Commit f38b0dd6 authored by Tero Kristo's avatar Tero Kristo Committed by Mike Turquette

CLK: TI: Add DPLL clock support

The OMAP clock driver now supports DPLL clock type. This patch also
adds support for DT DPLL nodes.
Signed-off-by: default avatarTero Kristo <t-kristo@ti.com>
Acked-by: default avatarTony Lindgren <tony@atomide.com>
Signed-off-by: default avatarMike Turquette <mturquette@linaro.org>
parent 819b4861
Binding for Texas Instruments DPLL clock.
Binding status: Unstable - ABI compatibility may be broken in the future
This binding uses the common clock binding[1]. It assumes a
register-mapped DPLL with usually two selectable input clocks
(reference clock and bypass clock), with digital phase locked
loop logic for multiplying the input clock to a desired output
clock. This clock also typically supports different operation
modes (locked, low power stop etc.) This binding has several
sub-types, which effectively result in slightly different setup
for the actual DPLL clock.
[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
Required properties:
- compatible : shall be one of:
"ti,omap3-dpll-clock",
"ti,omap3-dpll-core-clock",
"ti,omap3-dpll-per-clock",
"ti,omap3-dpll-per-j-type-clock",
"ti,omap4-dpll-clock",
"ti,omap4-dpll-x2-clock",
"ti,omap4-dpll-core-clock",
"ti,omap4-dpll-m4xen-clock",
"ti,omap4-dpll-j-type-clock",
"ti,am3-dpll-no-gate-clock",
"ti,am3-dpll-j-type-clock",
"ti,am3-dpll-no-gate-j-type-clock",
"ti,am3-dpll-clock",
"ti,am3-dpll-core-clock",
"ti,am3-dpll-x2-clock",
- #clock-cells : from common clock binding; shall be set to 0.
- clocks : link phandles of parent clocks, first entry lists reference clock
and second entry bypass clock
- reg : offsets for the register set for controlling the DPLL.
Registers are listed in following order:
"control" - contains the control register base address
"idlest" - contains the idle status register base address
"mult-div1" - contains the multiplier / divider register base address
"autoidle" - contains the autoidle register base address (optional)
ti,am3-* dpll types do not have autoidle register
Optional properties:
- DPLL mode setting - defining any one or more of the following overrides
default setting.
- ti,low-power-stop : DPLL supports low power stop mode, gating output
- ti,low-power-bypass : DPLL output matches rate of parent bypass clock
- ti,lock : DPLL locks in programmed rate
Examples:
dpll_core_ck: dpll_core_ck@44e00490 {
#clock-cells = <0>;
compatible = "ti,omap4-dpll-core-clock";
clocks = <&sys_clkin_ck>, <&sys_clkin_ck>;
reg = <0x490>, <0x45c>, <0x488>, <0x468>;
};
dpll2_ck: dpll2_ck@48004004 {
#clock-cells = <0>;
compatible = "ti,omap3-dpll-clock";
clocks = <&sys_ck>, <&dpll2_fck>;
ti,low-power-stop;
ti,low-power-bypass;
ti,lock;
reg = <0x4>, <0x24>, <0x34>, <0x40>;
};
dpll_core_ck: dpll_core_ck@44e00490 {
#clock-cells = <0>;
compatible = "ti,am3-dpll-core-clock";
clocks = <&sys_clkin_ck>, <&sys_clkin_ck>;
reg = <0x90>, <0x5c>, <0x68>;
};
...@@ -21,6 +21,7 @@ ...@@ -21,6 +21,7 @@
#include <linux/clkdev.h> #include <linux/clkdev.h>
#include <linux/clk-provider.h> #include <linux/clk-provider.h>
#include <linux/clk/ti.h>
struct omap_clk { struct omap_clk {
u16 cpu; u16 cpu;
...@@ -37,7 +38,6 @@ struct omap_clk { ...@@ -37,7 +38,6 @@ struct omap_clk {
} }
struct clockdomain; struct clockdomain;
#define to_clk_hw_omap(_hw) container_of(_hw, struct clk_hw_omap, hw)
#define DEFINE_STRUCT_CLK(_name, _parent_array_name, _clkops_name) \ #define DEFINE_STRUCT_CLK(_name, _parent_array_name, _clkops_name) \
static struct clk _name = { \ static struct clk _name = { \
