Merge remote branch 'kumar/next' into next

Documentation/devicetree/bindings/net/can/fsl-flexcan.txt

+CAN Device Tree Bindings
+------------------------
+2011 Freescale Semiconductor, Inc.
+
+fsl,flexcan-v1.0 nodes
+-----------------------
+In addition to the required compatible-, reg- and interrupt-properties, you can
+also specify which clock source shall be used for the controller.
+
+CPI Clock- Can Protocol Interface Clock
+	This CLK_SRC bit of CTRL(control register) selects the clock source to
+	the CAN Protocol Interface(CPI) to be either the peripheral clock
+	(driven by the PLL) or the crystal oscillator clock. The selected clock
+	is the one fed to the prescaler to generate the Serial Clock (Sclock).
+	The PRESDIV field of CTRL(control register) controls a prescaler that
+	generates the Serial Clock (Sclock), whose period defines the
+	time quantum used to compose the CAN waveform.
+
+Can Engine Clock Source
+	There are two sources for CAN clock
+	- Platform Clock  It represents the bus clock
+	- Oscillator Clock
+
+	Peripheral Clock (PLL)
+	--------------
+		     |
+		    ---------		      -------------
+		    |       |CPI Clock	      | Prescaler |       Sclock
+		    |       |---------------->| (1.. 256) |------------>
+		    ---------		      -------------
+                     |  |
+	--------------  ---------------------CLK_SRC
+	Oscillator Clock
+
+- fsl,flexcan-clock-source : CAN Engine Clock Source.This property selects
+			     the peripheral clock. PLL clock is fed to the
+			     prescaler to generate the Serial Clock (Sclock).
+			     Valid values are "oscillator" and "platform"
+			     "oscillator": CAN engine clock source is oscillator clock.
+			     "platform" The CAN engine clock source is the bus clock
+		             (platform clock).
+
+- fsl,flexcan-clock-divider : for the reference and system clock, an additional
+			      clock divider can be specified.
+- clock-frequency: frequency required to calculate the bitrate for FlexCAN.
+
+Note:
+	- v1.0 of flexcan-v1.0 represent the IP block version for P1010 SOC.
+	- P1010 does not have oscillator as the Clock Source.So the default
+	  Clock Source is platform clock.
+Examples:
+
+	can0@1c000 {
+		compatible = "fsl,flexcan-v1.0";
+		reg = <0x1c000 0x1000>;
+		interrupts = <48 0x2>;
+		interrupt-parent = <&mpic>;
+		fsl,flexcan-clock-source = "platform";
+		fsl,flexcan-clock-divider = <2>;
+		clock-frequency = <fixed by u-boot>;
+	};

Documentation/devicetree/bindings/powerpc/fsl/ifc.txt

+Integrated Flash Controller
+
+Properties:
+- name : Should be ifc
+- compatible : should contain "fsl,ifc". The version of the integrated
+               flash controller can be found in the IFC_REV register at
+               offset zero.
+
+- #address-cells : Should be either two or three.  The first cell is the
+                   chipselect number, and the remaining cells are the
+                   offset into the chipselect.
+- #size-cells : Either one or two, depending on how large each chipselect
+                can be.
+- reg : Offset and length of the register set for the device
+- interrupts : IFC has two interrupts. The first one is the "common"
+               interrupt(CM_EVTER_STAT), and second is the NAND interrupt
+               (NAND_EVTER_STAT).
+
+- ranges : Each range corresponds to a single chipselect, and covers
+           the entire access window as configured.
+
+Child device nodes describe the devices connected to IFC such as NOR (e.g.
+cfi-flash) and NAND (fsl,ifc-nand). There might be board specific devices
+like FPGAs, CPLDs, etc.
+
+Example:
+
+	ifc@ffe1e000 {
+		compatible = "fsl,ifc", "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <1>;
+		reg = <0x0 0xffe1e000 0 0x2000>;
+		interrupts = <16 2 19 2>;
+
+		/* NOR, NAND Flashes and CPLD on board */
+		ranges = <0x0 0x0 0x0 0xee000000 0x02000000
+			  0x1 0x0 0x0 0xffa00000 0x00010000
+			  0x3 0x0 0x0 0xffb00000 0x00020000>;
+
+		flash@0,0 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "cfi-flash";
+			reg = <0x0 0x0 0x2000000>;
+			bank-width = <2>;
+			device-width = <1>;
+
+			partition@0 {
+				/* 32MB for user data */
+				reg = <0x0 0x02000000>;
+				label = "NOR Data";
+			};
+		};
+
+		flash@1,0 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "fsl,ifc-nand";
+			reg = <0x1 0x0 0x10000>;
+
+			partition@0 {
+				/* This location must not be altered  */
+				/* 1MB for u-boot Bootloader Image */
+				reg = <0x0 0x00100000>;
+				label = "NAND U-Boot Image";
+				read-only;
+			};
+		};
+
+		cpld@3,0 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "fsl,p1010rdb-cpld";
+			reg = <0x3 0x0 0x000001f>;
+		};
+	};

Documentation/devicetree/bindings/powerpc/fsl/mpic-timer.txt

+* Freescale MPIC timers
+
+Required properties:
+- compatible: "fsl,mpic-global-timer"
+
+- reg : Contains two regions.  The first is the main timer register bank
+  (GTCCRxx, GTBCRxx, GTVPRxx, GTDRxx).  The second is the timer control
+  register (TCRx) for the group.
+
+- fsl,available-ranges: use <start count> style section to define which
+  timer interrupts can be used.  This property is optional; without this,
+  all timers within the group can be used.
+
+- interrupts: one interrupt per timer in the group, in order, starting
+  with timer zero.  If timer-available-ranges is present, only the
+  interrupts that correspond to available timers shall be present.
+
+Example:
+	/* Note that this requires #interrupt-cells to be 4 */
+	timer0: timer@41100 {
+		compatible = "fsl,mpic-global-timer";
+		reg = <0x41100 0x100 0x41300 4>;
+
+		/* Another AMP partition is using timers 0 and 1 */
+		fsl,available-ranges = <2 2>;
+
+		interrupts = <2 0 3 0
+		              3 0 3 0>;
+	};
+
+	timer1: timer@42100 {
+		compatible = "fsl,mpic-global-timer";
+		reg = <0x42100 0x100 0x42300 4>;
+		interrupts = <4 0 3 0
+		              5 0 3 0
+		              6 0 3 0
+		              7 0 3 0>;
+	};

Documentation/devicetree/bindings/powerpc/fsl/mpic.txt

@@ -190,7 +190,7 @@ EXAMPLE 4
 	 */
 	timer0: timer@41100 {
 		compatible = "fsl,mpic-global-timer";
-		reg = <0x41100 0x100>;
+		reg = <0x41100 0x100 0x41300 4>;
 		interrupts = <0 0 3 0
 		              1 0 3 0
 		              2 0 3 0

arch/powerpc/boot/dts/p1020rdb.dts

@@ -9,12 +9,11 @@
  * option) any later version.
  */
 
-/dts-v1/;
+/include/ "p1020si.dtsi"
+
 / {
-	model = "fsl,P1020";
+	model = "fsl,P1020RDB";
 	compatible = "fsl,P1020RDB";
-	#address-cells = <2>;
-	#size-cells = <2>;
 
 	aliases {
 		serial0 = &serial0;
@@ -26,34 +25,11 @@ aliases {
 		pci1 = &pci1;
 	};
 
-	cpus {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		PowerPC,P1020@0 {
-			device_type = "cpu";
-			reg = <0x0>;
-			next-level-cache = <&L2>;
-		};
-
-		PowerPC,P1020@1 {
-			device_type = "cpu";
-			reg = <0x1>;
-			next-level-cache = <&L2>;
-		};
-	};
-
 	memory {
 		device_type = "memory";
 	};
 
 	localbus@ffe05000 {
-		#address-cells = <2>;
-		#size-cells = <1>;
-		compatible = "fsl,p1020-elbc", "fsl,elbc", "simple-bus";
-		reg = <0 0xffe05000 0 0x1000>;
-		interrupts = <19 2>;
-		interrupt-parent = <&mpic>;
 
 		/* NOR, NAND Flashes and Vitesse 5 port L2 switch */
 		ranges = <0x0 0x0 0x0 0xef000000 0x01000000
@@ -165,88 +141,14 @@ L2switch@2,0 {
 	};
 
 	soc@ffe00000 {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		device_type = "soc";
-		compatible = "fsl,p1020-immr", "simple-bus";
-		ranges = <0x0  0x0 0xffe00000 0x100000>;
-		bus-frequency = <0>;		// Filled out by uboot.
-
-		ecm-law@0 {
-			compatible = "fsl,ecm-law";
-			reg = <0x0 0x1000>;
-			fsl,num-laws = <12>;
-		};
-
-		ecm@1000 {
-			compatible = "fsl,p1020-ecm", "fsl,ecm";
-			reg = <0x1000 0x1000>;
-			interrupts = <16 2>;
-			interrupt-parent = <&mpic>;
-		};
-
-		memory-controller@2000 {
-			compatible = "fsl,p1020-memory-controller";
-			reg = <0x2000 0x1000>;
-			interrupt-parent = <&mpic>;
-			interrupts = <16 2>;
-		};
-
 		i2c@3000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			cell-index = <0>;
-			compatible = "fsl-i2c";
-			reg = <0x3000 0x100>;
-			interrupts = <43 2>;
-			interrupt-parent = <&mpic>;
-			dfsrr;
 			rtc@68 {
 				compatible = "dallas,ds1339";
 				reg = <0x68>;
 			};
 		};
 
-		i2c@3100 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			cell-index = <1>;
-			compatible = "fsl-i2c";
-			reg = <0x3100 0x100>;
-			interrupts = <43 2>;
-			interrupt-parent = <&mpic>;
-			dfsrr;
-		};
-
-		serial0: serial@4500 {
-			cell-index = <0>;
-			device_type = "serial";
-			compatible = "ns16550";
-			reg = <0x4500 0x100>;
-			clock-frequency = <0>;
-			interrupts = <42 2>;
-			interrupt-parent = <&mpic>;
-		};
-
-		serial1: serial@4600 {
-			cell-index = <1>;
-			device_type = "serial";
-			compatible = "ns16550";
-			reg = <0x4600 0x100>;
-			clock-frequency = <0>;
-			interrupts = <42 2>;
-			interrupt-parent = <&mpic>;
-		};
-
 		spi@7000 {
-			cell-index = <0>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "fsl,espi";
-			reg = <0x7000 0x1000>;
-			interrupts = <59 0x2>;
-			interrupt-parent = <&mpic>;
-			mode = "cpu";
 
 			fsl_m25p80@0 {
 				#address-cells = <1>;
@@ -294,66 +196,7 @@ partition@900000 {
 			};
 		};
 
-		gpio: gpio-controller@f000 {
-			#gpio-cells = <2>;
-			compatible = "fsl,mpc8572-gpio";
-			reg = <0xf000 0x100>;
-			interrupts = <47 0x2>;
-			interrupt-parent = <&mpic>;
-			gpio-controller;
-		};
-
-		L2: l2-cache-controller@20000 {
-			compatible = "fsl,p1020-l2-cache-controller";
-			reg = <0x20000 0x1000>;
-			cache-line-size = <32>;	// 32 bytes
-			cache-size = <0x40000>; // L2,256K
-			interrupt-parent = <&mpic>;
-			interrupts = <16 2>;
-		};
-
-		dma@21300 {
-			#address-cells = <1>;
-			#size-cells = <1>;
-			compatible = "fsl,eloplus-dma";
-			reg = <0x21300 0x4>;
-			ranges = <0x0 0x21100 0x200>;
-			cell-index = <0>;
-			dma-channel@0 {
-				compatible = "fsl,eloplus-dma-channel";
-				reg = <0x0 0x80>;
-				cell-index = <0>;
-				interrupt-parent = <&mpic>;
-				interrupts = <20 2>;
-			};
-			dma-channel@80 {
-				compatible = "fsl,eloplus-dma-channel";
-				reg = <0x80 0x80>;
-				cell-index = <1>;
-				interrupt-parent = <&mpic>;
-				interrupts = <21 2>;
-			};
-			dma-channel@100 {
-				compatible = "fsl,eloplus-dma-channel";
-				reg = <0x100 0x80>;
-				cell-index = <2>;
-				interrupt-parent = <&mpic>;
-				interrupts = <22 2>;
-			};
-			dma-channel@180 {
-				compatible = "fsl,eloplus-dma-channel";
-				reg = <0x180 0x80>;
-				cell-index = <3>;
-				interrupt-parent = <&mpic>;
-				interrupts = <23 2>;
-			};
-		};
-
 		mdio@24000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "fsl,etsec2-mdio";
-			reg = <0x24000 0x1000 0xb0030 0x4>;
 
 			phy0: ethernet-phy@0 {
 				interrupt-parent = <&mpic>;
@@ -369,10 +212,6 @@ phy1: ethernet-phy@1 {
 		};
 
 		mdio@25000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "fsl,etsec2-tbi";
-			reg = <0x25000 0x1000 0xb1030 0x4>;
 
 			tbi0: tbi-phy@11 {
 				reg = <0x11>;
@@ -381,97 +220,25 @@ tbi0: tbi-phy@11 {
 		};
 
 		enet0: ethernet@b0000 {
-			#address-cells = <1>;
-			#size-cells = <1>;
-			device_type = "network";
-			model = "eTSEC";
-			compatible = "fsl,etsec2";
-			fsl,num_rx_queues = <0x8>;
-			fsl,num_tx_queues = <0x8>;
-			local-mac-address = [ 00 00 00 00 00 00 ];
-			interrupt-parent = <&mpic>;
 			fixed-link = <1 1 1000 0 0>;
 			phy-connection-type = "rgmii-id";
 
-			queue-group@0 {
-				#address-cells = <1>;
-				#size-cells = <1>;
-				reg = <0xb0000 0x1000>;
-				interrupts = <29 2 30 2 34 2>;
-			};
-
-			queue-group@1 {
-				#address-cells = <1>;
-				#size-cells = <1>;
-				reg = <0xb4000 0x1000>;
-				interrupts = <17 2 18 2 24 2>;
-			};
 		};
 
 		enet1: ethernet@b1000 {
-			#address-cells = <1>;
-			#size-cells = <1>;
-			device_type = "network";
-			model = "eTSEC";
-			compatible = "fsl,etsec2";
-			fsl,num_rx_queues = <0x8>;
-			fsl,num_tx_queues = <0x8>;
-			local-mac-address = [ 00 00 00 00 00 00 ];
-			interrupt-parent = <&mpic>;
 			phy-handle = <&phy0>;
 			tbi-handle = <&tbi0>;
 			phy-connection-type = "sgmii";
 
