Merge branch 'x86/core' into tracing/textedit

Conflicts:
	arch/x86/Kconfig
	block/blktrace.c
	kernel/irq/handle.c

Semantic conflict:
	kernel/trace/blktrace.c
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Documentation/cputopology.txt

@@ -18,11 +18,11 @@ For an architecture to support this feature, it must define some of
 these macros in include/asm-XXX/topology.h:
 #define topology_physical_package_id(cpu)
 #define topology_core_id(cpu)
-#define topology_thread_siblings(cpu)
-#define topology_core_siblings(cpu)
+#define topology_thread_cpumask(cpu)
+#define topology_core_cpumask(cpu)
 
 The type of **_id is int.
-The type of siblings is cpumask_t.
+The type of siblings is (const) struct cpumask *.
 
 To be consistent on all architectures, include/linux/topology.h
 provides default definitions for any of the above macros that are

Documentation/kernel-parameters.txt

@@ -1320,8 +1320,13 @@ and is between 256 and 4096 characters. It is defined in the file
 
 	memtest=	[KNL,X86] Enable memtest
 			Format: <integer>
-			range: 0,4 : pattern number
 			default : 0 <disable>
+			Specifies the number of memtest passes to be
+			performed. Each pass selects another test
+			pattern from a given set of patterns. Memtest
+			fills the memory with this pattern, validates
+			memory contents and reserves bad memory
+			regions that are detected.
 
 	meye.*=		[HW] Set MotionEye Camera parameters
 			See Documentation/video4linux/meye.txt.

Documentation/x86/boot.txt

@@ -158,7 +158,7 @@ Offset	Proto	Name		Meaning
 0202/4	2.00+	header		Magic signature "HdrS"
 0206/2	2.00+	version		Boot protocol version supported
 0208/4	2.00+	realmode_swtch	Boot loader hook (see below)
-020C/2	2.00+	start_sys	The load-low segment (0x1000) (obsolete)
+020C/2	2.00+	start_sys_seg	The load-low segment (0x1000) (obsolete)
 020E/2	2.00+	kernel_version	Pointer to kernel version string
 0210/1	2.00+	type_of_loader	Boot loader identifier
 0211/1	2.00+	loadflags	Boot protocol option flags
@@ -170,10 +170,11 @@ Offset	Proto	Name		Meaning
 0224/2	2.01+	heap_end_ptr	Free memory after setup end
 0226/2	N/A	pad1		Unused
 0228/4	2.02+	cmd_line_ptr	32-bit pointer to the kernel command line
-022C/4	2.03+	initrd_addr_max	Highest legal initrd address
+022C/4	2.03+	ramdisk_max	Highest legal initrd address
 0230/4	2.05+	kernel_alignment Physical addr alignment required for kernel
 0234/1	2.05+	relocatable_kernel Whether kernel is relocatable or not
-0235/3	N/A	pad2		Unused
+0235/1	N/A	pad2		Unused
+0236/2	N/A	pad3		Unused
 0238/4	2.06+	cmdline_size	Maximum size of the kernel command line
 023C/4	2.07+	hardware_subarch Hardware subarchitecture
 0240/8	2.07+	hardware_subarch_data Subarchitecture-specific data
@@ -299,14 +300,14 @@ Protocol:	2.00+
   e.g. 0x0204 for version 2.04, and 0x0a11 for a hypothetical version
   10.17.
 
-Field name:	readmode_swtch
+Field name:	realmode_swtch
 Type:		modify (optional)
 Offset/size:	0x208/4
 Protocol:	2.00+
 
   Boot loader hook (see ADVANCED BOOT LOADER HOOKS below.)
 
-Field name:	start_sys
+Field name:	start_sys_seg
 Type:		read
 Offset/size:	0x20c/2
 Protocol:	2.00+
@@ -468,7 +469,7 @@ Protocol:	2.02+
   zero, the kernel will assume that your boot loader does not support
   the 2.02+ protocol.
 
-Field name:	initrd_addr_max
+Field name:	ramdisk_max
 Type:		read
 Offset/size:	0x22c/4
 Protocol:	2.03+
@@ -542,7 +543,10 @@ Protocol:	2.08+
 
   The payload may be compressed. The format of both the compressed and
   uncompressed data should be determined using the standard magic
-  numbers. Currently only gzip compressed ELF is used.
+  numbers.  The currently supported compression formats are gzip
+  (magic numbers 1F 8B or 1F 9E), bzip2 (magic number 42 5A) and LZMA
+  (magic number 5D 00).  The uncompressed payload is currently always ELF
+  (magic number 7F 45 4C 46).
   
 Field name:	payload_length
 Type:		read

Documentation/x86/earlyprintk.txt

+
+Mini-HOWTO for using the earlyprintk=dbgp boot option with a
+USB2 Debug port key and a debug cable, on x86 systems.
+
+You need two computers, the 'USB debug key' special gadget and
+and two USB cables, connected like this:
+
+  [host/target] <-------> [USB debug key] <-------> [client/console]
+
+1. There are three specific hardware requirements:
+
+ a.) Host/target system needs to have USB debug port capability.
+
+ You can check this capability by looking at a 'Debug port' bit in
+ the lspci -vvv output:
+
+ # lspci -vvv
+ ...
+ 00:1d.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 (rev 03) (prog-if 20 [EHCI])
+         Subsystem: Lenovo ThinkPad T61
+         Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
+         Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
+         Latency: 0
+         Interrupt: pin D routed to IRQ 19
+         Region 0: Memory at fe227000 (32-bit, non-prefetchable) [size=1K]
+         Capabilities: [50] Power Management version 2
+                 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
+                 Status: D0 PME-Enable- DSel=0 DScale=0 PME+
+         Capabilities: [58] Debug port: BAR=1 offset=00a0
+                            ^^^^^^^^^^^ <==================== [ HERE ]
+	 Kernel driver in use: ehci_hcd
+         Kernel modules: ehci-hcd
+ ...
+
+( If your system does not list a debug port capability then you probably
+  wont be able to use the USB debug key. )
+
+ b.) You also need a Netchip USB debug cable/key:
+
+        http://www.plxtech.com/products/NET2000/NET20DC/default.asp
+
+     This is a small blue plastic connector with two USB connections,
+     it draws power from its USB connections.
+
+ c.) Thirdly, you need a second client/console system with a regular USB port.
+
+2. Software requirements:
+
+ a.) On the host/target system:
+
+    You need to enable the following kernel config option:
+
+      CONFIG_EARLY_PRINTK_DBGP=y
+
+    And you need to add the boot command line: "earlyprintk=dbgp".
+    (If you are using Grub, append it to the 'kernel' line in
+     /etc/grub.conf)
+
+    NOTE: normally earlyprintk console gets turned off once the
+    regular console is alive - use "earlyprintk=dbgp,keep" to keep
+    this channel open beyond early bootup. This can be useful for
+    debugging crashes under Xorg, etc.
+
+ b.) On the client/console system:
+
+    You should enable the following kernel config option:
+
+      CONFIG_USB_SERIAL_DEBUG=y
+
+    On the next bootup with the modified kernel you should
+    get a /dev/ttyUSBx device(s).
+
+    Now this channel of kernel messages is ready to be used: start
+    your favorite terminal emulator (minicom, etc.) and set
+    it up to use /dev/ttyUSB0 - or use a raw 'cat /dev/ttyUSBx' to
+    see the raw output.
+
+ c.) On Nvidia Southbridge based systems: the kernel will try to probe
+     and find out which port has debug device connected.
+
+3. Testing that it works fine:
+
+   You can test the output by using earlyprintk=dbgp,keep and provoking
+   kernel messages on the host/target system. You can provoke a harmless
+   kernel message by for example doing:
+
+     echo h > /proc/sysrq-trigger
+
+   On the host/target system you should see this help line in "dmesg" output:
+
+     SysRq : HELP : loglevel(0-9) reBoot Crashdump terminate-all-tasks(E) memory-full-oom-kill(F) kill-all-tasks(I) saK show-backtrace-all-active-cpus(L) show-memory-usage(M) nice-all-RT-tasks(N) powerOff show-registers(P) show-all-timers(Q) unRaw Sync show-task-states(T) Unmount show-blocked-tasks(W) dump-ftrace-buffer(Z)
+
+   On the client/console system do:
+
+       cat /dev/ttyUSB0
+
+   And you should see the help line above displayed shortly after you've
+   provoked it on the host system.
+
+If it does not work then please ask about it on the linux-kernel@vger.kernel.org
+mailing list or contact the x86 maintainers.

Makefile

@@ -533,8 +533,9 @@ KBUILD_CFLAGS += $(call cc-option,-Wframe-larger-than=${CONFIG_FRAME_WARN})
 endif
 
 # Force gcc to behave correct even for buggy distributions
-# Arch Makefiles may override this setting
+ifndef CONFIG_CC_STACKPROTECTOR
 KBUILD_CFLAGS += $(call cc-option, -fno-stack-protector)
+endif
 
 ifdef CONFIG_FRAME_POINTER
 KBUILD_CFLAGS	+= -fno-omit-frame-pointer -fno-optimize-sibling-calls

arch/alpha/include/asm/statfs.h

 #ifndef _ALPHA_STATFS_H
 #define _ALPHA_STATFS_H
 
+#include <linux/types.h>
+
 /* Alpha is the only 64-bit platform with 32-bit statfs. And doesn't
    even seem to implement statfs64 */
 #define __statfs_word __u32

arch/alpha/include/asm/swab.h

 #ifndef _ALPHA_SWAB_H
 #define _ALPHA_SWAB_H
 
-#include <asm/types.h>
+#include <linux/types.h>
 #include <linux/compiler.h>
 #include <asm/compiler.h>
 

arch/alpha/kernel/irq.c

@@ -55,7 +55,7 @@ int irq_select_affinity(unsigned int irq)
 		cpu = (cpu < (NR_CPUS-1) ? cpu + 1 : 0);
 	last_cpu = cpu;
 
-	irq_desc[irq].affinity = cpumask_of_cpu(cpu);
+	cpumask_copy(irq_desc[irq].affinity, cpumask_of(cpu));
 	irq_desc[irq].chip->set_affinity(irq, cpumask_of(cpu));
 	return 0;
 }

arch/alpha/mm/init.c

@@ -189,9 +189,21 @@ callback_init(void * kernel_end)
 
 	if (alpha_using_srm) {
 		static struct vm_struct console_remap_vm;
-		unsigned long vaddr = VMALLOC_START;
+		unsigned long nr_pages = 0;
+		unsigned long vaddr;
 		unsigned long i, j;
 
