ixgbe: Refactor queue disable logic to take completion time into account

This change is meant to allow us to take completion time into account when
disabling queues. Previously we were just working with hard coded values
for how long we should wait. This worked fine for the standard case where
completion timeout was operating in the 50us to 50ms range, however on
platforms that have higher completion timeout times this was resulting in
Rx queues disable messages being displayed as we weren't waiting long
enough for outstanding Rx DMA completions.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Don Buchholz <donald.buchholz@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

drivers/net/ethernet/intel/ixgbe/ixgbe.h

@@ -855,7 +855,8 @@ void ixgbe_free_rx_resources(struct ixgbe_ring *);
 void ixgbe_free_tx_resources(struct ixgbe_ring *);
 void ixgbe_configure_rx_ring(struct ixgbe_adapter *, struct ixgbe_ring *);
 void ixgbe_configure_tx_ring(struct ixgbe_adapter *, struct ixgbe_ring *);
-void ixgbe_disable_rx_queue(struct ixgbe_adapter *adapter, struct ixgbe_ring *);
+void ixgbe_disable_rx(struct ixgbe_adapter *adapter);
+void ixgbe_disable_tx(struct ixgbe_adapter *adapter);
 void ixgbe_update_stats(struct ixgbe_adapter *adapter);
 int ixgbe_init_interrupt_scheme(struct ixgbe_adapter *adapter);
 bool ixgbe_wol_supported(struct ixgbe_adapter *adapter, u16 device_id,

drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c

@@ -1698,35 +1698,17 @@ static int ixgbe_intr_test(struct ixgbe_adapter *adapter, u64 *data)
 
 static void ixgbe_free_desc_rings(struct ixgbe_adapter *adapter)
 {
-	struct ixgbe_ring *tx_ring = &adapter->test_tx_ring;
-	struct ixgbe_ring *rx_ring = &adapter->test_rx_ring;
-	struct ixgbe_hw *hw = &adapter->hw;
-	u32 reg_ctl;
-
-	/* shut down the DMA engines now so they can be reinitialized later */
+	/* Shut down the DMA engines now so they can be reinitialized later,
+	 * since the test rings and normally used rings should overlap on
+	 * queue 0 we can just use the standard disable Rx/Tx calls and they
+	 * will take care of disabling the test rings for us.
+	 */
 
 	/* first Rx */
-	hw->mac.ops.disable_rx(hw);
-	ixgbe_disable_rx_queue(adapter, rx_ring);
+	ixgbe_disable_rx(adapter);
 
 	/* now Tx */
-	reg_ctl = IXGBE_READ_REG(hw, IXGBE_TXDCTL(tx_ring->reg_idx));
-	reg_ctl &= ~IXGBE_TXDCTL_ENABLE;
-	IXGBE_WRITE_REG(hw, IXGBE_TXDCTL(tx_ring->reg_idx), reg_ctl);
-
-	switch (hw->mac.type) {
-	case ixgbe_mac_82599EB:
-	case ixgbe_mac_X540:
-	case ixgbe_mac_X550:
-	case ixgbe_mac_X550EM_x:
-	case ixgbe_mac_x550em_a:
-		reg_ctl = IXGBE_READ_REG(hw, IXGBE_DMATXCTL);
-		reg_ctl &= ~IXGBE_DMATXCTL_TE;
-		IXGBE_WRITE_REG(hw, IXGBE_DMATXCTL, reg_ctl);
-		break;
-	default:
-		break;
-	}
+	ixgbe_disable_tx(adapter);
 
 	ixgbe_reset(adapter);
 

drivers/net/ethernet/intel/ixgbe/ixgbe_main.c

@@ -4022,38 +4022,6 @@ static void ixgbe_rx_desc_queue_enable(struct ixgbe_adapter *adapter,
 	}
 }
 
