Commit f10239ea authored by Milo Kim's avatar Milo Kim Committed by Maxime Ripard

ARM: dts: sun8i: Use the common file in NanoPi NEO SBC

NanoPi common dtsi supports all components of NEO SBC, so just include it.

Cc: James Pettigrew <james@innovum.com.au>
Signed-off-by: default avatarMilo Kim <woogyom.kim@gmail.com>
Signed-off-by: default avatarMaxime Ripard <maxime.ripard@free-electrons.com>
parent 49f01c9e
...@@ -40,86 +40,9 @@ ...@@ -40,86 +40,9 @@
* OTHER DEALINGS IN THE SOFTWARE. * OTHER DEALINGS IN THE SOFTWARE.
*/ */
/dts-v1/; #include "sun8i-h3-nanopi.dtsi"
#include "sun8i-h3.dtsi"
#include "sunxi-common-regulators.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/pinctrl/sun4i-a10.h>
/ { / {
model = "FriendlyARM NanoPi NEO"; model = "FriendlyARM NanoPi NEO";
compatible = "friendlyarm,nanopi-neo", "allwinner,sun8i-h3"; compatible = "friendlyarm,nanopi-neo", "allwinner,sun8i-h3";
aliases {
serial0 = &uart0;
};
chosen {
stdout-path = "serial0:115200n8";
};
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
pinctrl-0 = <&leds_opc>, <&leds_r_opc>;
pwr {
label = "nanopi:green:pwr";
gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */
default-state = "on";
};
status {
label = "nanopi:blue:status";
gpios = <&pio 0 10 GPIO_ACTIVE_HIGH>; /* PA10 */
};
};
};
&ehci3 {
status = "okay";
};
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
vmmc-supply = <&reg_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
cd-inverted;
status = "okay";
};
&ohci3 {
status = "okay";
};
&pio {
leds_opc: led-pins {
allwinner,pins = "PA10";
allwinner,function = "gpio_out";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
};
&r_pio {
leds_r_opc: led-pins {
allwinner,pins = "PL10";
allwinner,function = "gpio_out";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
};
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
status = "okay";
};
&usbphy {
/* USB VBUS is always on */
status = "okay";
}; };
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment