- 22 Sep, 2020 3 commits
-
-
Bryan O'Donoghue authored
Uses HW_VALUE_CHANNEL() to extract the channel number from a struct ieee80211_channel->hw_value. Once done we can use the upper bits of the hw_value to encode PHY related data. Signed-off-by:
Bryan O'Donoghue <bryan.odonoghue@linaro.org> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200910150708.2179043-3-bryan.odonoghue@linaro.org
-
Bryan O'Donoghue authored
Adds HW_VALUE_CHANNEL(hw_value) an access macro that will be used to extract the channel number from struct ieee80211_channel->hw_value in preparation for also storing PHY settings for 802.11ac in the upper bits of hw_value. Signed-off-by:
-
Rakesh Pillai authored
Board Data File (BDF) is loaded upon driver boot-up procedure. The right board data file is identified using bus and qmi-board-id. The problem, however, can occur when the (default) board data file cannot fulfill with the vendor requirements and it is necessary to use a different board data file. Also using the chip_id for identifying the board data helps in dealing with different variants of the board data file based on the RF card. If the chip_id is not programmed, a default value of 0xff will be used for parsing the board data file. Add the support to get the variant field from DTSI and use this information along with the chip_id to load the vendor specific BDF. The device tree requires addition strings to define the variant name wifi@a000000 { status = "okay"; qcom,ath10k-calibration-variant = "xyz-v2"; }; wifi@a800000 { status = "okay"; qcom,ath10k-calibration-variant = "xyz-v1"; }; This would create the boarddata identifiers for the board-2.bin search * bus=snoc,qmi-board-id=16,qmi-chip-id=0,variant=xyz-v1 * bus=snoc,qmi-board-id=17,qmi-chip-id=0,variant=xyz-v2 Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.3.1-01040-QCAHLSWMTPLZ-1 Signed-off-by:Rakesh Pillai <pillair@codeaurora.org> Signed-off-by:
-
- 21 Sep, 2020 18 commits
-
-
Bryan O'Donoghue authored
wcn36xx_smd_config_bss_v0() and wcn36xx_smd_config_bss_v1() have been designed to operate in standalone fashion. As a result we can drop the dead code now present in wcn36xx_smd_config_bss() and happily remove one kzalloc from the BSS config path as we do so. Signed-off-by:
Loic Poulain <loic.poulain@linaro.org> Signed-off-by:
-
Bryan O'Donoghue authored
A previous patch added wcn36xx_smd_config_bss_v0() this patch converts the version 0 data-path in wcn36xx_smd_config_bss() to use wcn36xx_smd_config_bss_v0(). Signed-off-by:
-
Bryan O'Donoghue authored
This commit adds wcn36xx_smd_config_bss_v0() as a step along the road of functionally decomposing wcn36xx_smd_config_bss(). Signed-off-by:
-
Bryan O'Donoghue authored
This patch updates wcn36xx_smd_config_bss_v1() to update on internally derived parameters only, specifically making use of STA v1 wrapper routines previously added. Once done we no longer need to pass a struct wcn36xx_hal_config_bss_req_msg which gives us options in later patches to eliminate the kzalloc() in wcn36xx_smd_config_bss entirely. Signed-off-by:
-
Bryan O'Donoghue authored
This commit moves BSS parameter setup to a separate function wcn36xx_smd_set_bss_params(). This will allow for further functional decomposition and fewer kzalloc() operations in subsequent patches. Signed-off-by:
-
Bryan O'Donoghue authored
In order to facilitate functional decomposition of wcn36xx_smd_config_bss() we need to move wcn36xx_smd_set_sta_params() later in function. Signed-off-by:
-
Bryan O'Donoghue authored
This commit functionally decomposes wcn36xx_smd_config_sta into a clearly defined wcn36xx_smd_config_sta_v0 and wcn36xx_smd_config_sta_v1 path. Signed-off-by:
-
Bryan O'Donoghue authored
This commit adds a wrapper function wcn36xx_smd_set_sta_params_v1() which calls into wcn36xx_smd_set_sta_params() and then subsequently sets version-1 specific parameters. Signed-off-by:
-
Bryan O'Donoghue authored
This commit adds wcn36xx_smd_set_bss_vht_params(). The job of this function is to decide if the BSS is VHT capable and if so set the appropriate bit in the BSS parameter structure for passing to the firmware. VHT Channel width set is not set since we don't support 160MHz. Signed-off-by:
-
Bryan O'Donoghue authored