-void ixgbe_disable_rx_queue(struct ixgbe_adapter *adapter,
-			    struct ixgbe_ring *ring)
-{
-	struct ixgbe_hw *hw = &adapter->hw;
-	int wait_loop = IXGBE_MAX_RX_DESC_POLL;
-	u32 rxdctl;
-	u8 reg_idx = ring->reg_idx;
-
-	if (ixgbe_removed(hw->hw_addr))
-		return;
-	rxdctl = IXGBE_READ_REG(hw, IXGBE_RXDCTL(reg_idx));
-	rxdctl &= ~IXGBE_RXDCTL_ENABLE;
-
-	/* write value back with RXDCTL.ENABLE bit cleared */
-	IXGBE_WRITE_REG(hw, IXGBE_RXDCTL(reg_idx), rxdctl);
-
-	if (hw->mac.type == ixgbe_mac_82598EB &&
-	    !(IXGBE_READ_REG(hw, IXGBE_LINKS) & IXGBE_LINKS_UP))
-		return;
-
-	/* the hardware may take up to 100us to really disable the rx queue */
-	do {
-		udelay(10);
-		rxdctl = IXGBE_READ_REG(hw, IXGBE_RXDCTL(reg_idx));
-	} while (--wait_loop && (rxdctl & IXGBE_RXDCTL_ENABLE));
-
-	if (!wait_loop) {
-		e_err(drv, "RXDCTL.ENABLE on Rx queue %d not cleared within "
-		      "the polling period\n", reg_idx);
-	}
-}
-
 void ixgbe_configure_rx_ring(struct ixgbe_adapter *adapter,
 			     struct ixgbe_ring *ring)
 {
@@ -4063,9 +4031,13 @@ void ixgbe_configure_rx_ring(struct ixgbe_adapter *adapter,
 	u32 rxdctl;
 	u8 reg_idx = ring->reg_idx;
 
-	/* disable queue to avoid issues while updating state */
+	/* disable queue to avoid use of these values while updating state */
 	rxdctl = IXGBE_READ_REG(hw, IXGBE_RXDCTL(reg_idx));
-	ixgbe_disable_rx_queue(adapter, ring);
+	rxdctl &= ~IXGBE_RXDCTL_ENABLE;
+
+	/* write value back with RXDCTL.ENABLE bit cleared */
+	IXGBE_WRITE_REG(hw, IXGBE_RXDCTL(reg_idx), rxdctl);
+	IXGBE_WRITE_FLUSH(hw);
 
 	IXGBE_WRITE_REG(hw, IXGBE_RDBAL(reg_idx), (rdba & DMA_BIT_MASK(32)));
 	IXGBE_WRITE_REG(hw, IXGBE_RDBAH(reg_idx), (rdba >> 32));
@@ -5633,6 +5605,212 @@ void ixgbe_up(struct ixgbe_adapter *adapter)
 	ixgbe_up_complete(adapter);
 }
 