+		/* calculate needed size */
+		for (i = 0; i < crb->map_entries; ++i)
+			nr_pages += crb->map[i].count;
+
+		/* register the vm area */
+		console_remap_vm.flags = VM_ALLOC;
+		console_remap_vm.size = nr_pages << PAGE_SHIFT;
+		vm_area_register_early(&console_remap_vm, PAGE_SIZE);
+
+		vaddr = (unsigned long)console_remap_vm.addr;
+
 		/* Set up the third level PTEs and update the virtual
 		   addresses of the CRB entries.  */
 		for (i = 0; i < crb->map_entries; ++i) {
@@ -213,12 +225,6 @@ callback_init(void * kernel_end)
 				vaddr += PAGE_SIZE;
 			}
 		}
-
-		/* Let vmalloc know that we've allocated some space.  */
-		console_remap_vm.flags = VM_ALLOC;
-		console_remap_vm.addr = (void *) VMALLOC_START;
-		console_remap_vm.size = vaddr - VMALLOC_START;
-		vmlist = &console_remap_vm;
 	}
 
 	callback_init_done = 1;

arch/arm/include/asm/a.out.h

@@ -2,7 +2,7 @@
 #define __ARM_A_OUT_H__
 
 #include <linux/personality.h>
-#include <asm/types.h>
+#include <linux/types.h>
 
 struct exec
 {

arch/arm/include/asm/setup.h

@@ -14,7 +14,7 @@
 #ifndef __ASMARM_SETUP_H
 #define __ASMARM_SETUP_H
 
-#include <asm/types.h>
+#include <linux/types.h>
 
 #define COMMAND_LINE_SIZE 1024
 

arch/arm/include/asm/swab.h

@@ -16,7 +16,7 @@
 #define __ASM_ARM_SWAB_H
 
 #include <linux/compiler.h>
-#include <asm/types.h>
+#include <linux/types.h>
 
 #if !defined(__STRICT_ANSI__) || defined(__KERNEL__)
 #  define __SWAB_64_THRU_32__

arch/arm/kernel/irq.c

@@ -104,6 +104,11 @@ static struct irq_desc bad_irq_desc = {
 	.lock = __SPIN_LOCK_UNLOCKED(bad_irq_desc.lock),
 };
 
+#ifdef CONFIG_CPUMASK_OFFSTACK
+/* We are not allocating bad_irq_desc.affinity or .pending_mask */
+#error "ARM architecture does not support CONFIG_CPUMASK_OFFSTACK."
+#endif
+
 /*
  * do_IRQ handles all hardware IRQ's.  Decoded IRQs should not
  * come via this function.  Instead, they should provide their
@@ -161,7 +166,7 @@ void __init init_IRQ(void)
 		irq_desc[irq].status |= IRQ_NOREQUEST | IRQ_NOPROBE;
 
 #ifdef CONFIG_SMP
-	bad_irq_desc.affinity = CPU_MASK_ALL;
+	cpumask_setall(bad_irq_desc.affinity);
 	bad_irq_desc.cpu = smp_processor_id();
 #endif
 	init_arch_irq();
@@ -191,15 +196,16 @@ void migrate_irqs(void)
 		struct irq_desc *desc = irq_desc + i;
 
 		if (desc->cpu == cpu) {
-			unsigned int newcpu = any_online_cpu(desc->affinity);
-
-			if (newcpu == NR_CPUS) {
+			unsigned int newcpu = cpumask_any_and(desc->affinity,
+							      cpu_online_mask);
+			if (newcpu >= nr_cpu_ids) {
 				if (printk_ratelimit())
 					printk(KERN_INFO "IRQ%u no longer affine to CPU%u\n",
 					       i, cpu);
 
-				cpus_setall(desc->affinity);
-				newcpu = any_online_cpu(desc->affinity);
+				cpumask_setall(desc->affinity);
+				newcpu = cpumask_any_and(desc->affinity,
+							 cpu_online_mask);
 			}
 
 			route_irq(desc, i, newcpu);

arch/arm/kernel/vmlinux.lds.S

@@ -65,6 +65,7 @@ SECTIONS
 #endif
 		. = ALIGN(4096);
 		__per_cpu_start = .;
+			*(.data.percpu.page_aligned)
 			*(.data.percpu)
 			*(.data.percpu.shared_aligned)
 		__per_cpu_end = .;

arch/arm/oprofile/op_model_mpcore.c

@@ -263,7 +263,7 @@ static void em_route_irq(int irq, unsigned int cpu)
 	const struct cpumask *mask = cpumask_of(cpu);
 
 	spin_lock_irq(&desc->lock);
-	desc->affinity = *mask;
+	cpumask_copy(desc->affinity, mask);
 	desc->chip->set_affinity(irq, mask);
 	spin_unlock_irq(&desc->lock);
 }

arch/avr32/Kconfig

@@ -181,7 +181,7 @@ source "kernel/Kconfig.preempt"
 config QUICKLIST
 	def_bool y
 
-config HAVE_ARCH_BOOTMEM_NODE
+config HAVE_ARCH_BOOTMEM
 	def_bool n
 
 config ARCH_HAVE_MEMORY_PRESENT

arch/avr32/include/asm/swab.h

@@ -4,7 +4,7 @@
 #ifndef __ASM_AVR32_SWAB_H
 #define __ASM_AVR32_SWAB_H
 
-#include <asm/types.h>
+#include <linux/types.h>
 #include <linux/compiler.h>
 
 #define __SWAB_64_THRU_32__

arch/blackfin/include/asm/swab.h

 #ifndef _BLACKFIN_SWAB_H
 #define _BLACKFIN_SWAB_H
 
-#include <asm/types.h>
+#include <linux/types.h>
 #include <linux/compiler.h>
 
 #if defined(__GNUC__) && !defined(__STRICT_ANSI__) || defined(__KERNEL__)

arch/blackfin/kernel/irqchip.c

@@ -70,6 +70,11 @@ static struct irq_desc bad_irq_desc = {
 #endif
 };
 
+#ifdef CONFIG_CPUMASK_OFFSTACK
+/* We are not allocating a variable-sized bad_irq_desc.affinity */
+#error "Blackfin architecture does not support CONFIG_CPUMASK_OFFSTACK."
+#endif
+
 int show_interrupts(struct seq_file *p, void *v)
 {
 	int i = *(loff_t *) v, j;

arch/h8300/include/asm/swab.h

 #ifndef _H8300_SWAB_H
 #define _H8300_SWAB_H
 
-#include <asm/types.h>
+#include <linux/types.h>
 
 #if defined(__GNUC__) && !defined(__STRICT_ANSI__) || defined(__KERNEL__)
 #  define __SWAB_64_THRU_32__

arch/ia64/include/asm/fpu.h

@@ -6,8 +6,6 @@
  *	David Mosberger-Tang <davidm@hpl.hp.com>
  */
 
-#include <asm/types.h>
-
 /* floating point status register: */
 #define FPSR_TRAP_VD	(1 << 0)	/* invalid op trap disabled */
 #define FPSR_TRAP_DD	(1 << 1)	/* denormal trap disabled */

arch/ia64/include/asm/gcc_intrin.h

@@ -6,6 +6,7 @@
  * Copyright (C) 2002,2003 Suresh Siddha <suresh.b.siddha@intel.com>
  */
 
+#include <linux/types.h>
 #include <linux/compiler.h>
 
 /* define this macro to get some asm stmts included in 'c' files */

arch/ia64/include/asm/intrinsics.h

@@ -10,6 +10,7 @@
 
 #ifndef __ASSEMBLY__
 
+#include <linux/types.h>
 /* include compiler specific intrinsics */
 #include <asm/ia64regs.h>
 #ifdef __INTEL_COMPILER

arch/ia64/include/asm/kvm.h

@@ -21,8 +21,7 @@
  *
  */
 
-#include <asm/types.h>
-
+#include <linux/types.h>
 #include <linux/ioctl.h>
 
 /* Select x86 specific features in <linux/kvm.h> */

arch/ia64/include/asm/percpu.h

@@ -27,12 +27,12 @@ extern void *per_cpu_init(void);
 
 #else /* ! SMP */
 
-#define PER_CPU_ATTRIBUTES	__attribute__((__section__(".data.percpu")))
-
 #define per_cpu_init()				(__phys_per_cpu_start)
 
 #endif	/* SMP */
 
+#define PER_CPU_BASE_SECTION ".data.percpu"
+
 /*
  * Be extremely careful when taking the address of this variable!  Due to virtual
  * remapping, it is different from the canonical address returned by __get_cpu_var(var)!

arch/ia64/include/asm/swab.h

@@ -6,7 +6,7 @@
  *	David Mosberger-Tang <davidm@hpl.hp.com>, Hewlett-Packard Co.
  */
 
-#include <asm/types.h>
+#include <linux/types.h>
 #include <asm/intrinsics.h>
 #include <linux/compiler.h>
 

arch/ia64/include/asm/topology.h

@@ -84,7 +84,7 @@ void build_cpu_to_node_map(void);
 	.child			= NULL,			\
 	.groups			= NULL,			\
 	.min_interval		= 8,			\
-	.max_interval		= 8*(min(num_online_cpus(), 32)), \
+	.max_interval		= 8*(min(num_online_cpus(), 32U)), \
 	.busy_factor		= 64,			\
 	.imbalance_pct		= 125,			\
 	.cache_nice_tries	= 2,			\

arch/ia64/include/asm/uv/uv.h

+#ifndef _ASM_IA64_UV_UV_H
+#define _ASM_IA64_UV_UV_H
+
+#include <asm/system.h>
+#include <asm/sn/simulator.h>
+
+static inline int is_uv_system(void)
+{
+	/* temporary support for running on hardware simulator */
+	return IS_MEDUSA() || ia64_platform_is("uv");
+}
+
+#endif	/* _ASM_IA64_UV_UV_H */

arch/ia64/kernel/acpi.c

@@ -199,6 +199,10 @@ char *__init __acpi_map_table(unsigned long phys_addr, unsigned long size)
 	return __va(phys_addr);
 }
 
+void __init __acpi_unmap_table(char *map, unsigned long size)
+{
+}
+
 /* --------------------------------------------------------------------------
                             Boot-time Table Parsing
    -------------------------------------------------------------------------- */

arch/ia64/kernel/iosapic.c

@@ -880,7 +880,7 @@ iosapic_unregister_intr (unsigned int gsi)
 	if (iosapic_intr_info[irq].count == 0) {
 #ifdef CONFIG_SMP
 		/* Clear affinity */
-		cpus_setall(idesc->affinity);
+		cpumask_setall(idesc->affinity);
 #endif
 		/* Clear the interrupt information */
 		iosapic_intr_info[irq].dest = 0;

arch/ia64/kernel/irq.c

@@ -103,7 +103,7 @@ static char irq_redir [NR_IRQS]; // = { [0 ... NR_IRQS-1] = 1 };
 void set_irq_affinity_info (unsigned int irq, int hwid, int redir)
 {
 	if (irq < NR_IRQS) {
-		cpumask_copy(&irq_desc[irq].affinity,
+		cpumask_copy(irq_desc[irq].affinity,
 			     cpumask_of(cpu_logical_id(hwid)));
 		irq_redir[irq] = (char) (redir & 0xff);
 	}
@@ -148,7 +148,7 @@ static void migrate_irqs(void)
 		if (desc->status == IRQ_PER_CPU)
 			continue;
 