Adds a routine to allow setting the LDPC bit for HT parameter passing inside the version 1 STA parameters data structure. Signed-off-by:
-
Bryan O'Donoghue authored
This commit adds support for setting VHT parameters based on the declared VHT capability bits in the VHT capability structure. We cannot do 160MHz so VHT Channel width set should be zero. Signed-off-by:
-
Bryan O'Donoghue authored
Toggling the LDPC enabled bit is possible only via the extended V1 data-structure. This function provides a means of setting the default depending on chip-type. Signed-off-by:
-
Bryan O'Donoghue authored
This commit adds support for setting default VHT parameters, which are exposed by the extended version 1 STA parameter type. Signed-off-by:
-
Bryan O'Donoghue authored
Add a routine to set some additional default parameters associated with the V1 data structure. Signed-off-by:
-
Bryan O'Donoghue authored
This patch converts the internal data structure used to store data-rates from version 0 to version 1. This allows us to extend out the internal storage to represent VHT parameters. Using the extended version 1 data-structure allows us to avoid a whole raft of version 1 specific fixup functions. Signed-off-by:
-
Bryan O'Donoghue authored
In order to pass VHT parameters to wcn3680 we need to use a super-set of the V1 data-structures with additional VHT parameters tacked on. This patch adds the additional fields to the STA and BSS parameter structures. Since neither wcn3620 nor wcn3660 support VHT the size of the passed message is fixed to the previous message length. Subsequent changes will differentiate between wcn3620/wcn3660 and wcn3680 which does use the larger message size. Signed-off-by:
-
Govind Singh authored
IPQ8074 HW uses rproc with AHB as underlying hif layer. Move rproc references from common core layer to target hif layer. Remove IS_ENABLED check for CONFIG_REMOTEPROC as it's not required anymore. No functional changes. Compile tested only. Signed-off-by:
Govind Singh <govinds@codeaurora.org> Signed-off-by:
-
Brooke Basile authored
Calls to usb_kill_anchored_urbs() after usb_kill_urb() on multiprocessor systems create a race condition in which usb_kill_anchored_urbs() deallocates the URB before the completer callback is called in usb_kill_urb(), resulting in a use-after-free. To fix this, add proper lock protection to usb_kill_urb() calls that can possibly run concurrently with usb_kill_anchored_urbs(). Reported-by: syzbot+89bd486af9427a9fc605@syzkaller.appspotmail.com Link: https://syzkaller.appspot.com/bug?id=cabffad18eb74197f84871802fd2c5117b61febfSigned-off-by:
Brooke Basile <brookebasile@gmail.com> Signed-off-by:
-
- 12 Sep, 2020 19 commits
-
-
Barry Song authored
Rather than doing request_irq and then disabling the irq immediately, it should be safer to use IRQ_NOAUTOEN flag for the irq. It removes any gap between request_irq() and disable_irq(). Cc: Salil Mehta <salil.mehta@huawei.com> Reviewed-by:
Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by:
Barry Song <song.bao.hua@hisilicon.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Grygorii Strashko says: ==================== net: ethernet: ti: ale: add static configuration As existing, as newly introduced CPSW ALE versions have differences in supported features and ALE table formats. Especially it's actual for the recent AM65x/J721E/J7200 and future AM64x SoCs, which supports more features like: auto-aging, classifiers, Link aggregation, additional HW filtering, etc. The existing ALE configuration interface is not practical in terms of adding new features and requires consumers to program a lot static parameters. And any attempt to add new features will case endless adding and maintaining different combination of flags and options. Because CPSW ALE configuration is static and fixed for SoC (or set of SoC), It is reasonable to add support for static ALE configurations inside ALE module. This series introduces static ALE configuration table for different ALE variants and provides option for consumers to select required ALE configuration by providing ALE const char *dev_id identifier (Patch 2). And all existing driver have been switched to use new approach (Patches 3-6). After this ALE HW auto-ageing feature can be enabled for AM65x CPSW ALE variant (Patch 7). Finally, Patches 8-9 introduces tables to describe the ALE VLAN entries fields as the ALE VLAN entries are too much differ between different TI CPSW ALE versions. So, handling them using flags, defines and get/set functions are became over-complicated. Patch 1 - is preparation patch Changes in v3: - fixed comment for Patch 2 Changes in v2: - fixed sparse warnings v2: https://lore.kernel.org/patchwork/cover/1301684/ v1: https://lore.kernel.org/patchwork/cover/1301048/ ==================== Signed-off-by:
-
Grygorii Strashko authored
The TI J721E (CPSW9g) ALE version is similar, in general, to Sitara AM3/4/5 CPSW ALE, but has more extended functions and different ALE VLAN entry format. This patch adds support for for multi port TI J721E (CPSW9g) ALE variant. Signed-off-by:
Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by:
-
Grygorii Strashko authored
The ALE VLAN entries are too much differ between different TI CPSW ALE versions. So, handling them using flags, defines and get/set functions became over-complicated. This patch introduces tables to describe the ALE VLAN entries fields, which are different between TI CPSW ALE versions, and new get/set access functions. It also allows to detect incorrect access to not available ALL entry fields. Signed-off-by:
-
Grygorii Strashko authored
The AM65x ALE supports HW auto-ageing which can be enabled by programming ageing interval in ALE_AGING_TIMER register. For this CPSW fck_clk frequency has to be know by ALE. This patch extends cpsw_ale_params with bus_freq field and enables ALE HW auto ageing for AM65x CPSW2G ALE version. Signed-off-by:
-
Grygorii Strashko authored
Hence all existing driver updated to use ALE dev_id the usage of ale dev_id can be made mandatory and cpsw_ale_create() can be updated to use "features" property from ALE static configuration. Signed-off-by:
-
Grygorii Strashko authored
The previous patch has introduced possibility to select CPSW ALE by using ALE dev_id identifier. Switch TI TI AM65x/J721E CPSW NUSS driver to use dev_id. Signed-off-by:
-
Grygorii Strashko authored
The previous patch has introduced possibility to select CPSW ALE by using ALE dev_id identifier. Switch TI Keystone 2 NETCP driver to use dev_id and perform clean up by removing "ale_entries" configuration code. Signed-off-by:
-
Grygorii Strashko authored
The previous patch has introduced possibility to select CPSW ALE by using ALE dev_id identifier. Switch TI cpsw driver to use dev_id="cpsw" and perform clean up by removing "ale_entries" configuration code. Signed-off-by:
-
Grygorii Strashko authored
As existing, as newly introduced CPSW ALE versions have differences in supported features and ALE table formats. Especially it's actual for the recent AM65x/J721E/J7200 SoC and feature AM64x, which supports features like: auto-aging, classifiers, Link aggregation, additional hw filtering, etc. Existing ALE configuration interface is not practical in terms of adding new features and requires consumers to program a lot static parameters. Any attempt to add new options will case endless adding and maintaining different combination of flags and options. Hence CPSW ALE configuration is static and fixed for SoC (or set of SoC) It is reasonable to add support for static ALE configurations inside ALE module. This patch adds static ALE configuration table for different ALE versions and provides option for consumers to select required ALE configuration by providing ALE const char *dev_id identifier. This feature is not enabled by default until existing CPSW drivers will be modified by follow up patches. Signed-off-by:
-
Grygorii Strashko authored
Add cpsw_ale_get_num_entries() API to return number of ALE table entries and update existing drivers to use it. Signed-off-by:
-
David S. Miller authored
Vladimir Oltean says: ==================== DSA tag_8021q cleanup This small series tries to consolidate the VLAN handling in DSA a little bit. It reworks tag_8021q to be minimally invasive to the dsa_switch_ops structure. This makes the rest of the code a bit easier to follow. ==================== Signed-off-by: -
Vladimir Oltean authored
