Increase the retry count for the hard reset function to 100 but
shorten the time out period to 500 ms. See the comment for
ahci_highbank_hardreset for the reasons why those vaulues were
chosen.
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org

The driver's interrupt handling code is too picky in deciding whether it should
handle an interrupt or not which causes completely unneeded spurious interrupts.
Thus make sata_rcar_{ata|serr}_interrupt() *void*; add ATA status register read
to sata_rcar_ata_interrupt() to clear an unexpected ATA interrupt -- it doesn't
get cleared by writing to the SATAINTSTAT register in the interrupt mode we use.

Also, in sata_rcar_ata_interrupt() we should check SATAINTSTAT register only for
enabled interrupts and we should clear  only those interrupts  that we have read
as active first time around, because else we have  a  race and risk clearing  an
interrupt that  can  occur between read  and write of the  SATAINTSTAT  register
and never registering it...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org

A third possible PCI ID, as personally observed, and found in the
pci.ids list.
Signed-off-by: George Spelvin <linux@horizon.com>
Signed-off-by: Tejun Heo <tj@kernel.org>

Iff bmdma_setup() has to stop a DMA transfer before starting a new
one, then the STOP bit in the ATAPI_CONTROL1 register will remain set
(it's only cleared when setting the START bit to 1) and then
bmdma_start() method will set both START and STOP bits simultaneously
which should abort the transfer being just started.  Avoid that by
explicitly clearing the STOP bit in bmdma_start() method (in this case
it will be ignored on write).
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org

libata honors DMADIR for regular commands, but not for internal commands
used (among other) during device initialisation.

This makes SATA-host-to-PATA-device bridges based on Silicon Image SiL3611
(such as "Abit Serillel 2") end up disabled when used with an ATAPI device
after a few tries.

Log output of the bridge being hot-plugged with an ATAPI drive:

  [ 9631.212901] ata1: exception Emask 0x10 SAct 0x0 SErr 0x40c0000 action 0xe frozen
  [ 9631.212913] ata1: irq_stat 0x00000040, connection status changed
  [ 9631.212923] ata1: SError: { CommWake 10B8B DevExch }
  [ 9631.212939] ata1: hard resetting link
  [ 9632.104962] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
  [ 9632.106393] ata1.00: ATAPI: PIONEER DVD-RW  DVR-115, 1.06, max UDMA/33
  [ 9632.106407] ata1.00: applying bridge limits
  [ 9632.108151] ata1.00: configured for UDMA/33
  [ 9637.105303] ata1.00: qc timeout (cmd 0xa0)
  [ 9637.105324] ata1.00: failed to clear UNIT ATTENTION (err_mask=0x5)
  [ 9637.105335] ata1: hard resetting link
  [ 9638.044599] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
  [ 9638.047878] ata1.00: configured for UDMA/33
  [ 9643.044933] ata1.00: qc timeout (cmd 0xa0)
  [ 9643.044953] ata1.00: failed to clear UNIT ATTENTION (err_mask=0x5)
  [ 9643.044963] ata1: limiting SATA link speed to 1.5 Gbps
  [ 9643.044971] ata1.00: limiting speed to UDMA/33:PIO3
  [ 9643.044979] ata1: hard resetting link
  [ 9643.984225] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
  [ 9643.987471] ata1.00: configured for UDMA/33
  [ 9648.984591] ata1.00: qc timeout (cmd 0xa0)
  [ 9648.984612] ata1.00: failed to clear UNIT ATTENTION (err_mask=0x5)
  [ 9648.984619] ata1.00: disabled
  [ 9649.000593] ata1: hard resetting link
  [ 9649.939902] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
  [ 9649.955864] ata1: EH complete

With this patch, the drive enumerates correctly when libata is loaded with
atapi_dmadir=1:

  [ 9891.810863] ata1: exception Emask 0x10 SAct 0x0 SErr 0x40c0000 action 0xe frozen
  [ 9891.810874] ata1: irq_stat 0x00000040, connection status changed
  [ 9891.810884] ata1: SError: { CommWake 10B8B DevExch }
  [ 9891.810900] ata1: hard resetting link
  [ 9892.762105] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
  [ 9892.763544] ata1.00: ATAPI: PIONEER DVD-RW  DVR-115, 1.06, max UDMA/33, DMADIR
  [ 9892.763558] ata1.00: applying bridge limits
  [ 9892.765393] ata1.00: configured for UDMA/33
  [ 9892.786063] ata1: EH complete
  [ 9892.792062] scsi 0:0:0:0: CD-ROM            PIONEER  DVD-RW  DVR-115  1.06 PQ: 0 ANSI: 5
  [ 9892.798455] sr2: scsi3-mmc drive: 12x/12x writer dvd-ram cd/rw xa/form2 cdda tray
  [ 9892.798837] sr 0:0:0:0: Attached scsi CD-ROM sr2
  [ 9892.799109] sr 0:0:0:0: Attached scsi generic sg6 type 5

Based on a patch by Csaba Halász <csaba.halasz@gmail.com> on linux-ide:
http://marc.info/?l=linux-ide&m=136121147832295&w=2

tj: minor formatting changes.
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org

Adds IDE-mode SATA Device IDs for the Intel BayTrail platform.
Signed-off-by: Chew, Chiau Ee <chiau.ee.chew@intel.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org

Jeff moved on to a greener pasture.

 s/Maintained by: Jeff Garzik/Maintained by: Tejun Heo/g
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jeff Garzik <jgarzik@pobox.com>

Pull tracing/kprobes update from Steven Rostedt:
 "The majority of these changes are from Masami Hiramatsu bringing
  kprobes up to par with the latest changes to ftrace (multi buffering
  and the new function probes).

  He also discovered and fixed some bugs in doing so.  When pulling in
  his patches, I also found a few minor bugs as well and fixed them.

  This also includes a compile fix for some archs that select the ring
  buffer but not tracing.

  I based this off of the last patch you took from me that fixed the
  merge conflict error, as that was the commit that had all the changes
  I needed for this set of changes."

* tag 'trace-fixes-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing/kprobes: Support soft-mode disabling
  tracing/kprobes: Support ftrace_event_file base multibuffer
  tracing/kprobes: Pass trace_probe directly from dispatcher
  tracing/kprobes: Increment probe hit-count even if it is used by perf
  tracing/kprobes: Use bool for retprobe checker
  ftrace: Fix function probe when more than one probe is added
  ftrace: Fix the output of enabled_functions debug file
  ftrace: Fix locking in register_ftrace_function_probe()
  tracing: Add helper function trace_create_new_event() to remove duplicate code
  tracing: Modify soft-mode only if there's no other referrer
  tracing: Indicate enabled soft-mode in enable file
  tracing/kprobes: Fix to increment return event probe hit-count
  ftrace: Cleanup regex_lock and ftrace_lock around hash updating
  ftrace, kprobes: Fix a deadlock on ftrace_regex_lock
  ftrace: Have ftrace_regex_write() return either read or error
  tracing: Return error if register_ftrace_function_probe() fails for event_enable_func()
  tracing: Don't succeed if event_enable_func did not register anything
  ring-buffer: Select IRQ_WORK

Merge tag 'stable/for-linus-3.10-rc0-tag-two' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen

Pull Xen bug-fixes from Konrad Rzeszutek Wilk:
 - More fixes in the vCPU PVHVM hotplug path.
 - Add more documentation.
 - Fix various ARM related issues in the Xen generic drivers.
 - Updates in the xen-pciback driver per Bjorn's updates.
 - Mask the x2APIC feature for PV guests.

