Merge branches 'at91', 'bcmring', 'ep93xx', 'iop', 'misc', 'nomadik', 'omap',...

Merge branches 'at91', 'bcmring', 'ep93xx', 'iop', 'misc', 'nomadik', 'omap', 'pxa', 'spear' and 'versatile' into devel

Conflicts:
	arch/arm/Makefile
	arch/arm/common/Makefile
	arch/arm/mm/Kconfig

Documentation/arm/00-INDEX

@@ -20,6 +20,8 @@ Samsung-S3C24XX
 	- S3C24XX ARM Linux Overview
 Sharp-LH
 	- Linux on Sharp LH79524 and LH7A40X System On a Chip (SOC)
+SPEAr
+	- ST SPEAr platform Linux Overview
 VFP/
 	- Release notes for Linux Kernel Vector Floating Point support code
 empeg/

Documentation/arm/SPEAr/overview.txt

+			SPEAr ARM Linux Overview
+			==========================
+
+Introduction
+------------
+
+  SPEAr (Structured Processor Enhanced Architecture).
+  weblink : http://www.st.com/spear
+
+  The ST Microelectronics SPEAr range of ARM9/CortexA9 System-on-Chip CPUs are
+  supported by the 'spear' platform of ARM Linux. Currently SPEAr300,
+  SPEAr310, SPEAr320 and SPEAr600 SOCs are supported. Support for the SPEAr13XX
+  series is in progress.
+
+  Hierarchy in SPEAr is as follows:
+
+  SPEAr (Platform)
+	- SPEAr3XX (3XX SOC series, based on ARM9)
+		- SPEAr300 (SOC)
+			- SPEAr300_EVB (Evaluation Board)
+		- SPEAr310 (SOC)
+			- SPEAr310_EVB (Evaluation Board)
+		- SPEAr320 (SOC)
+			- SPEAr320_EVB (Evaluation Board)
+	- SPEAr6XX (6XX SOC series, based on ARM9)
+		- SPEAr600 (SOC)
+			- SPEAr600_EVB (Evaluation Board)
+	- SPEAr13XX (13XX SOC series, based on ARM CORTEXA9)
+		- SPEAr1300 (SOC)
+
+  Configuration
+  -------------
+
+  A generic configuration is provided for each machine, and can be used as the
+  default by
+	make spear600_defconfig
+	make spear300_defconfig
+	make spear310_defconfig
+	make spear320_defconfig
+
+  Layout
+  ------
+
+  The common files for multiple machine families (SPEAr3XX, SPEAr6XX and
+  SPEAr13XX) are located in the platform code contained in arch/arm/plat-spear
+  with headers in plat/.
+
+  Each machine series have a directory with name arch/arm/mach-spear followed by
+  series name. Like mach-spear3xx, mach-spear6xx and mach-spear13xx.
+
+  Common file for machines of spear3xx family is mach-spear3xx/spear3xx.c and for
+  spear6xx is mach-spear6xx/spear6xx.c. mach-spear* also contain soc/machine
+  specific files, like spear300.c, spear310.c, spear320.c and spear600.c.
+  mach-spear* also contains board specific files for each machine type.
+
+
+  Document Author
+  ---------------
+
+  Viresh Kumar, (c) 2010 ST Microelectronics

MAINTAINERS

@@ -5229,6 +5229,46 @@ F:	drivers/serial/sunsu.c
 F:	drivers/serial/sunzilog.c
 F:	drivers/serial/sunzilog.h
 
+SPEAR PLATFORM SUPPORT
+M:	Viresh Kumar <viresh.kumar@st.com>
+W:	http://www.st.com/spear
+S:	Maintained
+F:	arch/arm/plat-spear/
+
+SPEAR3XX MACHINE SUPPORT
+M:	Viresh Kumar <viresh.kumar@st.com>
+W:	http://www.st.com/spear
+S:	Maintained
+F:	arch/arm/mach-spear3xx/
+
+SPEAR6XX MACHINE SUPPORT
+M:	Rajeev Kumar <rajeev-dlh.kumar@st.com>
+W:	http://www.st.com/spear
+S:	Maintained
+F:	arch/arm/mach-spear6xx/
+
+SPEAR CLOCK FRAMEWORK SUPPORT
+M:	Viresh Kumar <viresh.kumar@st.com>
+W:	http://www.st.com/spear
+S:	Maintained
+F:	arch/arm/mach-spear*/clock.c
+F:	arch/arm/mach-spear*/include/mach/clkdev.h
+F:	arch/arm/plat-spear/clock.c
+F:	arch/arm/plat-spear/include/plat/clock.h and clkdev.h
+
+SPEAR PAD MULTIPLEXING SUPPORT
+M:	Viresh Kumar <viresh.kumar@st.com>
+W:	http://www.st.com/spear
+S:	Maintained
+F:	arch/arm/plat-spear/include/plat/padmux.h
+F:	arch/arm/plat-spear/padmux.c
+F:	arch/arm/mach-spear*/spear*xx.c
+F:	arch/arm/mach-spear*/include/mach/generic.h
+F:	arch/arm/mach-spear3xx/spear3*0.c
+F:	arch/arm/mach-spear3xx/spear3*0_evb.c
+F:	arch/arm/mach-spear6xx/spear600.c
+F:	arch/arm/mach-spear6xx/spear600_evb.c
+
 SPECIALIX IO8+ MULTIPORT SERIAL CARD DRIVER
 M:	Roger Wolff <R.E.Wolff@BitWizard.nl>
 S:	Supported

arch/arm/Makefile

@@ -175,9 +175,14 @@ machine-$(CONFIG_ARCH_STMP37XX)		:= stmp37xx
 machine-$(CONFIG_ARCH_U300)		:= u300
 machine-$(CONFIG_ARCH_U8500)		:= ux500
 machine-$(CONFIG_ARCH_VERSATILE)	:= versatile
+machine-$(CONFIG_ARCH_VEXPRESS)		:= vexpress
 machine-$(CONFIG_ARCH_W90X900)		:= w90x900
 machine-$(CONFIG_ARCH_NUC93X)		:= nuc93x
 machine-$(CONFIG_FOOTBRIDGE)		:= footbridge
+machine-$(CONFIG_MACH_SPEAR300)		:= spear3xx
+machine-$(CONFIG_MACH_SPEAR310)		:= spear3xx
+machine-$(CONFIG_MACH_SPEAR320)		:= spear3xx
+machine-$(CONFIG_MACH_SPEAR600)		:= spear6xx
 