-			queue-group@0 {
-				#address-cells = <1>;
-				#size-cells = <1>;
-				reg = <0xb1000 0x1000>;
-				interrupts = <35 2 36 2 40 2>;
-			};
-
-			queue-group@1 {
-				#address-cells = <1>;
-				#size-cells = <1>;
-				reg = <0xb5000 0x1000>;
-				interrupts = <51 2 52 2 67 2>;
-			};
 		};
 
 		enet2: ethernet@b2000 {
-			#address-cells = <1>;
-			#size-cells = <1>;
-			device_type = "network";
-			model = "eTSEC";
-			compatible = "fsl,etsec2";
-			fsl,num_rx_queues = <0x8>;
-			fsl,num_tx_queues = <0x8>;
-			local-mac-address = [ 00 00 00 00 00 00 ];
-			interrupt-parent = <&mpic>;
 			phy-handle = <&phy1>;
 			phy-connection-type = "rgmii-id";
 
-			queue-group@0 {
-				#address-cells = <1>;
-				#size-cells = <1>;
-				reg = <0xb2000 0x1000>;
-				interrupts = <31 2 32 2 33 2>;
-			};
-
-			queue-group@1 {
-				#address-cells = <1>;
-				#size-cells = <1>;
-				reg = <0xb6000 0x1000>;
-				interrupts = <25 2 26 2 27 2>;
-			};
 		};
 
 		usb@22000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "fsl-usb2-dr";
-			reg = <0x22000 0x1000>;
-			interrupt-parent = <&mpic>;
-			interrupts = <28 0x2>;
 			phy_type = "ulpi";
 		};
 
@@ -481,82 +248,23 @@ since U-Boot doesn't clear the status property when
 		   it enables USB2. OTOH, U-Boot does create a new node
 		   when there isn't any. So, just comment it out.
 		usb@23000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "fsl-usb2-dr";
-			reg = <0x23000 0x1000>;
-			interrupt-parent = <&mpic>;
-			interrupts = <46 0x2>;
 			phy_type = "ulpi";
 		};
 		*/
 
-		sdhci@2e000 {
-			compatible = "fsl,p1020-esdhc", "fsl,esdhc";
-			reg = <0x2e000 0x1000>;
-			interrupts = <72 0x2>;
-			interrupt-parent = <&mpic>;
-			/* Filled in by U-Boot */
-			clock-frequency = <0>;
-		};
-
-		crypto@30000 {
-			compatible = "fsl,sec3.1", "fsl,sec3.0", "fsl,sec2.4",
-				     "fsl,sec2.2", "fsl,sec2.1", "fsl,sec2.0";
-			reg = <0x30000 0x10000>;
-			interrupts = <45 2 58 2>;
-			interrupt-parent = <&mpic>;
-			fsl,num-channels = <4>;
-			fsl,channel-fifo-len = <24>;
-			fsl,exec-units-mask = <0xbfe>;
-			fsl,descriptor-types-mask = <0x3ab0ebf>;
-		};
-
-		mpic: pic@40000 {
-			interrupt-controller;
-			#address-cells = <0>;
-			#interrupt-cells = <2>;
-			reg = <0x40000 0x40000>;
-			compatible = "chrp,open-pic";
-			device_type = "open-pic";
-		};
-
-		msi@41600 {
-			compatible = "fsl,p1020-msi", "fsl,mpic-msi";
-			reg = <0x41600 0x80>;
-			msi-available-ranges = <0 0x100>;
-			interrupts = <
-				0xe0 0
-				0xe1 0
-				0xe2 0
-				0xe3 0
-				0xe4 0
-				0xe5 0
-				0xe6 0
-				0xe7 0>;
-			interrupt-parent = <&mpic>;
-		};
-
-		global-utilities@e0000 {	//global utilities block
-			compatible = "fsl,p1020-guts";
-			reg = <0xe0000 0x1000>;
-			fsl,has-rstcr;
-		};
 	};
 
 	pci0: pcie@ffe09000 {
-		compatible = "fsl,mpc8548-pcie";
-		device_type = "pci";
-		#interrupt-cells = <1>;
-		#size-cells = <2>;
-		#address-cells = <3>;
-		reg = <0 0xffe09000 0 0x1000>;
-		bus-range = <0 255>;
 		ranges = <0x2000000 0x0 0xa0000000 0 0xa0000000 0x0 0x20000000
 			  0x1000000 0x0 0x00000000 0 0xffc10000 0x0 0x10000>;
-		clock-frequency = <33333333>;
-		interrupt-parent = <&mpic>;
-		interrupts = <16 2>;
+		interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
+		interrupt-map = <
+			/* IDSEL 0x0 */
+			0000 0x0 0x0 0x1 &mpic 0x4 0x1
+			0000 0x0 0x0 0x2 &mpic 0x5 0x1
+			0000 0x0 0x0 0x3 &mpic 0x6 0x1
+			0000 0x0 0x0 0x4 &mpic 0x7 0x1
+			>;
 		pcie@0 {
 			reg = <0x0 0x0 0x0 0x0 0x0>;
 			#size-cells = <2>;
@@ -573,18 +281,16 @@ pcie@0 {
 	};
 
 	pci1: pcie@ffe0a000 {
-		compatible = "fsl,mpc8548-pcie";
-		device_type = "pci";
-		#interrupt-cells = <1>;
-		#size-cells = <2>;
-		#address-cells = <3>;
-		reg = <0 0xffe0a000 0 0x1000>;
-		bus-range = <0 255>;
 		ranges = <0x2000000 0x0 0x80000000 0 0x80000000 0x0 0x20000000
 			  0x1000000 0x0 0x00000000 0 0xffc00000 0x0 0x10000>;
-		clock-frequency = <33333333>;
-		interrupt-parent = <&mpic>;
-		interrupts = <16 2>;
+		interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
+		interrupt-map = <
+			/* IDSEL 0x0 */
+			0000 0x0 0x0 0x1 &mpic 0x0 0x1
+			0000 0x0 0x0 0x2 &mpic 0x1 0x1
+			0000 0x0 0x0 0x3 &mpic 0x2 0x1
+			0000 0x0 0x0 0x4 &mpic 0x3 0x1
+			>;
 		pcie@0 {
 			reg = <0x0 0x0 0x0 0x0 0x0>;
 			#size-cells = <2>;

arch/powerpc/boot/dts/p1020rdb_camp_core0.dts

+/*
+ * P1020 RDB  Core0 Device Tree Source in CAMP mode.
+ *
+ * In CAMP mode, each core needs to have its own dts. Only mpic and L2 cache
+ * can be shared, all the other devices must be assigned to one core only.
+ * This dts file allows core0 to have memory, l2, i2c, spi, gpio, tdm, dma, usb,
+ * eth1, eth2, sdhc, crypto, global-util, message, pci0, pci1, msi.
+ *
+ * Please note to add "-b 0" for core0's dts compiling.
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+/include/ "p1020si.dtsi"
+
+/ {
+	model = "fsl,P1020RDB";
+	compatible = "fsl,P1020RDB", "fsl,MPC85XXRDB-CAMP";
+
+	aliases {
+		ethernet1 = &enet1;
+		ethernet2 = &enet2;
+		serial0 = &serial0;
+		pci0 = &pci0;
+		pci1 = &pci1;
+	};
+
+	cpus {
+		PowerPC,P1020@1 {
+		status = "disabled";
+		};
+	};
+
+	memory {
+		device_type = "memory";
+	};
+
+	localbus@ffe05000 {
+		status = "disabled";
+	};
+
+	soc@ffe00000 {
+		i2c@3000 {
+			rtc@68 {
+				compatible = "dallas,ds1339";
+				reg = <0x68>;
+			};
+		};
+
+		serial1: serial@4600 {
+			status = "disabled";
+		};
+
+		spi@7000 {
+			fsl_m25p80@0 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				compatible = "fsl,espi-flash";
+				reg = <0>;
+				linux,modalias = "fsl_m25p80";
+				spi-max-frequency = <40000000>;
+
+				partition@0 {
+					/* 512KB for u-boot Bootloader Image */
+					reg = <0x0 0x00080000>;
+					label = "SPI (RO) U-Boot Image";
+					read-only;
+				};
+
+				partition@80000 {
+					/* 512KB for DTB Image */
+					reg = <0x00080000 0x00080000>;
+					label = "SPI (RO) DTB Image";
+					read-only;
+				};
+
+				partition@100000 {
+					/* 4MB for Linux Kernel Image */
+					reg = <0x00100000 0x00400000>;
+					label = "SPI (RO) Linux Kernel Image";
+					read-only;
+				};
+
+				partition@500000 {
+					/* 4MB for Compressed RFS Image */
+					reg = <0x00500000 0x00400000>;
+					label = "SPI (RO) Compressed RFS Image";
+					read-only;
+				};
+
+				partition@900000 {
+					/* 7MB for JFFS2 based RFS */
+					reg = <0x00900000 0x00700000>;
+					label = "SPI (RW) JFFS2 RFS";
+				};
+			};
+		};
+
+		mdio@24000 {
+			phy0: ethernet-phy@0 {
+				interrupt-parent = <&mpic>;
+				interrupts = <3 1>;
+				reg = <0x0>;
+			};
+			phy1: ethernet-phy@1 {
+				interrupt-parent = <&mpic>;
+				interrupts = <2 1>;
+				reg = <0x1>;
+			};
+		};
+
+		mdio@25000 {
+			tbi0: tbi-phy@11 {
+				reg = <0x11>;
+				device_type = "tbi-phy";
+			};
+		};
+
+		enet0: ethernet@b0000 {
+			status = "disabled";
+		};
+
+		enet1: ethernet@b1000 {
+			phy-handle = <&phy0>;
+			tbi-handle = <&tbi0>;
+			phy-connection-type = "sgmii";
+		};
+
+		enet2: ethernet@b2000 {
+			phy-handle = <&phy1>;
+			phy-connection-type = "rgmii-id";
+		};
+
+		usb@22000 {
+			phy_type = "ulpi";
+		};
+
+		/* USB2 is shared with localbus, so it must be disabled
+		   by default. We can't put 'status = "disabled";' here
+		   since U-Boot doesn't clear the status property when
+		   it enables USB2. OTOH, U-Boot does create a new node
+		   when there isn't any. So, just comment it out.
+		usb@23000 {
+			phy_type = "ulpi";
+		};
+		*/
+
+		mpic: pic@40000 {
+			protected-sources = <
+			42 29 30 34	/* serial1, enet0-queue-group0 */
+			17 18 24 45	/* enet0-queue-group1, crypto */
+			>;
+		};
+
+	};
+
+	pci0: pcie@ffe09000 {
+		ranges = <0x2000000 0x0 0xa0000000 0 0xa0000000 0x0 0x20000000
+			  0x1000000 0x0 0x00000000 0 0xffc10000 0x0 0x10000>;
+		interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
+		interrupt-map = <
+			/* IDSEL 0x0 */
+			0000 0x0 0x0 0x1 &mpic 0x4 0x1
+			0000 0x0 0x0 0x2 &mpic 0x5 0x1
+			0000 0x0 0x0 0x3 &mpic 0x6 0x1
+			0000 0x0 0x0 0x4 &mpic 0x7 0x1
+			>;
+		pcie@0 {
+			reg = <0x0 0x0 0x0 0x0 0x0>;
+			#size-cells = <2>;
+			#address-cells = <3>;
+			device_type = "pci";
+			ranges = <0x2000000 0x0 0xa0000000
+				  0x2000000 0x0 0xa0000000
+				  0x0 0x20000000
+
+				  0x1000000 0x0 0x0
+				  0x1000000 0x0 0x0
+				  0x0 0x100000>;
+		};
+	};
+
+	pci1: pcie@ffe0a000 {
+		ranges = <0x2000000 0x0 0x80000000 0 0x80000000 0x0 0x20000000
+			  0x1000000 0x0 0x00000000 0 0xffc00000 0x0 0x10000>;
+		interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
+		interrupt-map = <
+			/* IDSEL 0x0 */
+			0000 0x0 0x0 0x1 &mpic 0x0 0x1
+			0000 0x0 0x0 0x2 &mpic 0x1 0x1
+			0000 0x0 0x0 0x3 &mpic 0x2 0x1
+			0000 0x0 0x0 0x4 &mpic 0x3 0x1
+			>;
+		pcie@0 {
+			reg = <0x0 0x0 0x0 0x0 0x0>;
+			#size-cells = <2>;
+			#address-cells = <3>;
+			device_type = "pci";
+			ranges = <0x2000000 0x0 0x80000000
+				  0x2000000 0x0 0x80000000
+				  0x0 0x20000000
+
+				  0x1000000 0x0 0x0
+				  0x1000000 0x0 0x0
+				  0x0 0x100000>;
+		};
+	};
+};

arch/powerpc/boot/dts/p1020rdb_camp_core1.dts

+/*
+ * P1020 RDB Core1 Device Tree Source in CAMP mode.
+ *
+ * In CAMP mode, each core needs to have its own dts. Only mpic and L2 cache
+ * can be shared, all the other devices must be assigned to one core only.
+ * This dts allows core1 to have l2, eth0, crypto.
+ *
+ * Please note to add "-b 1" for core1's dts compiling.
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+/include/ "p1020si.dtsi"
+
+/ {
+	model = "fsl,P1020RDB";
+	compatible = "fsl,P1020RDB", "fsl,MPC85XXRDB-CAMP";
+
+	aliases {
+		ethernet0 = &enet0;
+		serial0 = &serial1;
+		};
+
+	cpus {
+		PowerPC,P1020@0 {
+		status = "disabled";
+		};
+	};
+
+	memory {
+		device_type = "memory";
+	};
+
+	localbus@ffe05000 {
+		status = "disabled";
+	};
+
+	soc@ffe00000 {
+		ecm-law@0 {
+			status = "disabled";
+		};
+
+		ecm@1000 {
+			status = "disabled";
+		};
+
+		memory-controller@2000 {
+			status = "disabled";
+		};
+
+		i2c@3000 {
+			status = "disabled";
+		};
+
+		i2c@3100 {
+			status = "disabled";
+		};
+
+		serial0: serial@4500 {
+			status = "disabled";
+		};
+
+		spi@7000 {
+			status = "disabled";
+		};
+
+		gpio: gpio-controller@f000 {
+			status = "disabled";
+		};
+
+		dma@21300 {
+			status = "disabled";
+		};
+
+		mdio@24000 {
+			status = "disabled";
+		};
+
+		mdio@25000 {
+			status = "disabled";
+		};
+
+		enet0: ethernet@b0000 {
+			fixed-link = <1 1 1000 0 0>;
+			phy-connection-type = "rgmii-id";
+
+		};
+
+		enet1: ethernet@b1000 {
+			status = "disabled";
+		};
+
+		enet2: ethernet@b2000 {
+			status = "disabled";
+		};
+
+		usb@22000 {
+			status = "disabled";
+		};
+
+		sdhci@2e000 {
+			status = "disabled";
+		};
+
+		mpic: pic@40000 {
+			protected-sources = <
+			16 		/* ecm, mem, L2, pci0, pci1 */
+			43 42 59	/* i2c, serial0, spi */
+			47 63 62 	/* gpio, tdm */
+			20 21 22 23	/* dma */
+			03 02 		/* mdio */
+			35 36 40	/* enet1-queue-group0 */
+			51 52 67	/* enet1-queue-group1 */
+			31 32 33	/* enet2-queue-group0 */
+			25 26 27	/* enet2-queue-group1 */
+			28 72 58 	/* usb, sdhci, crypto */
+			0xb0 0xb1 0xb2	/* message */
+			0xb3 0xb4 0xb5
+			0xb6 0xb7
+			0xe0 0xe1 0xe2	/* msi */
+			0xe3 0xe4 0xe5
+			0xe6 0xe7		/* sdhci, crypto , pci */
+			>;
+		};
+
+		msi@41600 {
+			status = "disabled";
+		};
+
+		global-utilities@e0000 {	//global utilities block
+			status = "disabled";
+		};
+
+	};
+
+	pci0: pcie@ffe09000 {
+		status = "disabled";
+	};
+
+	pci1: pcie@ffe0a000 {
+		status = "disabled";
+	};
+};