...@@ -178,141 +178,6 @@ struct clksel { ...@@ -178,141 +178,6 @@ struct clksel {
const struct clksel_rate *rates; const struct clksel_rate *rates;
}; };
/**
* struct dpll_data - DPLL registers and integration data
* @mult_div1_reg: register containing the DPLL M and N bitfields
* @mult_mask: mask of the DPLL M bitfield in @mult_div1_reg
* @div1_mask: mask of the DPLL N bitfield in @mult_div1_reg
* @clk_bypass: struct clk pointer to the clock's bypass clock input
* @clk_ref: struct clk pointer to the clock's reference clock input
* @control_reg: register containing the DPLL mode bitfield
* @enable_mask: mask of the DPLL mode bitfield in @control_reg
* @last_rounded_rate: cache of the last rate result of omap2_dpll_round_rate()
* @last_rounded_m: cache of the last M result of omap2_dpll_round_rate()
* @last_rounded_m4xen: cache of the last M4X result of
* omap4_dpll_regm4xen_round_rate()
* @last_rounded_lpmode: cache of the last lpmode result of
* omap4_dpll_lpmode_recalc()
* @max_multiplier: maximum valid non-bypass multiplier value (actual)
* @last_rounded_n: cache of the last N result of omap2_dpll_round_rate()
* @min_divider: minimum valid non-bypass divider value (actual)
* @max_divider: maximum valid non-bypass divider value (actual)
* @modes: possible values of @enable_mask
* @autoidle_reg: register containing the DPLL autoidle mode bitfield
* @idlest_reg: register containing the DPLL idle status bitfield
* @autoidle_mask: mask of the DPLL autoidle mode bitfield in @autoidle_reg
* @freqsel_mask: mask of the DPLL jitter correction bitfield in @control_reg
* @idlest_mask: mask of the DPLL idle status bitfield in @idlest_reg
* @lpmode_mask: mask of the DPLL low-power mode bitfield in @control_reg
* @m4xen_mask: mask of the DPLL M4X multiplier bitfield in @control_reg
* @auto_recal_bit: bitshift of the driftguard enable bit in @control_reg
* @recal_en_bit: bitshift of the PRM_IRQENABLE_* bit for recalibration IRQs
* @recal_st_bit: bitshift of the PRM_IRQSTATUS_* bit for recalibration IRQs
* @flags: DPLL type/features (see below)
*
* Possible values for @flags:
* DPLL_J_TYPE: "J-type DPLL" (only some 36xx, 4xxx DPLLs)
*
* @freqsel_mask is only used on the OMAP34xx family and AM35xx.
*
* XXX Some DPLLs have multiple bypass inputs, so it's not technically
* correct to only have one @clk_bypass pointer.
*
* XXX The runtime-variable fields (@last_rounded_rate, @last_rounded_m,
* @last_rounded_n) should be separated from the runtime-fixed fields
* and placed into a different structure, so that the runtime-fixed data
* can be placed into read-only space.
*/
struct dpll_data {
void __iomem *mult_div1_reg;
u32 mult_mask;
u32 div1_mask;
struct clk *clk_bypass;
struct clk *clk_ref;
void __iomem *control_reg;
u32 enable_mask;
unsigned long last_rounded_rate;
u16 last_rounded_m;
u8 last_rounded_m4xen;
u8 last_rounded_lpmode;
u16 max_multiplier;
u8 last_rounded_n;
u8 min_divider;
u16 max_divider;
u8 modes;
void __iomem *autoidle_reg;
void __iomem *idlest_reg;
u32 autoidle_mask;
u32 freqsel_mask;
u32 idlest_mask;
u32 dco_mask;
u32 sddiv_mask;
u32 lpmode_mask;
u32 m4xen_mask;
u8 auto_recal_bit;
u8 recal_en_bit;
u8 recal_st_bit;
u8 flags;
};
/*
* struct clk.flags possibilities
*
* XXX document the rest of the clock flags here
*
* CLOCK_CLKOUTX2: (OMAP4 only) DPLL CLKOUT and CLKOUTX2 GATE_CTRL
* bits share the same register. This flag allows the
* omap4_dpllmx*() code to determine which GATE_CTRL bit field
* should be used. This is a temporary solution - a better approach
* would be to associate clock type-specific data with the clock,
* similar to the struct dpll_data approach.
*/
#define ENABLE_REG_32BIT (1 << 0) /* Use 32-bit access */
#define CLOCK_IDLE_CONTROL (1 << 1)
#define CLOCK_NO_IDLE_PARENT (1 << 2)
#define ENABLE_ON_INIT (1 << 3) /* Enable upon framework init */
#define INVERT_ENABLE (1 << 4) /* 0 enables, 1 disables */
#define CLOCK_CLKOUTX2 (1 << 5)
/**
* struct clk_hw_omap - OMAP struct clk
* @node: list_head connecting this clock into the full clock list
* @enable_reg: register to write to enable the clock (see @enable_bit)
* @enable_bit: bitshift to write to enable/disable the clock (see @enable_reg)
* @flags: see "struct clk.flags possibilities" above
* @clksel_reg: for clksel clks, register va containing src/divisor select
* @clksel_mask: bitmask in @clksel_reg for the src/divisor selector
* @clksel: for clksel clks, pointer to struct clksel for this clock
* @dpll_data: for DPLLs, pointer to struct dpll_data for this clock
* @clkdm_name: clockdomain name that this clock is contained in
* @clkdm: pointer to struct clockdomain, resolved from @clkdm_name at runtime
* @rate_offset: bitshift for rate selection bitfield (OMAP1 only)
* @src_offset: bitshift for source selection bitfield (OMAP1 only)
*
* XXX @rate_offset, @src_offset should probably be removed and OMAP1
* clock code converted to use clksel.
*
*/
struct clk_hw_omap_ops;
struct clk_hw_omap {
struct clk_hw hw;
struct list_head node;
unsigned long fixed_rate;
u8 fixed_div;
void __iomem *enable_reg;
u8 enable_bit;
u8 flags;
void __iomem *clksel_reg;
u32 clksel_mask;
const struct clksel *clksel;
struct dpll_data *dpll_data;
const char *clkdm_name;
struct clockdomain *clkdm;
const struct clk_hw_omap_ops *ops;
};
struct clk_hw_omap_ops { struct clk_hw_omap_ops {
void (*find_idlest)(struct clk_hw_omap *oclk, void (*find_idlest)(struct clk_hw_omap *oclk,
void __iomem **idlest_reg, void __iomem **idlest_reg,
...@@ -348,36 +213,13 @@ unsigned long omap_fixed_divisor_recalc(struct clk_hw *hw, ...@@ -348,36 +213,13 @@ unsigned long omap_fixed_divisor_recalc(struct clk_hw *hw,
#define OMAP4XXX_EN_DPLL_FRBYPASS 0x6 #define OMAP4XXX_EN_DPLL_FRBYPASS 0x6
#define OMAP4XXX_EN_DPLL_LOCKED 0x7 #define OMAP4XXX_EN_DPLL_LOCKED 0x7
/* CM_CLKEN_PLL*.EN* bit values - not all are available for every DPLL */
#define DPLL_LOW_POWER_STOP 0x1
#define DPLL_LOW_POWER_BYPASS 0x5
#define DPLL_LOCKED 0x7
/* DPLL Type and DCO Selection Flags */
#define DPLL_J_TYPE 0x1
long omap2_dpll_round_rate(struct clk_hw *hw, unsigned long target_rate,
unsigned long *parent_rate);
unsigned long omap3_dpll_recalc(struct clk_hw *hw, unsigned long parent_rate);
int omap3_noncore_dpll_enable(struct clk_hw *hw);
void omap3_noncore_dpll_disable(struct clk_hw *hw);
int omap3_noncore_dpll_set_rate(struct clk_hw *hw, unsigned long rate,
unsigned long parent_rate);
u32 omap3_dpll_autoidle_read(struct clk_hw_omap *clk); u32 omap3_dpll_autoidle_read(struct clk_hw_omap *clk);
void omap3_dpll_allow_idle(struct clk_hw_omap *clk); void omap3_dpll_allow_idle(struct clk_hw_omap *clk);
void omap3_dpll_deny_idle(struct clk_hw_omap *clk); void omap3_dpll_deny_idle(struct clk_hw_omap *clk);
unsigned long omap3_clkoutx2_recalc(struct clk_hw *hw,
unsigned long parent_rate);
int omap4_dpllmx_gatectrl_read(struct clk_hw_omap *clk); int omap4_dpllmx_gatectrl_read(struct clk_hw_omap *clk);
void omap4_dpllmx_allow_gatectrl(struct clk_hw_omap *clk); void omap4_dpllmx_allow_gatectrl(struct clk_hw_omap *clk);
void omap4_dpllmx_deny_gatectrl(struct clk_hw_omap *clk); void omap4_dpllmx_deny_gatectrl(struct clk_hw_omap *clk);
