fec: add support for PHY interface platform data

The i.MX25 PDK uses RMII to communicate with its PHY. This patch adds
the ability to configure RMII, based on platform data.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/fec.c

@@ -41,6 +41,7 @@
 #include <linux/clk.h>
 #include <linux/platform_device.h>
 #include <linux/phy.h>
+#include <linux/fec.h>
 
 #include <asm/cacheflush.h>
 
@@ -182,6 +183,7 @@ struct fec_enet_private {
 	struct  phy_device *phy_dev;
 	int     mii_timeout;
 	uint    phy_speed;
+	phy_interface_t	phy_interface;
 	int	index;
 	int	link;
 	int	full_duplex;
@@ -1191,6 +1193,21 @@ fec_restart(struct net_device *dev, int duplex)
 	/* Set MII speed */
 	writel(fep->phy_speed, fep->hwp + FEC_MII_SPEED);
 
+#ifdef FEC_MIIGSK_ENR
+	if (fep->phy_interface == PHY_INTERFACE_MODE_RMII) {
+		/* disable the gasket and wait */
+		writel(0, fep->hwp + FEC_MIIGSK_ENR);
+		while (readl(fep->hwp + FEC_MIIGSK_ENR) & 4)
+			udelay(1);
+
+		/* configure the gasket: RMII, 50 MHz, no loopback, no echo */
+		writel(1, fep->hwp + FEC_MIIGSK_CFGR);
+
+		/* re-enable the gasket */
+		writel(2, fep->hwp + FEC_MIIGSK_ENR);
+	}
+#endif
+
 	/* And last, enable the transmit and receive processing */
 	writel(2, fep->hwp + FEC_ECNTRL);
 	writel(0, fep->hwp + FEC_R_DES_ACTIVE);
@@ -1226,6 +1243,7 @@ static int __devinit
 fec_probe(struct platform_device *pdev)
 {
 	struct fec_enet_private *fep;
+	struct fec_platform_data *pdata;
 	struct net_device *ndev;
 	int i, irq, ret = 0;
 	struct resource *r;
@@ -1259,6 +1277,10 @@ fec_probe(struct platform_device *pdev)
 
 	platform_set_drvdata(pdev, ndev);
 
+	pdata = pdev->dev.platform_data;
+	if (pdata)
+		fep->phy_interface = pdata->phy;
+
 	/* This device has up to three irqs on some platforms */
 	for (i = 0; i < 3; i++) {
 		irq = platform_get_irq(pdev, i);

drivers/net/fec.h

@@ -43,6 +43,8 @@
 #define FEC_R_DES_START		0x180 /* Receive descriptor ring */
 #define FEC_X_DES_START		0x184 /* Transmit descriptor ring */
 #define FEC_R_BUFF_SIZE		0x188 /* Maximum receive buff size */
+#define FEC_MIIGSK_CFGR		0x300 /* MIIGSK Configuration reg */
+#define FEC_MIIGSK_ENR		0x308 /* MIIGSK Enable reg */
 
 #else
 

include/linux/fec.h

+/* include/linux/fec.h
+ *
+ * Copyright (c) 2009 Orex Computed Radiography
+ *   Baruch Siach <baruch@tkos.co.il>
+ *
+ * Header file for the FEC platform data
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#ifndef __LINUX_FEC_H__
+#define __LINUX_FEC_H__
+
+#include <linux/phy.h>
+
+struct fec_platform_data {
+	phy_interface_t phy;
+};
+
+#endif