arch/powerpc/boot/dts/p1020si.dtsi

+/*
+ * P1020si Device Tree Source
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+/dts-v1/;
+/ {
+	compatible = "fsl,P1020";
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		PowerPC,P1020@0 {
+			device_type = "cpu";
+			reg = <0x0>;
+			next-level-cache = <&L2>;
+		};
+
+		PowerPC,P1020@1 {
+			device_type = "cpu";
+			reg = <0x1>;
+			next-level-cache = <&L2>;
+		};
+	};
+
+	localbus@ffe05000 {
+		#address-cells = <2>;
+		#size-cells = <1>;
+		compatible = "fsl,p1020-elbc", "fsl,elbc", "simple-bus";
+		reg = <0 0xffe05000 0 0x1000>;
+		interrupts = <19 2>;
+		interrupt-parent = <&mpic>;
+	};
+
+	soc@ffe00000 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		device_type = "soc";
+		compatible = "fsl,p1020-immr", "simple-bus";
+		ranges = <0x0  0x0 0xffe00000 0x100000>;
+		bus-frequency = <0>;		// Filled out by uboot.
+
+		ecm-law@0 {
+			compatible = "fsl,ecm-law";
+			reg = <0x0 0x1000>;
+			fsl,num-laws = <12>;
+		};
+
+		ecm@1000 {
+			compatible = "fsl,p1020-ecm", "fsl,ecm";
+			reg = <0x1000 0x1000>;
+			interrupts = <16 2>;
+			interrupt-parent = <&mpic>;
+		};
+
+		memory-controller@2000 {
+			compatible = "fsl,p1020-memory-controller";
+			reg = <0x2000 0x1000>;
+			interrupt-parent = <&mpic>;
+			interrupts = <16 2>;
+		};
+
+		i2c@3000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			cell-index = <0>;
+			compatible = "fsl-i2c";
+			reg = <0x3000 0x100>;
+			interrupts = <43 2>;
+			interrupt-parent = <&mpic>;
+			dfsrr;
+		};
+
+		i2c@3100 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			cell-index = <1>;
+			compatible = "fsl-i2c";
+			reg = <0x3100 0x100>;
+			interrupts = <43 2>;
+			interrupt-parent = <&mpic>;
+			dfsrr;
+		};
+
+		serial0: serial@4500 {
+			cell-index = <0>;
+			device_type = "serial";
+			compatible = "ns16550";
+			reg = <0x4500 0x100>;
+			clock-frequency = <0>;
+			interrupts = <42 2>;
+			interrupt-parent = <&mpic>;
+		};
+
+		serial1: serial@4600 {
+			cell-index = <1>;
+			device_type = "serial";
+			compatible = "ns16550";
+			reg = <0x4600 0x100>;
+			clock-frequency = <0>;
+			interrupts = <42 2>;
+			interrupt-parent = <&mpic>;
+		};
+
+		spi@7000 {
+			cell-index = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "fsl,espi";
+			reg = <0x7000 0x1000>;
+			interrupts = <59 0x2>;
+			interrupt-parent = <&mpic>;
+			mode = "cpu";
+		};
+
+		gpio: gpio-controller@f000 {
+			#gpio-cells = <2>;
+			compatible = "fsl,mpc8572-gpio";
+			reg = <0xf000 0x100>;
+			interrupts = <47 0x2>;
+			interrupt-parent = <&mpic>;
+			gpio-controller;
+		};
+
+		L2: l2-cache-controller@20000 {
+			compatible = "fsl,p1020-l2-cache-controller";
+			reg = <0x20000 0x1000>;
+			cache-line-size = <32>;	// 32 bytes
+			cache-size = <0x40000>; // L2,256K
+			interrupt-parent = <&mpic>;
+			interrupts = <16 2>;
+		};
+
+		dma@21300 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "fsl,eloplus-dma";
+			reg = <0x21300 0x4>;
+			ranges = <0x0 0x21100 0x200>;
+			cell-index = <0>;
+			dma-channel@0 {
+				compatible = "fsl,eloplus-dma-channel";
+				reg = <0x0 0x80>;
+				cell-index = <0>;
+				interrupt-parent = <&mpic>;
+				interrupts = <20 2>;
+			};
+			dma-channel@80 {
+				compatible = "fsl,eloplus-dma-channel";
+				reg = <0x80 0x80>;
+				cell-index = <1>;
+				interrupt-parent = <&mpic>;
+				interrupts = <21 2>;
+			};
+			dma-channel@100 {
+				compatible = "fsl,eloplus-dma-channel";
+				reg = <0x100 0x80>;
+				cell-index = <2>;
+				interrupt-parent = <&mpic>;
+				interrupts = <22 2>;
+			};
+			dma-channel@180 {
+				compatible = "fsl,eloplus-dma-channel";
+				reg = <0x180 0x80>;
+				cell-index = <3>;
+				interrupt-parent = <&mpic>;
+				interrupts = <23 2>;
+			};
+		};
+
+		mdio@24000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "fsl,etsec2-mdio";
+			reg = <0x24000 0x1000 0xb0030 0x4>;
+
+		};
+
+		mdio@25000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "fsl,etsec2-tbi";
+			reg = <0x25000 0x1000 0xb1030 0x4>;
+
+		};
+
+		enet0: ethernet@b0000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			device_type = "network";
+			model = "eTSEC";
+			compatible = "fsl,etsec2";
+			fsl,num_rx_queues = <0x8>;
+			fsl,num_tx_queues = <0x8>;
+			local-mac-address = [ 00 00 00 00 00 00 ];
+			interrupt-parent = <&mpic>;
+
+			queue-group@0 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0xb0000 0x1000>;
+				interrupts = <29 2 30 2 34 2>;
+			};
+
+			queue-group@1 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0xb4000 0x1000>;
+				interrupts = <17 2 18 2 24 2>;
+			};
+		};
+
+		enet1: ethernet@b1000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			device_type = "network";
+			model = "eTSEC";
+			compatible = "fsl,etsec2";
+			fsl,num_rx_queues = <0x8>;
+			fsl,num_tx_queues = <0x8>;
+			local-mac-address = [ 00 00 00 00 00 00 ];
+			interrupt-parent = <&mpic>;
+
+			queue-group@0 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0xb1000 0x1000>;
+				interrupts = <35 2 36 2 40 2>;
+			};
+
+			queue-group@1 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0xb5000 0x1000>;
+				interrupts = <51 2 52 2 67 2>;
+			};
+		};
+
+		enet2: ethernet@b2000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			device_type = "network";
+			model = "eTSEC";
+			compatible = "fsl,etsec2";
+			fsl,num_rx_queues = <0x8>;
+			fsl,num_tx_queues = <0x8>;
+			local-mac-address = [ 00 00 00 00 00 00 ];
+			interrupt-parent = <&mpic>;
+
+			queue-group@0 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0xb2000 0x1000>;
+				interrupts = <31 2 32 2 33 2>;
+			};
+
+			queue-group@1 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0xb6000 0x1000>;
+				interrupts = <25 2 26 2 27 2>;
+			};
+		};
+
+		usb@22000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "fsl-usb2-dr";
+			reg = <0x22000 0x1000>;
+			interrupt-parent = <&mpic>;
+			interrupts = <28 0x2>;
+		};
+
+		/* USB2 is shared with localbus, so it must be disabled
+		   by default. We can't put 'status = "disabled";' here
+		   since U-Boot doesn't clear the status property when
+		   it enables USB2. OTOH, U-Boot does create a new node
+		   when there isn't any. So, just comment it out.
+		usb@23000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "fsl-usb2-dr";
+			reg = <0x23000 0x1000>;
+			interrupt-parent = <&mpic>;
+			interrupts = <46 0x2>;
+			phy_type = "ulpi";
+		};
+		*/
+
+		sdhci@2e000 {
+			compatible = "fsl,p1020-esdhc", "fsl,esdhc";
+			reg = <0x2e000 0x1000>;
+			interrupts = <72 0x2>;
+			interrupt-parent = <&mpic>;
+			/* Filled in by U-Boot */
+			clock-frequency = <0>;
+		};
+
+		crypto@30000 {
+			compatible = "fsl,sec3.1", "fsl,sec3.0", "fsl,sec2.4",
+				     "fsl,sec2.2", "fsl,sec2.1", "fsl,sec2.0";
+			reg = <0x30000 0x10000>;
+			interrupts = <45 2 58 2>;
+			interrupt-parent = <&mpic>;
+			fsl,num-channels = <4>;
+			fsl,channel-fifo-len = <24>;
+			fsl,exec-units-mask = <0xbfe>;
+			fsl,descriptor-types-mask = <0x3ab0ebf>;
+		};
+
+		mpic: pic@40000 {
+			interrupt-controller;
+			#address-cells = <0>;
+			#interrupt-cells = <2>;
+			reg = <0x40000 0x40000>;
+			compatible = "chrp,open-pic";
+			device_type = "open-pic";
+		};
+
+		msi@41600 {
+			compatible = "fsl,p1020-msi", "fsl,mpic-msi";
+			reg = <0x41600 0x80>;
+			msi-available-ranges = <0 0x100>;
+			interrupts = <
+				0xe0 0
+				0xe1 0
+				0xe2 0
+				0xe3 0
+				0xe4 0
+				0xe5 0
+				0xe6 0
+				0xe7 0>;
+			interrupt-parent = <&mpic>;
+		};
+
+		global-utilities@e0000 {	//global utilities block
+			compatible = "fsl,p1020-guts","fsl,p2020-guts";
+			reg = <0xe0000 0x1000>;
+			fsl,has-rstcr;
+		};
+	};
+
+	pci0: pcie@ffe09000 {
+		compatible = "fsl,mpc8548-pcie";
+		device_type = "pci";
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		reg = <0 0xffe09000 0 0x1000>;
+		bus-range = <0 255>;
+		clock-frequency = <33333333>;
+		interrupt-parent = <&mpic>;
+		interrupts = <16 2>;
+	};
+
+	pci1: pcie@ffe0a000 {
+		compatible = "fsl,mpc8548-pcie";
+		device_type = "pci";
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		reg = <0 0xffe0a000 0 0x1000>;
+		bus-range = <0 255>;
+		clock-frequency = <33333333>;
+		interrupt-parent = <&mpic>;
+		interrupts = <16 2>;
+	};
+};

arch/powerpc/boot/dts/p1022ds.dts

@@ -52,7 +52,7 @@ localbus@fffe05000 {
 		#size-cells = <1>;
 		compatible = "fsl,p1022-elbc", "fsl,elbc", "simple-bus";
 		reg = <0 0xffe05000 0 0x1000>;
-		interrupts = <19 2>;
+		interrupts = <19 2 0 0>;
 
 		ranges = <0x0 0x0 0xf 0xe8000000 0x08000000
 			  0x1 0x0 0xf 0xe0000000 0x08000000
@@ -157,7 +157,7 @@ board-control@3,0 {
 			 * IRQ8 is generated if the "EVENT" switch is pressed
 			 * and PX_CTL[EVESEL] is set to 00.
 			 */
-			interrupts = <8 8>;
+			interrupts = <8 8 0 0>;
 		};
 	};
 
@@ -178,13 +178,13 @@ ecm-law@0 {
 		ecm@1000 {
 			compatible = "fsl,p1022-ecm", "fsl,ecm";
 			reg = <0x1000 0x1000>;
-			interrupts = <16 2>;
+			interrupts = <16 2 0 0>;
 		};
 
 		memory-controller@2000 {
 			compatible = "fsl,p1022-memory-controller";
 			reg = <0x2000 0x1000>;
-			interrupts = <16 2>;
+			interrupts = <16 2 0 0>;
 		};
 
 		i2c@3000 {
@@ -193,7 +193,7 @@ i2c@3000 {
 			cell-index = <0>;
 			compatible = "fsl-i2c";
 			reg = <0x3000 0x100>;
-			interrupts = <43 2>;
+			interrupts = <43 2 0 0>;
 			dfsrr;
 		};
 
@@ -203,7 +203,7 @@ i2c@3100 {
 			cell-index = <1>;
 			compatible = "fsl-i2c";
 			reg = <0x3100 0x100>;
-			interrupts = <43 2>;
+			interrupts = <43 2 0 0>;
 			dfsrr;
 
 			wm8776:codec@1a {
@@ -220,7 +220,7 @@ serial0: serial@4500 {
 			compatible = "ns16550";
 			reg = <0x4500 0x100>;
 			clock-frequency = <0>;
-			interrupts = <42 2>;
+			interrupts = <42 2 0 0>;
 		};
 
 		serial1: serial@4600 {
@@ -229,7 +229,7 @@ serial1: serial@4600 {
 			compatible = "ns16550";
 			reg = <0x4600 0x100>;
 			clock-frequency = <0>;
-			interrupts = <42 2>;
+			interrupts = <42 2 0 0>;
 		};
 
 		spi@7000 {
@@ -238,7 +238,7 @@ spi@7000 {
 			#size-cells = <0>;
 			compatible = "fsl,espi";
 			reg = <0x7000 0x1000>;
-			interrupts = <59 0x2>;
+			interrupts = <59 0x2 0 0>;
 			espi,num-ss-bits = <4>;
 			mode = "cpu";
 
@@ -275,7 +275,7 @@ ssi@15000 {
 			compatible = "fsl,mpc8610-ssi";
 			cell-index = <0>;
 			reg = <0x15000 0x100>;
-			interrupts = <75 2>;
+			interrupts = <75 2 0 0>;
 			fsl,mode = "i2s-slave";
 			codec-handle = <&wm8776>;
 			fsl,playback-dma = <&dma00>;
@@ -294,25 +294,25 @@ dma00: dma-channel@0 {
 				compatible = "fsl,ssi-dma-channel";
 				reg = <0x0 0x80>;
 				cell-index = <0>;
-				interrupts = <76 2>;
+				interrupts = <76 2 0 0>;
 			};
 			dma01: dma-channel@80 {
 				compatible = "fsl,ssi-dma-channel";
 				reg = <0x80 0x80>;
 				cell-index = <1>;
-				interrupts = <77 2>;
+				interrupts = <77 2 0 0>;
 			};
 			dma-channel@100 {
 				compatible = "fsl,eloplus-dma-channel";
 				reg = <0x100 0x80>;
 				cell-index = <2>;
-				interrupts = <78 2>;
+				interrupts = <78 2 0 0>;
 			};
 			dma-channel@180 {
 				compatible = "fsl,eloplus-dma-channel";
 				reg = <0x180 0x80>;
 				cell-index = <3>;
-				interrupts = <79 2>;
+				interrupts = <79 2 0 0>;
 			};
 		};
 