 # Platform directory name.  This list is sorted alphanumerically
 # by CONFIG_* macro name.
@@ -192,6 +197,8 @@ plat-$(CONFIG_PLAT_PXA)		:= pxa
 plat-$(CONFIG_PLAT_S3C24XX)	:= s3c24xx samsung
 plat-$(CONFIG_PLAT_S5PC1XX)	:= s5pc1xx samsung
 plat-$(CONFIG_PLAT_S5P)		:= s5p samsung
+plat-$(CONFIG_PLAT_SPEAR)	:= spear
+plat-$(CONFIG_PLAT_VERSATILE)	:= versatile
 
 ifeq ($(CONFIG_ARCH_EBSA110),y)
 # This is what happens if you forget the IOCS16 line.

arch/arm/boot/compressed/Makefile

@@ -65,6 +65,7 @@ SEDFLAGS	= s/TEXT_START/$(ZTEXTADDR)/;s/BSS_START/$(ZBSSADDR)/
 
 suffix_$(CONFIG_KERNEL_GZIP) = gzip
 suffix_$(CONFIG_KERNEL_LZO)  = lzo
+suffix_$(CONFIG_KERNEL_LZMA) = lzma
 
 targets       := vmlinux vmlinux.lds \
 		 piggy.$(suffix_y) piggy.$(suffix_y).o \

arch/arm/boot/compressed/decompress.c

@@ -40,6 +40,10 @@ extern void error(char *);
 #include "../../../../lib/decompress_unlzo.c"
 #endif
 
+#ifdef CONFIG_KERNEL_LZMA
+#include "../../../../lib/decompress_unlzma.c"
+#endif
+
 void do_decompress(u8 *input, int len, u8 *output, void (*error)(char *x))
 {
 	decompress(input, len, NULL, NULL, output, NULL, error);

arch/arm/boot/compressed/piggy.lzma.S

+	.section .piggydata,#alloc
+	.globl	input_data
+input_data:
+	.incbin	"arch/arm/boot/compressed/piggy.lzma"
+	.globl	input_data_end
+input_data_end:

arch/arm/common/Kconfig

@@ -12,10 +12,10 @@ config ARM_VIC_NR
 	  The maximum number of VICs available in the system, for
 	  power management.
 
-config ICST525
+config ICST
 	bool
 
-config ICST307
+config PL330
 	bool
 
 config SA1111
@@ -40,3 +40,4 @@ config SHARP_SCOOP
 
 config COMMON_CLKDEV
 	bool
+	select HAVE_CLK

arch/arm/common/Makefile

@@ -4,8 +4,8 @@
 
 obj-$(CONFIG_ARM_GIC)		+= gic.o
 obj-$(CONFIG_ARM_VIC)		+= vic.o
-obj-$(CONFIG_ICST525)		+= icst525.o
-obj-$(CONFIG_ICST307)		+= icst307.o
+obj-$(CONFIG_ICST)		+= icst.o
+obj-$(CONFIG_PL330)		+= pl330.o
 obj-$(CONFIG_SA1111)		+= sa1111.o
 obj-$(CONFIG_PCI_HOST_VIA82C505) += via82c505.o
 obj-$(CONFIG_DMABOUNCE)		+= dmabounce.o

arch/arm/common/clkdev.c

@@ -52,12 +52,13 @@ static struct clk *clk_find(const char *dev_id, const char *con_id)
 				continue;
 			match += 1;
 		}
-		if (match == 0)
-			continue;
 
 		if (match > best) {
 			clk = p->clk;
+			if (match != 3)
 				best = match;
+			else
+				break;
 		}
 	}
 	return clk;

arch/arm/common/icst307.c → arch/arm/common/icst.c

@@ -17,29 +17,35 @@
 #include <linux/module.h>
 #include <linux/kernel.h>
 
-#include <asm/hardware/icst307.h>
+#include <asm/hardware/icst.h>
 
 /*
  * Divisors for each OD setting.
  */
-static unsigned char s2div[8] = { 10, 2, 8, 4, 5, 7, 3, 6 };
+const unsigned char icst307_s2div[8] = { 10, 2, 8, 4, 5, 7, 3, 6 };
+const unsigned char icst525_s2div[8] = { 10, 2, 8, 4, 5, 7, 9, 6 };
+EXPORT_SYMBOL(icst307_s2div);
+EXPORT_SYMBOL(icst525_s2div);
 
-unsigned long icst307_khz(const struct icst307_params *p, struct icst307_vco vco)
+unsigned long icst_hz(const struct icst_params *p, struct icst_vco vco)
 {
-	return p->ref * 2 * (vco.v + 8) / ((vco.r + 2) * s2div[vco.s]);
+	return p->ref * 2 * (vco.v + 8) / ((vco.r + 2) * p->s2div[vco.s]);
 }
 
-EXPORT_SYMBOL(icst307_khz);
+EXPORT_SYMBOL(icst_hz);
 