This reverts commit 314f76d7. Citing that commit message, the call graph was: dsa_slave_vlan_rx_add_vid dsa_port_setup_8021q_tagging | | | | | +-------------+ | | v v dsa_port_vid_add dsa_slave_port_obj_add | | +-------+ +-------+ | | v v dsa_port_vlan_add Now that tag_8021q has its own ops structure, it no longer relies on dsa_port_vid_add, and therefore on the dsa_switch_ops to install its VLANs. So dsa_port_vid_add now only has one single caller. So we can simplify the call graph to what it was before, aka: dsa_slave_vlan_rx_add_vid dsa_slave_port_obj_add | | +-------+ +-------+ | | v v dsa_port_vlan_add Signed-off-by:
Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Vladimir Oltean authored
While working on another tag_8021q driver implementation, some things became apparent: - It is not mandatory for a DSA driver to offload the tag_8021q VLANs by using the VLAN table per se. For example, it can add custom TCAM rules that simply encapsulate RX traffic, and redirect & decapsulate rules for TX traffic. For such a driver, it makes no sense to receive the tag_8021q configuration through the same callback as it receives the VLAN configuration from the bridge and the 8021q modules. - Currently, sja1105 (the only tag_8021q user) sets a priv->expect_dsa_8021q variable to distinguish between the bridge calling, and tag_8021q calling. That can be improved, to say the least. - The crosschip bridging operations are, in fact, stateful already. The list of crosschip_links must be kept by the caller and passed to the relevant tag_8021q functions. So it would be nice if the tag_8021q configuration was more self-contained. This patch attempts to do that. Create a struct dsa_8021q_context which encapsulates a struct dsa_switch, and has 2 function pointers for adding and deleting a VLAN. These will replace the previous channel to the driver, which was through the .port_vlan_add and .port_vlan_del callbacks of dsa_switch_ops. Also put the list of crosschip_links into this dsa_8021q_context. Drivers that don't support cross-chip bridging can simply omit to initialize this list, as long as they dont call any cross-chip function. The sja1105_vlan_add and sja1105_vlan_del functions are refactored into a smaller sja1105_vlan_add_one, which now has 2 entry points: - sja1105_vlan_add, from struct dsa_switch_ops - sja1105_dsa_8021q_vlan_add, from the tag_8021q ops But even this change is fairly trivial. It just reflects the fact that for sja1105, the VLANs from these 2 channels end up in the same hardware table. However that is not necessarily true in the general sense (and that's the reason for making this change). The rest of the patch is mostly plain refactoring of "ds" -> "ctx". The dsa_8021q_context structure needs to be propagated because adding a VLAN is now done through the ops function pointers inside of it. Signed-off-by:
-
Vladimir Oltean authored
There is no point in calling dsa_port_setup_8021q_tagging for each individual port. Additionally, it will become more difficult to do that when we'll have a context structure to tag_8021q (next patch). So refactor this now. Signed-off-by:
-
Vladimir Oltean authored
The previous assumption was that the caller would already have this header file included. Signed-off-by:
-
Rohit Maheshwari authored
This patch moves complete nic tls offload (kTLS) code from crypto directory to drivers/net/ethernet/chelsio/inline_crypto/ch_ktls directory. nic TLS is made a separate ULD of cxgb4. Signed-off-by:
Rohit Maheshwari <rohitm@chelsio.com> Signed-off-by:
-
David S. Miller authored
Edward Cree says: ==================== sfc: encap offloads on EF10 EF10 NICs from the 8000 series onwards support TX offloads (checksumming, TSO) on VXLAN- and NVGRE-encapsulated packets. This series adds driver support for these offloads. Changes from v1: * Fix 'no TXQ of type' error handling in patch #1 (and clear up the misleading comment that inspired the wrong version) * Add comment in patch #5 explaining what the deal with TSOv3 is ==================== Signed-off-by: -
Edward Cree authored
Necessitates an .ndo_features_check, as the EF10 datapath has several limitations on what it can handle. Signed-off-by:
Edward Cree <ecree@solarflare.com> Signed-off-by:
-