@@ -320,7 +320,7 @@ gpio: gpio-controller@f000 {
 			#gpio-cells = <2>;
 			compatible = "fsl,mpc8572-gpio";
 			reg = <0xf000 0x100>;
-			interrupts = <47 0x2>;
+			interrupts = <47 0x2 0 0>;
 			gpio-controller;
 		};
 
@@ -329,7 +329,7 @@ L2: l2-cache-controller@20000 {
 			reg = <0x20000 0x1000>;
 			cache-line-size = <32>;	// 32 bytes
 			cache-size = <0x40000>; // L2, 256K
-			interrupts = <16 2>;
+			interrupts = <16 2 0 0>;
 		};
 
 		dma@21300 {
@@ -343,25 +343,25 @@ dma-channel@0 {
 				compatible = "fsl,eloplus-dma-channel";
 				reg = <0x0 0x80>;
 				cell-index = <0>;
-				interrupts = <20 2>;
+				interrupts = <20 2 0 0>;
 			};
 			dma-channel@80 {
 				compatible = "fsl,eloplus-dma-channel";
 				reg = <0x80 0x80>;
 				cell-index = <1>;
-				interrupts = <21 2>;
+				interrupts = <21 2 0 0>;
 			};
 			dma-channel@100 {
 				compatible = "fsl,eloplus-dma-channel";
 				reg = <0x100 0x80>;
 				cell-index = <2>;
-				interrupts = <22 2>;
+				interrupts = <22 2 0 0>;
 			};
 			dma-channel@180 {
 				compatible = "fsl,eloplus-dma-channel";
 				reg = <0x180 0x80>;
 				cell-index = <3>;
-				interrupts = <23 2>;
+				interrupts = <23 2 0 0>;
 			};
 		};
 
@@ -370,7 +370,7 @@ usb@22000 {
 			#size-cells = <0>;
 			compatible = "fsl-usb2-dr";
 			reg = <0x22000 0x1000>;
-			interrupts = <28 0x2>;
+			interrupts = <28 0x2 0 0>;
 			phy_type = "ulpi";
 		};
 
@@ -381,11 +381,11 @@ mdio@24000 {
 			reg = <0x24000 0x1000 0xb0030 0x4>;
 
 			phy0: ethernet-phy@0 {
-				interrupts = <3 1>;
+				interrupts = <3 1 0 0>;
 				reg = <0x1>;
 			};
 			phy1: ethernet-phy@1 {
-				interrupts = <9 1>;
+				interrupts = <9 1 0 0>;
 				reg = <0x2>;
 			};
 		};
@@ -416,13 +416,13 @@ queue-group@0{
 				#address-cells = <1>;
 				#size-cells = <1>;
 				reg = <0xB0000 0x1000>;
-				interrupts = <29 2 30 2 34 2>;
+				interrupts = <29 2 0 0 30 2 0 0 34 2 0 0>;
 			};
 			queue-group@1{
 				#address-cells = <1>;
 				#size-cells = <1>;
 				reg = <0xB4000 0x1000>;
-				interrupts = <17 2 18 2 24 2>;
+				interrupts = <17 2 0 0 18 2 0 0 24 2 0 0>;
 			};
 		};
 
@@ -443,20 +443,20 @@ queue-group@0{
 				#address-cells = <1>;
 				#size-cells = <1>;
 				reg = <0xB1000 0x1000>;
-				interrupts = <35 2 36 2 40 2>;
+				interrupts = <35 2 0 0 36 2 0 0 40 2 0 0>;
 			};
 			queue-group@1{
 				#address-cells = <1>;
 				#size-cells = <1>;
 				reg = <0xB5000 0x1000>;
-				interrupts = <51 2 52 2 67 2>;
+				interrupts = <51 2 0 0 52 2 0 0 67 2 0 0>;
 			};
 		};
 
 		sdhci@2e000 {
 			compatible = "fsl,p1022-esdhc", "fsl,esdhc";
 			reg = <0x2e000 0x1000>;
-			interrupts = <72 0x2>;
+			interrupts = <72 0x2 0 0>;
 			fsl,sdhci-auto-cmd12;
 			/* Filled in by U-Boot */
 			clock-frequency = <0>;
@@ -467,7 +467,7 @@ crypto@30000 {
 				     "fsl,sec2.4", "fsl,sec2.2", "fsl,sec2.1",
 				     "fsl,sec2.0";
 			reg = <0x30000 0x10000>;
-			interrupts = <45 2 58 2>;
+			interrupts = <45 2 0 0 58 2 0 0>;
 			fsl,num-channels = <4>;
 			fsl,channel-fifo-len = <24>;
 			fsl,exec-units-mask = <0x97c>;
@@ -478,14 +478,14 @@ sata@18000 {
 			compatible = "fsl,p1022-sata", "fsl,pq-sata-v2";
 			reg = <0x18000 0x1000>;
 			cell-index = <1>;
-			interrupts = <74 0x2>;
+			interrupts = <74 0x2 0 0>;
 		};
 
 		sata@19000 {
 			compatible = "fsl,p1022-sata", "fsl,pq-sata-v2";
 			reg = <0x19000 0x1000>;
 			cell-index = <2>;
-			interrupts = <41 0x2>;
+			interrupts = <41 0x2 0 0>;
 		};
 
 		power@e0070{
@@ -496,21 +496,33 @@ power@e0070{
 		display@10000 {
 			compatible = "fsl,diu", "fsl,p1022-diu";
 			reg = <0x10000 1000>;
-			interrupts = <64 2>;
+			interrupts = <64 2 0 0>;
 		};
 
 		timer@41100 {
 			compatible = "fsl,mpic-global-timer";
-			reg = <0x41100 0x204>;
-			interrupts = <0xf7 0x2>;
+			reg = <0x41100 0x100 0x41300 4>;
+			interrupts = <0 0 3 0
+			              1 0 3 0
+			              2 0 3 0
+			              3 0 3 0>;
+		};
+
+		timer@42100 {
+			compatible = "fsl,mpic-global-timer";
+			reg = <0x42100 0x100 0x42300 4>;
+			interrupts = <4 0 3 0
+			              5 0 3 0
+			              6 0 3 0
+			              7 0 3 0>;
 		};
 
 		mpic: pic@40000 {
 			interrupt-controller;
 			#address-cells = <0>;
-			#interrupt-cells = <2>;
+			#interrupt-cells = <4>;
 			reg = <0x40000 0x40000>;
-			compatible = "chrp,open-pic";
+			compatible = "fsl,mpic";
 			device_type = "open-pic";
 		};
 
@@ -519,14 +531,14 @@ msi@41600 {
 			reg = <0x41600 0x80>;
 			msi-available-ranges = <0 0x100>;
 			interrupts = <
-				0xe0 0
-				0xe1 0
-				0xe2 0
-				0xe3 0
-				0xe4 0
-				0xe5 0
-				0xe6 0
-				0xe7 0>;
+				0xe0 0 0 0
+				0xe1 0 0 0
+				0xe2 0 0 0
+				0xe3 0 0 0
+				0xe4 0 0 0
+				0xe5 0 0 0
+				0xe6 0 0 0
+				0xe7 0 0 0>;
 		};
 
 		global-utilities@e0000 {	//global utilities block
@@ -547,7 +559,7 @@ pci0: pcie@fffe09000 {
 		ranges = <0x2000000 0x0 0xa0000000 0xc 0x20000000 0x0 0x20000000
 			  0x1000000 0x0 0x00000000 0xf 0xffc10000 0x0 0x10000>;
 		clock-frequency = <33333333>;
-		interrupts = <16 2>;
+		interrupts = <16 2 0 0>;
 		interrupt-map-mask = <0xf800 0 0 7>;
 		interrupt-map = <
 			/* IDSEL 0x0 */
@@ -582,7 +594,7 @@ pci1: pcie@fffe0a000 {
 		ranges = <0x2000000 0x0 0xc0000000 0xc 0x40000000 0x0 0x20000000
 			  0x1000000 0x0 0x00000000 0xf 0xffc20000 0x0 0x10000>;
 		clock-frequency = <33333333>;
-		interrupts = <16 2>;
+		interrupts = <16 2 0 0>;
 		interrupt-map-mask = <0xf800 0 0 7>;
 		interrupt-map = <
 			/* IDSEL 0x0 */
@@ -618,7 +630,7 @@ pci2: pcie@fffe0b000 {
 		ranges = <0x2000000 0x0 0x80000000 0xc 0x00000000 0x0 0x20000000
 			  0x1000000 0x0 0x00000000 0xf 0xffc00000 0x0 0x10000>;
 		clock-frequency = <33333333>;
-		interrupts = <16 2>;
+		interrupts = <16 2 0 0>;
 		interrupt-map-mask = <0xf800 0 0 7>;
 		interrupt-map = <
 			/* IDSEL 0x0 */

arch/powerpc/boot/dts/p2020rdb_camp_core0.dts

@@ -14,12 +14,11 @@
  * option) any later version.
  */
 
-/dts-v1/;
+/include/ "p2020si.dtsi"
+
 / {
-	model = "fsl,P2020";
+	model = "fsl,P2020RDB";
 	compatible = "fsl,P2020RDB", "fsl,MPC85XXRDB-CAMP";
-	#address-cells = <2>;
-	#size-cells = <2>;
 
 	aliases {
 		ethernet1 = &enet1;
@@ -29,91 +28,33 @@ aliases {
 	};
 
 	cpus {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		PowerPC,P2020@0 {
-			device_type = "cpu";
-			reg = <0x0>;
-			next-level-cache = <&L2>;
+		PowerPC,P2020@1 {
+		status = "disabled";
 		};
+
 	};
 
 	memory {
 		device_type = "memory";
 	};
 
-	soc@ffe00000 {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		device_type = "soc";
-		compatible = "fsl,p2020-immr", "simple-bus";
-		ranges = <0x0  0x0 0xffe00000 0x100000>;
-		bus-frequency = <0>;		// Filled out by uboot.
-
-		ecm-law@0 {
-			compatible = "fsl,ecm-law";
-			reg = <0x0 0x1000>;
-			fsl,num-laws = <12>;
-		};
-
-		ecm@1000 {
-			compatible = "fsl,p2020-ecm", "fsl,ecm";
-			reg = <0x1000 0x1000>;
-			interrupts = <17 2>;
-			interrupt-parent = <&mpic>;
-		};
-
-		memory-controller@2000 {
-			compatible = "fsl,p2020-memory-controller";
-			reg = <0x2000 0x1000>;
-			interrupt-parent = <&mpic>;
-			interrupts = <18 2>;
-		};
+	localbus@ffe05000 {
+		status = "disabled";
+	};
 
+	soc@ffe00000 {
 		i2c@3000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			cell-index = <0>;
-			compatible = "fsl-i2c";
-			reg = <0x3000 0x100>;
-			interrupts = <43 2>;
-			interrupt-parent = <&mpic>;
-			dfsrr;
 			rtc@68 {
 				compatible = "dallas,ds1339";
 				reg = <0x68>;
 			};
 		};
 
-		i2c@3100 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			cell-index = <1>;
-			compatible = "fsl-i2c";
-			reg = <0x3100 0x100>;
-			interrupts = <43 2>;
-			interrupt-parent = <&mpic>;
-			dfsrr;
-		};
-
-		serial0: serial@4500 {
-			cell-index = <0>;
-			device_type = "serial";
-			compatible = "ns16550";
-			reg = <0x4500 0x100>;
-			clock-frequency = <0>;
+		serial1: serial@4600 {
+			status = "disabled";
 		};
 
 		spi@7000 {
-			cell-index = <0>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "fsl,espi";
-			reg = <0x7000 0x1000>;
-			interrupts = <59 0x2>;
-			interrupt-parent = <&mpic>;
-			mode = "cpu";
 
 			fsl_m25p80@0 {
 				#address-cells = <1>;
@@ -161,76 +102,15 @@ partition@900000 {
 			};
 		};
 
-		gpio: gpio-controller@f000 {
-			#gpio-cells = <2>;
-			compatible = "fsl,mpc8572-gpio";
-			reg = <0xf000 0x100>;
-			interrupts = <47 0x2>;
-			interrupt-parent = <&mpic>;
-			gpio-controller;
-		};
-
-		L2: l2-cache-controller@20000 {
-			compatible = "fsl,p2020-l2-cache-controller";
-			reg = <0x20000 0x1000>;
-			cache-line-size = <32>;	// 32 bytes
-			cache-size = <0x80000>; // L2,512K
-			interrupt-parent = <&mpic>;
-			interrupts = <16 2>;
-		};
-
-		dma@21300 {
-			#address-cells = <1>;
-			#size-cells = <1>;
-			compatible = "fsl,eloplus-dma";
-			reg = <0x21300 0x4>;
-			ranges = <0x0 0x21100 0x200>;
-			cell-index = <0>;
-			dma-channel@0 {
-				compatible = "fsl,eloplus-dma-channel";
-				reg = <0x0 0x80>;
-				cell-index = <0>;
-				interrupt-parent = <&mpic>;
-				interrupts = <20 2>;
-			};
-			dma-channel@80 {
-				compatible = "fsl,eloplus-dma-channel";
-				reg = <0x80 0x80>;
-				cell-index = <1>;
-				interrupt-parent = <&mpic>;
-				interrupts = <21 2>;
-			};
-			dma-channel@100 {
-				compatible = "fsl,eloplus-dma-channel";
-				reg = <0x100 0x80>;
-				cell-index = <2>;
-				interrupt-parent = <&mpic>;
-				interrupts = <22 2>;
-			};
-			dma-channel@180 {
-				compatible = "fsl,eloplus-dma-channel";
-				reg = <0x180 0x80>;
-				cell-index = <3>;
-				interrupt-parent = <&mpic>;
-				interrupts = <23 2>;
-			};
+		dma@c300 {
+			status = "disabled";
 		};
 
 		usb@22000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "fsl-usb2-dr";
-			reg = <0x22000 0x1000>;
-			interrupt-parent = <&mpic>;
-			interrupts = <28 0x2>;
 			phy_type = "ulpi";
 		};
 
 		mdio@24520 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "fsl,gianfar-mdio";
-			reg = <0x24520 0x20>;
 
 			phy0: ethernet-phy@0 {
 				interrupt-parent = <&mpic>;
@@ -245,29 +125,21 @@ phy1: ethernet-phy@1 {
 		};
 
 		mdio@25520 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "fsl,gianfar-tbi";
-			reg = <0x26520 0x20>;
-
 			tbi0: tbi-phy@11 {
 				reg = <0x11>;
 				device_type = "tbi-phy";
 			};
 		};
 
