Pull drm fixes from Dave Airlie:
 "i915, nouveau and amdgpu/radeon fixes in this:

  nouveau:
     Two fixes, one for a regression with dithering and one for a bug
     hit by the userspace drivers.

  i915:
     A few fixes, mostly things heading for stable, two important
     skylake GT3/4 hangs.

  radeon/amdgpu:
     Some audio, suspend/resume and some runtime PM fixes, along with
     two patches to harden the userptr ABI a bit"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (24 commits)
  drm: Loongson-3 doesn't fully support wc memory
  drm/nouveau/gr/gf100: select a stream master to fixup tfb offset queries
  amdgpu/uvd: add uvd fw version for amdgpu
  drm/amdgpu: forbid mapping of userptr bo through radeon device file
  drm/radeon: forbid mapping of userptr bo through radeon device file
  drm/amdgpu: bump the afmt limit for CZ, ST, Polaris
  drm/amdgpu: use defines for CRTCs and AMFT blocks
  drm/dp/mst: Validate port in drm_dp_payload_send_msg()
  drm/nouveau/kms: fix setting of default values for dithering properties
  drm/radeon: print a message if ATPX dGPU power control is missing
  Revert "drm/radeon: disable runtime pm on PX laptops without dGPU power control"
  drm/amdgpu/acp: fix resume on CZ systems with AZ audio
  drm/radeon: add a quirk for a XFX R9 270X
  drm/radeon: print pci revision as well as pci ids on driver load
  drm/i915: Use fw_domains_put_with_fifo() on HSW
  drm/i915: Force ringbuffers to not be at offset 0
  drm/i915: Adjust size of PIPE_CONTROL used for gen8 render seqno write
  drm/i915/skl: Fix spurious gpu hang with gt3/gt4 revs
  drm/i915/skl: Fix rc6 based gpu/system hang
  drm/i915/userptr: Hold mmref whilst calling get-user-pages
  ...

Pull sound fixes from Takashi Iwai:
 "Again a relatively calm week without surprise: most of fixes are about
  HD-audio, including fixes for Cirrus codec regression and a race over
  regmap access.  Although both change are slightly unintuitive, the
  risk of further breakage is quite low, I hope.

  Other than that, all the rest are trivial"

* tag 'sound-4.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda - Fix possible race on regmap bypass flip
  ALSA: pcxhr: Fix missing mutex unlock
  ALSA: hda - add PCI ID for Intel Broxton-T
  ALSA: hda - Keep powering up ADCs on Cirrus codecs
  ALSA: hda/realtek - Add ALC3234 headset mode for Optiplex 9020m
  ALSA - hda: hdmi check NULL pointer in hdmi_set_chmap
  ALSA: hda - Don't trust the reported actual power state

Misc radeon and amdgpu bug fixes for 4.6.

* 'drm-fixes-4.6' of git://people.freedesktop.org/~agd5f/linux:
  amdgpu/uvd: add uvd fw version for amdgpu
  drm/amdgpu: forbid mapping of userptr bo through radeon device file
  drm/radeon: forbid mapping of userptr bo through radeon device file
  drm/amdgpu: bump the afmt limit for CZ, ST, Polaris
  drm/amdgpu: use defines for CRTCs and AMFT blocks
  drm/radeon: print a message if ATPX dGPU power control is missing
  Revert "drm/radeon: disable runtime pm on PX laptops without dGPU power control"
  drm/amdgpu/acp: fix resume on CZ systems with AZ audio
  drm/radeon: add a quirk for a XFX R9 270X
  drm/radeon: print pci revision as well as pci ids on driver load
  drm/amdgpu: when suspending, if uvd/vce was running. need to cancel delay work.
  drm/radeon: fix initial connector audio value

Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: stable@vger.kernel.org
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

transform feedback fix.

* 'linux-4.6' of git://github.com/skeggsb/linux:
  drm/nouveau/gr/gf100: select a stream master to fixup tfb offset queries

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: stable@vger.kernel.org

Was previously always hardcoded to 0.
Signed-off-by: Sonny Jiang <sonny.jiang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Allowing userptr bo which are basicly a list of page from some vma
(so either anonymous page or file backed page) would lead to serious
corruption of kernel structures and counters (because we overwrite
the page->mapping field when mapping buffer).

This will already block if the buffer was populated before anyone does
try to mmap it because then TTM_PAGE_FLAG_SG would be set in in the
ttm_tt flags. But that flag is check before ttm_tt_populate in the ttm
vm fault handler.