-		if (cpumask_any_and(&irq_desc[irq].affinity, cpu_online_mask)
+		if (cpumask_any_and(irq_desc[irq].affinity, cpu_online_mask)
 		    >= nr_cpu_ids) {
 			/*
 			 * Save it for phase 2 processing

arch/ia64/kernel/irq_ia64.c

@@ -493,11 +493,13 @@ ia64_handle_irq (ia64_vector vector, struct pt_regs *regs)
 	saved_tpr = ia64_getreg(_IA64_REG_CR_TPR);
 	ia64_srlz_d();
 	while (vector != IA64_SPURIOUS_INT_VECTOR) {
+		struct irq_desc *desc = irq_to_desc(vector);
+
 		if (unlikely(IS_LOCAL_TLB_FLUSH(vector))) {
 			smp_local_flush_tlb();
-			kstat_this_cpu.irqs[vector]++;
+			kstat_incr_irqs_this_cpu(vector, desc);
 		} else if (unlikely(IS_RESCHEDULE(vector)))
-			kstat_this_cpu.irqs[vector]++;
+			kstat_incr_irqs_this_cpu(vector, desc);
 		else {
 			int irq = local_vector_to_irq(vector);
 
@@ -551,11 +553,13 @@ void ia64_process_pending_intr(void)
 	  * Perform normal interrupt style processing
 	  */
 	while (vector != IA64_SPURIOUS_INT_VECTOR) {
+		struct irq_desc *desc = irq_to_desc(vector);
+
 		if (unlikely(IS_LOCAL_TLB_FLUSH(vector))) {
 			smp_local_flush_tlb();
-			kstat_this_cpu.irqs[vector]++;
+			kstat_incr_irqs_this_cpu(vector, desc);
 		} else if (unlikely(IS_RESCHEDULE(vector)))
-			kstat_this_cpu.irqs[vector]++;
+			kstat_incr_irqs_this_cpu(vector, desc);
 		else {
 			struct pt_regs *old_regs = set_irq_regs(NULL);
 			int irq = local_vector_to_irq(vector);

arch/ia64/kernel/msi_ia64.c

@@ -75,7 +75,7 @@ static void ia64_set_msi_irq_affinity(unsigned int irq,
 	msg.data = data;
 
 	write_msi_msg(irq, &msg);
-	irq_desc[irq].affinity = cpumask_of_cpu(cpu);
+	cpumask_copy(irq_desc[irq].affinity, cpumask_of(cpu));
 }
 #endif /* CONFIG_SMP */
 
@@ -187,7 +187,7 @@ static void dmar_msi_set_affinity(unsigned int irq, const struct cpumask *mask)
 	msg.address_lo |= MSI_ADDR_DESTID_CPU(cpu_physical_id(cpu));
 
 	dmar_msi_write(irq, &msg);
-	irq_desc[irq].affinity = *mask;
+	cpumask_copy(irq_desc[irq].affinity, mask);
 }
 #endif /* CONFIG_SMP */
 

arch/ia64/kernel/vmlinux.lds.S

@@ -219,6 +219,7 @@ SECTIONS
   .data.percpu PERCPU_ADDR : AT(__phys_per_cpu_start - LOAD_OFFSET)
 	{
 		__per_cpu_start = .;
+		*(.data.percpu.page_aligned)
 		*(.data.percpu)
 		*(.data.percpu.shared_aligned)
 		__per_cpu_end = .;

arch/ia64/sn/kernel/msi_sn.c

@@ -205,7 +205,7 @@ static void sn_set_msi_irq_affinity(unsigned int irq,
 	msg.address_lo = (u32)(bus_addr & 0x00000000ffffffff);
 
 	write_msi_msg(irq, &msg);
-	irq_desc[irq].affinity = *cpu_mask;
+	cpumask_copy(irq_desc[irq].affinity, cpu_mask);
 }
 #endif /* CONFIG_SMP */
 

arch/mips/include/asm/irq.h

@@ -66,7 +66,7 @@ extern void smtc_forward_irq(unsigned int irq);
  */
 #define IRQ_AFFINITY_HOOK(irq)						\
 do {									\
-    if (!cpu_isset(smp_processor_id(), irq_desc[irq].affinity)) {	\
+    if (!cpumask_test_cpu(smp_processor_id(), irq_desc[irq].affinity)) {\
 	smtc_forward_irq(irq);						\
 	irq_exit();							\
 	return;								\

arch/mips/include/asm/sigcontext.h

@@ -9,6 +9,7 @@
 #ifndef _ASM_SIGCONTEXT_H
 #define _ASM_SIGCONTEXT_H
 
+#include <linux/types.h>
 #include <asm/sgidefs.h>
 
 #if _MIPS_SIM == _MIPS_SIM_ABI32

arch/mips/include/asm/swab.h

@@ -9,7 +9,7 @@
 #define _ASM_SWAB_H
 
 #include <linux/compiler.h>
-#include <asm/types.h>
+#include <linux/types.h>
 
 #define __SWAB_64_THRU_32__
 

arch/mips/kernel/irq-gic.c

@@ -187,7 +187,7 @@ static void gic_set_affinity(unsigned int irq, const struct cpumask *cpumask)
 		set_bit(irq, pcpu_masks[first_cpu(tmp)].pcpu_mask);
 
 	}
-	irq_desc[irq].affinity = *cpumask;
+	cpumask_copy(irq_desc[irq].affinity, cpumask);
 	spin_unlock_irqrestore(&gic_lock, flags);
 
 }

arch/mips/kernel/smtc.c

@@ -686,7 +686,7 @@ void smtc_forward_irq(unsigned int irq)
 	 * and efficiency, we just pick the easiest one to find.
 	 */
 
-	target = first_cpu(irq_desc[irq].affinity);
+	target = cpumask_first(irq_desc[irq].affinity);
 
 	/*
 	 * We depend on the platform code to have correctly processed
@@ -921,11 +921,13 @@ void ipi_decode(struct smtc_ipi *pipi)
 	struct clock_event_device *cd;
 	void *arg_copy = pipi->arg;
 	int type_copy = pipi->type;
+	int irq = MIPS_CPU_IRQ_BASE + 1;
+
 	smtc_ipi_nq(&freeIPIq, pipi);
 	switch (type_copy) {
 	case SMTC_CLOCK_TICK:
 		irq_enter();
-		kstat_this_cpu.irqs[MIPS_CPU_IRQ_BASE + 1]++;
+		kstat_incr_irqs_this_cpu(irq, irq_to_desc(irq));
 		cd = &per_cpu(mips_clockevent_device, cpu);
 		cd->event_handler(cd);
 		irq_exit();

arch/mips/mti-malta/malta-smtc.c

@@ -116,7 +116,7 @@ struct plat_smp_ops msmtc_smp_ops = {
 
 void plat_set_irq_affinity(unsigned int irq, const struct cpumask *affinity)
 {
-	cpumask_t tmask = *affinity;
+	cpumask_t tmask;
 	int cpu = 0;
 	void smtc_set_irq_affinity(unsigned int irq, cpumask_t aff);
 
@@ -139,11 +139,12 @@ void plat_set_irq_affinity(unsigned int irq, const struct cpumask *affinity)
 	 * be made to forward to an offline "CPU".
 	 */
 
+	cpumask_copy(&tmask, affinity);
 	for_each_cpu(cpu, affinity) {
 		if ((cpu_data[cpu].vpe_id != 0) || !cpu_online(cpu))
 			cpu_clear(cpu, tmask);
 	}
-	irq_desc[irq].affinity = tmask;
+	cpumask_copy(irq_desc[irq].affinity, &tmask);
 
 	if (cpus_empty(tmask))
 		/*

arch/mips/sgi-ip22/ip22-int.c

@@ -155,7 +155,7 @@ static void indy_buserror_irq(void)
 	int irq = SGI_BUSERR_IRQ;
 
 	irq_enter();
-	kstat_this_cpu.irqs[irq]++;
+	kstat_incr_irqs_this_cpu(irq, irq_to_desc(irq));
 	ip22_be_interrupt(irq);
 	irq_exit();
 }

arch/mips/sgi-ip22/ip22-time.c

@@ -122,7 +122,7 @@ void indy_8254timer_irq(void)
 	char c;
 
 	irq_enter();
-	kstat_this_cpu.irqs[irq]++;
+	kstat_incr_irqs_this_cpu(irq, irq_to_desc(irq));
 	printk(KERN_ALERT "Oops, got 8254 interrupt.\n");
 	ArcRead(0, &c, 1, &cnt);
 	ArcEnterInteractiveMode();

arch/mips/sibyte/bcm1480/smp.c

@@ -178,9 +178,10 @@ struct plat_smp_ops bcm1480_smp_ops = {
 void bcm1480_mailbox_interrupt(void)
 {
 	int cpu = smp_processor_id();
+	int irq = K_BCM1480_INT_MBOX_0_0;
 	unsigned int action;
 
-	kstat_this_cpu.irqs[K_BCM1480_INT_MBOX_0_0]++;
+	kstat_incr_irqs_this_cpu(irq, irq_to_desc(irq));
 	/* Load the mailbox register to figure out what we're supposed to do */
 	action = (__raw_readq(mailbox_0_regs[cpu]) >> 48) & 0xffff;
 

arch/mips/sibyte/sb1250/smp.c

@@ -166,9 +166,10 @@ struct plat_smp_ops sb_smp_ops = {
 void sb1250_mailbox_interrupt(void)
 {
 	int cpu = smp_processor_id();
+	int irq = K_INT_MBOX_0;
 	unsigned int action;
 