+		mdio@26520 {
+			status = "disabled";
+		};
+
+		enet0: ethernet@24000 {
+			status = "disabled";
+		};
+
 		enet1: ethernet@25000 {
-			#address-cells = <1>;
-			#size-cells = <1>;
-			cell-index = <1>;
-			device_type = "network";
-			model = "eTSEC";
-			compatible = "gianfar";
-			reg = <0x25000 0x1000>;
-			ranges = <0x0 0x25000 0x1000>;
-			local-mac-address = [ 00 00 00 00 00 00 ];
-			interrupts = <35 2 36 2 40 2>;
-			interrupt-parent = <&mpic>;
 			tbi-handle = <&tbi0>;
 			phy-handle = <&phy0>;
 			phy-connection-type = "sgmii";
@@ -275,49 +147,12 @@ enet1: ethernet@25000 {
 		};
 
 		enet2: ethernet@26000 {
-			#address-cells = <1>;
-			#size-cells = <1>;
-			cell-index = <2>;
-			device_type = "network";
-			model = "eTSEC";
-			compatible = "gianfar";
-			reg = <0x26000 0x1000>;
-			ranges = <0x0 0x26000 0x1000>;
-			local-mac-address = [ 00 00 00 00 00 00 ];
-			interrupts = <31 2 32 2 33 2>;
-			interrupt-parent = <&mpic>;
 			phy-handle = <&phy1>;
 			phy-connection-type = "rgmii-id";
 		};
 
-		sdhci@2e000 {
-			compatible = "fsl,p2020-esdhc", "fsl,esdhc";
-			reg = <0x2e000 0x1000>;
-			interrupts = <72 0x2>;
-			interrupt-parent = <&mpic>;
-			/* Filled in by U-Boot */
-			clock-frequency = <0>;
-		};
-
-		crypto@30000 {
-			compatible = "fsl,sec3.1", "fsl,sec3.0", "fsl,sec2.4",
-				     "fsl,sec2.2", "fsl,sec2.1", "fsl,sec2.0";
-			reg = <0x30000 0x10000>;
-			interrupts = <45 2 58 2>;
-			interrupt-parent = <&mpic>;
-			fsl,num-channels = <4>;
-			fsl,channel-fifo-len = <24>;
-			fsl,exec-units-mask = <0xbfe>;
-			fsl,descriptor-types-mask = <0x3ab0ebf>;
-		};
 
 		mpic: pic@40000 {
-			interrupt-controller;
-			#address-cells = <0>;
-			#interrupt-cells = <2>;
-			reg = <0x40000 0x40000>;
-			compatible = "chrp,open-pic";
-			device_type = "open-pic";
 			protected-sources = <
 			42 76 77 78 79 /* serial1 , dma2 */
 			29 30 34 26 /* enet0, pci1 */
@@ -326,26 +161,28 @@ mpic: pic@40000 {
 			>;
 		};
 
-		global-utilities@e0000 {
-			compatible = "fsl,p2020-guts";
-			reg = <0xe0000 0x1000>;
-			fsl,has-rstcr;
+		msi@41600 {
+			status = "disabled";
 		};
+
+
 	};
 
-	pci0: pcie@ffe09000 {
-		compatible = "fsl,mpc8548-pcie";
-		device_type = "pci";
-		#interrupt-cells = <1>;
-		#size-cells = <2>;
-		#address-cells = <3>;
-		reg = <0 0xffe09000 0 0x1000>;
-		bus-range = <0 255>;
+	pci0: pcie@ffe08000 {
+		status = "disabled";
+	};
+
+	pci1: pcie@ffe09000 {
 		ranges = <0x2000000 0x0 0xa0000000 0 0xa0000000 0x0 0x20000000
 			  0x1000000 0x0 0x00000000 0 0xffc10000 0x0 0x10000>;
-		clock-frequency = <33333333>;
-		interrupt-parent = <&mpic>;
-		interrupts = <25 2>;
+		interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
+		interrupt-map = <
+			/* IDSEL 0x0 */
+			0000 0x0 0x0 0x1 &mpic 0x4 0x1
+			0000 0x0 0x0 0x2 &mpic 0x5 0x1
+			0000 0x0 0x0 0x3 &mpic 0x6 0x1
+			0000 0x0 0x0 0x4 &mpic 0x7 0x1
+			>;
 		pcie@0 {
 			reg = <0x0 0x0 0x0 0x0 0x0>;
 			#size-cells = <2>;
@@ -360,4 +197,8 @@ pcie@0 {
 				  0x0 0x100000>;
 		};
 	};
+
+	pci2: pcie@ffe0a000 {
+		status = "disabled";
+	};
 };

arch/powerpc/boot/dts/p2020rdb_camp_core1.dts

@@ -15,27 +15,21 @@
  * option) any later version.
  */
 
-/dts-v1/;
+/include/ "p2020si.dtsi"
+
 / {
-	model = "fsl,P2020";
+	model = "fsl,P2020RDB";
 	compatible = "fsl,P2020RDB", "fsl,MPC85XXRDB-CAMP";
-	#address-cells = <2>;
-	#size-cells = <2>;
 
 	aliases {
 		ethernet0 = &enet0;
-		serial0 = &serial0;
+		serial0 = &serial1;
 		pci1 = &pci1;
 	};
 
 	cpus {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		PowerPC,P2020@1 {
-			device_type = "cpu";
-			reg = <0x1>;
-			next-level-cache = <&L2>;
+		PowerPC,P2020@0 {
+		status = "disabled";
 		};
 	};
 
@@ -43,20 +37,37 @@ memory {
 		device_type = "memory";
 	};
 
+	localbus@ffe05000 {
+		status = "disabled";
+	};
+
 	soc@ffe00000 {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		device_type = "soc";
-		compatible = "fsl,p2020-immr", "simple-bus";
-		ranges = <0x0  0x0 0xffe00000 0x100000>;
-		bus-frequency = <0>;		// Filled out by uboot.
-
-		serial0: serial@4600 {
-			cell-index = <1>;
-			device_type = "serial";
-			compatible = "ns16550";
-			reg = <0x4600 0x100>;
-			clock-frequency = <0>;
+		ecm-law@0 {
+			status = "disabled";
+		};
+
+		ecm@1000 {
+			status = "disabled";
+		};
+
+		memory-controller@2000 {
+			status = "disabled";
+		};
+
+		i2c@3000 {
+			status = "disabled";
+		};
+
+		i2c@3100 {
+			status = "disabled";
+		};
+
+		serial0: serial@4500 {
+			status = "disabled";
+		};
+
+		spi@7000 {
+			status = "disabled";
 		};
 
 		dma@c300 {
@@ -96,6 +107,10 @@ dma-channel@180 {
 			};
 		};
 
+		gpio: gpio-controller@f000 {
+			status = "disabled";
+		};
+
 		L2: l2-cache-controller@20000 {
 			compatible = "fsl,p2020-l2-cache-controller";
 			reg = <0x20000 0x1000>;
@@ -104,31 +119,49 @@ L2: l2-cache-controller@20000 {
 			interrupt-parent = <&mpic>;
 		};
 
+		dma@21300 {
+			status = "disabled";
+		};
+
+		usb@22000 {
+			status = "disabled";
+		};
+
+		mdio@24520 {
+			status = "disabled";
+		};
+
+		mdio@25520 {
+			status = "disabled";
+		};
+
+		mdio@26520 {
+			status = "disabled";
+		};
 
 		enet0: ethernet@24000 {
-			#address-cells = <1>;
-			#size-cells = <1>;
-			cell-index = <0>;
-			device_type = "network";
-			model = "eTSEC";
-			compatible = "gianfar";
-			reg = <0x24000 0x1000>;
-			ranges = <0x0 0x24000 0x1000>;
-			local-mac-address = [ 00 00 00 00 00 00 ];
-			interrupts = <29 2 30 2 34 2>;
-			interrupt-parent = <&mpic>;
 			fixed-link = <1 1 1000 0 0>;
 			phy-connection-type = "rgmii-id";
 
 		};
 
+		enet1: ethernet@25000 {
+			status = "disabled";
+		};
+
+		enet2: ethernet@26000 {
+			status = "disabled";
+		};
+
+		sdhci@2e000 {
+			status = "disabled";
+		};
+
+		crypto@30000 {
+			status = "disabled";
+		};
+
 		mpic: pic@40000 {
-			interrupt-controller;
-			#address-cells = <0>;
-			#interrupt-cells = <2>;
-			reg = <0x40000 0x40000>;
-			compatible = "chrp,open-pic";
-			device_type = "open-pic";
 			protected-sources = <
 			17 18 43 42 59 47 /*ecm, mem, i2c, serial0, spi,gpio */
 			16 20 21 22 23 28 	/* L2, dma1, USB */
@@ -152,21 +185,32 @@ msi@41600 {
 				0xe7 0>;
 			interrupt-parent = <&mpic>;
 		};
+
+		global-utilities@e0000 {	//global utilities block
+			status = "disabled";
+		};
+
 	};
 
-	pci1: pcie@ffe0a000 {
-		compatible = "fsl,mpc8548-pcie";
-		device_type = "pci";
-		#interrupt-cells = <1>;
-		#size-cells = <2>;
-		#address-cells = <3>;
-		reg = <0 0xffe0a000 0 0x1000>;
-		bus-range = <0 255>;
+	pci0: pcie@ffe08000 {
+		status = "disabled";
+	};
+
+	pci1: pcie@ffe09000 {
+		status = "disabled";
+	};
+
+	pci2: pcie@ffe0a000 {
 		ranges = <0x2000000 0x0 0x80000000 0 0x80000000 0x0 0x20000000
 			  0x1000000 0x0 0x00000000 0 0xffc00000 0x0 0x10000>;
-		clock-frequency = <33333333>;
-		interrupt-parent = <&mpic>;
-		interrupts = <26 2>;
+		interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
+		interrupt-map = <
+			/* IDSEL 0x0 */
+			0000 0x0 0x0 0x1 &mpic 0x0 0x1
+			0000 0x0 0x0 0x2 &mpic 0x1 0x1
+			0000 0x0 0x0 0x3 &mpic 0x2 0x1
+			0000 0x0 0x0 0x4 &mpic 0x3 0x1
+			>;
 		pcie@0 {
 			reg = <0x0 0x0 0x0 0x0 0x0>;
 			#size-cells = <2>;