So to be safe just add a check to verify_access() callback.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Jérôme Glisse <jglisse@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Allowing userptr bo which are basicly a list of page from some vma
(so either anonymous page or file backed page) would lead to serious
corruption of kernel structures and counters (because we overwrite
the page->mapping field when mapping buffer).

This will already block if the buffer was populated before anyone does
try to mmap it because then TTM_PAGE_FLAG_SG would be set in in the
ttm_tt flags. But that flag is check before ttm_tt_populate in the ttm
vm fault handler.

So to be safe just add a check to verify_access() callback.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Jérôme Glisse <jglisse@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Fixes array overflow on these chips.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Prerequiste for the next patch which ups the limits.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

With the joys of things running concurrently, there's always a chance
that the port we get passed in drm_dp_payload_send_msg() isn't actually
valid anymore. Because of this, we need to make sure we validate the
reference to the port before we use it otherwise we risk running into
various race conditions. For instance, on the Dell MST monitor I have
here for testing, hotplugging it enough times causes us to kernel panic:

[drm:intel_mst_enable_dp] 1
[drm:drm_dp_update_payload_part2] payload 0 1
[drm:intel_get_hpd_pins] hotplug event received, stat 0x00200000, dig 0x10101011, pins 0x00000020
[drm:intel_hpd_irq_handler] digital hpd port B - short
[drm:intel_dp_hpd_pulse] got hpd irq on port B - short
[drm:intel_dp_check_mst_status] got esi 00 10 00
[drm:drm_dp_update_payload_part2] payload 1 1
general protection fault: 0000 [#1] SMP
…
Call Trace:
 [<ffffffffa012b632>] drm_dp_update_payload_part2+0xc2/0x130 [drm_kms_helper]
 [<ffffffffa032ef08>] intel_mst_enable_dp+0xf8/0x180 [i915]
 [<ffffffffa0310dbd>] haswell_crtc_enable+0x3ed/0x8c0 [i915]
 [<ffffffffa030c84d>] intel_atomic_commit+0x5ad/0x1590 [i915]
 [<ffffffffa01db877>] ? drm_atomic_set_crtc_for_connector+0x57/0xe0 [drm]
 [<ffffffffa01dc4e7>] drm_atomic_commit+0x37/0x60 [drm]
 [<ffffffffa0130a3a>] drm_atomic_helper_set_config+0x7a/0xb0 [drm_kms_helper]
 [<ffffffffa01cc482>] drm_mode_set_config_internal+0x62/0x100 [drm]
 [<ffffffffa01d02ad>] drm_mode_setcrtc+0x3cd/0x4e0 [drm]
 [<ffffffffa01c18e3>] drm_ioctl+0x143/0x510 [drm]
 [<ffffffffa01cfee0>] ? drm_mode_setplane+0x1b0/0x1b0 [drm]
 [<ffffffff810f79a7>] ? hrtimer_start_range_ns+0x1b7/0x3a0
 [<ffffffff81212962>] do_vfs_ioctl+0x92/0x570
 [<ffffffff81590852>] ? __sys_recvmsg+0x42/0x80
 [<ffffffff81212eb9>] SyS_ioctl+0x79/0x90
 [<ffffffff816b4e32>] entry_SYSCALL_64_fastpath+0x1a/0xa4
RIP  [<ffffffffa012b026>] drm_dp_payload_send_msg+0x146/0x1f0 [drm_kms_helper]

Which occurs because of the hotplug event shown in the log, which ends
up causing DRM's dp helpers to drop the port we're updating the payload
on and panic.

CC: stable@vger.kernel.org
Signed-off-by: Lyude <cpaul@redhat.com>
Reviewed-by: David Airlie <airlied@linux.ie>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Single nouveau regression fix
* 'linux-4.6' of git://github.com/skeggsb/linux:
  drm/nouveau/kms: fix setting of default values for dithering properties

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Hi Dave, fixes all around, all but one are cc: stable material, the most
important ones are likely the Skylake hang fixes from Mika.

