- 21 Oct, 2013 8 commits
-
-
Kalle Valo authored
ath10k_pci_wait() didn't notify any errors to callers, it just printed a warning so add proper error handling. This fixes a crash Ben reported: ath10k: MSI-X interrupt handling (8 intrs) ath10k: Unable to wakeup target ath10k: target took longer 5000 us to wake up (awake count 1) ath10k: Failed to get pcie state addr: -16 ath10k: early firmware event indicated BUG: unable to handle kernel NULL pointer dereference at 0000000000000004 IP: [<ffffffffa06ae46c>] ath10k_ce_completed_send_next+0x47/0x122 [ath10k_pci] Reported-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
-
Michal Kazior authored
10.1.389 firmware has some differences in calculation of number of outstanding HTT TX completions. This led to FW crashes of 10.1.389 while main firmware branch was unnaffected. The patch makes sure ath10k doesn't queue up more MSDUs than it should. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
-
Kalle Valo authored
To make it easier to access SOC registers. No functional changes. Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
-
Michal Kazior authored
If firmware crashes during FW probing it would try to perform FW recovery which uses mac80211 workqueue before registering to mac80211. Using internal workqueue solves the problem. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
-
Michal Kazior authored
NSTS values reported in the VHT-SIG-A1 are 0 through 7 but they actually describe number of streams 1 through 8. 1SS frames were dropped. This patch fixes this. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
-
Michal Kazior authored
This fixes incorrect values being printed on big-endian hosts. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
-
Michal Kazior authored
Add a few checks and warnings to make it easier to track any kind of monitor vdev mismanagement. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
-
Michal Kazior authored
This fixes issue with interface bridging. Linux bridging sets promiscuous mode for all interfaces that are in a bridge. This translates to configure_filter() being called in a mac80211 driver. Before the patch operational interface would be started and upped again when promiscuous mode was enabled causing all sorts of strange issues: * no HTT RX happening (i.e. no traffic) * FW crash upon driver reload/unload Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
-
- 18 Oct, 2013 32 commits
-
-
Gabor Juhos authored
Use the module_pci_driver() macro to make the code simpler by eliminating module_init and module_exit calls. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Gabor Juhos authored
The PCI and SoC specific drivers are using separate code now so it is not reasonable to use the same module for both drivers anymore. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Gabor Juhos authored
The 'rt2800pci_hwcrypt_disabled' function is the only PCI specific callback which is used by the SoC driver. Create a clone of that to get rid of the dependency. Even though the two functions are using the same variable, but the SoC specific code will be moved into a separate module which will have its own 'modparam_nohwcrypt' variable. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Gabor Juhos authored
Move the function into the rt2800mmio module, in order to make it usable from other modules. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Gabor Juhos authored
The function is called for PCI and SoC devices however the MCU related part of the function has no effect on SoC devices. Move the common part of the function into a separate helper and use that for the SoC devices. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Gabor Juhos authored
The function contain code for SoC devices only. Rename the function to 'rt2800soc_disable_radio' and move it to the SoC specific section. Use the renamed function in the SoC specific code only and remove the 'if rt2x00_is_soc(rt2x00dev)' condition from the function body. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Gabor Juhos authored
The 'rt2800pci_set_state' function uses MCU commands to set the device state, however these have no effect on SoC devices. Use a different set_state callback which does not use the MCU fcuntions. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Gabor Juhos authored
Use empty firmware callbacks for SoC devices because those don't require firmware. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Gabor Juhos authored
Rename the 'rt2800pci_read_eeprom_soc function' to 'rt2800soc_read_eeprom' and use that directly in the SoC specific 'rt2800_ops' structure. Also move the 'rt2800pci_eeprom_read' function into an 'ifdef PCI' section and remove the 'rt2800pci_read_eeprom_soc' call from that. Additionally, remove the dummy inline eeprom functions. Those are not used anymore. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Gabor Juhos authored
This makes it possible to use different callback functions for PCI and SoC devices which will allow to move the SoC driver into a separate module. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Gabor Juhos authored
Move the functions into a separate module, in order to make those usable from other modules. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Gabor Juhos authored