arch/powerpc/boot/dts/p2020si.dtsi

+/*
+ * P2020 Device Tree Source
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+/dts-v1/;
+/ {
+	compatible = "fsl,P2020";
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		PowerPC,P2020@0 {
+			device_type = "cpu";
+			reg = <0x0>;
+			next-level-cache = <&L2>;
+		};
+
+		PowerPC,P2020@1 {
+			device_type = "cpu";
+			reg = <0x1>;
+			next-level-cache = <&L2>;
+		};
+	};
+
+	localbus@ffe05000 {
+		#address-cells = <2>;
+		#size-cells = <1>;
+		compatible = "fsl,p2020-elbc", "fsl,elbc", "simple-bus";
+		reg = <0 0xffe05000 0 0x1000>;
+		interrupts = <19 2>;
+		interrupt-parent = <&mpic>;
+	};
+
+	soc@ffe00000 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		device_type = "soc";
+		compatible = "fsl,p2020-immr", "simple-bus";
+		ranges = <0x0  0x0 0xffe00000 0x100000>;
+		bus-frequency = <0>;		// Filled out by uboot.
+
+		ecm-law@0 {
+			compatible = "fsl,ecm-law";
+			reg = <0x0 0x1000>;
+			fsl,num-laws = <12>;
+		};
+
+		ecm@1000 {
+			compatible = "fsl,p2020-ecm", "fsl,ecm";
+			reg = <0x1000 0x1000>;
+			interrupts = <17 2>;
+			interrupt-parent = <&mpic>;
+		};
+
+		memory-controller@2000 {
+			compatible = "fsl,p2020-memory-controller";
+			reg = <0x2000 0x1000>;
+			interrupt-parent = <&mpic>;
+			interrupts = <18 2>;
+		};
+
+		i2c@3000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			cell-index = <0>;
+			compatible = "fsl-i2c";
+			reg = <0x3000 0x100>;
+			interrupts = <43 2>;
+			interrupt-parent = <&mpic>;
+			dfsrr;
+		};
+
+		i2c@3100 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			cell-index = <1>;
+			compatible = "fsl-i2c";
+			reg = <0x3100 0x100>;
+			interrupts = <43 2>;
+			interrupt-parent = <&mpic>;
+			dfsrr;
+		};
+
+		serial0: serial@4500 {
+			cell-index = <0>;
+			device_type = "serial";
+			compatible = "ns16550";
+			reg = <0x4500 0x100>;
+			clock-frequency = <0>;
+			interrupts = <42 2>;
+			interrupt-parent = <&mpic>;
+		};
+
+		serial1: serial@4600 {
+			cell-index = <1>;
+			device_type = "serial";
+			compatible = "ns16550";
+			reg = <0x4600 0x100>;
+			clock-frequency = <0>;
+			interrupts = <42 2>;
+			interrupt-parent = <&mpic>;
+		};
+
+		spi@7000 {
+			cell-index = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "fsl,espi";
+			reg = <0x7000 0x1000>;
+			interrupts = <59 0x2>;
+			interrupt-parent = <&mpic>;
+			mode = "cpu";
+		};
+
+		dma@c300 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "fsl,eloplus-dma";
+			reg = <0xc300 0x4>;
+			ranges = <0x0 0xc100 0x200>;
+			cell-index = <1>;
+			dma-channel@0 {
+				compatible = "fsl,eloplus-dma-channel";
+				reg = <0x0 0x80>;
+				cell-index = <0>;
+				interrupt-parent = <&mpic>;
+				interrupts = <76 2>;
+			};
+			dma-channel@80 {
+				compatible = "fsl,eloplus-dma-channel";
+				reg = <0x80 0x80>;
+				cell-index = <1>;
+				interrupt-parent = <&mpic>;
+				interrupts = <77 2>;
+			};
+			dma-channel@100 {
+				compatible = "fsl,eloplus-dma-channel";
+				reg = <0x100 0x80>;
+				cell-index = <2>;
+				interrupt-parent = <&mpic>;
+				interrupts = <78 2>;
+			};
+			dma-channel@180 {
+				compatible = "fsl,eloplus-dma-channel";
+				reg = <0x180 0x80>;
+				cell-index = <3>;
+				interrupt-parent = <&mpic>;
+				interrupts = <79 2>;
+			};
+		};
+
+		gpio: gpio-controller@f000 {
+			#gpio-cells = <2>;
+			compatible = "fsl,mpc8572-gpio";
+			reg = <0xf000 0x100>;
+			interrupts = <47 0x2>;
+			interrupt-parent = <&mpic>;
+			gpio-controller;
+		};
+
+		L2: l2-cache-controller@20000 {
+			compatible = "fsl,p2020-l2-cache-controller";
+			reg = <0x20000 0x1000>;
+			cache-line-size = <32>;	// 32 bytes
+			cache-size = <0x80000>; // L2,512K
+			interrupt-parent = <&mpic>;
+			interrupts = <16 2>;
+		};
+
+		dma@21300 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "fsl,eloplus-dma";
+			reg = <0x21300 0x4>;
+			ranges = <0x0 0x21100 0x200>;
+			cell-index = <0>;
+			dma-channel@0 {
+				compatible = "fsl,eloplus-dma-channel";
+				reg = <0x0 0x80>;
+				cell-index = <0>;
+				interrupt-parent = <&mpic>;
+				interrupts = <20 2>;
+			};
+			dma-channel@80 {
+				compatible = "fsl,eloplus-dma-channel";
+				reg = <0x80 0x80>;
+				cell-index = <1>;
+				interrupt-parent = <&mpic>;
+				interrupts = <21 2>;
+			};
+			dma-channel@100 {
+				compatible = "fsl,eloplus-dma-channel";
+				reg = <0x100 0x80>;
+				cell-index = <2>;
+				interrupt-parent = <&mpic>;
+				interrupts = <22 2>;
+			};
+			dma-channel@180 {
+				compatible = "fsl,eloplus-dma-channel";
+				reg = <0x180 0x80>;
+				cell-index = <3>;
+				interrupt-parent = <&mpic>;
+				interrupts = <23 2>;
+			};
+		};
+
+		usb@22000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "fsl-usb2-dr";
+			reg = <0x22000 0x1000>;
+			interrupt-parent = <&mpic>;
+			interrupts = <28 0x2>;
+		};
+
+		mdio@24520 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "fsl,gianfar-mdio";
+			reg = <0x24520 0x20>;
+		};
+
+		mdio@25520 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "fsl,gianfar-tbi";
+			reg = <0x26520 0x20>;
+		};
+
+		mdio@26520 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "fsl,gianfar-tbi";
+			reg = <0x520 0x20>;
+		};
+
+		enet0: ethernet@24000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			cell-index = <0>;
+			device_type = "network";
+			model = "eTSEC";
+			compatible = "gianfar";
+			reg = <0x24000 0x1000>;
+			ranges = <0x0 0x24000 0x1000>;
+			local-mac-address = [ 00 00 00 00 00 00 ];
+			interrupts = <29 2 30 2 34 2>;
+			interrupt-parent = <&mpic>;
+		};
+
+		enet1: ethernet@25000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			cell-index = <1>;
+			device_type = "network";
+			model = "eTSEC";
+			compatible = "gianfar";
+			reg = <0x25000 0x1000>;
+			ranges = <0x0 0x25000 0x1000>;
+			local-mac-address = [ 00 00 00 00 00 00 ];
+			interrupts = <35 2 36 2 40 2>;
+			interrupt-parent = <&mpic>;
+
+		};
+
+		enet2: ethernet@26000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			cell-index = <2>;
+			device_type = "network";
+			model = "eTSEC";
+			compatible = "gianfar";
+			reg = <0x26000 0x1000>;
+			ranges = <0x0 0x26000 0x1000>;
+			local-mac-address = [ 00 00 00 00 00 00 ];
+			interrupts = <31 2 32 2 33 2>;
+			interrupt-parent = <&mpic>;
+
+		};
+
+		sdhci@2e000 {
+			compatible = "fsl,p2020-esdhc", "fsl,esdhc";
+			reg = <0x2e000 0x1000>;
+			interrupts = <72 0x2>;
+			interrupt-parent = <&mpic>;
+			/* Filled in by U-Boot */
+			clock-frequency = <0>;
+		};
+
+		crypto@30000 {
+			compatible = "fsl,sec3.1", "fsl,sec3.0", "fsl,sec2.4",
+				     "fsl,sec2.2", "fsl,sec2.1", "fsl,sec2.0";
+			reg = <0x30000 0x10000>;
+			interrupts = <45 2 58 2>;
+			interrupt-parent = <&mpic>;
+			fsl,num-channels = <4>;
+			fsl,channel-fifo-len = <24>;
+			fsl,exec-units-mask = <0xbfe>;
+			fsl,descriptor-types-mask = <0x3ab0ebf>;
+		};
+
+		mpic: pic@40000 {
+			interrupt-controller;
+			#address-cells = <0>;
+			#interrupt-cells = <2>;
+			reg = <0x40000 0x40000>;
+			compatible = "chrp,open-pic";
+			device_type = "open-pic";
+		};
+
+		msi@41600 {
+			compatible = "fsl,p2020-msi", "fsl,mpic-msi";
+			reg = <0x41600 0x80>;
+			msi-available-ranges = <0 0x100>;
+			interrupts = <
+				0xe0 0
+				0xe1 0
+				0xe2 0
+				0xe3 0
+				0xe4 0
+				0xe5 0
+				0xe6 0
+				0xe7 0>;
+			interrupt-parent = <&mpic>;
+		};
+
+		global-utilities@e0000 {	//global utilities block
+			compatible = "fsl,p2020-guts";
+			reg = <0xe0000 0x1000>;
+			fsl,has-rstcr;
+		};
+	};
+
+	pci0: pcie@ffe08000 {
+		compatible = "fsl,mpc8548-pcie";
+		device_type = "pci";
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		reg = <0 0xffe08000 0 0x1000>;
+		bus-range = <0 255>;
+		clock-frequency = <33333333>;
+		interrupt-parent = <&mpic>;
+		interrupts = <24 2>;
+	};
+
+	pci1: pcie@ffe09000 {
+		compatible = "fsl,mpc8548-pcie";
+		device_type = "pci";
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		reg = <0 0xffe09000 0 0x1000>;
+		bus-range = <0 255>;
+		clock-frequency = <33333333>;
+		interrupt-parent = <&mpic>;
+		interrupts = <25 2>;
+	};
+
+	pci2: pcie@ffe0a000 {
+		compatible = "fsl,mpc8548-pcie";
+		device_type = "pci";
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		reg = <0 0xffe0a000 0 0x1000>;
+		bus-range = <0 255>;
+		clock-frequency = <33333333>;
+		interrupt-parent = <&mpic>;
+		interrupts = <26 2>;
+	};
+};

arch/powerpc/configs/83xx/mpc8313_rdb_defconfig

@@ -104,7 +104,6 @@ CONFIG_ROOT_NFS=y
 CONFIG_PARTITION_ADVANCED=y
 CONFIG_DEBUG_KERNEL=y
 CONFIG_DETECT_HUNG_TASK=y
-# CONFIG_DEBUG_BUGVERBOSE is not set
 # CONFIG_RCU_CPU_STALL_DETECTOR is not set
 CONFIG_SYSCTL_SYSCALL_CHECK=y
 CONFIG_CRYPTO_PCBC=m

arch/powerpc/configs/83xx/mpc8315_rdb_defconfig

@@ -101,7 +101,6 @@ CONFIG_ROOT_NFS=y
 CONFIG_PARTITION_ADVANCED=y
 CONFIG_DEBUG_KERNEL=y
 CONFIG_DETECT_HUNG_TASK=y
-# CONFIG_DEBUG_BUGVERBOSE is not set
 # CONFIG_RCU_CPU_STALL_DETECTOR is not set
 CONFIG_SYSCTL_SYSCALL_CHECK=y
 CONFIG_CRYPTO_PCBC=m

arch/powerpc/configs/85xx/mpc8540_ads_defconfig

@@ -58,7 +58,6 @@ CONFIG_PARTITION_ADVANCED=y
 CONFIG_DEBUG_KERNEL=y
 CONFIG_DETECT_HUNG_TASK=y
 CONFIG_DEBUG_MUTEXES=y
-# CONFIG_DEBUG_BUGVERBOSE is not set
 # CONFIG_RCU_CPU_STALL_DETECTOR is not set
 CONFIG_SYSCTL_SYSCALL_CHECK=y
 # CONFIG_CRYPTO_ANSI_CPRNG is not set

arch/powerpc/configs/85xx/mpc8560_ads_defconfig

@@ -59,7 +59,6 @@ CONFIG_PARTITION_ADVANCED=y
 CONFIG_DEBUG_KERNEL=y
 CONFIG_DETECT_HUNG_TASK=y
 CONFIG_DEBUG_MUTEXES=y
-# CONFIG_DEBUG_BUGVERBOSE is not set
 # CONFIG_RCU_CPU_STALL_DETECTOR is not set
 CONFIG_SYSCTL_SYSCALL_CHECK=y
 # CONFIG_CRYPTO_ANSI_CPRNG is not set

arch/powerpc/configs/85xx/mpc85xx_cds_defconfig

@@ -63,7 +63,6 @@ CONFIG_PARTITION_ADVANCED=y
 CONFIG_DEBUG_KERNEL=y
 CONFIG_DETECT_HUNG_TASK=y
 CONFIG_DEBUG_MUTEXES=y
-# CONFIG_DEBUG_BUGVERBOSE is not set
 # CONFIG_RCU_CPU_STALL_DETECTOR is not set
 CONFIG_SYSCTL_SYSCALL_CHECK=y
 # CONFIG_CRYPTO_ANSI_CPRNG is not set

arch/powerpc/configs/86xx/mpc8641_hpcn_defconfig

@@ -168,7 +168,6 @@ CONFIG_MAC_PARTITION=y
 CONFIG_CRC_T10DIF=y
 CONFIG_DEBUG_KERNEL=y
 CONFIG_DETECT_HUNG_TASK=y
-# CONFIG_DEBUG_BUGVERBOSE is not set
 CONFIG_DEBUG_INFO=y
 # CONFIG_RCU_CPU_STALL_DETECTOR is not set
 CONFIG_SYSCTL_SYSCALL_CHECK=y

arch/powerpc/configs/e55xx_smp_defconfig

@@ -6,10 +6,10 @@ CONFIG_NR_CPUS=2
 CONFIG_EXPERIMENTAL=y
 CONFIG_SYSVIPC=y
 CONFIG_BSD_PROCESS_ACCT=y
+CONFIG_SPARSE_IRQ=y
 CONFIG_IKCONFIG=y
 CONFIG_IKCONFIG_PROC=y
 CONFIG_LOG_BUF_SHIFT=14
-CONFIG_SYSFS_DEPRECATED_V2=y
 CONFIG_BLK_DEV_INITRD=y
 # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
 CONFIG_EXPERT=y
@@ -25,8 +25,32 @@ CONFIG_P5020_DS=y
 CONFIG_NO_HZ=y
 CONFIG_HIGH_RES_TIMERS=y
 CONFIG_BINFMT_MISC=m
-CONFIG_SPARSE_IRQ=y
 # CONFIG_PCI is not set
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_XFRM_USER=y
+CONFIG_NET_KEY=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_ADVANCED_ROUTER=y
+CONFIG_IP_MULTIPLE_TABLES=y
+CONFIG_IP_ROUTE_MULTIPATH=y
+CONFIG_IP_ROUTE_VERBOSE=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_IP_PNP_RARP=y
+CONFIG_NET_IPIP=y
+CONFIG_IP_MROUTE=y
+CONFIG_IP_PIMSM_V1=y
+CONFIG_IP_PIMSM_V2=y
+CONFIG_ARPD=y
+CONFIG_INET_ESP=y
+# CONFIG_INET_XFRM_MODE_BEET is not set
+# CONFIG_INET_LRO is not set
+CONFIG_IPV6=y
+CONFIG_IP_SCTP=m
 CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
 CONFIG_PROC_DEVICETREE=y
 CONFIG_BLK_DEV_LOOP=y
@@ -34,6 +58,9 @@ CONFIG_BLK_DEV_RAM=y
 CONFIG_BLK_DEV_RAM_SIZE=131072
 CONFIG_MISC_DEVICES=y
 CONFIG_EEPROM_LEGACY=y
+CONFIG_NETDEVICES=y
+CONFIG_DUMMY=y
+CONFIG_NET_ETHERNET=y
 CONFIG_INPUT_FF_MEMLESS=m
 # CONFIG_INPUT_MOUSEDEV is not set
 # CONFIG_INPUT_KEYBOARD is not set
@@ -64,22 +91,14 @@ CONFIG_NLS=y
 CONFIG_NLS_UTF8=m
 CONFIG_CRC_T10DIF=y
 CONFIG_CRC_ITU_T=m
-CONFIG_LIBCRC32C=m
 CONFIG_FRAME_WARN=1024
 CONFIG_DEBUG_FS=y
 CONFIG_DEBUG_KERNEL=y
 CONFIG_DETECT_HUNG_TASK=y
-# CONFIG_DEBUG_BUGVERBOSE is not set
 CONFIG_DEBUG_INFO=y
 # CONFIG_RCU_CPU_STALL_DETECTOR is not set
 CONFIG_SYSCTL_SYSCALL_CHECK=y
 CONFIG_VIRQ_DEBUG=y
-CONFIG_CRYPTO=y
-CONFIG_CRYPTO_CBC=y
 CONFIG_CRYPTO_PCBC=m
-CONFIG_CRYPTO_HMAC=y
-CONFIG_CRYPTO_MD5=y
-CONFIG_CRYPTO_SHA1=m
-CONFIG_CRYPTO_DES=y
 # CONFIG_CRYPTO_ANSI_CPRNG is not set
 CONFIG_CRYPTO_DEV_TALITOS=y

arch/powerpc/configs/mpc85xx_defconfig

@@ -204,7 +204,6 @@ CONFIG_CRC_T10DIF=y
 CONFIG_DEBUG_FS=y
 CONFIG_DEBUG_KERNEL=y
 CONFIG_DETECT_HUNG_TASK=y
-# CONFIG_DEBUG_BUGVERBOSE is not set
 CONFIG_DEBUG_INFO=y
 # CONFIG_RCU_CPU_STALL_DETECTOR is not set
 CONFIG_SYSCTL_SYSCALL_CHECK=y

arch/powerpc/configs/mpc85xx_smp_defconfig

@@ -206,7 +206,6 @@ CONFIG_CRC_T10DIF=y
 CONFIG_DEBUG_FS=y
 CONFIG_DEBUG_KERNEL=y
 CONFIG_DETECT_HUNG_TASK=y
-# CONFIG_DEBUG_BUGVERBOSE is not set
 CONFIG_DEBUG_INFO=y
 # CONFIG_RCU_CPU_STALL_DETECTOR is not set
 CONFIG_SYSCTL_SYSCALL_CHECK=y

arch/powerpc/configs/mpc86xx_defconfig

@@ -171,7 +171,6 @@ CONFIG_MAC_PARTITION=y
 CONFIG_CRC_T10DIF=y
 CONFIG_DEBUG_KERNEL=y
 CONFIG_DETECT_HUNG_TASK=y
-# CONFIG_DEBUG_BUGVERBOSE is not set
 CONFIG_DEBUG_INFO=y
 # CONFIG_RCU_CPU_STALL_DETECTOR is not set
 CONFIG_SYSCTL_SYSCALL_CHECK=y

arch/powerpc/include/asm/cputable.h

@@ -157,6 +157,7 @@ extern const char *powerpc_base_platform;
 #define CPU_FTR_476_DD2			ASM_CONST(0x0000000000010000)
 #define CPU_FTR_NEED_COHERENT		ASM_CONST(0x0000000000020000)
 #define CPU_FTR_NO_BTIC			ASM_CONST(0x0000000000040000)
+#define CPU_FTR_DEBUG_LVL_EXC		ASM_CONST(0x0000000000080000)
 #define CPU_FTR_NODSISRALIGN		ASM_CONST(0x0000000000100000)
 #define CPU_FTR_PPC_LE			ASM_CONST(0x0000000000200000)
 #define CPU_FTR_REAL_LE			ASM_CONST(0x0000000000400000)
@@ -385,7 +386,8 @@ extern const char *powerpc_base_platform;
 	    CPU_FTR_DBELL)
 #define CPU_FTRS_E5500	(CPU_FTR_USE_TB | CPU_FTR_NODSISRALIGN | \
 	    CPU_FTR_L2CSR | CPU_FTR_LWSYNC | CPU_FTR_NOEXECUTE | \
-	    CPU_FTR_DBELL | CPU_FTR_POPCNTB | CPU_FTR_POPCNTD)
+	    CPU_FTR_DBELL | CPU_FTR_POPCNTB | CPU_FTR_POPCNTD | \
+	    CPU_FTR_DEBUG_LVL_EXC)
 #define CPU_FTRS_GENERIC_32	(CPU_FTR_COMMON | CPU_FTR_NODSISRALIGN)
 