unsigned long omap4_dpll_regm4xen_recalc(struct clk_hw *hw,
unsigned long parent_rate);
long omap4_dpll_regm4xen_round_rate(struct clk_hw *hw,
unsigned long target_rate,
unsigned long *parent_rate);
void omap2_init_clk_clkdm(struct clk_hw *clk);
void __init omap2_clk_disable_clkdm_control(void); void __init omap2_clk_disable_clkdm_control(void);
/* clkt_clksel.c public functions */ /* clkt_clksel.c public functions */
...@@ -396,7 +238,6 @@ int omap2_clksel_set_parent(struct clk_hw *hw, u8 field_val); ...@@ -396,7 +238,6 @@ int omap2_clksel_set_parent(struct clk_hw *hw, u8 field_val);
extern void omap2_clkt_iclk_allow_idle(struct clk_hw_omap *clk); extern void omap2_clkt_iclk_allow_idle(struct clk_hw_omap *clk);
extern void omap2_clkt_iclk_deny_idle(struct clk_hw_omap *clk); extern void omap2_clkt_iclk_deny_idle(struct clk_hw_omap *clk);
u8 omap2_init_dpll_parent(struct clk_hw *hw);
unsigned long omap2_get_dpll_rate(struct clk_hw_omap *clk); unsigned long omap2_get_dpll_rate(struct clk_hw_omap *clk);
int omap2_dflt_clk_enable(struct clk_hw *hw); int omap2_dflt_clk_enable(struct clk_hw *hw);
...@@ -408,7 +249,6 @@ void omap2_clk_dflt_find_companion(struct clk_hw_omap *clk, ...@@ -408,7 +249,6 @@ void omap2_clk_dflt_find_companion(struct clk_hw_omap *clk,
void omap2_clk_dflt_find_idlest(struct clk_hw_omap *clk, void omap2_clk_dflt_find_idlest(struct clk_hw_omap *clk,
void __iomem **idlest_reg, void __iomem **idlest_reg,
u8 *idlest_bit, u8 *idlest_val); u8 *idlest_bit, u8 *idlest_val);
void omap2_init_clk_hw_omap_clocks(struct clk *clk);
int omap2_clk_enable_autoidle_all(void); int omap2_clk_enable_autoidle_all(void);
int omap2_clk_disable_autoidle_all(void); int omap2_clk_disable_autoidle_all(void);
int omap2_clk_allow_idle(struct clk *clk); int omap2_clk_allow_idle(struct clk *clk);
...@@ -433,10 +273,8 @@ extern const struct clksel_rate gfx_l3_rates[]; ...@@ -433,10 +273,8 @@ extern const struct clksel_rate gfx_l3_rates[];
extern const struct clksel_rate dsp_ick_rates[]; extern const struct clksel_rate dsp_ick_rates[];
extern struct clk dummy_ck; extern struct clk dummy_ck;
extern const struct clk_hw_omap_ops clkhwops_omap3_dpll;
extern const struct clk_hw_omap_ops clkhwops_iclk_wait; extern const struct clk_hw_omap_ops clkhwops_iclk_wait;
extern const struct clk_hw_omap_ops clkhwops_wait; extern const struct clk_hw_omap_ops clkhwops_wait;
extern const struct clk_hw_omap_ops clkhwops_omap4_dpllmx;
extern const struct clk_hw_omap_ops clkhwops_iclk; extern const struct clk_hw_omap_ops clkhwops_iclk;
extern const struct clk_hw_omap_ops clkhwops_omap3430es2_ssi_wait; extern const struct clk_hw_omap_ops clkhwops_omap3430es2_ssi_wait;
extern const struct clk_hw_omap_ops clkhwops_omap3430es2_iclk_ssi_wait; extern const struct clk_hw_omap_ops clkhwops_omap3430es2_iclk_ssi_wait;
......
...@@ -9,8 +9,6 @@ ...@@ -9,8 +9,6 @@
#define __ARCH_ARM_MACH_OMAP2_CLOCK3XXX_H #define __ARCH_ARM_MACH_OMAP2_CLOCK3XXX_H
int omap3xxx_clk_init(void); int omap3xxx_clk_init(void);
int omap3_dpll4_set_rate(struct clk_hw *clk, unsigned long rate,
unsigned long parent_rate);
int omap3_core_dpll_m2_set_rate(struct clk_hw *clk, unsigned long rate, int omap3_core_dpll_m2_set_rate(struct clk_hw *clk, unsigned long rate,
unsigned long parent_rate); unsigned long parent_rate);
void omap3_clk_lock_dpll5(void); void omap3_clk_lock_dpll5(void);
......
ifneq ($(CONFIG_OF),) ifneq ($(CONFIG_OF),)
obj-y += clk.o obj-y += clk.o
clk-common = dpll.o
endif endif
This diff is collapsed.