* tag 'stable/for-linus-3.10-rc0-tag-two' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
  xen/pci: Used cached MSI-X capability offset
  xen/pci: Use PCI_MSIX_TABLE_BIR, not PCI_MSIX_FLAGS_BIRMASK
  xen: clear IRQ_NOAUTOEN and IRQ_NOREQUEST
  xen: mask x2APIC feature in PV
  xen: SWIOTLB is only used on x86
  xen/spinlock: Fix check from greater than to be also be greater or equal to.
  xen/smp/pvhvm: Don't point per_cpu(xen_vpcu, 33 and larger) to shared_info
  xen/vcpu: Document the xen_vcpu_info and xen_vcpu
  xen/vcpu/pvhvm: Fix vcpu hotplugging hanging.

Pull second SCSI update from James "Jaj B" Bottomley:
 "This is the final round of SCSI patches for the merge window.  It
  consists mostly of driver updates (bnx2fc, ibmfc, fnic, lpfc,
  be2iscsi, pm80xx, qla4x and ipr).

  There's also the power management updates that complete the patches in
  Jens' tree, an iscsi refcounting problem fix from the last pull, some
  dif handling in scsi_debug fixes, a few nice code cleanups and an
  error handling busy bug fix."

* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (92 commits)
  [SCSI] qla2xxx: Update firmware link in Kconfig file.
  [SCSI] iscsi class, qla4xxx: fix sess/conn refcounting when find fns are used
  [SCSI] sas: unify the pointlessly separated enums sas_dev_type and sas_device_type
  [SCSI] pm80xx: thermal, sas controller config and error handling update
  [SCSI] pm80xx: NCQ error handling changes
  [SCSI] pm80xx: WWN Modification for PM8081/88/89 controllers
  [SCSI] pm80xx: Changed module name and debug messages update
  [SCSI] pm80xx: Firmware flash memory free fix, with addition of new memory region for it
  [SCSI] pm80xx: SPC new firmware changes for device id 0x8081 alone
  [SCSI] pm80xx: Added SPCv/ve specific hardware functionalities and relevant changes in common files
  [SCSI] pm80xx: MSI-X implementation for using 64 interrupts
  [SCSI] pm80xx: Updated common functions common for SPC and SPCv/ve
  [SCSI] pm80xx: Multiple inbound/outbound queue configuration
  [SCSI] pm80xx: Added SPCv/ve specific ids, variables and modify for SPC
  [SCSI] lpfc: fix up Kconfig dependencies
  [SCSI] Handle MLQUEUE busy response in scsi_send_eh_cmnd
  [SCSI] sd: change to auto suspend mode
  [SCSI] sd: use REQ_PM in sd's runtime suspend operation
  [SCSI] qla4xxx: Fix iocb_cnt calculation in qla4xxx_send_mbox_iocb()
  [SCSI] ufs: Correct the expected data transfersize
  ...

Pull idle update from Len Brown:
 "Add support for new Haswell-ULT CPU idle power states"

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
  intel_idle: initial C8, C9, C10 support
  tools/power turbostat: display C8, C9, C10 residency

Pull audit changes from Eric Paris:
 "Al used to send pull requests every couple of years but he told me to
  just start pushing them to you directly.

  Our touching outside of core audit code is pretty straight forward.  A
  couple of interface changes which hit net/.  A simple argument bug
  calling audit functions in namei.c and the removal of some assembly
  branch prediction code on ppc"

* git://git.infradead.org/users/eparis/audit: (31 commits)
  audit: fix message spacing printing auid
  Revert "audit: move kaudit thread start from auditd registration to kaudit init"
  audit: vfs: fix audit_inode call in O_CREAT case of do_last
  audit: Make testing for a valid loginuid explicit.
  audit: fix event coverage of AUDIT_ANOM_LINK
  audit: use spin_lock in audit_receive_msg to process tty logging
  audit: do not needlessly take a lock in tty_audit_exit
  audit: do not needlessly take a spinlock in copy_signal
  audit: add an option to control logging of passwords with pam_tty_audit
  audit: use spin_lock_irqsave/restore in audit tty code
  helper for some session id stuff
  audit: use a consistent audit helper to log lsm information
  audit: push loginuid and sessionid processing down
  audit: stop pushing loginid, uid, sessionid as arguments
  audit: remove the old depricated kernel interface
  audit: make validity checking generic
  audit: allow checking the type of audit message in the user filter
  audit: fix build break when AUDIT_DEBUG == 2
  audit: remove duplicate export of audit_enabled
  Audit: do not print error when LSMs disabled
  ...