-	kstat_this_cpu.irqs[K_INT_MBOX_0]++;
+	kstat_incr_irqs_this_cpu(irq, irq_to_desc(irq));
 	/* Load the mailbox register to figure out what we're supposed to do */
 	action = (____raw_readq(mailbox_regs[cpu]) >> 48) & 0xffff;
 

arch/mn10300/kernel/mn10300-watchdog.c

@@ -130,6 +130,7 @@ void watchdog_interrupt(struct pt_regs *regs, enum exception_code excep)
 	 * the stack NMI-atomically, it's safe to use smp_processor_id().
 	 */
 	int sum, cpu = smp_processor_id();
+	int irq = NMIIRQ;
 	u8 wdt, tmp;
 
 	wdt = WDCTR & ~WDCTR_WDCNE;
@@ -138,7 +139,7 @@ void watchdog_interrupt(struct pt_regs *regs, enum exception_code excep)
 	NMICR = NMICR_WDIF;
 
 	nmi_count(cpu)++;
-	kstat_this_cpu.irqs[NMIIRQ]++;
+	kstat_incr_irqs_this_cpu(irq, irq_to_desc(irq));
 	sum = irq_stat[cpu].__irq_count;
 
 	if (last_irq_sums[cpu] == sum) {

arch/parisc/include/asm/pdc.h

@@ -336,10 +336,11 @@
 #define NUM_PDC_RESULT	32
 
 #if !defined(__ASSEMBLY__)
-#ifdef __KERNEL__
 
 #include <linux/types.h>
 
+#ifdef __KERNEL__
+
 extern int pdc_type;
 
 /* Values for pdc_type */

arch/parisc/include/asm/swab.h

 #ifndef _PARISC_SWAB_H
 #define _PARISC_SWAB_H
 
-#include <asm/types.h>
+#include <linux/types.h>
 #include <linux/compiler.h>
 
 #define __SWAB_64_THRU_32__

arch/parisc/kernel/irq.c

@@ -120,7 +120,7 @@ int cpu_check_affinity(unsigned int irq, cpumask_t *dest)
 	if (CHECK_IRQ_PER_CPU(irq)) {
 		/* Bad linux design decision.  The mask has already
 		 * been set; we must reset it */
-		irq_desc[irq].affinity = CPU_MASK_ALL;
+		cpumask_setall(irq_desc[irq].affinity);
 		return -EINVAL;
 	}
 
@@ -136,7 +136,7 @@ static void cpu_set_affinity_irq(unsigned int irq, const struct cpumask *dest)
 	if (cpu_check_affinity(irq, dest))
 		return;
 
-	irq_desc[irq].affinity = *dest;
+	cpumask_copy(irq_desc[irq].affinity, dest);
 }
 #endif
 
@@ -295,7 +295,7 @@ int txn_alloc_irq(unsigned int bits_wide)
 unsigned long txn_affinity_addr(unsigned int irq, int cpu)
 {
 #ifdef CONFIG_SMP
-	irq_desc[irq].affinity = cpumask_of_cpu(cpu);
+	cpumask_copy(irq_desc[irq].affinity, cpumask_of(cpu));
 #endif
 
 	return per_cpu(cpu_data, cpu).txn_addr;
@@ -352,7 +352,7 @@ void do_cpu_irq_mask(struct pt_regs *regs)
 	irq = eirr_to_irq(eirr_val);
 
 #ifdef CONFIG_SMP
-	dest = irq_desc[irq].affinity;
+	cpumask_copy(&dest, irq_desc[irq].affinity);
 	if (CHECK_IRQ_PER_CPU(irq_desc[irq].status) &&
 	    !cpu_isset(smp_processor_id(), dest)) {
 		int cpu = first_cpu(dest);

arch/powerpc/include/asm/bootx.h

@@ -9,7 +9,7 @@
 #ifndef __ASM_BOOTX_H__
 #define __ASM_BOOTX_H__
 
-#include <asm/types.h>
+#include <linux/types.h>
 
 #ifdef macintosh
 #include <Types.h>

arch/powerpc/include/asm/elf.h

@@ -7,7 +7,7 @@
 #include <asm/string.h>
 #endif
 
-#include <asm/types.h>
+#include <linux/types.h>
 #include <asm/ptrace.h>
 #include <asm/cputable.h>
 #include <asm/auxvec.h>

arch/powerpc/include/asm/kvm.h

@@ -20,7 +20,7 @@
 #ifndef __LINUX_KVM_POWERPC_H
 #define __LINUX_KVM_POWERPC_H
 
-#include <asm/types.h>
+#include <linux/types.h>
 
 struct kvm_regs {
 	__u64 pc;

arch/powerpc/include/asm/ps3fb.h

@@ -19,6 +19,7 @@
 #ifndef _ASM_POWERPC_PS3FB_H_
 #define _ASM_POWERPC_PS3FB_H_
 
+#include <linux/types.h>
 #include <linux/ioctl.h>
 
 /* ioctl */

arch/powerpc/include/asm/spu_info.h

@@ -23,9 +23,10 @@
 #ifndef _SPU_INFO_H
 #define _SPU_INFO_H
 
+#include <linux/types.h>
+
 #ifdef __KERNEL__
 #include <asm/spu.h>
-#include <linux/types.h>
 #else
 struct mfc_cq_sr {
 	__u64 mfc_cq_data0_RW;

arch/powerpc/include/asm/swab.h

@@ -8,7 +8,7 @@
  * 2 of the License, or (at your option) any later version.
  */
 
-#include <asm/types.h>
+#include <linux/types.h>
 #include <linux/compiler.h>
 
 #ifdef __GNUC__

arch/powerpc/kernel/irq.c

@@ -231,7 +231,7 @@ void fixup_irqs(cpumask_t map)
 		if (irq_desc[irq].status & IRQ_PER_CPU)
 			continue;
 
-		cpus_and(mask, irq_desc[irq].affinity, map);
+		cpumask_and(&mask, irq_desc[irq].affinity, &map);
 		if (any_online_cpu(mask) == NR_CPUS) {
 			printk("Breaking affinity for irq %i\n", irq);
 			mask = map;

arch/powerpc/kernel/vmlinux.lds.S

@@ -184,6 +184,7 @@ SECTIONS
 	. = ALIGN(PAGE_SIZE);
 	.data.percpu  : AT(ADDR(.data.percpu) - LOAD_OFFSET) {
 		__per_cpu_start = .;
+		*(.data.percpu.page_aligned)
 		*(.data.percpu)
 		*(.data.percpu.shared_aligned)
 		__per_cpu_end = .;

arch/powerpc/platforms/86xx/gef_sbc610.c

@@ -142,6 +142,10 @@ static void __init gef_sbc610_nec_fixup(struct pci_dev *pdev)
 {
 	unsigned int val;
 
+	/* Do not do the fixup on other platforms! */
+	if (!machine_is(gef_sbc610))
+		return;
+
 	printk(KERN_INFO "Running NEC uPD720101 Fixup\n");
 
 	/* Ensure ports 1, 2, 3, 4 & 5 are enabled */

arch/powerpc/platforms/pseries/xics.c

@@ -153,9 +153,10 @@ static int get_irq_server(unsigned int virq, unsigned int strict_check)
 {
 	int server;
 	/* For the moment only implement delivery to all cpus or one cpu */
-	cpumask_t cpumask = irq_desc[virq].affinity;
+	cpumask_t cpumask;
 	cpumask_t tmp = CPU_MASK_NONE;
 
+	cpumask_copy(&cpumask, irq_desc[virq].affinity);
 	if (!distribute_irqs)
 		return default_server;
 
@@ -869,7 +870,7 @@ void xics_migrate_irqs_away(void)
 		       virq, cpu);
 
 		/* Reset affinity to all cpus */
-		irq_desc[virq].affinity = CPU_MASK_ALL;
+		cpumask_setall(irq_desc[virq].affinity);
 		desc->chip->set_affinity(virq, cpu_all_mask);
 unlock:
 		spin_unlock_irqrestore(&desc->lock, flags);

arch/powerpc/sysdev/mpic.c

@@ -566,9 +566,10 @@ static void __init mpic_scan_ht_pics(struct mpic *mpic)
 #ifdef CONFIG_SMP
 static int irq_choose_cpu(unsigned int virt_irq)
 {
-	cpumask_t mask = irq_desc[virt_irq].affinity;
+	cpumask_t mask;
 	int cpuid;
 
+	cpumask_copy(&mask, irq_desc[virt_irq].affinity);
 	if (cpus_equal(mask, CPU_MASK_ALL)) {
 		static int irq_rover;
 		static DEFINE_SPINLOCK(irq_rover_lock);

arch/sparc/kernel/irq_64.c

@@ -252,9 +252,10 @@ struct irq_handler_data {
 #ifdef CONFIG_SMP
 static int irq_choose_cpu(unsigned int virt_irq)
 {
-	cpumask_t mask = irq_desc[virt_irq].affinity;
+	cpumask_t mask;
 	int cpuid;
 
+	cpumask_copy(&mask, irq_desc[virt_irq].affinity);
 	if (cpus_equal(mask, CPU_MASK_ALL)) {
 		static int irq_rover;
 		static DEFINE_SPINLOCK(irq_rover_lock);
@@ -796,7 +797,7 @@ void fixup_irqs(void)
 		    !(irq_desc[irq].status & IRQ_PER_CPU)) {
 			if (irq_desc[irq].chip->set_affinity)
 				irq_desc[irq].chip->set_affinity(irq,
-					&irq_desc[irq].affinity);
+					irq_desc[irq].affinity);
 		}
 		spin_unlock_irqrestore(&irq_desc[irq].lock, flags);
 	}

arch/sparc/kernel/time_64.c

@@ -729,7 +729,7 @@ void timer_interrupt(int irq, struct pt_regs *regs)
 
 	irq_enter();
 
-	kstat_this_cpu.irqs[0]++;
+	kstat_incr_irqs_this_cpu(0, irq_to_desc(0));
 
 	if (unlikely(!evt->event_handler)) {
 		printk(KERN_WARNING

arch/x86/Kconfig.debug

@@ -7,7 +7,7 @@ source "lib/Kconfig.debug"
 
 config STRICT_DEVMEM
 	bool "Filter access to /dev/mem"
-	help
+	---help---
 	  If this option is disabled, you allow userspace (root) access to all
 	  of memory, including kernel and userspace memory. Accidental
 	  access to this is obviously disastrous, but specific access can
@@ -25,7 +25,7 @@ config STRICT_DEVMEM
 config X86_VERBOSE_BOOTUP
 	bool "Enable verbose x86 bootup info messages"
 	default y
-	help
+	---help---
 	  Enables the informational output from the decompression stage
 	  (e.g. bzImage) of the boot. If you disable this you will still
 	  see errors. Disable this if you want silent bootup.
@@ -33,7 +33,7 @@ config X86_VERBOSE_BOOTUP
 config EARLY_PRINTK
 	bool "Early printk" if EMBEDDED
 	default y
-	help
+	---help---
 	  Write kernel log output directly into the VGA buffer or to a serial
 	  port.
 
@@ -47,7 +47,7 @@ config EARLY_PRINTK_DBGP
 	bool "Early printk via EHCI debug port"
 	default n
 	depends on EARLY_PRINTK && PCI
-	help
+	---help---
 	  Write kernel log output directly into the EHCI debug port.
 
 	  This is useful for kernel debugging when your machine crashes very
@@ -59,14 +59,14 @@ config EARLY_PRINTK_DBGP
 config DEBUG_STACKOVERFLOW
 	bool "Check for stack overflows"
 	depends on DEBUG_KERNEL
-	help
+	---help---
 	  This option will cause messages to be printed if free stack space
 	  drops below a certain limit.
 
 config DEBUG_STACK_USAGE
 	bool "Stack utilization instrumentation"
 	depends on DEBUG_KERNEL
-	help
+	---help---
 	  Enables the display of the minimum amount of free stack which each
 	  task has ever had available in the sysrq-T and sysrq-P debug output.
 
@@ -75,7 +75,7 @@ config DEBUG_STACK_USAGE
 config DEBUG_PAGEALLOC
 	bool "Debug page memory allocations"
 	depends on DEBUG_KERNEL
-	help
+	---help---
 	  Unmap pages from the kernel linear mapping after free_pages().
 	  This results in a large slowdown, but helps to find certain types
 	  of memory corruptions.
@@ -83,9 +83,9 @@ config DEBUG_PAGEALLOC
 config DEBUG_PER_CPU_MAPS
 	bool "Debug access to per_cpu maps"
 	depends on DEBUG_KERNEL
-	depends on X86_SMP
+	depends on SMP
 	default n
-	help
+	---help---
 	  Say Y to verify that the per_cpu map being accessed has
 	  been setup.  Adds a fair amount of code to kernel memory
 	  and decreases performance.
@@ -96,7 +96,7 @@ config X86_PTDUMP
 	bool "Export kernel pagetable layout to userspace via debugfs"
 	depends on DEBUG_KERNEL
 	select DEBUG_FS
-	help
+	---help---
 	  Say Y here if you want to show the kernel pagetable layout in a
 	  debugfs file. This information is only useful for kernel developers
 	  who are working in architecture specific areas of the kernel.
@@ -108,7 +108,7 @@ config DEBUG_RODATA
 	bool "Write protect kernel read-only data structures"
 	default y
 	depends on DEBUG_KERNEL
-	help
+	---help---
 	  Mark the kernel read-only data as write-protected in the pagetables,
 	  in order to catch accidental (and incorrect) writes to such const
 	  data. This is recommended so that we can catch kernel bugs sooner.
@@ -117,7 +117,8 @@ config DEBUG_RODATA
 config DEBUG_RODATA_TEST
 	bool "Testcase for the DEBUG_RODATA feature"
 	depends on DEBUG_RODATA
-	help
+	default y
+	---help---
 	  This option enables a testcase for the DEBUG_RODATA
 	  feature as well as for the change_page_attr() infrastructure.
 	  If in doubt, say "N"
@@ -125,7 +126,7 @@ config DEBUG_RODATA_TEST
 config DEBUG_NX_TEST
 	tristate "Testcase for the NX non-executable stack feature"
 	depends on DEBUG_KERNEL && m
-	help
+	---help---
 	  This option enables a testcase for the CPU NX capability
 	  and the software setup of this feature.
 	  If in doubt, say "N"
@@ -133,7 +134,7 @@ config DEBUG_NX_TEST
 config 4KSTACKS
 	bool "Use 4Kb for kernel stacks instead of 8Kb"
 	depends on X86_32
-	help
+	---help---
 	  If you say Y here the kernel will use a 4Kb stacksize for the
 	  kernel stack attached to each process/thread. This facilitates
 	  running more threads on a system and also reduces the pressure
@@ -144,7 +145,7 @@ config DOUBLEFAULT
 	default y
 	bool "Enable doublefault exception handler" if EMBEDDED
 	depends on X86_32
-	help
+	---help---
 	  This option allows trapping of rare doublefault exceptions that
 	  would otherwise cause a system to silently reboot. Disabling this
 	  option saves about 4k and might cause you much additional grey
@@ -154,7 +155,7 @@ config IOMMU_DEBUG
 	bool "Enable IOMMU debugging"
 	depends on GART_IOMMU && DEBUG_KERNEL
 	depends on X86_64
-	help
+	---help---
 	  Force the IOMMU to on even when you have less than 4GB of
 	  memory and add debugging code. On overflow always panic. And
 	  allow to enable IOMMU leak tracing. Can be disabled at boot
@@ -170,7 +171,7 @@ config IOMMU_LEAK
 	bool "IOMMU leak tracing"
 	depends on DEBUG_KERNEL
 	depends on IOMMU_DEBUG
-	help
+	---help---
 	  Add a simple leak tracer to the IOMMU code. This is useful when you
 	  are debugging a buggy device driver that leaks IOMMU mappings.
 
@@ -203,25 +204,25 @@ choice
 
 config IO_DELAY_0X80
 	bool "port 0x80 based port-IO delay [recommended]"
-	help
+	---help---
 	  This is the traditional Linux IO delay used for in/out_p.
 	  It is the most tested hence safest selection here.
 
 config IO_DELAY_0XED
 	bool "port 0xed based port-IO delay"
-	help
+	---help---
 	  Use port 0xed as the IO delay. This frees up port 0x80 which is
 	  often used as a hardware-debug port.
 
 config IO_DELAY_UDELAY
 	bool "udelay based port-IO delay"
-	help
+	---help---
 	  Use udelay(2) as the IO delay method. This provides the delay
 	  while not having any side-effect on the IO port space.
 
 config IO_DELAY_NONE
 	bool "no port-IO delay"
-	help
+	---help---
 	  No port-IO delay. Will break on old boxes that require port-IO
 	  delay for certain operations. Should work on most new machines.
 
@@ -255,18 +256,18 @@ config DEBUG_BOOT_PARAMS
 	bool "Debug boot parameters"
 	depends on DEBUG_KERNEL
 	depends on DEBUG_FS
-	help
+	---help---
 	  This option will cause struct boot_params to be exported via debugfs.
 
 config CPA_DEBUG
 	bool "CPA self-test code"
 	depends on DEBUG_KERNEL
-	help
+	---help---
 	  Do change_page_attr() self-tests every 30 seconds.
 
 config OPTIMIZE_INLINING
 	bool "Allow gcc to uninline functions marked 'inline'"
-	help
+	---help---
 	  This option determines if the kernel forces gcc to inline the functions
 	  developers have marked 'inline'. Doing so takes away freedom from gcc to
 	  do what it thinks is best, which is desirable for the gcc 3.x series of
@@ -279,4 +280,3 @@ config OPTIMIZE_INLINING
 	  If unsure, say N.
 
 endmenu
-

arch/x86/Makefile

@@ -70,14 +70,17 @@ else
         # this works around some issues with generating unwind tables in older gccs
         # newer gccs do it by default
         KBUILD_CFLAGS += -maccumulate-outgoing-args
+endif
 
-        stackp := $(CONFIG_SHELL) $(srctree)/scripts/gcc-x86_64-has-stack-protector.sh
-        stackp-$(CONFIG_CC_STACKPROTECTOR) := $(shell $(stackp) \
-                "$(CC)" -fstack-protector )
-        stackp-$(CONFIG_CC_STACKPROTECTOR_ALL) += $(shell $(stackp) \
-                "$(CC)" -fstack-protector-all )
-
+ifdef CONFIG_CC_STACKPROTECTOR
+	cc_has_sp := $(srctree)/scripts/gcc-x86_$(BITS)-has-stack-protector.sh
+        ifeq ($(shell $(CONFIG_SHELL) $(cc_has_sp) $(CC)),y)
+                stackp-y := -fstack-protector
+                stackp-$(CONFIG_CC_STACKPROTECTOR_ALL) += -fstack-protector-all
                 KBUILD_CFLAGS += $(stackp-y)
+        else
+                $(warning stack protector enabled but no compiler support)
+        endif
 endif
 
 # Stackpointer is addressed different for 32 bit and 64 bit x86
@@ -102,29 +105,6 @@ KBUILD_CFLAGS += -fno-asynchronous-unwind-tables
 # prevent gcc from generating any FP code by mistake
 KBUILD_CFLAGS += $(call cc-option,-mno-sse -mno-mmx -mno-sse2 -mno-3dnow,)
 
-###
-# Sub architecture support
-# fcore-y is linked before mcore-y files.
-
-# Default subarch .c files
-mcore-y  := arch/x86/mach-default/
-
-# Voyager subarch support
-mflags-$(CONFIG_X86_VOYAGER)	:= -Iarch/x86/include/asm/mach-voyager
-mcore-$(CONFIG_X86_VOYAGER)	:= arch/x86/mach-voyager/
-
-# generic subarchitecture
-mflags-$(CONFIG_X86_GENERICARCH):= -Iarch/x86/include/asm/mach-generic
-fcore-$(CONFIG_X86_GENERICARCH)	+= arch/x86/mach-generic/
-mcore-$(CONFIG_X86_GENERICARCH)	:= arch/x86/mach-default/
-
-# default subarch .h files
-mflags-y += -Iarch/x86/include/asm/mach-default
-
-# 64 bit does not support subarch support - clear sub arch variables
-fcore-$(CONFIG_X86_64)  :=
-mcore-$(CONFIG_X86_64)  :=
-
 KBUILD_CFLAGS += $(mflags-y)
 KBUILD_AFLAGS += $(mflags-y)
 
@@ -150,9 +130,6 @@ core-$(CONFIG_LGUEST_GUEST) += arch/x86/lguest/
 core-y += arch/x86/kernel/
 core-y += arch/x86/mm/
 
-# Remaining sub architecture files
-core-y += $(mcore-y)
-
 core-y += arch/x86/crypto/
 core-y += arch/x86/vdso/
 core-$(CONFIG_IA32_EMULATION) += arch/x86/ia32/

arch/x86/boot/Makefile

@@ -32,7 +32,6 @@ setup-y		+= a20.o cmdline.o copy.o cpu.o cpucheck.o edd.o
 setup-y		+= header.o main.o mca.o memory.o pm.o pmjump.o
 setup-y		+= printf.o string.o tty.o video.o video-mode.o version.o
 setup-$(CONFIG_X86_APM_BOOT) += apm.o
-setup-$(CONFIG_X86_VOYAGER) += voyager.o
 
 # The link order of the video-*.o modules can matter.  In particular,
 # video-vga.o *must* be listed first, followed by video-vesa.o.

arch/x86/boot/a20.c

@@ -2,6 +2,7 @@
  *
  *   Copyright (C) 1991, 1992 Linus Torvalds
  *   Copyright 2007-2008 rPath, Inc. - All Rights Reserved
+ *   Copyright 2009 Intel Corporation
  *
  *   This file is part of the Linux kernel, and is made available under
  *   the terms of the GNU General Public License version 2.
@@ -15,16 +16,23 @@
 #include "boot.h"
 