 /*
  * Ascending divisor S values.
  */
-static unsigned char idx2s[8] = { 1, 6, 3, 4, 7, 5, 2, 0 };
+const unsigned char icst307_idx2s[8] = { 1, 6, 3, 4, 7, 5, 2, 0 };
+const unsigned char icst525_idx2s[8] = { 1, 3, 4, 7, 5, 2, 6, 0 };
+EXPORT_SYMBOL(icst307_idx2s);
+EXPORT_SYMBOL(icst525_idx2s);
 
-struct icst307_vco
-icst307_khz_to_vco(const struct icst307_params *p, unsigned long freq)
+struct icst_vco
+icst_hz_to_vco(const struct icst_params *p, unsigned long freq)
 {
-	struct icst307_vco vco = { .s = 1, .v = p->vd_max, .r = p->rd_max };
+	struct icst_vco vco = { .s = 1, .v = p->vd_max, .r = p->rd_max };
 	unsigned long f;
 	unsigned int i = 0, rd, best = (unsigned int)-1;
 
@@ -48,19 +54,16 @@ icst307_khz_to_vco(const struct icst307_params *p, unsigned long freq)
 	 * that the PLL output is within spec.
 	 */
 	do {
-		f = freq * s2div[idx2s[i]];
+		f = freq * p->s2div[p->idx2s[i]];
 
-		/*
-		 * f must be between 6MHz and 200MHz (3.3 or 5V)
-		 */
-		if (f > 6000 && f <= p->vco_max)
+		if (f > p->vco_min && f <= p->vco_max)
 			break;
-	} while (i < ARRAY_SIZE(idx2s));
+	} while (i < 8);
 
-	if (i >= ARRAY_SIZE(idx2s))
+	if (i >= 8)
 		return vco;
 
-	vco.s = idx2s[i];
+	vco.s = p->idx2s[i];
 
 	/*
 	 * Now find the closest divisor combination
@@ -94,68 +97,4 @@ icst307_khz_to_vco(const struct icst307_params *p, unsigned long freq)
 	return vco;
 }
 
-EXPORT_SYMBOL(icst307_khz_to_vco);
-
-struct icst307_vco
-icst307_ps_to_vco(const struct icst307_params *p, unsigned long period)
-{
-	struct icst307_vco vco = { .s = 1, .v = p->vd_max, .r = p->rd_max };
-	unsigned long f, ps;
-	unsigned int i = 0, rd, best = (unsigned int)-1;
-
-	ps = 1000000000UL / p->vco_max;
-
-	/*
-	 * First, find the PLL output divisor such
-	 * that the PLL output is within spec.
-	 */
-	do {
-		f = period / s2div[idx2s[i]];
-
-		/*
-		 * f must be between 6MHz and 200MHz (3.3 or 5V)
-		 */
-		if (f >= ps && f < 1000000000UL / 6000 + 1)
-			break;
-	} while (i < ARRAY_SIZE(idx2s));
-
-	if (i >= ARRAY_SIZE(idx2s))
-		return vco;
-
-	vco.s = idx2s[i];
-
-	ps = 500000000UL / p->ref;
-
-	/*
-	 * Now find the closest divisor combination
-	 * which gives a PLL output of 'f'.
-	 */
-	for (rd = p->rd_min; rd <= p->rd_max; rd++) {
-		unsigned long f_in_div, f_pll;
-		unsigned int vd;
-		int f_diff;
-
-		f_in_div = ps * rd;
-
-		vd = (f_in_div + f / 2) / f;
-		if (vd < p->vd_min || vd > p->vd_max)
-			continue;
-
-		f_pll = (f_in_div + vd / 2) / vd;
-		f_diff = f_pll - f;
-		if (f_diff < 0)
-			f_diff = -f_diff;
-
-		if ((unsigned)f_diff < best) {
-			vco.v = vd - 8;
-			vco.r = rd - 2;
-			if (f_diff == 0)
-				break;
-			best = f_diff;
-		}
-	}
-
-	return vco;
-}
-
-EXPORT_SYMBOL(icst307_ps_to_vco);
+EXPORT_SYMBOL(icst_hz_to_vco);