Pull nfsd fixes from Bruce Fields:
 "Small fixes for two bugs and two warnings"

* 'for-3.10' of git://linux-nfs.org/~bfields/linux:
  nfsd: fix oops when legacy_recdir_name_error is passed a -ENOENT error
  SUNRPC: fix decoding of optional gss-proxy xdr fields
  SUNRPC: Refactor gssx_dec_option_array() to kill uninitialized warning
  nfsd4: don't allow owner override on 4.1 CLAIM_FH opens

Pull x86 platform drivers from Matthew Garrett:
 "Small set of updates, mainly trivial bugfixes and some small updates
  to deal with newer hardware.

  There's also a new driver that allows qemu guests to notify the
  hypervisor that they've just paniced, which seems useful."

* 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86:
  Add support for fan button on Ideapad Z580
  pvpanic: pvpanic device driver
  asus-nb-wmi: set wapf=4 for ASUSTeK COMPUTER INC. X75A
  drivers: platform: x86: Use PTR_RET function
  sony-laptop: SVS151290S kbd backlight and gfx switch support
  hp-wmi: add more definitions for new event_id's
  dell-laptop: Fix krealloc() misuse in parse_da_table()
  hp_accel: Ignore the error from lis3lv02d_poweron() at resume
  dell: add new dell WMI format for the AIO machines

Pull stray syscall bits from Al Viro:
 "Several syscall-related commits that were missing from the original"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
  switch compat_sys_sysctl to COMPAT_SYSCALL_DEFINE
  unicore32: just use mmap_pgoff()...
  unify compat fanotify_mark(2), switch to COMPAT_SYSCALL_DEFINE
  x86, vm86: fix VM86 syscalls: use SYSCALL_DEFINEx(...)

Merge tag 'ecryptfs-3.10-rc1-ablkcipher' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs

Pull eCryptfs update from Tyler Hicks:
 "Improve performance when AES-NI (and most likely other crypto
  accelerators) is available by moving to the ablkcipher crypto API.
  The improvement is more apparent on faster storage devices.

  There's no noticeable change when hardware crypto is not available"

* tag 'ecryptfs-3.10-rc1-ablkcipher' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
  eCryptfs: Use the ablkcipher crypto API

Pull misc fixes from David Woodhouse:
 "This is some miscellaneous cleanups that don't really belong anywhere
  else (or were ignored), that have been sitting in linux-next for some
  time.  Two of them are fixes resulting from my audit of krealloc()
  usage that don't seem to have elicited any response when I posted
  them, and the other three are patches from Artem removing dead code."

* tag 'for-linus-20130509' of git://git.infradead.org/~dwmw2/random-2.6:
  pcmcia: remove RPX board stuff
  m68k: remove rpxlite stuff
  pcmcia: remove Motorola MBX860 support
  params: Fix potential memory leak in add_sysfs_param()
  dell-laptop: Fix krealloc() misuse in parse_da_table()

Pull kvm fixes from Gleb Natapov:
 "Most of the fixes are in the emulator since now we emulate more than
  we did before for correctness sake we see more bugs there, but there
  is also an OOPS fixed and corruption of xcr0 register."

* tag 'kvm-3.10-2' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: emulator: emulate SALC
  KVM: emulator: emulate XLAT
  KVM: emulator: emulate AAM
  KVM: VMX: fix halt emulation while emulating invalid guest sate
  KVM: Fix kvm_irqfd_init initialization
  KVM: x86: fix maintenance of guest/host xcr0 state

Pull device-mapper updates from Alasdair Kergon:
 "Allow devices that hold metadata for the device-mapper thin
  provisioning target to be extended easily; allow WRITE SAME on
  multipath devices; an assortment of little fixes and clean-ups."