* tag 'drm-intel-fixes-2016-04-21' of git://anongit.freedesktop.org/drm-intel:
  drm/i915: Use fw_domains_put_with_fifo() on HSW
  drm/i915: Force ringbuffers to not be at offset 0
  drm/i915: Adjust size of PIPE_CONTROL used for gen8 render seqno write
  drm/i915/skl: Fix spurious gpu hang with gt3/gt4 revs
  drm/i915/skl: Fix rc6 based gpu/system hang
  drm/i915/userptr: Hold mmref whilst calling get-user-pages
  drm/i915: Fixup the free space logic in ring_prepare
  drm/i915/skl+: Use plane size for relative data rate calculation

Pull RTC fixes from Alexandre Belloni:
 "A few fixes for the RTC subsystem.  The documentation fix already
  missed 4.5 so I think it is worth taking it now:

  A documentation fix for s3c and two fixes for the ds1307"

* tag 'rtc-4.6-3' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
  rtc: ds1307: Use irq when available for wakeup-source device
  rtc: ds1307: ds3231 temperature s16 overflow
  rtc: s3c: Document in binding that only s3c6410 needs a src clk

Pull power management fixes from Rafael Wysocki:
 "Two fixes for issues introduced recently, one for an intel_pstate
  driver problem uncovered by the recent switch over from using timers
  and the other one for a potential cpufreq core problem related to
  system suspend/resume.

  Specifics:

   - Fix an intel_pstate driver problem causing CPUs to get stuck in the
     highest P-state when completely idle uncovered by the recent switch
     over from using timers (Rafael Wysocki).

   - Avoid attempts to get the current CPU frequency when all devices
     (like I2C controllers that may be nedded for that purpose) have
     been suspended during system suspend/resume (Rafael Wysocki)"

* tag 'pm+acpi-4.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  cpufreq: Abort cpufreq_update_current_freq() for cpufreq_suspended set
  intel_pstate: Avoid getting stuck in high P-states when idle

With commit 8bc2a407 ("rtc: ds1307: add support for the
DT property 'wakeup-source'") we lost the ability for rtc irq
functionality for devices that are actually hooked on a real IRQ
line and have capability to wakeup as well. This is not an expected
behavior. So, instead of just not requesting IRQ, skip the IRQ
requirement only if interrupts are not defined for the device.

Fixes: 8bc2a407 ("rtc: ds1307: add support for the DT property 'wakeup-source'")
Reported-by: Tony Lindgren <tony@atomide.com>
Cc: Michael Lange <linuxstuff@milaw.biz>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

while retrieving temperature from ds3231, the result may be overflow
since s16 is too small for a multiplication with 250.

ie. if temp_buf[0] == 0x2d, the result (s16 temp) will be negative.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Tested-by: Michael Tatarinov <kukabu@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

Pull networking fixes from David Miller:

 1) Fix memory leak in iwlwifi, from Matti Gottlieb.

 2) Add missing registration of netfilter arp_tables into initial
    namespace, from Florian Westphal.

 3) Fix potential NULL deref in DecNET routing code.

 4) Restrict NETLINK_URELEASE to truly bound sockets only, from Dmitry
    Ivanov.

 5) Fix dst ref counting in VRF, from David Ahern.

 6) Fix TSO segmenting limits in i40e driver, from Alexander Duyck.

 7) Fix heap leak in PACKET_DIAG_MCLIST, from Mathias Krause.

 8) Ravalidate IPV6 datagram socket cached routes properly, particularly
    with UDP, from Martin KaFai Lau.

 9) Fix endian bug in RDS dp_ack_seq handling, from Qing Huang.

10) Fix stats typing in bcmgenet driver, from Eric Dumazet.

11) Openvswitch needs to orphan SKBs before ipv6 fragmentation handing,
    from Joe Stringer.

12) SPI device reference leak in spi_ks8895 PHY driver, from Mark Brown.

13) atl2 doesn't actually support scatter-gather, so don't advertise the
    feature.  From Ben Hucthings.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (72 commits)
  openvswitch: use flow protocol when recalculating ipv6 checksums
  Driver: Vmxnet3: set CHECKSUM_UNNECESSARY for IPv6 packets
  atl2: Disable unimplemented scatter/gather feature
  net/mlx4_en: Split SW RX dropped counter per RX ring
  net/mlx4_core: Don't allow to VF change global pause settings
  net/mlx4_core: Avoid repeated calls to pci enable/disable
  net/mlx4_core: Implement pci_resume callback
  net: phy: spi_ks8895: Don't leak references to SPI devices
  net: ethernet: davinci_emac: Fix platform_data overwrite
  net: ethernet: davinci_emac: Fix Unbalanced pm_runtime_enable
  qede: Fix single MTU sized packet from firmware GRO flow
  qede: Fix setting Skb network header
  qede: Fix various memory allocation error flows for fastpath
  tcp: Merge tx_flags and tskey in tcp_shifted_skb
  tcp: Merge tx_flags and tskey in tcp_collapse_retrans
  drivers: net: cpsw: fix wrong regs access in cpsw_ndo_open
  tcp: Fix SOF_TIMESTAMPING_TX_ACK when handling dup acks
  openvswitch: Orphan skbs before IPv6 defrag
  Revert "Prevent NUll pointer dereference with two PHYs on cpsw"
  VSOCK: Only check error on skb_recv_datagram when skb is NULL
  ...

