Merge tag 'mvebu_fixes_for_v3.8' of git://git.infradead.org/users/jcooper/linux into fixes

From Jason Cooper:

fixes for mvebu/kirkwood v3.8
 - use correct uart driver for mvebu boards
 - add a missing DT clocks
 - gpio-poweroff level vs. edge triggering, use gpio_is_valid()
 - remove an inappropriate __init, modules need to access function.
 - various DT fixes
 - error handling in mv_xor

* tag 'mvebu_fixes_for_v3.8' of git://git.infradead.org/users/jcooper/linux:
  pinctrl: mvebu: make pdma clock on dove mandatory
  ARM: Dove: Add pinctrl clock to DT
  dma: mv_xor: fix error handling for clocks
  dma: mv_xor: fix error handling of mv_xor_channel_add()
  arm: mvebu: Add missing ; for cpu node.
  arm: mvebu: Armada XP MV78230 has only three Ethernet interfaces
  arm: mvebu: Armada XP MV78230 has two cores, not one
  clk: mvebu: Remove inappropriate __init tagging
  ARM: Kirkwood: Use fixed-regulator instead of board gpio call
  ARM: Kirkwood: Fix missing sdio clock
  ARM: Kirkwood: Switch TWSI1 of 88f6282 to DT clock providers
  Power: gpio-poweroff: Fix documentation and gpio_is_valid
  ARM: Kirkwood: Fix missing clk for USB device.
  arm: mvebu: Use dw-apb-uart instead of ns16650 as UART driver
Signed-off-by: Olof Johansson <olof@lixom.net>

Documentation/devicetree/bindings/gpio/gpio-poweroff.txt

-GPIO line that should be set high/low to power off a device
+Driver a GPIO line that can be used to turn the power off.
+
+The driver supports both level triggered and edge triggered power off.
+At driver load time, the driver will request the given gpio line and
+install a pm_power_off handler. If the optional properties 'input' is
+not found, the GPIO line will be driven in the inactive
+state. Otherwise its configured as an input.
+
+When the pm_power_off is called, the gpio is configured as an output,
+and drive active, so triggering a level triggered power off
+condition. This will also cause an inactive->active edge condition, so
+triggering positive edge triggered power off. After a delay of 100ms,
+the GPIO is set to inactive, thus causing an active->inactive edge,
+triggering negative edge triggered power off. After another 100ms
+delay the GPIO is driver active again. If the power is still on and
+the CPU still running after a 3000ms delay, a WARN_ON(1) is emitted.
 
 Required properties:
 - compatible : should be "gpio-poweroff".
@@ -13,10 +28,9 @@ Optional properties:
   property is not specified, the GPIO is initialized as an output in its
   inactive state.
 
-
 Examples:
 
 gpio-poweroff {
 	compatible = "gpio-poweroff";
-	gpios = <&gpio 4 0>; /* GPIO 4 Active Low */
+	gpios = <&gpio 4 0>;
 };

arch/arm/boot/dts/armada-370-xp.dtsi

@@ -50,17 +50,19 @@ soc {
 		ranges;
 
 		serial@d0012000 {
-				compatible = "ns16550";
+				compatible = "snps,dw-apb-uart";
 				reg = <0xd0012000 0x100>;
 				reg-shift = <2>;
 				interrupts = <41>;
+				reg-io-width = <4>;
 				status = "disabled";
 		};
 		serial@d0012100 {
-				compatible = "ns16550";
+				compatible = "snps,dw-apb-uart";
 				reg = <0xd0012100 0x100>;
 				reg-shift = <2>;
 				interrupts = <42>;
+				reg-io-width = <4>;
 				status = "disabled";
 		};
 

arch/arm/boot/dts/armada-xp-mv78230.dtsi

@@ -34,7 +34,14 @@ cpu@0 {
 		reg = <0>;
 		clocks = <&cpuclk 0>;
 	    };
-	}
+
+	    cpu@1 {
+		device_type = "cpu";
+		compatible = "marvell,sheeva-v7";
+		reg = <1>;
+		clocks = <&cpuclk 1>;
+	    };
+	};
 
 	soc {
 		pinctrl {

arch/arm/boot/dts/armada-xp-mv78260.dtsi

@@ -85,5 +85,13 @@ gpio2: gpio@d0018180 {
 			#interrupts-cells = <2>;
 			interrupts = <24>;
 		};
+
+		ethernet@d0034000 {
+				compatible = "marvell,armada-370-neta";
+				reg = <0xd0034000 0x2500>;
+				interrupts = <14>;
+				clocks = <&gateclk 1>;
+				status = "disabled";
+		};
 	};
 };