* tag 'dm-3.10-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm: (21 commits)
  dm cache: set config value
  dm cache: move config fns
  dm thin: generate event when metadata threshold passed
  dm persistent metadata: add space map threshold callback
  dm persistent data: add threshold callback to space map
  dm thin: detect metadata device resizing
  dm persistent data: support space map resizing
  dm thin: open dev read only when possible
  dm thin: refactor data dev resize
  dm cache: replace memcpy with struct assignment
  dm cache: fix typos in comments
  dm cache policy: fix description of lookup fn
  dm: document iterate_devices
  dm persistent data: fix error message typos
  dm cache: tune migration throttling
  dm mpath: enable WRITE SAME support
  dm table: fix write same support
  dm bufio: avoid a possible __vmalloc deadlock
  dm snapshot: fix error return code in snapshot_ctr
  dm cache: fix error return code in cache_create
  ...

Pull HID fixes from Jiri Kosina:

 - fix usage of sleeping lock in atomic context from Jiri Kosina

 - build fix for hid-steelseries under certain .config setups by Simon Wood

 - simple mismerge fix from Fernando Luis Vázquez Cao

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  HID: debug: fix RCU preemption issue
  HID: hid-steelseries fix led class build issue
  HID: reintroduce fix-up for certain Sony RF receivers

Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Pull sound fixes from Takashi Iwai:
 "This contains small fixes since the previous pull request:

   - A few regression fixes and small updates of HD-audio

   - Yet another fix for Haswell HDMI audio

   - A copule of trivial fixes in ASoC McASP, DPAM and WM8994"

* tag 'sound-3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  Revert "ALSA: hda - Don't set up active streams twice"
  ALSA: Add comment for control TLV API
  ALSA: hda - Apply pin-enablement workaround to all Haswell HDMI codecs
  ALSA: HDA: Fix Oops caused by dereference NULL pointer
  ALSA: mips/sgio2audio: Remove redundant platform_set_drvdata()
  ALSA: mips/hal2: Remove redundant platform_set_drvdata()
  ALSA: hda - Fix 3.9 regression of EAPD init on Conexant codecs
  sound: Fix make allmodconfig on MIPS
  ALSA: hda - Fix system panic when DMA > 40 bits for Nvidia audio controllers
  ALSA: atmel: Remove redundant platform_set_drvdata()
  ASoC: McASP: Fix receive clock polarity in DAIFMT_NB_NF mode.
  ASoC: wm8994: missing break in wm8994_aif3_hw_params()
  ASoC: McASP: Add pins output direction for rx clocks when configured in CBS_CFS format
  ASoC: dapm: use clk_prepare_enable and clk_disable_unprepare

Pull MIPS updates from Ralf Baechle:

 - More work on DT support for various platforms

 - Various fixes that were to late to make it straight into 3.9

 - Improved platform support, in particular the Netlogic XLR and
   BCM63xx, and the SEAD3 and Malta eval boards.

 - Support for several Ralink SOC families.

 - Complete support for the microMIPS ASE which basically reencodes the
   existing MIPS32/MIPS64 ISA to use non-constant size instructions.

 - Some fallout from LTO work which remove old cruft and will generally
   make the MIPS kernel easier to maintain and resistant to compiler
   optimization, even in absence of LTO.

 - KVM support.  While MIPS has announced hardware virtualization
   extensions this KVM extension uses trap and emulate mode for
   virtualization of MIPS32.  More KVM work to add support for VZ
   hardware virtualizaiton extensions and MIPS64 will probably already
   be merged for 3.11.

Most of this has been sitting in -next for a long time.  All defconfigs
have been build or run time tested except three for which fixes are being
sent by other maintainers.