+static unsigned long ixgbe_get_completion_timeout(struct ixgbe_adapter *adapter)
+{
+	u16 devctl2;
+
+	pcie_capability_read_word(adapter->pdev, PCI_EXP_DEVCTL2, &devctl2);
+
+	switch (devctl2 & IXGBE_PCIDEVCTRL2_TIMEO_MASK) {
+	case IXGBE_PCIDEVCTRL2_17_34s:
+	case IXGBE_PCIDEVCTRL2_4_8s:
+		/* For now we cap the upper limit on delay to 2 seconds
+		 * as we end up going up to 34 seconds of delay in worst
+		 * case timeout value.
+		 */
+	case IXGBE_PCIDEVCTRL2_1_2s:
+		return 2000000ul;	/* 2.0 s */
+	case IXGBE_PCIDEVCTRL2_260_520ms:
+		return 520000ul;	/* 520 ms */
+	case IXGBE_PCIDEVCTRL2_65_130ms:
+		return 130000ul;	/* 130 ms */
+	case IXGBE_PCIDEVCTRL2_16_32ms:
+		return 32000ul;		/* 32 ms */
+	case IXGBE_PCIDEVCTRL2_1_2ms:
+		return 2000ul;		/* 2 ms */
+	case IXGBE_PCIDEVCTRL2_50_100us:
+		return 100ul;		/* 100 us */
+	case IXGBE_PCIDEVCTRL2_16_32ms_def:
+		return 32000ul;		/* 32 ms */
+	default:
+		break;
+	}
+
+	/* We shouldn't need to hit this path, but just in case default as
+	 * though completion timeout is not supported and support 32ms.
+	 */
+	return 32000ul;
+}
+
+void ixgbe_disable_rx(struct ixgbe_adapter *adapter)
+{
+	unsigned long wait_delay, delay_interval;
+	struct ixgbe_hw *hw = &adapter->hw;
+	int i, wait_loop;
+	u32 rxdctl;
+
+	/* disable receives */
+	hw->mac.ops.disable_rx(hw);
+
+	if (ixgbe_removed(hw->hw_addr))
+		return;
+
+	/* disable all enabled Rx queues */
+	for (i = 0; i < adapter->num_rx_queues; i++) {
+		struct ixgbe_ring *ring = adapter->rx_ring[i];
+		u8 reg_idx = ring->reg_idx;
+
+		rxdctl = IXGBE_READ_REG(hw, IXGBE_RXDCTL(reg_idx));
+		rxdctl &= ~IXGBE_RXDCTL_ENABLE;
+		rxdctl |= IXGBE_RXDCTL_SWFLSH;
+
+		/* write value back with RXDCTL.ENABLE bit cleared */
+		IXGBE_WRITE_REG(hw, IXGBE_RXDCTL(reg_idx), rxdctl);
+	}
+
+	/* RXDCTL.EN may not change on 82598 if link is down, so skip it */
+	if (hw->mac.type == ixgbe_mac_82598EB &&
+	    !(IXGBE_READ_REG(hw, IXGBE_LINKS) & IXGBE_LINKS_UP))
+		return;
+
+	/* Determine our minimum delay interval. We will increase this value
+	 * with each subsequent test. This way if the device returns quickly
+	 * we should spend as little time as possible waiting, however as
+	 * the time increases we will wait for larger periods of time.
+	 *
+	 * The trick here is that we increase the interval using the
+	 * following pattern: 1x 3x 5x 7x 9x 11x 13x 15x 17x 19x. The result
+	 * of that wait is that it totals up to 100x whatever interval we
+	 * choose. Since our minimum wait is 100us we can just divide the
+	 * total timeout by 100 to get our minimum delay interval.
+	 */
+	delay_interval = ixgbe_get_completion_timeout(adapter) / 100;
+
+	wait_loop = IXGBE_MAX_RX_DESC_POLL;
+	wait_delay = delay_interval;
+
+	while (wait_loop--) {
+		usleep_range(wait_delay, wait_delay + 10);
+		wait_delay += delay_interval * 2;
+		rxdctl = 0;
+
+		/* OR together the reading of all the active RXDCTL registers,
+		 * and then test the result. We need the disable to complete
+		 * before we start freeing the memory and invalidating the
+		 * DMA mappings.
+		 */
+		for (i = 0; i < adapter->num_rx_queues; i++) {
+			struct ixgbe_ring *ring = adapter->rx_ring[i];
+			u8 reg_idx = ring->reg_idx;
+
+			rxdctl |= IXGBE_READ_REG(hw, IXGBE_RXDCTL(reg_idx));
+		}
+
+		if (!(rxdctl & IXGBE_RXDCTL_ENABLE))
+			return;
+	}
+
+	e_err(drv,
+	      "RXDCTL.ENABLE for one or more queues not cleared within the polling period\n");
+}
+
+void ixgbe_disable_tx(struct ixgbe_adapter *adapter)
+{
+	unsigned long wait_delay, delay_interval;
+	struct ixgbe_hw *hw = &adapter->hw;
+	int i, wait_loop;
+	u32 txdctl;
+
+	if (ixgbe_removed(hw->hw_addr))
+		return;
+
+	/* disable all enabled Tx queues */
+	for (i = 0; i < adapter->num_tx_queues; i++) {
+		struct ixgbe_ring *ring = adapter->tx_ring[i];
+		u8 reg_idx = ring->reg_idx;
+
+		IXGBE_WRITE_REG(hw, IXGBE_TXDCTL(reg_idx), IXGBE_TXDCTL_SWFLSH);
+	}
+
+	/* disable all enabled XDP Tx queues */
+	for (i = 0; i < adapter->num_xdp_queues; i++) {
+		struct ixgbe_ring *ring = adapter->xdp_ring[i];
+		u8 reg_idx = ring->reg_idx;
+
+		IXGBE_WRITE_REG(hw, IXGBE_TXDCTL(reg_idx), IXGBE_TXDCTL_SWFLSH);
+	}
+
+	/* If the link is not up there shouldn't be much in the way of
+	 * pending transactions. Those that are left will be flushed out
+	 * when the reset logic goes through the flush sequence to clean out
+	 * the pending Tx transactions.
+	 */
+	if (!(IXGBE_READ_REG(hw, IXGBE_LINKS) & IXGBE_LINKS_UP))
+		goto dma_engine_disable;
+
+	/* Determine our minimum delay interval. We will increase this value
+	 * with each subsequent test. This way if the device returns quickly
+	 * we should spend as little time as possible waiting, however as
+	 * the time increases we will wait for larger periods of time.
+	 *
+	 * The trick here is that we increase the interval using the
+	 * following pattern: 1x 3x 5x 7x 9x 11x 13x 15x 17x 19x. The result
+	 * of that wait is that it totals up to 100x whatever interval we
+	 * choose. Since our minimum wait is 100us we can just divide the
+	 * total timeout by 100 to get our minimum delay interval.
+	 */
+	delay_interval = ixgbe_get_completion_timeout(adapter) / 100;
+
+	wait_loop = IXGBE_MAX_RX_DESC_POLL;
+	wait_delay = delay_interval;
+
+	while (wait_loop--) {
+		usleep_range(wait_delay, wait_delay + 10);
+		wait_delay += delay_interval * 2;
+		txdctl = 0;
+
+		/* OR together the reading of all the active TXDCTL registers,
+		 * and then test the result. We need the disable to complete
+		 * before we start freeing the memory and invalidating the
+		 * DMA mappings.
+		 */
+		for (i = 0; i < adapter->num_tx_queues; i++) {
+			struct ixgbe_ring *ring = adapter->tx_ring[i];
+			u8 reg_idx = ring->reg_idx;
+
+			txdctl |= IXGBE_READ_REG(hw, IXGBE_TXDCTL(reg_idx));
+		}
+		for (i = 0; i < adapter->num_xdp_queues; i++) {
+			struct ixgbe_ring *ring = adapter->xdp_ring[i];
+			u8 reg_idx = ring->reg_idx;
+
+			txdctl |= IXGBE_READ_REG(hw, IXGBE_TXDCTL(reg_idx));
+		}
+
+		if (!(txdctl & IXGBE_TXDCTL_ENABLE))
+			goto dma_engine_disable;
+	}
+
+	e_err(drv,
+	      "TXDCTL.ENABLE for one or more queues not cleared within the polling period\n");
+
+dma_engine_disable:
+	/* Disable the Tx DMA engine on 82599 and later MAC */
+	switch (hw->mac.type) {
+	case ixgbe_mac_82599EB:
+	case ixgbe_mac_X540:
+	case ixgbe_mac_X550:
+	case ixgbe_mac_X550EM_x:
+	case ixgbe_mac_x550em_a:
+		IXGBE_WRITE_REG(hw, IXGBE_DMATXCTL,
+				(IXGBE_READ_REG(hw, IXGBE_DMATXCTL) &
+				 ~IXGBE_DMATXCTL_TE));
+		/* fall through */
+	default:
+		break;
+	}
+}
+
 void ixgbe_reset(struct ixgbe_adapter *adapter)
 {
 	struct ixgbe_hw *hw = &adapter->hw;
@@ -5821,13 +5999,8 @@ void ixgbe_down(struct ixgbe_adapter *adapter)
 	netif_carrier_off(netdev);
 	netif_tx_disable(netdev);
 