...@@ -17,6 +17,153 @@ ...@@ -17,6 +17,153 @@
#include <linux/clkdev.h> #include <linux/clkdev.h>
/**
* struct dpll_data - DPLL registers and integration data
* @mult_div1_reg: register containing the DPLL M and N bitfields
* @mult_mask: mask of the DPLL M bitfield in @mult_div1_reg
* @div1_mask: mask of the DPLL N bitfield in @mult_div1_reg
* @clk_bypass: struct clk pointer to the clock's bypass clock input
* @clk_ref: struct clk pointer to the clock's reference clock input
* @control_reg: register containing the DPLL mode bitfield
* @enable_mask: mask of the DPLL mode bitfield in @control_reg
* @last_rounded_rate: cache of the last rate result of omap2_dpll_round_rate()
* @last_rounded_m: cache of the last M result of omap2_dpll_round_rate()
* @last_rounded_m4xen: cache of the last M4X result of
* omap4_dpll_regm4xen_round_rate()
* @last_rounded_lpmode: cache of the last lpmode result of
* omap4_dpll_lpmode_recalc()
* @max_multiplier: maximum valid non-bypass multiplier value (actual)
* @last_rounded_n: cache of the last N result of omap2_dpll_round_rate()
* @min_divider: minimum valid non-bypass divider value (actual)
* @max_divider: maximum valid non-bypass divider value (actual)
* @modes: possible values of @enable_mask
* @autoidle_reg: register containing the DPLL autoidle mode bitfield
* @idlest_reg: register containing the DPLL idle status bitfield
* @autoidle_mask: mask of the DPLL autoidle mode bitfield in @autoidle_reg
* @freqsel_mask: mask of the DPLL jitter correction bitfield in @control_reg
* @idlest_mask: mask of the DPLL idle status bitfield in @idlest_reg
* @lpmode_mask: mask of the DPLL low-power mode bitfield in @control_reg
* @m4xen_mask: mask of the DPLL M4X multiplier bitfield in @control_reg
* @auto_recal_bit: bitshift of the driftguard enable bit in @control_reg
* @recal_en_bit: bitshift of the PRM_IRQENABLE_* bit for recalibration IRQs
* @recal_st_bit: bitshift of the PRM_IRQSTATUS_* bit for recalibration IRQs
* @flags: DPLL type/features (see below)
*
* Possible values for @flags:
* DPLL_J_TYPE: "J-type DPLL" (only some 36xx, 4xxx DPLLs)
*
* @freqsel_mask is only used on the OMAP34xx family and AM35xx.
*
* XXX Some DPLLs have multiple bypass inputs, so it's not technically
* correct to only have one @clk_bypass pointer.
*
* XXX The runtime-variable fields (@last_rounded_rate, @last_rounded_m,
* @last_rounded_n) should be separated from the runtime-fixed fields
* and placed into a different structure, so that the runtime-fixed data
* can be placed into read-only space.