arch/arm/common/icst525.c

-/*
- *  linux/arch/arm/common/icst525.c
- *
- *  Copyright (C) 2003 Deep Blue Solutions, Ltd, All Rights Reserved.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- *  Support functions for calculating clocks/divisors for the ICST525
- *  clock generators.  See http://www.icst.com/ for more information
- *  on these devices.
- */
-#include <linux/module.h>
-#include <linux/kernel.h>
-
-#include <asm/hardware/icst525.h>
-
-/*
- * Divisors for each OD setting.
- */
-static unsigned char s2div[8] = { 10, 2, 8, 4, 5, 7, 9, 6 };
-
-unsigned long icst525_khz(const struct icst525_params *p, struct icst525_vco vco)
-{
-	return p->ref * 2 * (vco.v + 8) / ((vco.r + 2) * s2div[vco.s]);
-}
-
-EXPORT_SYMBOL(icst525_khz);
-
-/*
- * Ascending divisor S values.
- */
-static unsigned char idx2s[] = { 1, 3, 4, 7, 5, 2, 6, 0 };
-
-struct icst525_vco
-icst525_khz_to_vco(const struct icst525_params *p, unsigned long freq)
-{
-	struct icst525_vco vco = { .s = 1, .v = p->vd_max, .r = p->rd_max };
-	unsigned long f;
-	unsigned int i = 0, rd, best = (unsigned int)-1;
-
-	/*
-	 * First, find the PLL output divisor such
-	 * that the PLL output is within spec.
-	 */
-	do {
-		f = freq * s2div[idx2s[i]];
-
-		/*
-		 * f must be between 10MHz and
-		 *  320MHz (5V) or 200MHz (3V)
-		 */
-		if (f > 10000 && f <= p->vco_max)
-			break;
-	} while (i < ARRAY_SIZE(idx2s));
-
-	if (i >= ARRAY_SIZE(idx2s))
-		return vco;
-
-	vco.s = idx2s[i];
-
-	/*
-	 * Now find the closest divisor combination
-	 * which gives a PLL output of 'f'.
-	 */
-	for (rd = p->rd_min; rd <= p->rd_max; rd++) {
-		unsigned long fref_div, f_pll;
-		unsigned int vd;
-		int f_diff;
-
-		fref_div = (2 * p->ref) / rd;
-
-		vd = (f + fref_div / 2) / fref_div;
-		if (vd < p->vd_min || vd > p->vd_max)
-			continue;
-
-		f_pll = fref_div * vd;
-		f_diff = f_pll - f;
-		if (f_diff < 0)
-			f_diff = -f_diff;
-
-		if ((unsigned)f_diff < best) {
-			vco.v = vd - 8;
-			vco.r = rd - 2;
-			if (f_diff == 0)
-				break;
-			best = f_diff;
-		}
-	}
-
-	return vco;
-}
-
-EXPORT_SYMBOL(icst525_khz_to_vco);
-
-struct icst525_vco
-icst525_ps_to_vco(const struct icst525_params *p, unsigned long period)
-{
-	struct icst525_vco vco = { .s = 1, .v = p->vd_max, .r = p->rd_max };
-	unsigned long f, ps;
-	unsigned int i = 0, rd, best = (unsigned int)-1;
-
-	ps = 1000000000UL / p->vco_max;
-
-	/*
-	 * First, find the PLL output divisor such
-	 * that the PLL output is within spec.
-	 */
-	do {
-		f = period / s2div[idx2s[i]];
-
-		/*
-		 * f must be between 10MHz and
-		 *  320MHz (5V) or 200MHz (3V)
-		 */
-		if (f >= ps && f < 100000)
-			break;
-	} while (i < ARRAY_SIZE(idx2s));
-
-	if (i >= ARRAY_SIZE(idx2s))
-		return vco;
-
-	vco.s = idx2s[i];
-
-	ps = 500000000UL / p->ref;
-
-	/*
-	 * Now find the closest divisor combination
-	 * which gives a PLL output of 'f'.
-	 */
-	for (rd = p->rd_min; rd <= p->rd_max; rd++) {
-		unsigned long f_in_div, f_pll;
-		unsigned int vd;
-		int f_diff;
-
-		f_in_div = ps * rd;
-
-		vd = (f_in_div + f / 2) / f;
-		if (vd < p->vd_min || vd > p->vd_max)
-			continue;
-
-		f_pll = (f_in_div + vd / 2) / vd;
-		f_diff = f_pll - f;
-		if (f_diff < 0)
-			f_diff = -f_diff;
-
-		if ((unsigned)f_diff < best) {
-			vco.v = vd - 8;
-			vco.r = rd - 2;
-			if (f_diff == 0)
-				break;
-			best = f_diff;
-		}
-	}
-
-	return vco;
-}
-
-EXPORT_SYMBOL(icst525_ps_to_vco);

arch/arm/common/vic.c

@@ -273,6 +273,46 @@ static struct irq_chip vic_chip = {
 	.set_wake	= vic_set_wake,
 };
 
+static void __init vic_disable(void __iomem *base)
+{
+	writel(0, base + VIC_INT_SELECT);
+	writel(0, base + VIC_INT_ENABLE);
+	writel(~0, base + VIC_INT_ENABLE_CLEAR);
+	writel(0, base + VIC_IRQ_STATUS);
+	writel(0, base + VIC_ITCR);
+	writel(~0, base + VIC_INT_SOFT_CLEAR);
+}
+
+static void __init vic_clear_interrupts(void __iomem *base)
+{
+	unsigned int i;
+
+	writel(0, base + VIC_PL190_VECT_ADDR);
+	for (i = 0; i < 19; i++) {
+		unsigned int value;
+
+		value = readl(base + VIC_PL190_VECT_ADDR);
+		writel(value, base + VIC_PL190_VECT_ADDR);
+	}
+}
+
+static void __init vic_set_irq_sources(void __iomem *base,
+				unsigned int irq_start, u32 vic_sources)
+{
+	unsigned int i;
+
+	for (i = 0; i < 32; i++) {
+		if (vic_sources & (1 << i)) {
+			unsigned int irq = irq_start + i;
+
+			set_irq_chip(irq, &vic_chip);
+			set_irq_chip_data(irq, base);
+			set_irq_handler(irq, handle_level_irq);
+			set_irq_flags(irq, IRQF_VALID | IRQF_PROBE);
+		}
+	}
+}
+
 /*
  * The PL190 cell from ARM has been modified by ST to handle 64 interrupts.
  * The original cell has 32 interrupts, while the modified one has 64,
@@ -287,13 +327,7 @@ static void __init vic_init_st(void __iomem *base, unsigned int irq_start,
 	int vic_2nd_block = ((unsigned long)base & ~PAGE_MASK) != 0;
 
 	/* Disable all interrupts initially. */
-
-	writel(0, base + VIC_INT_SELECT);
-	writel(0, base + VIC_INT_ENABLE);
-	writel(~0, base + VIC_INT_ENABLE_CLEAR);
-	writel(0, base + VIC_IRQ_STATUS);
-	writel(0, base + VIC_ITCR);
-	writel(~0, base + VIC_INT_SOFT_CLEAR);
+	vic_disable(base);
 
 	/*
 	 * Make sure we clear all existing interrupts. The vector registers
@@ -302,13 +336,8 @@ static void __init vic_init_st(void __iomem *base, unsigned int irq_start,
 	 * the second base address, which is 0x20 in the page
 	 */
 	if (vic_2nd_block) {
-		writel(0, base + VIC_PL190_VECT_ADDR);
-		for (i = 0; i < 19; i++) {
-			unsigned int value;
+		vic_clear_interrupts(base);
 