The functions are used for devices with memory mapped I/O and contain no PCI specific code at all. Use rt2800mmio prefix instead of rt2800pci in the function names to reflect that. The patch contains no functional changes. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Gabor Juhos authored
Move the functions into a separate module, in order to make those usable from other modules. Also move the queue register offset macros from rt2800pci.h into rt2800mmio.h. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Gabor Juhos authored
The functions are used for devices with memory mapped I/O and contain no PCI specific code at all. Use rt2800mmio prefix instead of rt2800pci in the function names to reflect that. The patch contains no functional changes. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Gabor Juhos authored
Move the functions into a separate module, in order to make those usable from other modules. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Gabor Juhos authored
The functions are used for devices with memory mapped I/O and contain no PCI specific code at all. Use rt2800mmio prefix instead of rt2800pci in the function names to reflect that. The patch contains no functional changes. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Gabor Juhos authored
Move the functions into a separate module, in order to make those usable from other modules. Also move the RX descriptor related defines from rt2800pci.h into rt2800mmio.h Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Gabor Juhos authored
The functions are used for devices with memory mapped I/O and contain no PCI specific code at all. Use rt2800mmio prefix instead of rt2800pci in the function names to reflect that. The patch contains no functional changes. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Gabor Juhos authored
Move the functions into a separate module, in order to make those usable from other modules. Also move the TX descriptor related defines from rt2800pci.h into rt2800mmio.h. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Gabor Juhos authored
The functions are used for devices with memory mapped I/O and contain no PCI specific code at all. Use rt2800mmio prefix instead of rt2800pci in the function names to reflect that. The patch contains no functional changes. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Gabor Juhos authored
Create a new module for common code which can be used for rt2800 device with memory mapped I/O. It is an empty module for now, but it will be populated by subsequent patches. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felipe Pena authored
There is a typo where the checking for priv->ReAssociationRequestRetryCnt must be, it was checking for priv->AssociationRequestRetryCnt instead. Signed-off-by: Felipe Pena <felipensp@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Arend van Spriel authored
If the SDIO host controller does not support scatter-gather the glom superframe must be transfered from the device and the data for each packet in the queue must be extracted from it. Reviewed-by: Franky Lin <frankyl@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Arend van Spriel authored
When running on a host controller that does not support scatter-gather transfers the function brcmf_sdio_txpkt_prep() should not add tail padding buffers. Reviewed-by: Franky Lin <frankyl@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Arend van Spriel authored
If the host does not support scatter-gather transmit the packets in the pktq individually using brcmf_sdio_buffrw(). Reviewed-by: Franky Lin <frankyl@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Arend van Spriel authored
The function brcmf_sdcard_recv_chain() has been reworked with commit "brcmfmac: add sdio sg list support", but the incr_fix variable is only assigned but not used so removing it now. Reviewed-by: Franky Lin <frankyl@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Arend van Spriel authored
Not all calls to the function brcmf_sdio_addrprep() check the return value, but it may fail so better verify it. Reviewed-by: Franky Lin <frankyl@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Arend van Spriel authored
The function brcmf_sdio_sglist_rw() does a different code path when packet queue length is 1. Move this to a separate function reducing overhead in the calling context. Reviewed-by: Franky Lin <frankyl@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Arend van Spriel authored
The function brcmf_sdio_buffrw() is intended to be used for transfering list of packets using scatter-gather functionality. Rename function to brcmf_sdio_sglist_rw() to clarify this. Reviewed-by: Franky Lin <frankyl@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Arend van Spriel authored
Moving a number of assignments outside of the loop as they are the same for each request. Reviewed-by: Franky Lin <frankyl@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Arend van Spriel authored
Instead of determining the limits for scatter-gather MMC transfer request upon each transmit it is now determined during the probe of the SDIO function. Reviewed-by: Franky Lin <frankyl@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Arend van Spriel authored
The variable max_seg_sz in brcmf_sdio_buffrw() respresents the maximum number of buffers that can be sent in one MMC transfer request. Rename it to max_seg_cnt to avoid confusion. Reviewed-by: Franky Lin <frankyl@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-