ARM: sun6i: m9: Convert to DT label based syntax

In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

arch/arm/boot/dts/sun6i-a31-m9.dts

@@ -60,93 +60,91 @@ chosen {
 		bootargs = "earlyprintk console=ttyS0,115200";
 	};
 
-	soc@01c00000 {
-		mmc0: mmc@01c0f000 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_m9>;
-			vmmc-supply = <&reg_vcc3v3>;
-			bus-width = <4>;
-			cd-gpios = <&pio 7 22 GPIO_ACTIVE_HIGH>; /* PH22 */
-			cd-inverted;
-			status = "okay";
-		};
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&led_pins_m9>;
 
-		usbphy: phy@01c19400 {
-			usb1_vbus-supply = <&reg_usb1_vbus>;
-			status = "okay";
+		blue {
+			label = "m9:blue:usr";
+			gpios = <&pio 7 13 GPIO_ACTIVE_HIGH>;
 		};
+	};
+};
 
-		ehci0: usb@01c1a000 {
-			status = "okay";
-		};
+&ehci0 {
+	status = "okay";
+};
 
-		ehci1: usb@01c1b000 {
-			status = "okay";
-		};
+&ehci1 {
+	status = "okay";
+};
 
-		pio: pinctrl@01c20800 {
-			led_pins_m9: led_pins@0 {
-				allwinner,pins = "PH13";
-				allwinner,function = "gpio_out";
-				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-			};
-
-			mmc0_cd_pin_m9: mmc0_cd_pin@0 {
-				allwinner,pins = "PH22";
-				allwinner,function = "gpio_in";
-				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-				allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
-			};
-
-			usb1_vbus_pin_m9: usb1_vbus_pin@0 {
-				allwinner,pins = "PC27";
-				allwinner,function = "gpio_out";
-				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-			};
-		};
+&gmac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac_pins_mii_a>;
+	phy = <&phy1>;
+	phy-mode = "mii";
+	status = "okay";
 
-		uart0: serial@01c28000 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&uart0_pins_a>;
-			status = "okay";
-		};
+	phy1: ethernet-phy@1 {
+		reg = <1>;
+	};
+};
 
-		gmac: ethernet@01c30000 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&gmac_pins_mii_a>;
-			phy = <&phy1>;
-			phy-mode = "mii";
-			status = "okay";
+&ir {
+	pinctrl-names = "default";
+	pinctrl-0 = <&ir_pins_a>;
+	status = "okay";
+};
 
-			phy1: ethernet-phy@1 {
-				reg = <1>;
-			};
-		};
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_m9>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	cd-gpios = <&pio 7 22 GPIO_ACTIVE_HIGH>; /* PH22 */
+	cd-inverted;
+	status = "okay";
+};
 
-		ir@01f02000 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&ir_pins_a>;
-			status = "okay";
-		};
+&pio {
+	led_pins_m9: led_pins@0 {
+		allwinner,pins = "PH13";
+		allwinner,function = "gpio_out";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
 	};
 
-	leds {
-		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&led_pins_m9>;
-
-		blue {
-			label = "m9:blue:usr";
-			gpios = <&pio 7 13 GPIO_ACTIVE_HIGH>;
-		};
+	mmc0_cd_pin_m9: mmc0_cd_pin@0 {
+		allwinner,pins = "PH22";
+		allwinner,function = "gpio_in";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
 	};
 
-	reg_usb1_vbus: usb1-vbus {
-		pinctrl-names = "default";
-		pinctrl-0 = <&usb1_vbus_pin_m9>;
-		gpio = <&pio 2 27 GPIO_ACTIVE_HIGH>;
-		status = "okay";
+	usb1_vbus_pin_m9: usb1_vbus_pin@0 {
+		allwinner,pins = "PC27";
+		allwinner,function = "gpio_out";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
 	};
 };
+
+&reg_usb1_vbus {
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb1_vbus_pin_m9>;
+	gpio = <&pio 2 27 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins_a>;
+	status = "okay";
+};
+
+&usbphy {
+	usb1_vbus-supply = <&reg_usb1_vbus>;
+	status = "okay";
+};