-			value = readl(base + VIC_PL190_VECT_ADDR);
-			writel(value, base + VIC_PL190_VECT_ADDR);
-		}
 		/* ST has 16 vectors as well, but we don't enable them by now */
 		for (i = 0; i < 16; i++) {
 			void __iomem *reg = base + VIC_VECT_CNTL0 + (i * 4);
@@ -318,16 +347,7 @@ static void __init vic_init_st(void __iomem *base, unsigned int irq_start,
 		writel(32, base + VIC_PL190_DEF_VECT_ADDR);
 	}
 
-	for (i = 0; i < 32; i++) {
-		if (vic_sources & (1 << i)) {
-			unsigned int irq = irq_start + i;
-
-			set_irq_chip(irq, &vic_chip);
-			set_irq_chip_data(irq, base);
-			set_irq_handler(irq, handle_level_irq);
-			set_irq_flags(irq, IRQF_VALID | IRQF_PROBE);
-		}
-	}
+	vic_set_irq_sources(base, irq_start, vic_sources);
 }
 
 /**
@@ -365,37 +385,14 @@ void __init vic_init(void __iomem *base, unsigned int irq_start,
 	}
 
 	/* Disable all interrupts initially. */
+	vic_disable(base);
 
-	writel(0, base + VIC_INT_SELECT);
-	writel(0, base + VIC_INT_ENABLE);
-	writel(~0, base + VIC_INT_ENABLE_CLEAR);
-	writel(0, base + VIC_IRQ_STATUS);
-	writel(0, base + VIC_ITCR);
-	writel(~0, base + VIC_INT_SOFT_CLEAR);
-
-	/*
-	 * Make sure we clear all existing interrupts
-	 */
-	writel(0, base + VIC_PL190_VECT_ADDR);
-	for (i = 0; i < 19; i++) {
-		unsigned int value;
-
-		value = readl(base + VIC_PL190_VECT_ADDR);
-		writel(value, base + VIC_PL190_VECT_ADDR);
-	}
+	/* Make sure we clear all existing interrupts */
+	vic_clear_interrupts(base);
 
 	vic_init2(base);
 
-	for (i = 0; i < 32; i++) {
-		if (vic_sources & (1 << i)) {
-			unsigned int irq = irq_start + i;
-
-			set_irq_chip(irq, &vic_chip);
-			set_irq_chip_data(irq, base);
-			set_irq_handler(irq, handle_level_irq);
-			set_irq_flags(irq, IRQF_VALID | IRQF_PROBE);
-		}
-	}
+	vic_set_irq_sources(base, irq_start, vic_sources);
 
 	vic_pm_register(base, irq_start, resume_sources);
 }

arch/arm/include/asm/hardware/arm_timer.h

 #ifndef __ASM_ARM_HARDWARE_ARM_TIMER_H
 #define __ASM_ARM_HARDWARE_ARM_TIMER_H
 
-#define TIMER_LOAD	0x00
-#define TIMER_VALUE	0x04
-#define TIMER_CTRL	0x08
-#define TIMER_CTRL_ONESHOT	(1 << 0)
-#define TIMER_CTRL_32BIT	(1 << 1)
-#define TIMER_CTRL_DIV1		(0 << 2)
-#define TIMER_CTRL_DIV16	(1 << 2)
-#define TIMER_CTRL_DIV256	(2 << 2)
-#define TIMER_CTRL_IE		(1 << 5)	/* Interrupt Enable (versatile only) */
-#define TIMER_CTRL_PERIODIC	(1 << 6)
-#define TIMER_CTRL_ENABLE	(1 << 7)
+/*
+ * ARM timer implementation, found in Integrator, Versatile and Realview
+ * platforms.  Not all platforms support all registers and bits in these
+ * registers, so we mark them with A for Integrator AP, C for Integrator
+ * CP, V for Versatile and R for Realview.
+ *
+ * Integrator AP has 16-bit timers, Integrator CP, Versatile and Realview
+ * can have 16-bit or 32-bit selectable via a bit in the control register.
+ */
+#define TIMER_LOAD	0x00			/* ACVR rw */
+#define TIMER_VALUE	0x04			/* ACVR ro */
+#define TIMER_CTRL	0x08			/* ACVR rw */
+#define TIMER_CTRL_ONESHOT	(1 << 0)	/*  CVR */
+#define TIMER_CTRL_32BIT	(1 << 1)	/*  CVR */
+#define TIMER_CTRL_DIV1		(0 << 2)	/* ACVR */
+#define TIMER_CTRL_DIV16	(1 << 2)	/* ACVR */
+#define TIMER_CTRL_DIV256	(2 << 2)	/* ACVR */
+#define TIMER_CTRL_IE		(1 << 5)	/*   VR */
+#define TIMER_CTRL_PERIODIC	(1 << 6)	/* ACVR */
+#define TIMER_CTRL_ENABLE	(1 << 7)	/* ACVR */
 
-#define TIMER_INTCLR	0x0c
-#define TIMER_RIS	0x10
-#define TIMER_MIS	0x14
-#define TIMER_BGLOAD	0x18
+#define TIMER_INTCLR	0x0c			/* ACVR wo */
+#define TIMER_RIS	0x10			/*  CVR ro */
+#define TIMER_MIS	0x14			/*  CVR ro */
+#define TIMER_BGLOAD	0x18			/*  CVR rw */
 
