in debugging
in case of errors by using custom error codes and
displaying proper error messages.

Patches 4,5 brings rx-all and ntuple support
for CGX mapped VFs and LBK VFs.

Patches 6,7,8 brings devlink support to
PF netdev driver so that mcam entries count
can be changed at runtime.
To change mcam rule count at runtime where multiple rule
allocations are done sorting is required.
Also both ntuple and TC rules needs to be unified.

Patch 9 is related to AF NPC where a PF
allocated entries are allocated at bottom(low priority).

On CN10K there is slight change in reading
NPC counters which is handled by patch 10.

Patch 11 is to allow packets from CPT for
NPC parsing on CN10K.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

On CN10K, the higher bits in the channel number represents the CPT
channel number. Mask out these higher bits in the npc configuration
to allow packets from cpt for parsing.
Signed-off-by: Vidya <vvelumuri@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The way SW can identify the number NPC counters supported by silicon
has changed for CN10K. This patch addresses this reading appropriate
registers to find out number of counters available.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the mcam entry allocation request is from PF
and NOT a priority allocation request then allocate
low priority entries so that PF entries always have
lower priority than its VFs. This is required so
that entries with (base) MCAM match criteria have lower
priority compared to entries with (base + additional)
match criteria. This patch considers only best case
scenario where PF entries are allocated from low
priority zone if low priority zone has free space.
There are worst case scenarios like:
1. VFs allocating hundreds of MCAM entries leading to VFs
using all mid priority zone and low priority zone entries
hence no entries free from low priority zone for PF.
2. All the PFs and VFs in the system allocating and freeing
entries causing fragmentation in MCAM space and all the
entries requested by PF could not fit in low priority
zone for allocation.
This patch do not handle worst case scenarios.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Added support for setting or modifying MCAM entry count at
runtime via devlink params.

commands:
  devlink dev param show
pci/0002:02:00.0:
  name mcam_count type driver-specific
    values:
      cmode runtime value 16

  devlink dev param set pci/0002:02:00.0 name mcam_count
				value 64 cmode runtime
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>