 /* 64-bit CPUs */

arch/powerpc/include/asm/mpic.h

@@ -263,6 +263,7 @@ struct mpic
 #ifdef CONFIG_SMP
 	struct irq_chip		hc_ipi;
 #endif
+	struct irq_chip		hc_tm;
 	const char		*name;
 	/* Flags */
 	unsigned int		flags;
@@ -281,7 +282,7 @@ struct mpic
 
 	/* vector numbers used for internal sources (ipi/timers) */
 	unsigned int		ipi_vecs[4];
-	unsigned int		timer_vecs[4];
+	unsigned int		timer_vecs[8];
 
 	/* Spurious vector to program into unused sources */
 	unsigned int		spurious_vec;
@@ -371,6 +372,8 @@ struct mpic
  * NOTE: This flag trumps MPIC_WANTS_RESET.
  */
 #define MPIC_NO_RESET			0x00004000
+/* Freescale MPIC (compatible includes "fsl,mpic") */
+#define MPIC_FSL			0x00008000
 
 /* MPIC HW modification ID */
 #define MPIC_REGSET_MASK		0xf0000000

arch/powerpc/include/asm/reg_booke.h

@@ -83,6 +83,10 @@
 #define SPRN_IVOR13	0x19D	/* Interrupt Vector Offset Register 13 */
 #define SPRN_IVOR14	0x19E	/* Interrupt Vector Offset Register 14 */
 #define SPRN_IVOR15	0x19F	/* Interrupt Vector Offset Register 15 */
+#define SPRN_IVOR38	0x1B0	/* Interrupt Vector Offset Register 38 */
+#define SPRN_IVOR39	0x1B1	/* Interrupt Vector Offset Register 39 */
+#define SPRN_IVOR40	0x1B2	/* Interrupt Vector Offset Register 40 */
+#define SPRN_IVOR41	0x1B3	/* Interrupt Vector Offset Register 41 */
 #define SPRN_SPEFSCR	0x200	/* SPE & Embedded FP Status & Control */
 #define SPRN_BBEAR	0x201	/* Branch Buffer Entry Address Register */
 #define SPRN_BBTAR	0x202	/* Branch Buffer Target Address Register */

arch/powerpc/kernel/cpu_setup_fsl_booke.S

@@ -88,6 +88,9 @@ _GLOBAL(__setup_cpu_e5500)
 	bl	__e500_dcache_setup
 #ifdef CONFIG_PPC_BOOK3E_64
 	bl	.__setup_base_ivors
+	bl	.setup_perfmon_ivor
+	bl	.setup_doorbell_ivors
+	bl	.setup_ehv_ivors
 #else
 	bl	__setup_e500mc_ivors
 #endif

arch/powerpc/kernel/exceptions-64e.S

@@ -253,9 +253,6 @@ exception_marker:
 	.balign	0x1000
 	.globl interrupt_base_book3e
 interrupt_base_book3e:					/* fake trap */
-	/* Note: If real debug exceptions are supported by the HW, the vector
-	 * below will have to be patched up to point to an appropriate handler
-	 */
 	EXCEPTION_STUB(0x000, machine_check)		/* 0x0200 */
 	EXCEPTION_STUB(0x020, critical_input)		/* 0x0580 */
 	EXCEPTION_STUB(0x040, debug_crit)		/* 0x0d00 */
@@ -272,8 +269,13 @@ interrupt_base_book3e:					/* fake trap */
 	EXCEPTION_STUB(0x1a0, watchdog)			/* 0x09f0 */
 	EXCEPTION_STUB(0x1c0, data_tlb_miss)
 	EXCEPTION_STUB(0x1e0, instruction_tlb_miss)
+	EXCEPTION_STUB(0x260, perfmon)
 	EXCEPTION_STUB(0x280, doorbell)
 	EXCEPTION_STUB(0x2a0, doorbell_crit)
+	EXCEPTION_STUB(0x2c0, guest_doorbell)
+	EXCEPTION_STUB(0x2e0, guest_doorbell_crit)
+	EXCEPTION_STUB(0x300, hypercall)
+	EXCEPTION_STUB(0x320, ehpriv)
 
 	.globl interrupt_end_book3e
 interrupt_end_book3e:
@@ -455,6 +457,70 @@ interrupt_end_book3e:
 kernel_dbg_exc:
 	b	.	/* NYI */
 
+/* Debug exception as a debug interrupt*/
+	START_EXCEPTION(debug_debug);
+	DBG_EXCEPTION_PROLOG(0xd00, PROLOG_ADDITION_2REGS)
+
+	/*
+	 * If there is a single step or branch-taken exception in an
+	 * exception entry sequence, it was probably meant to apply to
+	 * the code where the exception occurred (since exception entry
+	 * doesn't turn off DE automatically).  We simulate the effect
+	 * of turning off DE on entry to an exception handler by turning
+	 * off DE in the DSRR1 value and clearing the debug status.
+	 */
+
+	mfspr	r14,SPRN_DBSR		/* check single-step/branch taken */
+	andis.	r15,r14,DBSR_IC@h
+	beq+	1f
+
+	LOAD_REG_IMMEDIATE(r14,interrupt_base_book3e)
+	LOAD_REG_IMMEDIATE(r15,interrupt_end_book3e)
+	cmpld	cr0,r10,r14
+	cmpld	cr1,r10,r15
+	blt+	cr0,1f
+	bge+	cr1,1f
+
+	/* here it looks like we got an inappropriate debug exception. */
+	lis	r14,DBSR_IC@h		/* clear the IC event */
+	rlwinm	r11,r11,0,~MSR_DE	/* clear DE in the DSRR1 value */
+	mtspr	SPRN_DBSR,r14
+	mtspr	SPRN_DSRR1,r11
+	lwz	r10,PACA_EXDBG+EX_CR(r13)	/* restore registers */
+	ld	r1,PACA_EXDBG+EX_R1(r13)
+	ld	r14,PACA_EXDBG+EX_R14(r13)
+	ld	r15,PACA_EXDBG+EX_R15(r13)
+	mtcr	r10
+	ld	r10,PACA_EXDBG+EX_R10(r13)	/* restore registers */
+	ld	r11,PACA_EXDBG+EX_R11(r13)
+	mfspr	r13,SPRN_SPRG_DBG_SCRATCH
+	rfdi
+
+	/* Normal debug exception */
+	/* XXX We only handle coming from userspace for now since we can't
+	 *     quite save properly an interrupted kernel state yet
+	 */
+1:	andi.	r14,r11,MSR_PR;		/* check for userspace again */
+	beq	kernel_dbg_exc;		/* if from kernel mode */
+
+	/* Now we mash up things to make it look like we are coming on a
+	 * normal exception
+	 */
+	mfspr	r15,SPRN_SPRG_DBG_SCRATCH
+	mtspr	SPRN_SPRG_GEN_SCRATCH,r15
+	mfspr	r14,SPRN_DBSR
+	EXCEPTION_COMMON(0xd00, PACA_EXDBG, INTS_DISABLE_ALL)
+	std	r14,_DSISR(r1)
+	addi	r3,r1,STACK_FRAME_OVERHEAD
+	mr	r4,r14
+	ld	r14,PACA_EXDBG+EX_R14(r13)
+	ld	r15,PACA_EXDBG+EX_R15(r13)
+	bl	.save_nvgprs
+	bl	.DebugException
+	b	.ret_from_except
+
+	MASKABLE_EXCEPTION(0x260, perfmon, .performance_monitor_exception, ACK_NONE)
+
 /* Doorbell interrupt */
 	MASKABLE_EXCEPTION(0x2070, doorbell, .doorbell_exception, ACK_NONE)
 
@@ -469,6 +535,11 @@ kernel_dbg_exc:
 //	b	ret_from_crit_except
 	b	.
 
+	MASKABLE_EXCEPTION(0x2c0, guest_doorbell, .unknown_exception, ACK_NONE)
+	MASKABLE_EXCEPTION(0x2e0, guest_doorbell_crit, .unknown_exception, ACK_NONE)
+	MASKABLE_EXCEPTION(0x310, hypercall, .unknown_exception, ACK_NONE)
+	MASKABLE_EXCEPTION(0x320, ehpriv, .unknown_exception, ACK_NONE)
+
 
 /*
  * An interrupt came in while soft-disabled; clear EE in SRR1,
@@ -588,7 +659,12 @@ fast_exception_return:
 BAD_STACK_TRAMPOLINE(0x000)
 BAD_STACK_TRAMPOLINE(0x100)
 BAD_STACK_TRAMPOLINE(0x200)
+BAD_STACK_TRAMPOLINE(0x260)
+BAD_STACK_TRAMPOLINE(0x2c0)
+BAD_STACK_TRAMPOLINE(0x2e0)
 BAD_STACK_TRAMPOLINE(0x300)
+BAD_STACK_TRAMPOLINE(0x310)
+BAD_STACK_TRAMPOLINE(0x320)
 BAD_STACK_TRAMPOLINE(0x400)
 BAD_STACK_TRAMPOLINE(0x500)
 BAD_STACK_TRAMPOLINE(0x600)
@@ -1124,3 +1200,33 @@ _GLOBAL(__setup_base_ivors)
 	sync
 
 	blr
+
+_GLOBAL(setup_perfmon_ivor)
+	SET_IVOR(35, 0x260) /* Performance Monitor */
+	blr
+
+_GLOBAL(setup_doorbell_ivors)
+	SET_IVOR(36, 0x280) /* Processor Doorbell */
+	SET_IVOR(37, 0x2a0) /* Processor Doorbell Crit */
+
+	/* Check MMUCFG[LPIDSIZE] to determine if we have category E.HV */
+	mfspr	r10,SPRN_MMUCFG
+	rlwinm.	r10,r10,0,MMUCFG_LPIDSIZE
+	beqlr
+
+	SET_IVOR(38, 0x2c0) /* Guest Processor Doorbell */
+	SET_IVOR(39, 0x2e0) /* Guest Processor Doorbell Crit/MC */
+	blr
+
+_GLOBAL(setup_ehv_ivors)
+	/*
+	 * We may be running as a guest and lack E.HV even on a chip
+	 * that normally has it.
+	 */
+	mfspr	r10,SPRN_MMUCFG
+	rlwinm.	r10,r10,0,MMUCFG_LPIDSIZE
+	beqlr
+
+	SET_IVOR(40, 0x300) /* Embedded Hypervisor System Call */
+	SET_IVOR(41, 0x320) /* Embedded Hypervisor Privilege */
+	blr

arch/powerpc/kernel/setup_64.c

@@ -62,6 +62,7 @@
 #include <asm/udbg.h>
 #include <asm/kexec.h>
 #include <asm/mmu_context.h>
+#include <asm/code-patching.h>
 
 #include "setup.h"
 
@@ -477,6 +478,9 @@ static void __init irqstack_early_init(void)
 #ifdef CONFIG_PPC_BOOK3E
 static void __init exc_lvl_early_init(void)
 {
+	extern unsigned int interrupt_base_book3e;
+	extern unsigned int exc_debug_debug_book3e;
+
 	unsigned int i;
 
 	for_each_possible_cpu(i) {
@@ -487,6 +491,10 @@ static void __init exc_lvl_early_init(void)
 		mcheckirq_ctx[i] = (struct thread_info *)
 			__va(memblock_alloc(THREAD_SIZE, THREAD_SIZE));
 	}
+
+	if (cpu_has_feature(CPU_FTR_DEBUG_LVL_EXC))
+		patch_branch(&interrupt_base_book3e + (0x040 / 4) + 1,
+			     (unsigned long)&exc_debug_debug_book3e, 0);
 }
 #else
 #define exc_lvl_early_init()

arch/powerpc/platforms/86xx/mpc8610_hpcd.c

@@ -66,7 +66,7 @@ static void __init mpc8610_suspend_init(void)
 		return;
 	}
 
-	ret = request_irq(irq, mpc8610_sw9_irq, 0, "sw9/wakeup", NULL);
+	ret = request_irq(irq, mpc8610_sw9_irq, 0, "sw9:wakeup", NULL);
 	if (ret) {
 		pr_err("%s: can't request pixis event IRQ: %d\n",
 		       __func__, ret);
@@ -105,45 +105,77 @@ machine_device_initcall(mpc86xx_hpcd, mpc8610_declare_of_platform_devices);
 
 #if defined(CONFIG_FB_FSL_DIU) || defined(CONFIG_FB_FSL_DIU_MODULE)
 