When using masked actions the ipv6_proto field of an action
to set IPv6 fields may be zero rather than the prevailing protocol
which will result in skipping checksum recalculation.

This patch resolves the problem by relying on the protocol
in the flow key rather than that in the set field action.

Fixes: 83d2b9ba ("net: openvswitch: Support masked set actions.")
Cc: Jarno Rajahalme <jrajahalme@nicira.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For IPv6, if the device indicates that the checksum is correct, set
CHECKSUM_UNNECESSARY.
Reported-by: Subbarao Narahari <snarahari@vmware.com>
Signed-off-by: Shrikrishna Khare <skhare@vmware.com>
Signed-off-by: Jin Heo <heoj@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

atl2 includes NETIF_F_SG in hw_features even though it has no support
for non-linear skbs.  This bug was originally harmless since the
driver does not claim to implement checksum offload and that used to
be a requirement for SG.

Now that SG and checksum offload are independent features, if you
explicitly enable SG *and* use one of the rare protocols that can use
SG without checkusm offload, this potentially leaks sensitive
information (before you notice that it just isn't working).  Therefore
this obscure bug has been designated CVE-2016-2117.
Reported-by: Justin Yackoski <jyackoski@crypto-nite.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Fixes: ec5f0615 ("net: Kill link between CSUM and SG features.")
Signed-off-by: David S. Miller <davem@davemloft.net>

Or Gerlitz says:

====================
Mellaox 40G driver fixes for 4.6-rc

With the fix for ARM bug being under the works, these are
few other fixes for mlx4 we have ready to go.

Eran addressed the problematic/wrong reporting of dropped packets, Daniel
fixed some matters related to PPC EEH's and Jenny's patch makes sure
VFs can't change the port's pause settings.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Count SW packet drops per RX ring instead of a global counter. This
will allow monitoring the number of rx drops per ring.

In addition, SW rx_dropped counter was overwritten by HW rx_dropped
counter, sum both of them instead to show the accurate value.

Fixes: a3333b35 ('net/mlx4_en: Moderate ethtool callback to [...] ')
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reported-by: Brenden Blanco <bblanco@plumgrid.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently changing global pause settings is done via SET_PORT
command with input modifier GENERAL. This command is allowed
for each VF since MTU setting is done via the same command.

Change the above to the following scheme: before passing the
request to the FW, the PF will check whether it was issued
by a slave. If yes, don't change global pause and warn,
otherwise change to the requested value and store for
further reference.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Maintain the PCI status and provide wrappers for enabling and disabling
the PCI device.  Performing the actions more than once without doing
its opposite results in warning logs.

This occurred when EEH hotplugged the device causing a warning for
disabling an already disabled device.

Fixes: 2ba5fbd6 ('net/mlx4_core: Handle AER flow properly')
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move resume related activities to a new pci_resume function instead of
performing them in mlx4_pci_slot_reset.  This change is needed to avoid
a hotplug during EEH recovery due to commit f2da4ccf ("powerpc/eeh:
More relaxed hotplug criterion").

Fixes: 2ba5fbd6 ('net/mlx4_core: Handle AER flow properly')
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ks8895 driver is using spi_dev_get() apparently just to take a copy
of the SPI device used to instantiate it but never calls spi_dev_put()
to free it.  Since the device is guaranteed to exist between probe() and
remove() there should be no need for the driver to take an extra
reference to it so fix the leak by just using a straight assignment.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the DaVinci emac driver is removed and re-probed, the actual
pdev->dev.platform_data is populated with an unwanted valid pointer saved by
the previous davinci_emac_of_get_pdata() call, causing a kernel crash when
calling priv->int_disable() in emac_int_disable().