 #endif

arch/arm/include/asm/hardware/cache-l2x0.h

@@ -21,6 +21,9 @@
 #define __ASM_ARM_HARDWARE_L2X0_H
 
 #define L2X0_CACHE_ID			0x000
+#define   L2X0_CACHE_ID_PART_MASK	(0xf << 6)
+#define   L2X0_CACHE_ID_PART_L210	(1 << 6)
+#define   L2X0_CACHE_ID_PART_L310	(3 << 6)
 #define L2X0_CACHE_TYPE			0x004
 #define L2X0_CTRL			0x100
 #define L2X0_AUX_CTRL			0x104

arch/arm/include/asm/hardware/icst307.h → arch/arm/include/asm/hardware/icst.h

 /*
- *  arch/arm/include/asm/hardware/icst307.h
+ *  arch/arm/include/asm/hardware/icst.h
  *
  *  Copyright (C) 2003 Deep Blue Solutions, Ltd, All Rights Reserved.
  *
@@ -7,32 +7,53 @@
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  *
- *  Support functions for calculating clocks/divisors for the ICS307
+ *  Support functions for calculating clocks/divisors for the ICST
  *  clock generators.  See http://www.icst.com/ for more information
  *  on these devices.
- *
- *  This file is similar to the icst525.h file
  */
-#ifndef ASMARM_HARDWARE_ICST307_H
-#define ASMARM_HARDWARE_ICST307_H
+#ifndef ASMARM_HARDWARE_ICST_H
+#define ASMARM_HARDWARE_ICST_H
 
-struct icst307_params {
+struct icst_params {
 	unsigned long	ref;
 	unsigned long	vco_max;	/* inclusive */
+	unsigned long	vco_min;	/* exclusive */
 	unsigned short	vd_min;		/* inclusive */
 	unsigned short	vd_max;		/* inclusive */
 	unsigned char	rd_min;		/* inclusive */
 	unsigned char	rd_max;		/* inclusive */
+	const unsigned char *s2div;	/* chip specific s2div array */
+	const unsigned char *idx2s;	/* chip specific idx2s array */
 };
 
-struct icst307_vco {
+struct icst_vco {
 	unsigned short	v;
 	unsigned char	r;
 	unsigned char	s;
 };
 
-unsigned long icst307_khz(const struct icst307_params *p, struct icst307_vco vco);
-struct icst307_vco icst307_khz_to_vco(const struct icst307_params *p, unsigned long freq);
-struct icst307_vco icst307_ps_to_vco(const struct icst307_params *p, unsigned long period);
+unsigned long icst_hz(const struct icst_params *p, struct icst_vco vco);
+struct icst_vco icst_hz_to_vco(const struct icst_params *p, unsigned long freq);
+
+/*
+ * ICST307 VCO frequency must be between 6MHz and 200MHz (3.3 or 5V).
+ * This frequency is pre-output divider.
+ */
+#define ICST307_VCO_MIN	6000000
+#define ICST307_VCO_MAX	200000000
+
+extern const unsigned char icst307_s2div[];
+extern const unsigned char icst307_idx2s[];
+
+/*
+ * ICST525 VCO frequency must be between 10MHz and 200MHz (3V) or 320MHz (5V).
+ * This frequency is pre-output divider.
+ */
+#define ICST525_VCO_MIN		10000000
+#define ICST525_VCO_MAX_3V	200000000
+#define ICST525_VCO_MAX_5V	320000000
+
+extern const unsigned char icst525_s2div[];
+extern const unsigned char icst525_idx2s[];
 
 #endif

arch/arm/include/asm/hardware/icst525.h

-/*
- *  arch/arm/include/asm/hardware/icst525.h
- *
- *  Copyright (C) 2003 Deep Blue Solutions, Ltd, All Rights Reserved.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- *  Support functions for calculating clocks/divisors for the ICST525
- *  clock generators.  See http://www.icst.com/ for more information
- *  on these devices.
- */
-#ifndef ASMARM_HARDWARE_ICST525_H
-#define ASMARM_HARDWARE_ICST525_H
-
-struct icst525_params {
-	unsigned long	ref;
-	unsigned long	vco_max;	/* inclusive */
-	unsigned short	vd_min;		/* inclusive */
-	unsigned short	vd_max;		/* inclusive */
-	unsigned char	rd_min;		/* inclusive */
-	unsigned char	rd_max;		/* inclusive */
-};
-
-struct icst525_vco {
-	unsigned short	v;
-	unsigned char	r;
-	unsigned char	s;
-};
-
-unsigned long icst525_khz(const struct icst525_params *p, struct icst525_vco vco);
-struct icst525_vco icst525_khz_to_vco(const struct icst525_params *p, unsigned long freq);
-struct icst525_vco icst525_ps_to_vco(const struct icst525_params *p, unsigned long period);
-
-#endif