-static u32 get_busfreq(void)
-{
-	struct device_node *node;
-
-	u32 fs_busfreq = 0;
-	node = of_find_node_by_type(NULL, "cpu");
-	if (node) {
-		unsigned int size;
-		const unsigned int *prop =
-			of_get_property(node, "bus-frequency", &size);
-		if (prop)
-			fs_busfreq = *prop;
-		of_node_put(node);
-	};
-	return fs_busfreq;
-}
+/*
+ * DIU Area Descriptor
+ *
+ * The MPC8610 reference manual shows the bits of the AD register in
+ * little-endian order, which causes the BLUE_C field to be split into two
+ * parts. To simplify the definition of the MAKE_AD() macro, we define the
+ * fields in big-endian order and byte-swap the result.
+ *
+ * So even though the registers don't look like they're in the
+ * same bit positions as they are on the P1022, the same value is written to
+ * the AD register on the MPC8610 and on the P1022.
+ */
+#define AD_BYTE_F		0x10000000
+#define AD_ALPHA_C_MASK		0x0E000000
+#define AD_ALPHA_C_SHIFT	25
+#define AD_BLUE_C_MASK		0x01800000
+#define AD_BLUE_C_SHIFT		23
+#define AD_GREEN_C_MASK		0x00600000
+#define AD_GREEN_C_SHIFT	21
+#define AD_RED_C_MASK		0x00180000
+#define AD_RED_C_SHIFT		19
+#define AD_PALETTE		0x00040000
+#define AD_PIXEL_S_MASK		0x00030000
+#define AD_PIXEL_S_SHIFT	16
+#define AD_COMP_3_MASK		0x0000F000
+#define AD_COMP_3_SHIFT		12
+#define AD_COMP_2_MASK		0x00000F00
+#define AD_COMP_2_SHIFT		8
+#define AD_COMP_1_MASK		0x000000F0
+#define AD_COMP_1_SHIFT		4
+#define AD_COMP_0_MASK		0x0000000F
+#define AD_COMP_0_SHIFT		0
+
+#define MAKE_AD(alpha, red, blue, green, size, c0, c1, c2, c3) \
+	cpu_to_le32(AD_BYTE_F | (alpha << AD_ALPHA_C_SHIFT) | \
+	(blue << AD_BLUE_C_SHIFT) | (green << AD_GREEN_C_SHIFT) | \
+	(red << AD_RED_C_SHIFT) | (c3 << AD_COMP_3_SHIFT) | \
+	(c2 << AD_COMP_2_SHIFT) | (c1 << AD_COMP_1_SHIFT) | \
+	(c0 << AD_COMP_0_SHIFT) | (size << AD_PIXEL_S_SHIFT))
 
 unsigned int mpc8610hpcd_get_pixel_format(unsigned int bits_per_pixel,
 						int monitor_port)
 {
 	static const unsigned long pixelformat[][3] = {
-		{0x88882317, 0x88083218, 0x65052119},
-		{0x88883316, 0x88082219, 0x65053118},
+		{
+			MAKE_AD(3, 0, 2, 1, 3, 8, 8, 8, 8),
+			MAKE_AD(4, 2, 0, 1, 2, 8, 8, 8, 0),
+			MAKE_AD(4, 0, 2, 1, 1, 5, 6, 5, 0)
+		},
+		{
+			MAKE_AD(3, 2, 0, 1, 3, 8, 8, 8, 8),
+			MAKE_AD(4, 0, 2, 1, 2, 8, 8, 8, 0),
+			MAKE_AD(4, 2, 0, 1, 1, 5, 6, 5, 0)
+		},
 	};
-	unsigned int pix_fmt, arch_monitor;
+	unsigned int arch_monitor;
 
+	/* The DVI port is mis-wired on revision 1 of this board. */
 	arch_monitor = ((*pixis_arch == 0x01) && (monitor_port == 0))? 0 : 1;
-		/* DVI port for board version 0x01 */
-
-	if (bits_per_pixel == 32)
-		pix_fmt = pixelformat[arch_monitor][0];
-	else if (bits_per_pixel == 24)
-		pix_fmt = pixelformat[arch_monitor][1];
-	else if (bits_per_pixel == 16)
-		pix_fmt = pixelformat[arch_monitor][2];
-	else
-		pix_fmt = pixelformat[1][0];
-
-	return pix_fmt;
+
+	switch (bits_per_pixel) {
+	case 32:
+		return pixelformat[arch_monitor][0];
+	case 24:
+		return pixelformat[arch_monitor][1];
+	case 16:
+		return pixelformat[arch_monitor][2];
+	default:
+		pr_err("fsl-diu: unsupported pixel depth %u\n", bits_per_pixel);
+		return 0;
+	}
 }
 
 void mpc8610hpcd_set_gamma_table(int monitor_port, char *gamma_table_base)
@@ -190,8 +222,7 @@ void mpc8610hpcd_set_pixel_clock(unsigned int pixclock)
 	}
 
 	/* Pixel Clock configuration */
-	pr_debug("DIU: Bus Frequency = %d\n", get_busfreq());
-	speed_ccb = get_busfreq();
+	speed_ccb = fsl_get_sys_freq();
 
 	/* Calculate the pixel clock with the smallest error */
 	/* calculate the following in steps to avoid overflow */

arch/powerpc/sysdev/mpic.c

@@ -6,6 +6,7 @@
  *  with various broken implementations of this HW.
  *
  *  Copyright (C) 2004 Benjamin Herrenschmidt, IBM Corp.
+ *  Copyright 2010-2011 Freescale Semiconductor, Inc.
  *
  *  This file is subject to the terms and conditions of the GNU General Public
  *  License.  See the file COPYING in the main directory of this archive
@@ -218,6 +219,28 @@ static inline void _mpic_ipi_write(struct mpic *mpic, unsigned int ipi, u32 valu
 	_mpic_write(mpic->reg_type, &mpic->gregs, offset, value);
 }
 
+static inline u32 _mpic_tm_read(struct mpic *mpic, unsigned int tm)
+{
+	unsigned int offset = MPIC_INFO(TIMER_VECTOR_PRI) +
+			      ((tm & 3) * MPIC_INFO(TIMER_STRIDE));
+
+	if (tm >= 4)
+		offset += 0x1000 / 4;
+
+	return _mpic_read(mpic->reg_type, &mpic->tmregs, offset);
+}
+
+static inline void _mpic_tm_write(struct mpic *mpic, unsigned int tm, u32 value)
+{
+	unsigned int offset = MPIC_INFO(TIMER_VECTOR_PRI) +
+			      ((tm & 3) * MPIC_INFO(TIMER_STRIDE));
+
+	if (tm >= 4)
+		offset += 0x1000 / 4;
+
+	_mpic_write(mpic->reg_type, &mpic->tmregs, offset, value);
+}
+
 static inline u32 _mpic_cpu_read(struct mpic *mpic, unsigned int reg)
 {
 	unsigned int cpu = mpic_processor_id(mpic);
@@ -268,6 +291,8 @@ static inline void _mpic_irq_write(struct mpic *mpic, unsigned int src_no,
 #define mpic_write(b,r,v)	_mpic_write(mpic->reg_type,&(b),(r),(v))
 #define mpic_ipi_read(i)	_mpic_ipi_read(mpic,(i))
 #define mpic_ipi_write(i,v)	_mpic_ipi_write(mpic,(i),(v))
+#define mpic_tm_read(i)		_mpic_tm_read(mpic,(i))
+#define mpic_tm_write(i,v)	_mpic_tm_write(mpic,(i),(v))
 #define mpic_cpu_read(i)	_mpic_cpu_read(mpic,(i))
 #define mpic_cpu_write(i,v)	_mpic_cpu_write(mpic,(i),(v))
 #define mpic_irq_read(s,r)	_mpic_irq_read(mpic,(s),(r))
@@ -624,6 +649,13 @@ static unsigned int mpic_is_ipi(struct mpic *mpic, unsigned int irq)
 	return (src >= mpic->ipi_vecs[0] && src <= mpic->ipi_vecs[3]);
 }
 
+/* Determine if the linux irq is a timer */
+static unsigned int mpic_is_tm(struct mpic *mpic, unsigned int irq)
+{
+	unsigned int src = virq_to_hw(irq);
+
+	return (src >= mpic->timer_vecs[0] && src <= mpic->timer_vecs[7]);
+}
 
 /* Convert a cpu mask from logical to physical cpu numbers. */
 static inline u32 mpic_physmask(u32 cpumask)
@@ -810,6 +842,25 @@ static void mpic_end_ipi(struct irq_data *d)
 
 #endif /* CONFIG_SMP */
 
+static void mpic_unmask_tm(struct irq_data *d)
+{
+	struct mpic *mpic = mpic_from_irq_data(d);
+	unsigned int src = virq_to_hw(d->irq) - mpic->timer_vecs[0];
+
+	DBG("%s: enable_tm: %d (tm %d)\n", mpic->name, irq, src);
+	mpic_tm_write(src, mpic_tm_read(src) & ~MPIC_VECPRI_MASK);
+	mpic_tm_read(src);
+}
+
+static void mpic_mask_tm(struct irq_data *d)
+{
+	struct mpic *mpic = mpic_from_irq_data(d);
+	unsigned int src = virq_to_hw(d->irq) - mpic->timer_vecs[0];
+
+	mpic_tm_write(src, mpic_tm_read(src) | MPIC_VECPRI_MASK);
+	mpic_tm_read(src);
+}
+
 int mpic_set_affinity(struct irq_data *d, const struct cpumask *cpumask,
 		      bool force)
 {
@@ -936,6 +987,12 @@ static struct irq_chip mpic_ipi_chip = {
 };
 #endif /* CONFIG_SMP */
 
+static struct irq_chip mpic_tm_chip = {
+	.irq_mask	= mpic_mask_tm,
+	.irq_unmask	= mpic_unmask_tm,
+	.irq_eoi	= mpic_end_irq,
+};
+
 #ifdef CONFIG_MPIC_U3_HT_IRQS
 static struct irq_chip mpic_irq_ht_chip = {
 	.irq_startup	= mpic_startup_ht_irq,
@@ -979,6 +1036,16 @@ static int mpic_host_map(struct irq_host *h, unsigned int virq,
 	}
 #endif /* CONFIG_SMP */
 
+	if (hw >= mpic->timer_vecs[0] && hw <= mpic->timer_vecs[7]) {
+		WARN_ON(!(mpic->flags & MPIC_PRIMARY));
+
+		DBG("mpic: mapping as timer\n");
+		irq_set_chip_data(virq, mpic);
+		irq_set_chip_and_handler(virq, &mpic->hc_tm,
+					 handle_fasteoi_irq);
+		return 0;
+	}
+
 	if (hw >= mpic->irq_count)
 		return -EINVAL;
 
@@ -1019,6 +1086,7 @@ static int mpic_host_xlate(struct irq_host *h, struct device_node *ct,
 			   irq_hw_number_t *out_hwirq, unsigned int *out_flags)
 
 {
+	struct mpic *mpic = h->host_data;
 	static unsigned char map_mpic_senses[4] = {
 		IRQ_TYPE_EDGE_RISING,
 		IRQ_TYPE_LEVEL_LOW,
@@ -1027,7 +1095,38 @@ static int mpic_host_xlate(struct irq_host *h, struct device_node *ct,
 	};
 
 	*out_hwirq = intspec[0];
-	if (intsize > 1) {
+	if (intsize >= 4 && (mpic->flags & MPIC_FSL)) {
+		/*
+		 * Freescale MPIC with extended intspec:
+		 * First two cells are as usual.  Third specifies
+		 * an "interrupt type".  Fourth is type-specific data.
+		 *
+		 * See Documentation/devicetree/bindings/powerpc/fsl/mpic.txt
+		 */
+		switch (intspec[2]) {
+		case 0:
+		case 1: /* no EISR/EIMR support for now, treat as shared IRQ */
+			break;
+		case 2:
+			if (intspec[0] >= ARRAY_SIZE(mpic->ipi_vecs))
+				return -EINVAL;
+
+			*out_hwirq = mpic->ipi_vecs[intspec[0]];
+			break;
+		case 3:
+			if (intspec[0] >= ARRAY_SIZE(mpic->timer_vecs))
+				return -EINVAL;
+
+			*out_hwirq = mpic->timer_vecs[intspec[0]];
+			break;
+		default:
+			pr_debug("%s: unknown irq type %u\n",
+				 __func__, intspec[2]);
+			return -EINVAL;
+		}
+
+		*out_flags = map_mpic_senses[intspec[1] & 3];
+	} else if (intsize > 1) {
 		u32 mask = 0x3;
 
 		/* Apple invented a new race of encoding on machines with
@@ -1103,6 +1202,9 @@ struct mpic * __init mpic_alloc(struct device_node *node,
 	mpic->hc_ipi.name = name;
 #endif /* CONFIG_SMP */
 
+	mpic->hc_tm = mpic_tm_chip;
+	mpic->hc_tm.name = name;
+
 	mpic->flags = flags;
 	mpic->isu_size = isu_size;
 	mpic->irq_count = irq_count;
@@ -1113,10 +1215,14 @@ struct mpic * __init mpic_alloc(struct device_node *node,
 	else
 		intvec_top = 255;
 
-	mpic->timer_vecs[0] = intvec_top - 8;
-	mpic->timer_vecs[1] = intvec_top - 7;
-	mpic->timer_vecs[2] = intvec_top - 6;
-	mpic->timer_vecs[3] = intvec_top - 5;
+	mpic->timer_vecs[0] = intvec_top - 12;
+	mpic->timer_vecs[1] = intvec_top - 11;
+	mpic->timer_vecs[2] = intvec_top - 10;
+	mpic->timer_vecs[3] = intvec_top - 9;
+	mpic->timer_vecs[4] = intvec_top - 8;
+	mpic->timer_vecs[5] = intvec_top - 7;
+	mpic->timer_vecs[6] = intvec_top - 6;
+	mpic->timer_vecs[7] = intvec_top - 5;
 	mpic->ipi_vecs[0]   = intvec_top - 4;
 	mpic->ipi_vecs[1]   = intvec_top - 3;
 	mpic->ipi_vecs[2]   = intvec_top - 2;
@@ -1126,6 +1232,8 @@ struct mpic * __init mpic_alloc(struct device_node *node,
 	/* Check for "big-endian" in device-tree */
 	if (node && of_get_property(node, "big-endian", NULL) != NULL)
 		mpic->flags |= MPIC_BIG_ENDIAN;
+	if (node && of_device_is_compatible(node, "fsl,mpic"))
+		mpic->flags |= MPIC_FSL;
 
 	/* Look for protected sources */
 	if (node) {
@@ -1317,15 +1425,17 @@ void __init mpic_init(struct mpic *mpic)
 	/* Set current processor priority to max */
 	mpic_cpu_write(MPIC_INFO(CPU_CURRENT_TASK_PRI), 0xf);
 
-	/* Initialize timers: just disable them all */
+	/* Initialize timers to our reserved vectors and mask them for now */
 	for (i = 0; i < 4; i++) {
 		mpic_write(mpic->tmregs,
 			   i * MPIC_INFO(TIMER_STRIDE) +
-			   MPIC_INFO(TIMER_DESTINATION), 0);
+			   MPIC_INFO(TIMER_DESTINATION),
+			   1 << hard_smp_processor_id());
 		mpic_write(mpic->tmregs,
 			   i * MPIC_INFO(TIMER_STRIDE) +
 			   MPIC_INFO(TIMER_VECTOR_PRI),
 			   MPIC_VECPRI_MASK |
+			   (9 << MPIC_VECPRI_PRIORITY_SHIFT) |
 			   (mpic->timer_vecs[0] + i));
 	}
 
@@ -1434,6 +1544,11 @@ void mpic_irq_set_priority(unsigned int irq, unsigned int pri)
 			~MPIC_VECPRI_PRIORITY_MASK;
 		mpic_ipi_write(src - mpic->ipi_vecs[0],
 			       reg | (pri << MPIC_VECPRI_PRIORITY_SHIFT));
+	} else if (mpic_is_tm(mpic, irq)) {
+		reg = mpic_tm_read(src - mpic->timer_vecs[0]) &
+			~MPIC_VECPRI_PRIORITY_MASK;
+		mpic_tm_write(src - mpic->timer_vecs[0],
+			      reg | (pri << MPIC_VECPRI_PRIORITY_SHIFT));
 	} else {
 		reg = mpic_irq_read(src, MPIC_INFO(IRQ_VECTOR_PRI))
 			& ~MPIC_VECPRI_PRIORITY_MASK;