- 12 Jan, 2014 1 commit
-
-
Mauro Carvalho Chehab authored
Follow the error codes for I2C as described at Documentation/i2c/fault-codes. In the case of the I2C status register (0x05), this is mapped into: - ENXIO - when reg 05 returns 0x10 - ETIMEDOUT - when the device is not temporarily not responding (e. g. reg 05 returning something not 0x10 or 0x00) - EIO - for generic I/O errors that don't fit into the above. In the specific case of 0-byte reads, used only during I2C device probing, it keeps returning -ENODEV. TODO: return EBUSY when reg 05 returns 0x20 on em2874 and upper. Signed-off-by:Mauro Carvalho Chehab <m.chehab@samsung.com>
-
- 10 Jan, 2014 8 commits
-
-
Mauro Carvalho Chehab authored
In the lack of a better spec, let's assume the timeout values compatible with SMBus spec: http://smbus.org/specs/smbus110.pdf at chapter 8 - Electrical Characteristics of SMBus devices Ok, SMBus is a subset of I2C, and not all devices will be following it, but the timeout value before this patch was not even following the spec. So, while we don't have a better guess for it, use 35 + 1 ms as the timeout. Signed-off-by:
-
Mauro Carvalho Chehab authored
This macro is used by all em28xx devices, and not just em2800. Reviewed-by:
Frank Schäfer <fschaefer.oss@googlemail.com> Signed-off-by:
-
Mauro Carvalho Chehab authored
The I2C wait completion/timeout logic currently assumes that msleep(5) will wait exaclty 5 ms. This is not true at all, as it depends on CONFIG_HZ. Convert it to use jiffies, in order to not wait for more time than needed. Signed-off-by: -
Mauro Carvalho Chehab authored
Instead of assuming that msleep() is precise, use a jiffies based code to wait for AC97 to be available. Reviewed-by:
-
Mauro Carvalho Chehab authored
That removes those timeout errors: [ 3675.930940] xc2028 19-0061: Device is Xceive 3028 version 1.0, firmware version 2.7 [ 3676.060487] xc2028 19-0061: divisor= 00 00 8d d0 (freq=567.250) [ 3676.349449] xc2028 19-0061: Putting xc2028/3028 into poweroff mode. [ 3698.247645] xc2028 19-0061: xc2028_get_reg 0002 called [ 3698.253276] em2860 #0: I2C transfer timeout on writing to addr 0xc2 [ 3698.253301] xc2028 19-0061: i2c input error: rc = -121 (should be 2) [ 3698.253327] xc2028 19-0061: xc2028_signal called [ 3698.253339] xc2028 19-0061: xc2028_get_reg 0002 called [ 3698.259283] em2860 #0: I2C transfer timeout on writing to addr 0xc2 [ 3698.259312] xc2028 19-0061: i2c input error: rc = -121 (should be 2) Signed-off-by: -
Mauro Carvalho Chehab authored
Only send a power down command for the device if it is not already in power down state. That prevents a timeout when trying to talk with the device. Signed-off-by: -
Mauro Carvalho Chehab authored
Instead of allocating/deallocating URBs and transfer buffers every time stream is started/stopped, just do it once. That reduces the memory allocation pressure and makes the code that start/stop streaming a way simpler. Signed-off-by:
Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by:
-
Mauro Carvalho Chehab authored
Instead of allocating transfer buffers with kmalloc() use usb_alloc_coherent(). This patch should make it work also with ARM CPUs. Reviewed-by:
-
- 07 Jan, 2014 31 commits
-
-
Links (Markus) authored
Add a new USB ID to the driver. Signed-off-by:
Links (Markus) <help.markus+git@gmail.com> Signed-off-by:
-
Laurent Pinchart authored
The comment incorrectly explains that the code verifies information provided by userspace, while verification has been performed earlier in reality. Fix it. Signed-off-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
-
Malcolm Priestley authored
Value of fec is achieved by the upper nibble bits 6,7 & 8. Signed-off-by:
Malcolm Priestley <tvboxspy@gmail.com> Signed-off-by:
-
Malcolm Priestley authored
Register 0x70 is used to set fec, register 0x76 is used to get fec Register 0x76 is set to 0x8. Signed-off-by:
-
Malcolm Priestley authored
The correct lock values is when bits of the value 0xee are set. Signed-off-by:
-
Malcolm Priestley authored
Current setting of symbol rate is not very actuate causing loss of lock. Covert temp to u64 and use mclk to calculate from big number. Calculate symbol rate by dividing symbol rate by 1000 times 1 << 24 and dividing sum by mclk. Add other symbol rate settings to function registers 0xa0-0xa3. In set_frontend add changes to register 0xf1 this must be done prior call to fe_reset. Register 0x00 doesn't need a second write of 0x1 Applied after patch m88rs2000: add m88rs2000_set_carrieroffset Signed-off-by:
-
Malcolm Priestley authored
Set the carrier offset correctly using the default mclk values. Add function m88rs2000_get_mclk to calculate the mclk value against crystal frequency which will later be used for other functions. Add function m88rs2000_set_carrieroffset to calculate and set the offset value. variable offset becomes a signed value. Register 0x86 is set the appropriate value according to remainder value of frequency % 192857 calculation as shown. Signed-off-by:
-
Julia Lawall authored
Set the return variable to an error code as done elsewhere in the function. A simplified version of the semantic match that finds this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> ( if@p1 (\(ret < 0\|ret != 0\)) { ... return ret; } | ret@p1 = 0 ) ... when != ret = e1 when != &ret *if(...) { ... when != ret = e2 when forall return ret; } // </smpl> Signed-off-by:
Julia Lawall <Julia.Lawall@lip6.fr> Cc: Antti Palosaari <crope@iki.fi> Signed-off-by:
-
Julia Lawall authored
The rest of the function uses ret to store the return value, even setting ret to i a few lines before this, so return ret instead of i. A simplified version of the semantic match that finds this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> ( if@p1 (\(ret < 0\|ret != 0\)) { ... return ret; } | ret@p1 = 0 ) ... when != ret = e1 when != &ret *if(...) { ... when != ret = e2 when forall return ret; } // </smpl> Signed-off-by:
-
Alexey Khoroshilov authored
Failure handling is incomplete in as102_usb_probe(). The patch implements proper resource deallocations. Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by:
Alexey Khoroshilov <khoroshilov@ispras.ru> Signed-off-by:
-
Hans Verkuil authored
This driver should only build if MEDIA_USB_SUPPORT is set. Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Reported-by:
Jim Davis <jim.epost@gmail.com> Reported-by:
kbuild test robot <fengguang.wu@intel.com> Signed-off-by:
-
Sachin Kamat authored
Dereference 'fw' after the NULL check. Signed-off-by:
Sachin Kamat <sachin.kamat@linaro.org> Signed-off-by:
-
Sachin Kamat authored
Fixes the following error: ERROR: return is not a function, parentheses are not required FILE: drivers/media/i2c/s5k5baf.c:1353: Signed-off-by:
-
Sachin Kamat authored
Fixes the following warnings: drivers/media/i2c/s5k5baf.c: In function 's5k5baf_fw_parse': drivers/media/i2c/s5k5baf.c:362:3: warning: format '%d' expects argument of type 'int', but argument 3 has type 'size_t' [-Wformat=] drivers/media/i2c/s5k5baf.c:383:4: warning: format '%d' expects argument of type 'int', but argument 4 has type 'size_t' [-Wformat=] Signed-off-by:
-
Matthias Schwarzott authored
Fix continuation lines. [m.chehab@samsung.com: This was actually part of a v2 patch meant to fix i2c debug prints. As version 1 was already applied, I'm applying here the diff and fixing the patch subject/description] Signed-off-by:
Matthias Schwarzott <zzam@gentoo.org> Signed-off-by:
-
Frank Schaefer authored
The audio configuration in chip config register 0x00 and eeprom are always consistent. But currently the audio configuration #defines for the chip config register say 0x20 means 3 sample rates and 0x30 5 sample rates, while the eeprom info output says 0x20 means 1 sample rate and 0x30 3 sample rates. I've checked the datasheet excerpts I have and it seems that the meaning of these bits is different for em2820/40 (1 and 3 sample rates) and em2860+ (3 and 5 smaple rates). I have also checked my Hauppauge WinTV USB 2 (em2840) and the chip/eeprom audio config 0x20 matches the sample rates reproted by the USB device descriptor (32k only). Signed-off-by:
-
Valentine Barshak authored
This adds R-Car M2 (R8A7791) VIN support. Both H2 and M2 variants look the same from the driver's point of view, so use GEN2 id for both. Signed-off-by:
Valentine Barshak <valentine.barshak@cogentembedded.com> Acked-by:
Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by:
-
Laurent Pinchart authored
Under abnormal conditions (such as glitches on the HSYNC/VSYNC signals) the CCDC output SBL can fail to become idle. The driver currently logs this condition to the kernel log and doesn't restart the CCDC. This results in CCDC video capture hanging without any notification to userspace. Cancel the pipeline and mark the CCDC as crashed instead of hanging. Userspace will be notified of the problem and will then be able to close and reopen the device to trigger a reset of the ISP. Signed-off-by:
Sakari Ailus <sakari.ailus@iki.fi> Signed-off-by:
-
Laurent Pinchart authored
Modules failing to stop are fatal errors for the preview engine only. Flag that condition separately from the other stop failures to prepare support for more fatal errors. Signed-off-by:
-
Laurent Pinchart authored
When a fatal error that prevents any further video streaming occurs in a pipeline, all queued buffers must be marked as erroneous and new buffers must be prevented from being queued. Implement this behaviour with a new omap3isp_pipeline_cancel_stream() function that can be used by submodules to cancel streaming. Signed-off-by:
-
Mauro Carvalho Chehab authored
As reported by the kbuild test robot: All error/warnings: >> ERROR: "em28xx_release_resources" [drivers/media/usb/em28xx/em28xx-v4l.ko] undefined! Reported-by:
-
Hans Verkuil authored
The include for delay.h was missing. Signed-off-by:
-
Ricardo Ribalda authored
As discussed on the media summit 2013, there is no reason for the width and height to be signed. Therefore this patch is an attempt to convert those fields from __s32 to __u32. Signed-off-by:
Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Acked-by: Sakari Ailus <sakari.ailus@iki.fi> (documentation and smiapp) Acked-by:
Lad, Prabhakar <prabhakar.csengg@gmail.com> Signed-off-by:
-
Joe Perches authored
Emitting an OOM message isn't necessary after input_allocate_device as there's a generic OOM and a dump_stack already done. Signed-off-by:
Joe Perches <joe@perches.com> Signed-off-by:
-
Fengguang Wu authored
drivers/staging/media/bcm2048/radio-bcm2048.c:2255:3-4: Unneeded semicolon Removes unneeded semicolon. Generated by: coccinelle/misc/semicolon.cocci CC: Hans Verkuil <hans.verkuil@cisco.com> CC: Mauro Carvalho Chehab <m.chehab@samsung.com> Signed-off-by:
-
Fengguang Wu authored
drivers/staging/media/bcm2048/radio-bcm2048.c:2632:1-7: Replace memcpy with struct assignment /c/kernel-tests/src/cocci/drivers/staging/media/bcm2048/radio-bcm2048.c:744:1-7: Replace memcpy with struct assignment /c/kernel-tests/src/cocci/drivers/staging/media/bcm2048/radio-bcm2048.c:2360:3-9: Replace memcpy with struct assignment Generated by: coccinelle/misc/memcpy-assign.cocci CC: Hans Verkuil <hans.verkuil@cisco.com> CC: Mauro Carvalho Chehab <m.chehab@samsung.com> Signed-off-by:
-
Hans Verkuil authored
You can set this through sysfs, so don't mix the two. Signed-off-by:
-
Hans Verkuil authored
saa6588 always blocked while waiting for data, even if the filehandle was in non-blocking mode. Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
CMD_CLOSE sets data_available_for_read to 1, which is necessary to do the wakeup call, but it is never reset to 0. Because of this calling CMD_POLL afterwards will always return that data is available, even if there isn't any. Signed-off-by:
-
Hans Verkuil authored
There are no controls for the radio node, so just drop support for this ioctl. Signed-off-by:
-