arch/arm/include/asm/hardware/pl330.h

+/* linux/include/asm/hardware/pl330.h
+ *
+ * Copyright (C) 2010 Samsung Electronics Co. Ltd.
+ *	Jaswinder Singh <jassi.brar@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#ifndef __PL330_CORE_H
+#define __PL330_CORE_H
+
+#define PL330_MAX_CHAN		8
+#define PL330_MAX_IRQS		32
+#define PL330_MAX_PERI		32
+
+enum pl330_srccachectrl {
+	SCCTRL0 = 0, /* Noncacheable and nonbufferable */
+	SCCTRL1, /* Bufferable only */
+	SCCTRL2, /* Cacheable, but do not allocate */
+	SCCTRL3, /* Cacheable and bufferable, but do not allocate */
+	SINVALID1,
+	SINVALID2,
+	SCCTRL6, /* Cacheable write-through, allocate on reads only */
+	SCCTRL7, /* Cacheable write-back, allocate on reads only */
+};
+
+enum pl330_dstcachectrl {
+	DCCTRL0 = 0, /* Noncacheable and nonbufferable */
+	DCCTRL1, /* Bufferable only */
+	DCCTRL2, /* Cacheable, but do not allocate */
+	DCCTRL3, /* Cacheable and bufferable, but do not allocate */
+	DINVALID1 = 8,
+	DINVALID2,
+	DCCTRL6, /* Cacheable write-through, allocate on writes only */
+	DCCTRL7, /* Cacheable write-back, allocate on writes only */
+};
+
+/* Populated by the PL330 core driver for DMA API driver's info */
+struct pl330_config {
+	u32	periph_id;
+	u32	pcell_id;
+#define DMAC_MODE_NS	(1 << 0)
+	unsigned int	mode;
+	unsigned int	data_bus_width:10; /* In number of bits */
+	unsigned int	data_buf_dep:10;
+	unsigned int	num_chan:4;
+	unsigned int	num_peri:6;
+	u32		peri_ns;
+	unsigned int	num_events:6;
+	u32		irq_ns;
+};
+
+/* Handle to the DMAC provided to the PL330 core */
+struct pl330_info {
+	/* Owning device */
+	struct device *dev;
+	/* Size of MicroCode buffers for each channel. */
+	unsigned mcbufsz;
+	/* ioremap'ed address of PL330 registers. */
+	void __iomem	*base;
+	/* Client can freely use it. */
+	void	*client_data;
+	/* PL330 core data, Client must not touch it. */
+	void	*pl330_data;
+	/* Populated by the PL330 core driver during pl330_add */
+	struct pl330_config	pcfg;
+	/*
+	 * If the DMAC has some reset mechanism, then the
+	 * client may want to provide pointer to the method.
+	 */
+	void (*dmac_reset)(struct pl330_info *pi);
+};
+
+enum pl330_byteswap {
+	SWAP_NO = 0,
+	SWAP_2,
+	SWAP_4,
+	SWAP_8,
+	SWAP_16,
+};
+
+/**
+ * Request Configuration.
+ * The PL330 core does not modify this and uses the last
+ * working configuration if the request doesn't provide any.
+ *
+ * The Client may want to provide this info only for the
+ * first request and a request with new settings.
+ */
+struct pl330_reqcfg {
+	/* Address Incrementing */
+	unsigned dst_inc:1;
+	unsigned src_inc:1;
+
+	/*
+	 * For now, the SRC & DST protection levels
+	 * and burst size/length are assumed same.
+	 */
+	bool nonsecure;
+	bool privileged;
+	bool insnaccess;
+	unsigned brst_len:5;
+	unsigned brst_size:3; /* in power of 2 */
+
+	enum pl330_dstcachectrl dcctl;
+	enum pl330_srccachectrl scctl;
+	enum pl330_byteswap swap;
+};
+
+/*
+ * One cycle of DMAC operation.
+ * There may be more than one xfer in a request.
+ */
+struct pl330_xfer {
+	u32 src_addr;
+	u32 dst_addr;
+	/* Size to xfer */
+	u32 bytes;
+	/*
+	 * Pointer to next xfer in the list.
+	 * The last xfer in the req must point to NULL.
+	 */
+	struct pl330_xfer *next;
+};
+
+/* The xfer callbacks are made with one of these arguments. */
+enum pl330_op_err {
+	/* The all xfers in the request were success. */
+	PL330_ERR_NONE,
+	/* If req aborted due to global error. */
+	PL330_ERR_ABORT,
+	/* If req failed due to problem with Channel. */
+	PL330_ERR_FAIL,
+};
+
+enum pl330_reqtype {
+	MEMTOMEM,
+	MEMTODEV,
+	DEVTOMEM,
+	DEVTODEV,
+};
+
+/* A request defining Scatter-Gather List ending with NULL xfer. */
+struct pl330_req {
+	enum pl330_reqtype rqtype;
+	/* Index of peripheral for the xfer. */
+	unsigned peri:5;
+	/* Unique token for this xfer, set by the client. */
+	void *token;
+	/* Callback to be called after xfer. */
+	void (*xfer_cb)(void *token, enum pl330_op_err err);
+	/* If NULL, req will be done at last set parameters. */
+	struct pl330_reqcfg *cfg;
+	/* Pointer to first xfer in the request. */
+	struct pl330_xfer *x;
+};
+
+/*
+ * To know the status of the channel and DMAC, the client
+ * provides a pointer to this structure. The PL330 core
+ * fills it with current information.
+ */
+struct pl330_chanstatus {
+	/*
+	 * If the DMAC engine halted due to some error,
+	 * the client should remove-add DMAC.
+	 */
+	bool dmac_halted;
+	/*
+	 * If channel is halted due to some error,
+	 * the client should ABORT/FLUSH and START the channel.
+	 */
+	bool faulting;
+	/* Location of last load */
+	u32 src_addr;
+	/* Location of last store */
+	u32 dst_addr;
+	/*
+	 * Pointer to the currently active req, NULL if channel is
+	 * inactive, even though the requests may be present.
+	 */
+	struct pl330_req *top_req;
+	/* Pointer to req waiting second in the queue if any. */
+	struct pl330_req *wait_req;
+};
+
+enum pl330_chan_op {
+	/* Start the channel */
+	PL330_OP_START,
+	/* Abort the active xfer */
+	PL330_OP_ABORT,
+	/* Stop xfer and flush queue */
+	PL330_OP_FLUSH,
+};
+
+extern int pl330_add(struct pl330_info *);
+extern void pl330_del(struct pl330_info *pi);
+extern int pl330_update(const struct pl330_info *pi);
+extern void pl330_release_channel(void *ch_id);
+extern void *pl330_request_channel(const struct pl330_info *pi);
+extern int pl330_chan_status(void *ch_id, struct pl330_chanstatus *pstatus);
+extern int pl330_chan_ctrl(void *ch_id, enum pl330_chan_op op);
+extern int pl330_submit_req(void *ch_id, struct pl330_req *r);
+
+#endif	/* __PL330_CORE_H */