Unable to handle kernel paging request at virtual address c8622a80
...
[<c0426fb4>] (emac_int_disable) from [<c0427700>] (emac_dev_open+0x290/0x5f8)
[<c0427700>] (emac_dev_open) from [<c04c00ec>] (__dev_open+0xb8/0x120)
[<c04c00ec>] (__dev_open) from [<c04c0370>] (__dev_change_flags+0x88/0x14c)
[<c04c0370>] (__dev_change_flags) from [<c04c044c>] (dev_change_flags+0x18/0x48)
[<c04c044c>] (dev_change_flags) from [<c052bafc>] (devinet_ioctl+0x6b4/0x7ac)
[<c052bafc>] (devinet_ioctl) from [<c04a1428>] (sock_ioctl+0x1d8/0x2c0)
[<c04a1428>] (sock_ioctl) from [<c014f054>] (do_vfs_ioctl+0x41c/0x600)
[<c014f054>] (do_vfs_ioctl) from [<c014f2a4>] (SyS_ioctl+0x6c/0x7c)
[<c014f2a4>] (SyS_ioctl) from [<c000ff60>] (ret_fast_syscall+0x0/0x1c)

Fixes: 42f59967 ("net: ethernet: davinci_emac: add OF support")
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to avoid an Unbalanced pm_runtime_enable in the DaVinci
emac driver when the device is removed and re-probed, and a
pm_runtime_disable() call in davinci_emac_remove().

Actually, using unbind/bind on a TI DM8168 SoC gives :
$ echo 4a120000.ethernet > /sys/bus/platform/drivers/davinci_emac/unbind
net eth1: DaVinci EMAC: davinci_emac_remove()
$ echo 4a120000.ethernet > /sys/bus/platform/drivers/davinci_emac/bind
davinci_emac 4a120000.ethernet: Unbalanced pm_runtime_enable

Cc: Brian Hutchinson <b.hutchman@gmail.com>
Fixes: 3ba97381 ("net: ethernet: davinci_emac: add pm_runtime support")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

* pm-cpufreq-fixes:
  cpufreq: Abort cpufreq_update_current_freq() for cpufreq_suspended set
  intel_pstate: Avoid getting stuck in high P-states when idle

Manish Chopra says:

====================
qede: Bug fixes

This series fixes -

* various memory allocation failure flows for fastpath
* issues with respect to driver GRO packets handling

V1->V2

* Send series against net instead of net-next.

Please consider applying this series to "net"
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

In firmware assisted GRO flow there could be a single MTU sized
segment arriving due to firmware aggregation timeout/last segment
in an aggregation flow, which is not expected to be an actual gro
packet. So If a skb has zero frags from the GRO flow then simply
push it in the stack as non gso skb.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <yuval.mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Skb's network header needs to be set before extracting IPv4/IPv6
headers from it.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <yuval.mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch handles memory allocation failures for fastpath
gracefully in the driver.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <yuval.mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Martin KaFai Lau says:

====================
tcp: Merge timestamp info when coalescing skbs

This series is separated from the RFC series related to
tcp_sendmsg(MSG_EOR) and it is targeting for the net branch.
This patchset is focusing on fixing cases where TCP
timestamp could be lost after coalescing skbs.

A BPF prog is used to kprobe to sock_queue_err_skb()
and print out the value of serr->ee.ee_data.  The BPF
prog (run-able from bcc) is attached here:

BPF prog used for testing:
~~~~~

from __future__ import print_function
from bcc import BPF

bpf_text = """

int trace_err_skb(struct pt_regs *ctx)
{
	struct sk_buff *skb = (struct sk_buff *)ctx->si;
	struct sock *sk = (struct sock *)ctx->di;
	struct sock_exterr_skb *serr;
	u32 ee_data = 0;

	if (!sk || !skb)
		return 0;

	serr = SKB_EXT_ERR(skb);
	bpf_probe_read(&ee_data, sizeof(ee_data), &serr->ee.ee_data);
	bpf_trace_printk("ee_data:%u\\n", ee_data);

	return 0;
};
"""

b = BPF(text=bpf_text)
b.attach_kprobe(event="sock_queue_err_skb", fn_name="trace_err_skb")
print("Attached to kprobe")
b.trace_print()
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

After receiving sacks, tcp_shifted_skb() will collapse
skbs if possible.  tx_flags and tskey also have to be
merged.

This patch reuses the tcp_skb_collapse_tstamp() to handle
them.

BPF Output Before:
~~~~~
<no-output-due-to-missing-tstamp-event>

BPF Output After:
~~~~~
<...>-2024  [007] d.s.    88.644374: : ee_data:14599

Packetdrill Script:
~~~~~
+0 `sysctl -q -w net.ipv4.tcp_min_tso_segs=10`
+0 `sysctl -q -w net.ipv4.tcp_no_metrics_save=1`
+0 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
+0 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0
+0 bind(3, ..., ...) = 0
+0 listen(3, 1) = 0