arch/arm/boot/dts/armada-xp-mv78460.dtsi

@@ -100,5 +100,13 @@ gpio2: gpio@d0018180 {
 			#interrupts-cells = <2>;
 			interrupts = <24>;
 		};
+
+		ethernet@d0034000 {
+				compatible = "marvell,armada-370-neta";
+				reg = <0xd0034000 0x2500>;
+				interrupts = <14>;
+				clocks = <&gateclk 1>;
+				status = "disabled";
+		};
 	};
  };

arch/arm/boot/dts/armada-xp.dtsi

@@ -42,17 +42,19 @@ armada-370-xp-pmsu@d0022000 {
 
 	soc {
 		serial@d0012200 {
-				compatible = "ns16550";
+				compatible = "snps,dw-apb-uart";
 				reg = <0xd0012200 0x100>;
 				reg-shift = <2>;
 				interrupts = <43>;
+				reg-io-width = <4>;
 				status = "disabled";
 		};
 		serial@d0012300 {
-				compatible = "ns16550";
+				compatible = "snps,dw-apb-uart";
 				reg = <0xd0012300 0x100>;
 				reg-shift = <2>;
 				interrupts = <44>;
+				reg-io-width = <4>;
 				status = "disabled";
 		};
 
@@ -93,14 +95,6 @@ ethernet@d0030000 {
 				status = "disabled";
 		};
 
-		ethernet@d0034000 {
-				compatible = "marvell,armada-370-neta";
-				reg = <0xd0034000 0x2500>;
-				interrupts = <14>;
-				clocks = <&gateclk 1>;
-				status = "disabled";
-		};
-
 		xor@d0060900 {
 			compatible = "marvell,orion-xor";
 			reg = <0xd0060900 0x100

arch/arm/boot/dts/dove.dtsi

@@ -117,6 +117,7 @@ gpio2: gpio@e8400 {
 		pinctrl: pinctrl@d0200 {
 			compatible = "marvell,dove-pinctrl";
 			reg = <0xd0200 0x10>;
+			clocks = <&gate_clk 22>;
 		};
 
 		spi0: spi@10600 {

arch/arm/boot/dts/kirkwood-6282.dtsi

@@ -39,6 +39,7 @@ i2c@11100 {
 			#size-cells = <0>;
 			interrupts = <32>;
 			clock-frequency = <100000>;
+			clocks = <&gate_clk 7>;
 			status = "disabled";
 		};
 	};

arch/arm/boot/dts/kirkwood-topkick.dts

@@ -82,4 +82,21 @@ wifi2 {
 			gpios = <&gpio1 16 1>;
 		};
 	};
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		sata0_power: regulator@1 {
+			compatible = "regulator-fixed";
+			reg = <1>;
+			regulator-name = "SATA0 Power";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			enable-active-high;
+			regulator-always-on;
+			regulator-boot-on;
+			gpio = <&gpio1 4 0>;
+		};
+	};
 };

arch/arm/boot/dts/kirkwood.dtsi

@@ -144,6 +144,7 @@ ehci@50000 {
 			compatible = "marvell,orion-ehci";
 			reg = <0x50000 0x1000>;
 			interrupts = <19>;
+			clocks = <&gate_clk 3>;
 			status = "okay";
 		};
 

arch/arm/configs/mvebu_defconfig

@@ -33,9 +33,7 @@ CONFIG_MVNETA=y
 CONFIG_MARVELL_PHY=y
 CONFIG_SERIAL_8250=y
 CONFIG_SERIAL_8250_CONSOLE=y
-CONFIG_SERIAL_OF_PLATFORM=y
-CONFIG_I2C=y
-CONFIG_I2C_MV64XXX=y
+CONFIG_SERIAL_8250_DW=y
 CONFIG_GPIOLIB=y
 CONFIG_GPIO_SYSFS=y
 # CONFIG_USB_SUPPORT is not set

arch/arm/mach-kirkwood/board-dt.c

@@ -67,6 +67,10 @@ static void __init kirkwood_legacy_clk_init(void)
 	orion_clkdev_add(NULL, "mv643xx_eth_port.1",
 			 of_clk_get_from_provider(&clkspec));
 
+	clkspec.args[0] = CGC_BIT_SDIO;
+	orion_clkdev_add(NULL, "mvsdio",
+			 of_clk_get_from_provider(&clkspec));
+
 }
 
 static void __init kirkwood_of_clk_init(void)

arch/arm/mach-kirkwood/board-usi_topkick.c

@@ -64,8 +64,6 @@ static unsigned int topkick_mpp_config[] __initdata = {
 	0
 };
 
-#define TOPKICK_SATA0_PWR_ENABLE 36
-
 void __init usi_topkick_init(void)
 {
 	/*
@@ -73,8 +71,6 @@ void __init usi_topkick_init(void)
 	 */
 	kirkwood_mpp_conf(topkick_mpp_config);
 