Semantic conflict with kvm updates done as per Ralf

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (118 commits)
  MIPS: Add new GIC clockevent driver.
  MIPS: Formatting clean-ups for clocksources.
  MIPS: Refactor GIC clocksource code.
  MIPS: Move 'gic_frequency' to common location.
  MIPS: Move 'gic_present' to common location.
  MIPS: MIPS16e: Add unaligned access support.
  MIPS: MIPS16e: Support handling of delay slots.
  MIPS: MIPS16e: Add instruction formats.
  MIPS: microMIPS: Optimise 'strnlen' core library function.
  MIPS: microMIPS: Optimise 'strlen' core library function.
  MIPS: microMIPS: Optimise 'strncpy' core library function.
  MIPS: microMIPS: Optimise 'memset' core library function.
  MIPS: microMIPS: Add configuration option for microMIPS kernel.
  MIPS: microMIPS: Disable LL/SC and fix linker bug.
  MIPS: microMIPS: Add vdso support.
  MIPS: microMIPS: Add unaligned access support.
  MIPS: microMIPS: Support handling of delay slots.
  MIPS: microMIPS: Add support for exception handling.
  MIPS: microMIPS: Floating point support.
  MIPS: microMIPS: Fix macro naming in micro-assembler.
  ...

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

This fixes a bug where the iscsi class/driver did not do a put_device
when a sess/conn device was found. This also simplifies the interface
by not having to pass in some arguments that were duplicated and did
not need to be exported.
Reported-by: Zhao Hongjiang <zhaohongjiang@huawei.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

These enums have been separate since the dawn of SAS, mainly because the
latter is a procotol only enum and the former includes additional state
for libsas.  The dichotomy causes endless confusion about which one you
should use where and leads to pointless warnings like this:

drivers/scsi/mvsas/mv_sas.c: In function 'mvs_update_phyinfo':
drivers/scsi/mvsas/mv_sas.c:1162:34: warning: comparison between 'enum sas_device_type' and 'enum sas_dev_type' [-Wenum-compare]

Fix by eliminating one of them.  The one kept is effectively the sas.h
one, but call it sas_device_type and make sure the enums are all
properly namespaced with the SAS_ prefix.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Modified thermal configuration to happen after interrupt registration
Added SAS controller configuration during initialization
Added error handling logic to handle I_T_Nexus errors and variants

[jejb: fix up tabs and spaces issues]
Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Handled NCQ errors in the low level driver as the FW
is not providing the faulty tag for NCQ errors for libsas
to recover.

[jejb: fix checkpatch issues]
Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Individual WWN read operations based on controller.
PM8081 - Read WWN from Flash VPD.
PM8088/89 - Read WWN from EEPROM.
PM8001 - Read WWN from NVM.
Signed-off-by: Sakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com>
Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Changed name in driver to pm80xx. Updated debug messages.
Signed-off-by: Sakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com>
Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Performing pci_free_consistent in tasklet had result in a core dump. So
allocated a new memory region for it. Fix for passing proper address
and operation in firmware flash update.
Signed-off-by: Sakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com>
Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Additional bar shift for new SPC firmware, applicable to device
id 0x8081 only.
Signed-off-by: Sakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com>
Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Implementation of SPCv/ve specific hardware functionality and
macros. Changing common functionalities wrt SPCv/ve operations.
Conditional checks for SPC specific operations.
Signed-off-by: Sakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com>
Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Implementation of interrupt handlers and tasklets to support
upto 64 interrupt for the device.
Signed-off-by: Sakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com>
Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Update of function prototype for common function to SPC and SPCv/ve.
Multiple queues implementation for IO.
Signed-off-by: Sakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com>
Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Memory allocation and configuration of multiple inbound and
outbound queues.
Signed-off-by: Sakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com>
Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Updated pci id table with device, vendor, subdevice and subvendor ids
for 8081, 8088, 8089 SAS/SATA controllers. Added SPCv/ve related macros.
Updated macros, hba info structure and other structures for SPCv/ve.
Update of structure and variable names for SPC hardware functionalities.
Signed-off-by: Sakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com>
Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

lpfc uses the generic checksum as well as the T10DIF one from the lib/
directory, so make sure they're selected.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>