0.100 < S 0:0(0) win 32792 <mss 1460,sackOK,nop,nop,nop,wscale 7>
0.100 > S. 0:0(0) ack 1 <mss 1460,nop,nop,sackOK,nop,wscale 7>
0.200 < . 1:1(0) ack 1 win 257
0.200 accept(3, ..., ...) = 4
+0 setsockopt(4, SOL_TCP, TCP_NODELAY, [1], 4) = 0

0.200 write(4, ..., 1460) = 1460
+0 setsockopt(4, SOL_SOCKET, 37, [2688], 4) = 0
0.200 write(4, ..., 13140) = 13140

0.200 > P. 1:1461(1460) ack 1
0.200 > . 1461:8761(7300) ack 1
0.200 > P. 8761:14601(5840) ack 1

0.300 < . 1:1(0) ack 1 win 257 <sack 1461:14601,nop,nop>
0.300 > P. 1:1461(1460) ack 1
0.400 < . 1:1(0) ack 14601 win 257

0.400 close(4) = 0
0.400 > F. 14601:14601(0) ack 1
0.500 < F. 1:1(0) ack 14602 win 257
0.500 > . 14602:14602(0) ack 2
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Tested-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If two skbs are merged/collapsed during retransmission, the current
logic does not merge the tx_flags and tskey.  The end result is
the SCM_TSTAMP_ACK timestamp could be missing for a packet.

The patch:
1. Merge the tx_flags
2. Overwrite the prev_skb's tskey with the next_skb's tskey

BPF Output Before:
~~~~~~
<no-output-due-to-missing-tstamp-event>

BPF Output After:
~~~~~~
packetdrill-2092  [001] d.s.   453.998486: : ee_data:1459

Packetdrill Script:
~~~~~~
+0 `sysctl -q -w net.ipv4.tcp_min_tso_segs=10`
+0 `sysctl -q -w net.ipv4.tcp_no_metrics_save=1`
+0 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
+0 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0
+0 bind(3, ..., ...) = 0
+0 listen(3, 1) = 0

0.100 < S 0:0(0) win 32792 <mss 1460,sackOK,nop,nop,nop,wscale 7>
0.100 > S. 0:0(0) ack 1 <mss 1460,nop,nop,sackOK,nop,wscale 7>
0.200 < . 1:1(0) ack 1 win 257
0.200 accept(3, ..., ...) = 4
+0 setsockopt(4, SOL_TCP, TCP_NODELAY, [1], 4) = 0

0.200 write(4, ..., 730) = 730
+0 setsockopt(4, SOL_SOCKET, 37, [2688], 4) = 0
0.200 write(4, ..., 730) = 730
+0 setsockopt(4, SOL_SOCKET, 37, [2176], 4) = 0
0.200 write(4, ..., 11680) = 11680
+0 setsockopt(4, SOL_SOCKET, 37, [2688], 4) = 0

0.200 > P. 1:731(730) ack 1
0.200 > P. 731:1461(730) ack 1
0.200 > . 1461:8761(7300) ack 1
0.200 > P. 8761:13141(4380) ack 1

0.300 < . 1:1(0) ack 1 win 257 <sack 1461:2921,nop,nop>
0.300 < . 1:1(0) ack 1 win 257 <sack 1461:4381,nop,nop>
0.300 < . 1:1(0) ack 1 win 257 <sack 1461:5841,nop,nop>
0.300 > P. 1:1461(1460) ack 1
0.400 < . 1:1(0) ack 13141 win 257

0.400 close(4) = 0
0.400 > F. 13141:13141(0) ack 1
0.500 < F. 1:1(0) ack 13142 win 257
0.500 > . 13142:13142(0) ack 2
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Tested-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The cpsw_ndo_open() could try to access CPSW registers before
calling pm_runtime_get_sync(). This will trigger L3 error:

 WARNING: CPU: 0 PID: 21 at drivers/bus/omap_l3_noc.c:147 l3_interrupt_handler+0x220/0x34c()
 44000000.ocp:L3 Custom Error: MASTER M2 (64-bit) TARGET L4_FAST (Idle): Data Access in Supervisor mode during Functional access

and CPSW will stop functioning.

Hence, fix it by moving pm_runtime_get_sync() before the first access
to CPSW registers in cpsw_ndo_open().
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>