 #define MAX_8042_LOOPS	100000
+#define MAX_8042_FF	32
 
 static int empty_8042(void)
 {
 	u8 status;
 	int loops = MAX_8042_LOOPS;
+	int ffs   = MAX_8042_FF;
 
 	while (loops--) {
 		io_delay();
 
 		status = inb(0x64);
+		if (status == 0xff) {
+			/* FF is a plausible, but very unlikely status */
+			if (!--ffs)
+				return -1; /* Assume no KBC present */
+		}
 		if (status & 1) {
 			/* Read and discard input data */
 			io_delay();
@@ -118,18 +126,9 @@ static void enable_a20_fast(void)
 
 int enable_a20(void)
 {
-#if defined(CONFIG_X86_ELAN)
-	/* Elan croaks if we try to touch the KBC */
-	enable_a20_fast();
-	while (!a20_test_long())
-		;
-	return 0;
-#elif defined(CONFIG_X86_VOYAGER)
-	/* On Voyager, a20_test() is unsafe? */
-	enable_a20_kbc();
-	return 0;
-#else
        int loops = A20_ENABLE_LOOPS;
+       int kbc_err;
+
        while (loops--) {
 	       /* First, check to see if A20 is already enabled
 		  (legacy free, etc.) */
@@ -142,13 +141,16 @@ int enable_a20(void)
 		       return 0;
 	       
 	       /* Try enabling A20 through the keyboard controller */
-		empty_8042();
+	       kbc_err = empty_8042();
+
 	       if (a20_test_short())
 		       return 0; /* BIOS worked, but with delayed reaction */
 	
+	       if (!kbc_err) {
 		       enable_a20_kbc();
 		       if (a20_test_long())
 			       return 0;
+	       }
 	       
 	       /* Finally, try enabling the "fast A20 gate" */
 	       enable_a20_fast();
@@ -157,5 +159,4 @@ int enable_a20(void)
        }
        
        return -1;
-#endif
 }

arch/x86/boot/boot.h

@@ -302,9 +302,6 @@ void probe_cards(int unsafe);
 /* video-vesa.c */
 void vesa_store_edid(void);
 
-/* voyager.c */
-int query_voyager(void);
-
 #endif /* __ASSEMBLY__ */
 
 #endif /* BOOT_BOOT_H */

arch/x86/boot/compressed/Makefile

@@ -4,7 +4,7 @@
 # create a compressed vmlinux image from the original vmlinux
 #
 
-targets := vmlinux vmlinux.bin vmlinux.bin.gz head_$(BITS).o misc.o piggy.o
+targets := vmlinux vmlinux.bin vmlinux.bin.gz vmlinux.bin.bz2 vmlinux.bin.lzma head_$(BITS).o misc.o piggy.o
 
 KBUILD_CFLAGS := -m$(BITS) -D__KERNEL__ $(LINUX_INCLUDE) -O2
 KBUILD_CFLAGS += -fno-strict-aliasing -fPIC
@@ -47,18 +47,35 @@ ifeq ($(CONFIG_X86_32),y)
 ifdef CONFIG_RELOCATABLE
 $(obj)/vmlinux.bin.gz: $(obj)/vmlinux.bin.all FORCE
 	$(call if_changed,gzip)
+$(obj)/vmlinux.bin.bz2: $(obj)/vmlinux.bin.all FORCE
+	$(call if_changed,bzip2)
+$(obj)/vmlinux.bin.lzma: $(obj)/vmlinux.bin.all FORCE
+	$(call if_changed,lzma)
 else
 $(obj)/vmlinux.bin.gz: $(obj)/vmlinux.bin FORCE
 	$(call if_changed,gzip)
+$(obj)/vmlinux.bin.bz2: $(obj)/vmlinux.bin FORCE
+	$(call if_changed,bzip2)
+$(obj)/vmlinux.bin.lzma: $(obj)/vmlinux.bin FORCE
+	$(call if_changed,lzma)
 endif
 LDFLAGS_piggy.o := -r --format binary --oformat elf32-i386 -T
 
 else
+
 $(obj)/vmlinux.bin.gz: $(obj)/vmlinux.bin FORCE
 	$(call if_changed,gzip)
+$(obj)/vmlinux.bin.bz2: $(obj)/vmlinux.bin FORCE
+	$(call if_changed,bzip2)
+$(obj)/vmlinux.bin.lzma: $(obj)/vmlinux.bin FORCE
+	$(call if_changed,lzma)
 
 LDFLAGS_piggy.o := -r --format binary --oformat elf64-x86-64 -T
 endif
 
-$(obj)/piggy.o: $(obj)/vmlinux.scr $(obj)/vmlinux.bin.gz FORCE
+suffix_$(CONFIG_KERNEL_GZIP)  = gz
+suffix_$(CONFIG_KERNEL_BZIP2) = bz2
+suffix_$(CONFIG_KERNEL_LZMA)  = lzma
+
+$(obj)/piggy.o: $(obj)/vmlinux.scr $(obj)/vmlinux.bin.$(suffix_y) FORCE
 	$(call if_changed,ld)

arch/x86/boot/compressed/head_32.S

@@ -25,14 +25,12 @@
 
 #include <linux/linkage.h>
 #include <asm/segment.h>
-#include <asm/page.h>
+#include <asm/page_types.h>
 #include <asm/boot.h>
 #include <asm/asm-offsets.h>
 
 .section ".text.head","ax",@progbits
-	.globl startup_32
-
-startup_32:
+ENTRY(startup_32)
 	cld
 	/* test KEEP_SEGMENTS flag to see if the bootloader is asking
 	 * us to not reload segments */
@@ -113,6 +111,8 @@ startup_32:
  */
 	leal relocated(%ebx), %eax
 	jmp *%eax
+ENDPROC(startup_32)
+
 .section ".text"
 relocated:
 

arch/x86/boot/compressed/head_64.S

@@ -26,8 +26,8 @@
 
 #include <linux/linkage.h>
 #include <asm/segment.h>
-#include <asm/pgtable.h>
-#include <asm/page.h>
+#include <asm/pgtable_types.h>
+#include <asm/page_types.h>
 #include <asm/boot.h>
 #include <asm/msr.h>
 #include <asm/processor-flags.h>
@@ -35,9 +35,7 @@
 
 .section ".text.head"
 	.code32
-	.globl startup_32
-
-startup_32:
+ENTRY(startup_32)
 	cld
 	/* test KEEP_SEGMENTS flag to see if the bootloader is asking
 	 * us to not reload segments */
@@ -176,6 +174,7 @@ startup_32:
 
 	/* Jump from 32bit compatibility mode into 64bit mode. */
 	lret
+ENDPROC(startup_32)
 
 no_longmode:
 	/* This isn't an x86-64 CPU so hang */
@@ -295,7 +294,6 @@ relocated:
 	call	decompress_kernel
 	popq	%rsi
 
-
 /*
  * Jump to the decompressed kernel.
  */

arch/x86/boot/compressed/misc.c

@@ -116,71 +116,13 @@
 /*
  * gzip declarations
  */
-
-#define OF(args)	args
 #define STATIC		static
 
 #undef memset
 #undef memcpy
 #define memzero(s, n)	memset((s), 0, (n))
 
-typedef unsigned char	uch;
-typedef unsigned short	ush;
-typedef unsigned long	ulg;
-
-/*
- * Window size must be at least 32k, and a power of two.
- * We don't actually have a window just a huge output buffer,
- * so we report a 2G window size, as that should always be
- * larger than our output buffer:
- */
-#define WSIZE		0x80000000
-
-/* Input buffer: */
-static unsigned char	*inbuf;
-
-/* Sliding window buffer (and final output buffer): */
-static unsigned char	*window;
-
-/* Valid bytes in inbuf: */
-static unsigned		insize;
-
-/* Index of next byte to be processed in inbuf: */
-static unsigned		inptr;
-
-/* Bytes in output buffer: */
-static unsigned		outcnt;
-
-/* gzip flag byte */
-#define ASCII_FLAG	0x01 /* bit 0 set: file probably ASCII text */
-#define CONTINUATION	0x02 /* bit 1 set: continuation of multi-part gz file */
-#define EXTRA_FIELD	0x04 /* bit 2 set: extra field present */
-#define ORIG_NAM	0x08 /* bit 3 set: original file name present */
-#define COMMENT		0x10 /* bit 4 set: file comment present */
-#define ENCRYPTED	0x20 /* bit 5 set: file is encrypted */
-#define RESERVED	0xC0 /* bit 6, 7:  reserved */
-
-#define get_byte()	(inptr < insize ? inbuf[inptr++] : fill_inbuf())
-
-/* Diagnostic functions */
-#ifdef DEBUG
-#  define Assert(cond, msg) do { if (!(cond)) error(msg); } while (0)
-#  define Trace(x)	do { fprintf x; } while (0)
-#  define Tracev(x)	do { if (verbose) fprintf x ; } while (0)
-#  define Tracevv(x)	do { if (verbose > 1) fprintf x ; } while (0)
-#  define Tracec(c, x)	do { if (verbose && (c)) fprintf x ; } while (0)
-#  define Tracecv(c, x)	do { if (verbose > 1 && (c)) fprintf x ; } while (0)
-#else
-#  define Assert(cond, msg)
-#  define Trace(x)
-#  define Tracev(x)
-#  define Tracevv(x)
-#  define Tracec(c, x)
-#  define Tracecv(c, x)
-#endif
 
-static int  fill_inbuf(void);
-static void flush_window(void);
 static void error(char *m);
 
 /*
@@ -189,13 +131,8 @@ static void error(char *m);
 static struct boot_params *real_mode;		/* Pointer to real-mode data */
 static int quiet;
 
-extern unsigned char input_data[];
-extern int input_len;
-
-static long bytes_out;
-
 static void *memset(void *s, int c, unsigned n);
-static void *memcpy(void *dest, const void *src, unsigned n);
+void *memcpy(void *dest, const void *src, unsigned n);
 
 static void __putstr(int, const char *);
 #define putstr(__x)  __putstr(0, __x)
@@ -213,7 +150,17 @@ static char *vidmem;
 static int vidport;
 static int lines, cols;
 
-#include "../../../../lib/inflate.c"
+#ifdef CONFIG_KERNEL_GZIP
+#include "../../../../lib/decompress_inflate.c"
+#endif
+
+#ifdef CONFIG_KERNEL_BZIP2
+#include "../../../../lib/decompress_bunzip2.c"
+#endif
+
+#ifdef CONFIG_KERNEL_LZMA
+#include "../../../../lib/decompress_unlzma.c"
+#endif
 
 static void scroll(void)
 {
@@ -282,7 +229,7 @@ static void *memset(void *s, int c, unsigned n)
 	return s;
 }
 
-static void *memcpy(void *dest, const void *src, unsigned n)
+void *memcpy(void *dest, const void *src, unsigned n)
 {
 	int i;
 	const char *s = src;
@@ -293,38 +240,6 @@ static void *memcpy(void *dest, const void *src, unsigned n)
 	return dest;
 }
 
-/* ===========================================================================
- * Fill the input buffer. This is called only when the buffer is empty
- * and at least one byte is really needed.
- */
-static int fill_inbuf(void)
-{
-	error("ran out of input data");
-	return 0;
-}
-
-/* ===========================================================================
- * Write the output window window[0..outcnt-1] and update crc and bytes_out.
- * (Used for the decompressed data only.)
- */
-static void flush_window(void)
-{
-	/* With my window equal to my output buffer
-	 * I only need to compute the crc here.
-	 */
-	unsigned long c = crc;         /* temporary variable */
-	unsigned n;
-	unsigned char *in, ch;
-
-	in = window;
-	for (n = 0; n < outcnt; n++) {
-		ch = *in++;
-		c = crc_32_tab[((int)c ^ ch) & 0xff] ^ (c >> 8);
-	}
-	crc = c;
-	bytes_out += (unsigned long)outcnt;
-	outcnt = 0;
-}
 
 static void error(char *x)
 {
@@ -407,12 +322,8 @@ asmlinkage void decompress_kernel(void *rmode, memptr heap,
 	lines = real_mode->screen_info.orig_video_lines;
 	cols = real_mode->screen_info.orig_video_cols;
 
-	window = output;		/* Output buffer (Normally at 1M) */
 	free_mem_ptr     = heap;	/* Heap */
 	free_mem_end_ptr = heap + BOOT_HEAP_SIZE;
-	inbuf  = input_data;		/* Input buffer */
-	insize = input_len;
-	inptr  = 0;
 
 #ifdef CONFIG_X86_64
 	if ((unsigned long)output & (__KERNEL_ALIGN - 1))
@@ -430,10 +341,9 @@ asmlinkage void decompress_kernel(void *rmode, memptr heap,
 #endif
 #endif
 
-	makecrc();
 	if (!quiet)
 		putstr("\nDecompressing Linux... ");
-	gunzip();
+	decompress(input_data, input_len, NULL, NULL, output, NULL, error);
 	parse_elf(output);
 	if (!quiet)
 		putstr("done.\nBooting the kernel.\n");

arch/x86/boot/copy.S

@@ -8,6 +8,8 @@
  *
  * ----------------------------------------------------------------------- */
 
+#include <linux/linkage.h>
+
 /*
  * Memory copy routines
  */
@@ -15,9 +17,7 @@
 	.code16gcc
 	.text
 
-	.globl	memcpy
-	.type	memcpy, @function
-memcpy:
+GLOBAL(memcpy)
 	pushw	%si
 	pushw	%di
 	movw	%ax, %di
@@ -31,11 +31,9 @@ memcpy:
 	popw	%di
 	popw	%si
 	ret
-	.size	memcpy, .-memcpy
+ENDPROC(memcpy)
 
-	.globl	memset
-	.type	memset, @function
-memset:
+GLOBAL(memset)
 	pushw	%di
 	movw	%ax, %di
 	movzbl	%dl, %eax
@@ -48,52 +46,42 @@ memset:
 	rep; stosb
 	popw	%di
 	ret
-	.size	memset, .-memset
+ENDPROC(memset)
 
-	.globl	copy_from_fs
-	.type	copy_from_fs, @function
-copy_from_fs:
+GLOBAL(copy_from_fs)
 	pushw	%ds
 	pushw	%fs
 	popw	%ds
 	call	memcpy
 	popw	%ds
 	ret
-	.size	copy_from_fs, .-copy_from_fs
+ENDPROC(copy_from_fs)
 
-	.globl	copy_to_fs
-	.type	copy_to_fs, @function
-copy_to_fs:
+GLOBAL(copy_to_fs)
 	pushw	%es
 	pushw	%fs
 	popw	%es
 	call	memcpy
 	popw	%es
 	ret
-	.size	copy_to_fs, .-copy_to_fs
+ENDPROC(copy_to_fs)
 
 #if 0 /* Not currently used, but can be enabled as needed */
-
-	.globl	copy_from_gs
-	.type	copy_from_gs, @function
-copy_from_gs:
+GLOBAL(copy_from_gs)
 	pushw	%ds
 	pushw	%gs
 	popw	%ds
 	call	memcpy
 	popw	%ds
 	ret
-	.size	copy_from_gs, .-copy_from_gs
-	.globl	copy_to_gs
+ENDPROC(copy_from_gs)
 
-	.type	copy_to_gs, @function
-copy_to_gs:
+GLOBAL(copy_to_gs)
 	pushw	%es
 	pushw	%gs
 	popw	%es
 	call	memcpy
 	popw	%es
 	ret
-	.size	copy_to_gs, .-copy_to_gs
-
+ENDPROC(copy_to_gs)
 #endif

arch/x86/boot/header.S

@@ -19,7 +19,7 @@
 #include <linux/utsrelease.h>
 #include <asm/boot.h>
 #include <asm/e820.h>
-#include <asm/page.h>
+#include <asm/page_types.h>
 #include <asm/setup.h>
 #include "boot.h"
 #include "offsets.h"

arch/x86/boot/main.c

@@ -149,11 +149,6 @@ void main(void)
 	/* Query MCA information */
 	query_mca();
 
-	/* Voyager */
-#ifdef CONFIG_X86_VOYAGER
-	query_voyager();
-#endif
-
 	/* Query Intel SpeedStep (IST) information */
 	query_ist();
 

arch/x86/boot/pmjump.S

@@ -15,18 +15,15 @@
 #include <asm/boot.h>
 #include <asm/processor-flags.h>
 #include <asm/segment.h>
+#include <linux/linkage.h>
 
 	.text
-
-	.globl	protected_mode_jump
-	.type	protected_mode_jump, @function
-
 	.code16
 
 /*
  * void protected_mode_jump(u32 entrypoint, u32 bootparams);
  */
-protected_mode_jump:
+GLOBAL(protected_mode_jump)
 	movl	%edx, %esi		# Pointer to boot_params table
 
 	xorl	%ebx, %ebx
@@ -47,12 +44,10 @@ protected_mode_jump:
 	.byte	0x66, 0xea		# ljmpl opcode
 2:	.long	in_pm32			# offset
 	.word	__BOOT_CS		# segment
-
-	.size	protected_mode_jump, .-protected_mode_jump
+ENDPROC(protected_mode_jump)
 
 	.code32
-	.type	in_pm32, @function
-in_pm32:
+GLOBAL(in_pm32)
 	# Set up data segments for flat 32-bit mode
 	movl	%ecx, %ds
 	movl	%ecx, %es
@@ -78,5 +73,4 @@ in_pm32:
 	lldt	%cx
 
 	jmpl	*%eax			# Jump to the 32-bit entrypoint
-
-	.size	in_pm32, .-in_pm32
+ENDPROC(in_pm32)

arch/x86/boot/voyager.c

-/* -*- linux-c -*- ------------------------------------------------------- *
- *
- *   Copyright (C) 1991, 1992 Linus Torvalds
- *   Copyright 2007 rPath, Inc. - All Rights Reserved
- *
- *   This file is part of the Linux kernel, and is made available under
- *   the terms of the GNU General Public License version 2.
- *
- * ----------------------------------------------------------------------- */
-
-/*
- * Get the Voyager config information
- */
-
-#include "boot.h"
-
-int query_voyager(void)
-{
-	u8 err;
-	u16 es, di;
-	/* Abuse the apm_bios_info area for this */
-	u8 *data_ptr = (u8 *)&boot_params.apm_bios_info;
-
-	data_ptr[0] = 0xff;	/* Flag on config not found(?) */
-
-	asm("pushw %%es ; "
-	    "int $0x15 ; "
-	    "setc %0 ; "
-	    "movw %%es, %1 ; "
-	    "popw %%es"
-	    : "=q" (err), "=r" (es), "=D" (di)
-	    : "a" (0xffc0));
-
-	if (err)
-		return -1;	/* Not Voyager */
-
-	set_fs(es);
-	copy_from_fs(data_ptr, di, 7);	/* Table is 7 bytes apparently */
-	return 0;
-}

arch/x86/ia32/ia32entry.S

@@ -112,8 +112,8 @@ ENTRY(ia32_sysenter_target)
 	CFI_DEF_CFA	rsp,0
 	CFI_REGISTER	rsp,rbp
 	SWAPGS_UNSAFE_STACK
-	movq	%gs:pda_kernelstack, %rsp
-	addq	$(PDA_STACKOFFSET),%rsp	
+	movq	PER_CPU_VAR(kernel_stack), %rsp
+	addq	$(KERNEL_STACK_OFFSET),%rsp
 	/*
 	 * No need to follow this irqs on/off section: the syscall
 	 * disabled irqs, here we enable it straight after entry:
@@ -273,13 +273,13 @@ ENDPROC(ia32_sysenter_target)
 ENTRY(ia32_cstar_target)
 	CFI_STARTPROC32	simple
 	CFI_SIGNAL_FRAME
-	CFI_DEF_CFA	rsp,PDA_STACKOFFSET
+	CFI_DEF_CFA	rsp,KERNEL_STACK_OFFSET
 	CFI_REGISTER	rip,rcx
 	/*CFI_REGISTER	rflags,r11*/
 	SWAPGS_UNSAFE_STACK
 	movl	%esp,%r8d
 	CFI_REGISTER	rsp,r8
-	movq	%gs:pda_kernelstack,%rsp
+	movq	PER_CPU_VAR(kernel_stack),%rsp
 	/*
 	 * No need to follow this irqs on/off section: the syscall
 	 * disabled irqs and here we enable it straight after entry:

arch/x86/include/asm/a.out-core.h

@@ -55,7 +55,7 @@ static inline void aout_dump_thread(struct pt_regs *regs, struct user *dump)
 	dump->regs.ds = (u16)regs->ds;
 	dump->regs.es = (u16)regs->es;
 	dump->regs.fs = (u16)regs->fs;
-	savesegment(gs, dump->regs.gs);
+	dump->regs.gs = get_user_gs(regs);
 	dump->regs.orig_ax = regs->orig_ax;
 	dump->regs.ip = regs->ip;
 	dump->regs.cs = (u16)regs->cs;

arch/x86/include/asm/acpi.h

@@ -102,9 +102,6 @@ static inline void disable_acpi(void)
 	acpi_noirq = 1;
 }
 
-/* Fixmap pages to reserve for ACPI boot-time tables (see fixmap.h) */
-#define FIX_ACPI_PAGES 4
-
 extern int acpi_gsi_to_irq(u32 gsi, unsigned int *irq);
 
 static inline void acpi_noirq_set(void) { acpi_noirq = 1; }

arch/x86/include/asm/apicdef.h

@@ -53,6 +53,7 @@
 #define		APIC_ESR_SENDILL	0x00020
 #define		APIC_ESR_RECVILL	0x00040
 #define		APIC_ESR_ILLREGA	0x00080
+#define 	APIC_LVTCMCI	0x2f0
 #define	APIC_ICR	0x300
 #define		APIC_DEST_SELF		0x40000
 #define		APIC_DEST_ALLINC	0x80000

arch/x86/include/asm/apicnum.h

+#ifndef _ASM_X86_APICNUM_H
+#define _ASM_X86_APICNUM_H
+
+/* define MAX_IO_APICS */
+#ifdef CONFIG_X86_32
+# define MAX_IO_APICS 64
+#else
+# define MAX_IO_APICS 128
+# define MAX_LOCAL_APIC 32768
+#endif
+
+#endif /* _ASM_X86_APICNUM_H */

arch/x86/include/asm/arch_hooks.h

-#ifndef _ASM_X86_ARCH_HOOKS_H
-#define _ASM_X86_ARCH_HOOKS_H
-
-#include <linux/interrupt.h>
-
-/*
- *	linux/include/asm/arch_hooks.h
- *
- *	define the architecture specific hooks
- */
-
-/* these aren't arch hooks, they are generic routines
- * that can be used by the hooks */
-extern void init_ISA_irqs(void);
-extern irqreturn_t timer_interrupt(int irq, void *dev_id);
-
-/* these are the defined hooks */
-extern void intr_init_hook(void);
-extern void pre_intr_init_hook(void);
-extern void pre_setup_arch_hook(void);
-extern void trap_init_hook(void);
-extern void pre_time_init_hook(void);
-extern void time_init_hook(void);
-extern void mca_nmi_hook(void);
-
-#endif /* _ASM_X86_ARCH_HOOKS_H */

arch/x86/include/asm/bigsmp/apic.h

-#ifndef __ASM_MACH_APIC_H
-#define __ASM_MACH_APIC_H
-
-#define xapic_phys_to_log_apicid(cpu) (per_cpu(x86_bios_cpu_apicid, cpu))
-#define esr_disable (1)
-
-static inline int apic_id_registered(void)
-{
-	return (1);
-}
-
-static inline const cpumask_t *target_cpus(void)
-{
-#ifdef CONFIG_SMP
-	return &cpu_online_map;
-#else
-	return &cpumask_of_cpu(0);
-#endif
-}
-
-#undef APIC_DEST_LOGICAL
-#define APIC_DEST_LOGICAL	0
-#define APIC_DFR_VALUE		(APIC_DFR_FLAT)
-#define INT_DELIVERY_MODE	(dest_Fixed)
-#define INT_DEST_MODE		(0)    /* phys delivery to target proc */
-#define NO_BALANCE_IRQ		(0)
-
-static inline unsigned long check_apicid_used(physid_mask_t bitmap, int apicid)
-{
-	return (0);
-}
-
-static inline unsigned long check_apicid_present(int bit)
-{
-	return (1);
-}
-
-static inline unsigned long calculate_ldr(int cpu)
-{
-	unsigned long val, id;
-	val = apic_read(APIC_LDR) & ~APIC_LDR_MASK;
-	id = xapic_phys_to_log_apicid(cpu);
-	val |= SET_APIC_LOGICAL_ID(id);
-	return val;
-}
-
-/*
- * Set up the logical destination ID.
- *
- * Intel recommends to set DFR, LDR and TPR before enabling
- * an APIC.  See e.g. "AP-388 82489DX User's Manual" (Intel
- * document number 292116).  So here it goes...
- */
-static inline void init_apic_ldr(void)
-{
-	unsigned long val;
-	int cpu = smp_processor_id();
-
-	apic_write(APIC_DFR, APIC_DFR_VALUE);
-	val = calculate_ldr(cpu);
-	apic_write(APIC_LDR, val);
-}
-
-static inline void setup_apic_routing(void)
-{
-	printk("Enabling APIC mode:  %s.  Using %d I/O APICs\n",
-		"Physflat", nr_ioapics);
-}
-
-static inline int multi_timer_check(int apic, int irq)
-{
-	return (0);
-}
-
-static inline int apicid_to_node(int logical_apicid)
-{
-	return apicid_2_node[hard_smp_processor_id()];
-}
-
-static inline int cpu_present_to_apicid(int mps_cpu)
-{
-	if (mps_cpu < nr_cpu_ids)
-		return (int) per_cpu(x86_bios_cpu_apicid, mps_cpu);
-
-	return BAD_APICID;
-}
-
-static inline physid_mask_t apicid_to_cpu_present(int phys_apicid)
-{
-	return physid_mask_of_physid(phys_apicid);
-}
-
-extern u8 cpu_2_logical_apicid[];
-/* Mapping from cpu number to logical apicid */
-static inline int cpu_to_logical_apicid(int cpu)
-{
-	if (cpu >= nr_cpu_ids)
-		return BAD_APICID;
-	return cpu_physical_id(cpu);
-}
-
-static inline physid_mask_t ioapic_phys_id_map(physid_mask_t phys_map)
-{
-	/* For clustered we don't have a good way to do this yet - hack */
-	return physids_promote(0xFFL);
-}
-
-static inline void setup_portio_remap(void)
-{
-}
-
-static inline void enable_apic_mode(void)
-{
-}
-
-static inline int check_phys_apicid_present(int boot_cpu_physical_apicid)
-{
-	return (1);
-}
-
-/* As we are using single CPU as destination, pick only one CPU here */
-static inline unsigned int cpu_mask_to_apicid(const cpumask_t *cpumask)
-{
-	int cpu;
-	int apicid;	
-
-	cpu = first_cpu(*cpumask);
-	apicid = cpu_to_logical_apicid(cpu);
-	return apicid;
-}
-
-static inline unsigned int cpu_mask_to_apicid_and(const struct cpumask *cpumask,
-						  const struct cpumask *andmask)
-{
-	int cpu;
-
-	/*
-	 * We're using fixed IRQ delivery, can only return one phys APIC ID.
-	 * May as well be the first.
-	 */
-	for_each_cpu_and(cpu, cpumask, andmask)
-		if (cpumask_test_cpu(cpu, cpu_online_mask))
-			break;
-	if (cpu < nr_cpu_ids)
-		return cpu_to_logical_apicid(cpu);
-
-	return BAD_APICID;
-}
-
-static inline u32 phys_pkg_id(u32 cpuid_apic, int index_msb)
-{
-	return cpuid_apic >> index_msb;
-}
-
-#endif /* __ASM_MACH_APIC_H */

arch/x86/include/asm/bigsmp/apicdef.h

-#ifndef __ASM_MACH_APICDEF_H
-#define __ASM_MACH_APICDEF_H
-
-#define		APIC_ID_MASK		(0xFF<<24)
-
-static inline unsigned get_apic_id(unsigned long x)
-{
-	return (((x)>>24)&0xFF);
-}
-
-#define		GET_APIC_ID(x)	get_apic_id(x)
-
-#endif

arch/x86/include/asm/bigsmp/ipi.h

-#ifndef __ASM_MACH_IPI_H
-#define __ASM_MACH_IPI_H
-
-void send_IPI_mask_sequence(const struct cpumask *mask, int vector);
-void send_IPI_mask_allbutself(const struct cpumask *mask, int vector);
-
-static inline void send_IPI_mask(const struct cpumask *mask, int vector)
-{
-	send_IPI_mask_sequence(mask, vector);
-}
-
-static inline void send_IPI_allbutself(int vector)
-{
-	send_IPI_mask_allbutself(cpu_online_mask, vector);
-}
-
-static inline void send_IPI_all(int vector)
-{
-	send_IPI_mask(cpu_online_mask, vector);
-}
-
-#endif /* __ASM_MACH_IPI_H */

arch/x86/include/asm/boot.h

@@ -10,17 +10,31 @@
 #define EXTENDED_VGA	0xfffe		/* 80x50 mode */
 #define ASK_VGA		0xfffd		/* ask for it at bootup */
 
+#ifdef __KERNEL__
+
 /* Physical address where kernel should be loaded. */
 #define LOAD_PHYSICAL_ADDR ((CONFIG_PHYSICAL_START \
 				+ (CONFIG_PHYSICAL_ALIGN - 1)) \
 				& ~(CONFIG_PHYSICAL_ALIGN - 1))
 
+#ifdef CONFIG_KERNEL_BZIP2
+#define BOOT_HEAP_SIZE             0x400000
+#else /* !CONFIG_KERNEL_BZIP2 */
+
 #ifdef CONFIG_X86_64
 #define BOOT_HEAP_SIZE	0x7000
-#define BOOT_STACK_SIZE	0x4000
 #else
 #define BOOT_HEAP_SIZE	0x4000
+#endif
+
+#endif /* !CONFIG_KERNEL_BZIP2 */
+
+#ifdef CONFIG_X86_64
+#define BOOT_STACK_SIZE	0x4000
+#else
 #define BOOT_STACK_SIZE	0x1000
 #endif
 
+#endif /* __KERNEL__ */
+
 #endif /* _ASM_X86_BOOT_H */

arch/x86/include/asm/cpu.h

@@ -7,6 +7,20 @@
 #include <linux/nodemask.h>
 #include <linux/percpu.h>
 
+#ifdef CONFIG_SMP
+
+extern void prefill_possible_map(void);
+
+#else /* CONFIG_SMP */
+
+static inline void prefill_possible_map(void) {}
+
+#define cpu_physical_id(cpu)			boot_cpu_physical_apicid
+#define safe_smp_processor_id()			0
+#define stack_smp_processor_id()		0
+
+#endif /* CONFIG_SMP */
+
 struct x86_cpu {
 	struct cpu cpu;
 };
@@ -17,4 +31,7 @@ extern void arch_unregister_cpu(int);
 #endif
 
 DECLARE_PER_CPU(int, cpu_state);
+
+extern unsigned int boot_cpu_id;
+
 #endif /* _ASM_X86_CPU_H */

arch/x86/include/asm/efi.h

@@ -37,8 +37,6 @@ extern unsigned long asmlinkage efi_call_phys(void *, ...);
 
 #else /* !CONFIG_X86_32 */
 
-#define MAX_EFI_IO_PAGES	100
-
 extern u64 efi_call0(void *fp);
 extern u64 efi_call1(void *fp, u64 arg1);
 extern u64 efi_call2(void *fp, u64 arg1, u64 arg2);