arch/arm/include/asm/hardware/sp810.h

+/*
+ * arch/arm/include/asm/hardware/sp810.h
+ *
+ * ARM PrimeXsys System Controller SP810 header file
+ *
+ * Copyright (C) 2009 ST Microelectronics
+ * Viresh Kumar<viresh.kumar@st.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#ifndef __ASM_ARM_SP810_H
+#define __ASM_ARM_SP810_H
+
+#include <linux/io.h>
+
+/* sysctl registers offset */
+#define SCCTRL			0x000
+#define SCSYSSTAT		0x004
+#define SCIMCTRL		0x008
+#define SCIMSTAT		0x00C
+#define SCXTALCTRL		0x010
+#define SCPLLCTRL		0x014
+#define SCPLLFCTRL		0x018
+#define SCPERCTRL0		0x01C
+#define SCPERCTRL1		0x020
+#define SCPEREN			0x024
+#define SCPERDIS		0x028
+#define SCPERCLKEN		0x02C
+#define SCPERSTAT		0x030
+#define SCSYSID0		0xEE0
+#define SCSYSID1		0xEE4
+#define SCSYSID2		0xEE8
+#define SCSYSID3		0xEEC
+#define SCITCR			0xF00
+#define SCITIR0			0xF04
+#define SCITIR1			0xF08
+#define SCITOR			0xF0C
+#define SCCNTCTRL		0xF10
+#define SCCNTDATA		0xF14
+#define SCCNTSTEP		0xF18
+#define SCPERIPHID0		0xFE0
+#define SCPERIPHID1		0xFE4
+#define SCPERIPHID2		0xFE8
+#define SCPERIPHID3		0xFEC
+#define SCPCELLID0		0xFF0
+#define SCPCELLID1		0xFF4
+#define SCPCELLID2		0xFF8
+#define SCPCELLID3		0xFFC
+
+static inline void sysctl_soft_reset(void __iomem *base)
+{
+	/* writing any value to SCSYSSTAT reg will reset system */
+	writel(0, base + SCSYSSTAT);
+}
+
+#endif	/* __ASM_ARM_SP810_H */

arch/arm/include/asm/mach/pci.h

@@ -8,10 +8,16 @@
  * published by the Free Software Foundation.
  */
 
+#ifndef __ASM_MACH_PCI_H
+#define __ASM_MACH_PCI_H
+
 struct pci_sys_data;
 struct pci_bus;
 
 struct hw_pci {
+#ifdef CONFIG_PCI_DOMAINS
+	int		domain;
+#endif
 	struct list_head buses;
 	int		nr_controllers;
 	int		(*setup)(int nr, struct pci_sys_data *);
@@ -26,6 +32,9 @@ struct hw_pci {
  * Per-controller structure
  */
 struct pci_sys_data {
+#ifdef CONFIG_PCI_DOMAINS
+	int		domain;
+#endif
 	struct list_head node;
 	int		busnr;		/* primary bus number			*/
 	u64		mem_offset;	/* bus->cpu memory mapping offset	*/
@@ -70,3 +79,5 @@ extern int pci_v3_setup(int nr, struct pci_sys_data *);
 extern struct pci_bus *pci_v3_scan_bus(int nr, struct pci_sys_data *);
 extern void pci_v3_preinit(void);
 extern void pci_v3_postinit(void);
+
+#endif /* __ASM_MACH_PCI_H */

arch/arm/include/asm/mach/time.h

@@ -38,7 +38,7 @@ struct sys_timer {
 	void			(*init)(void);
 	void			(*suspend)(void);
 	void			(*resume)(void);
-#ifndef CONFIG_GENERIC_TIME
+#ifdef CONFIG_ARCH_USES_GETTIMEOFFSET
 	unsigned long		(*offset)(void);
 #endif
 };

arch/arm/include/asm/pci.h

@@ -4,8 +4,23 @@
 #ifdef __KERNEL__
 #include <asm-generic/pci-dma-compat.h>
 
+#include <asm/mach/pci.h> /* for pci_sys_data */
 #include <mach/hardware.h> /* for PCIBIOS_MIN_* */
 
+#ifdef CONFIG_PCI_DOMAINS
+static inline int pci_domain_nr(struct pci_bus *bus)
+{
+	struct pci_sys_data *root = bus->sysdata;
+
+	return root->domain;
+}
+
+static inline int pci_proc_domain(struct pci_bus *bus)
+{
+	return pci_domain_nr(bus);
+}
+#endif /* CONFIG_PCI_DOMAINS */
+
 #ifdef CONFIG_PCI_HOST_ITE8152
 /* ITE bridge requires setting latency timer to avoid early bus access
    termination by PIC bus mater devices

arch/arm/include/asm/pgtable.h

@@ -314,7 +314,7 @@ static inline pte_t pte_mkspecial(pte_t pte) { return pte; }
 	__pgprot_modify(prot, L_PTE_MT_MASK, L_PTE_MT_UNCACHED)
 #define pgprot_writecombine(prot) \
 	__pgprot_modify(prot, L_PTE_MT_MASK, L_PTE_MT_BUFFERABLE)
-#if __LINUX_ARM_ARCH__ >= 7
+#ifdef CONFIG_ARM_DMA_MEM_BUFFERABLE
 #define pgprot_dmacoherent(prot) \
 	__pgprot_modify(prot, L_PTE_MT_MASK|L_PTE_EXEC, L_PTE_MT_BUFFERABLE)
 #else

arch/arm/mach-integrator/common.h

-extern void integrator_time_init(unsigned long, unsigned int);
-extern unsigned long integrator_gettimeoffset(void);

arch/arm/mach-nomadik/clock.h

@@ -11,4 +11,3 @@
 struct clk {
 	unsigned long		rate;
 };
-extern int nmdk_clk_create(struct clk *clk, const char *dev_id);