-	/* SATA0 power enable */
-	gpio_set_value(TOPKICK_SATA0_PWR_ENABLE, 1);
 
 	kirkwood_ge00_init(&topkick_ge00_data);
 	kirkwood_sdio_init(&topkick_mvsdio_data);

drivers/clk/mvebu/clk-gating-ctrl.c

@@ -32,7 +32,7 @@ struct mvebu_soc_descr {
 
 #define to_clk_gate(_hw) container_of(_hw, struct clk_gate, hw)
 
-static struct clk __init *mvebu_clk_gating_get_src(
+static struct clk *mvebu_clk_gating_get_src(
 	struct of_phandle_args *clkspec, void *data)
 {
 	struct mvebu_gating_ctrl *ctrl = (struct mvebu_gating_ctrl *)data;

drivers/dma/mv_xor.c

@@ -1361,13 +1361,16 @@ static int mv_xor_probe(struct platform_device *pdev)
 err_channel_add:
 	for (i = 0; i < MV_XOR_MAX_CHANNELS; i++)
 		if (xordev->channels[i]) {
+			mv_xor_channel_remove(xordev->channels[i]);
 			if (pdev->dev.of_node)
 				irq_dispose_mapping(xordev->channels[i]->irq);
-			mv_xor_channel_remove(xordev->channels[i]);
 		}
 
+	if (!IS_ERR(xordev->clk)) {
 		clk_disable_unprepare(xordev->clk);
 		clk_put(xordev->clk);
+	}
+
 	return ret;
 }
 

drivers/pinctrl/mvebu/pinctrl-dove.c

@@ -595,7 +595,10 @@ static int __devinit dove_pinctrl_probe(struct platform_device *pdev)
 	 * grab clk to make sure it is ticking.
 	 */
 	clk = devm_clk_get(&pdev->dev, NULL);
-	if (!IS_ERR(clk))
+	if (IS_ERR(clk)) {
+		dev_err(&pdev->dev, "Unable to get pdma clock");
+		return PTR_RET(clk);
+	}
 	clk_prepare_enable(clk);
 
 	return mvebu_pinctrl_probe(pdev);

drivers/power/reset/gpio-poweroff.c

@@ -29,15 +29,16 @@ static int gpio_active_low;
 
 static void gpio_poweroff_do_poweroff(void)
 {
-	BUG_ON(gpio_num == -1);
+	BUG_ON(!gpio_is_valid(gpio_num));
 
-	/* drive it active */
+	/* drive it active, also inactive->active edge */
 	gpio_direction_output(gpio_num, !gpio_active_low);
 	mdelay(100);
-	/* rising edge or drive inactive */
+	/* drive inactive, also active->inactive edge */
 	gpio_set_value(gpio_num, gpio_active_low);
 	mdelay(100);
-	/* falling edge */
+
+	/* drive it active, also inactive->active edge */
 	gpio_set_value(gpio_num, !gpio_active_low);
 
 	/* give it some time */
@@ -60,15 +61,12 @@ static int __devinit gpio_poweroff_probe(struct platform_device *pdev)
 	}
 
 	gpio_num = of_get_gpio_flags(pdev->dev.of_node, 0, &flags);
-	if (gpio_num < 0) {
-		pr_err("%s: Could not get GPIO configuration: %d",
-		       __func__, gpio_num);
-		return -ENODEV;
-	}
+	if (!gpio_is_valid(gpio_num))
+		return gpio_num;
+
 	gpio_active_low = flags & OF_GPIO_ACTIVE_LOW;
 
-	if (of_get_property(pdev->dev.of_node, "input", NULL))
-		input = true;
+	input = of_property_read_bool(pdev->dev.of_node, "input");
 
 	ret = gpio_request(gpio_num, "poweroff-gpio");
 	if (ret) {
@@ -98,7 +96,6 @@ static int __devinit gpio_poweroff_probe(struct platform_device *pdev)
 
 static int __devexit gpio_poweroff_remove(struct platform_device *pdev)
 {
-	if (gpio_num != -1)
 	gpio_free(gpio_num);
 	if (pm_power_off == &gpio_poweroff_do_poweroff)
 		pm_power_off = NULL;
@@ -125,5 +122,5 @@ module_platform_driver(gpio_poweroff_driver);
 
 MODULE_AUTHOR("Jamie Lentin <jm@lentin.co.uk>");
 MODULE_DESCRIPTION("GPIO poweroff driver");
-MODULE_LICENSE("GPL");
+MODULE_LICENSE("GPL v2");
 MODULE_ALIAS("platform:poweroff-gpio");