-	/* disable receives */
-	hw->mac.ops.disable_rx(hw);
-
-	/* disable all enabled rx queues */
-	for (i = 0; i < adapter->num_rx_queues; i++)
-		/* this call also flushes the previous write */
-		ixgbe_disable_rx_queue(adapter, adapter->rx_ring[i]);
+	/* Disable Rx */
+	ixgbe_disable_rx(adapter);
 
 	/* synchronize_sched() needed for pending XDP buffers to drain */
 	if (adapter->xdp_ring[0])
@@ -5859,30 +6032,7 @@ void ixgbe_down(struct ixgbe_adapter *adapter)
 	}
 
 	/* disable transmits in the hardware now that interrupts are off */
-	for (i = 0; i < adapter->num_tx_queues; i++) {
-		u8 reg_idx = adapter->tx_ring[i]->reg_idx;
-		IXGBE_WRITE_REG(hw, IXGBE_TXDCTL(reg_idx), IXGBE_TXDCTL_SWFLSH);
-	}
-	for (i = 0; i < adapter->num_xdp_queues; i++) {
-		u8 reg_idx = adapter->xdp_ring[i]->reg_idx;
-
-		IXGBE_WRITE_REG(hw, IXGBE_TXDCTL(reg_idx), IXGBE_TXDCTL_SWFLSH);
-	}
-
-	/* Disable the Tx DMA engine on 82599 and later MAC */
-	switch (hw->mac.type) {
-	case ixgbe_mac_82599EB:
-	case ixgbe_mac_X540:
-	case ixgbe_mac_X550:
-	case ixgbe_mac_X550EM_x:
-	case ixgbe_mac_x550em_a:
-		IXGBE_WRITE_REG(hw, IXGBE_DMATXCTL,
-				(IXGBE_READ_REG(hw, IXGBE_DMATXCTL) &
-				 ~IXGBE_DMATXCTL_TE));
-		break;
-	default:
-		break;
-	}
+	ixgbe_disable_tx(adapter);
 
 	if (!pci_channel_offline(adapter->pdev))
 		ixgbe_reset(adapter);