*/
struct dpll_data {
void __iomem *mult_div1_reg;
u32 mult_mask;
u32 div1_mask;
struct clk *clk_bypass;
struct clk *clk_ref;
void __iomem *control_reg;
u32 enable_mask;
unsigned long last_rounded_rate;
u16 last_rounded_m;
u8 last_rounded_m4xen;
u8 last_rounded_lpmode;
u16 max_multiplier;
u8 last_rounded_n;
u8 min_divider;
u16 max_divider;
u8 modes;
void __iomem *autoidle_reg;
void __iomem *idlest_reg;
u32 autoidle_mask;
u32 freqsel_mask;
u32 idlest_mask;
u32 dco_mask;
u32 sddiv_mask;
u32 lpmode_mask;
u32 m4xen_mask;
u8 auto_recal_bit;
u8 recal_en_bit;
u8 recal_st_bit;
u8 flags;
};
struct clk_hw_omap_ops;
/**
* struct clk_hw_omap - OMAP struct clk
* @node: list_head connecting this clock into the full clock list
* @enable_reg: register to write to enable the clock (see @enable_bit)
* @enable_bit: bitshift to write to enable/disable the clock (see @enable_reg)
* @flags: see "struct clk.flags possibilities" above
* @clksel_reg: for clksel clks, register va containing src/divisor select
* @clksel_mask: bitmask in @clksel_reg for the src/divisor selector
* @clksel: for clksel clks, pointer to struct clksel for this clock
* @dpll_data: for DPLLs, pointer to struct dpll_data for this clock
* @clkdm_name: clockdomain name that this clock is contained in
* @clkdm: pointer to struct clockdomain, resolved from @clkdm_name at runtime
* @ops: clock ops for this clock
*/
struct clk_hw_omap {
struct clk_hw hw;
struct list_head node;
unsigned long fixed_rate;
u8 fixed_div;
void __iomem *enable_reg;
u8 enable_bit;
u8 flags;
void __iomem *clksel_reg;
u32 clksel_mask;
const struct clksel *clksel;
struct dpll_data *dpll_data;
const char *clkdm_name;
struct clockdomain *clkdm;
const struct clk_hw_omap_ops *ops;
};
/*
* struct clk_hw_omap.flags possibilities
*
* XXX document the rest of the clock flags here
*
* ENABLE_REG_32BIT: (OMAP1 only) clock control register must be accessed
* with 32bit ops, by default OMAP1 uses 16bit ops.
* CLOCK_IDLE_CONTROL: (OMAP1 only) clock has autoidle support.
* CLOCK_NO_IDLE_PARENT: (OMAP1 only) when clock is enabled, its parent
* clock is put to no-idle mode.
* ENABLE_ON_INIT: Clock is enabled on init.
* INVERT_ENABLE: By default, clock enable bit behavior is '1' enable, '0'
* disable. This inverts the behavior making '0' enable and '1' disable.
* CLOCK_CLKOUTX2: (OMAP4 only) DPLL CLKOUT and CLKOUTX2 GATE_CTRL
* bits share the same register. This flag allows the
* omap4_dpllmx*() code to determine which GATE_CTRL bit field
* should be used. This is a temporary solution - a better approach
* would be to associate clock type-specific data with the clock,
* similar to the struct dpll_data approach.
* MEMMAP_ADDRESSING: Use memmap addressing to access clock registers.
*/
#define ENABLE_REG_32BIT (1 << 0) /* Use 32-bit access */
#define CLOCK_IDLE_CONTROL (1 << 1)
#define CLOCK_NO_IDLE_PARENT (1 << 2)
#define ENABLE_ON_INIT (1 << 3) /* Enable upon framework init */
#define INVERT_ENABLE (1 << 4) /* 0 enables, 1 disables */
#define CLOCK_CLKOUTX2 (1 << 5)
#define MEMMAP_ADDRESSING (1 << 6)
/* CM_CLKEN_PLL*.EN* bit values - not all are available for every DPLL */
#define DPLL_LOW_POWER_STOP 0x1
#define DPLL_LOW_POWER_BYPASS 0x5
#define DPLL_LOCKED 0x7
/* DPLL Type and DCO Selection Flags */
#define DPLL_J_TYPE 0x1
/** /**
* struct ti_dt_clk - OMAP DT clock alias declarations * struct ti_dt_clk - OMAP DT clock alias declarations
* @lk: clock lookup definition * @lk: clock lookup definition
...@@ -68,10 +215,35 @@ struct ti_clk_ll_ops { ...@@ -68,10 +215,35 @@ struct ti_clk_ll_ops {
extern struct ti_clk_ll_ops *ti_clk_ll_ops; extern struct ti_clk_ll_ops *ti_clk_ll_ops;
#define to_clk_hw_omap(_hw) container_of(_hw, struct clk_hw_omap, hw)
void omap2_init_clk_hw_omap_clocks(struct clk *clk);
int omap3_noncore_dpll_enable(struct clk_hw *hw);
void omap3_noncore_dpll_disable(struct clk_hw *hw);
int omap3_noncore_dpll_set_rate(struct clk_hw *hw, unsigned long rate,
unsigned long parent_rate);
unsigned long omap4_dpll_regm4xen_recalc(struct clk_hw *hw,
unsigned long parent_rate);
long omap4_dpll_regm4xen_round_rate(struct clk_hw *hw,
unsigned long target_rate,
unsigned long *parent_rate);
u8 omap2_init_dpll_parent(struct clk_hw *hw);
unsigned long omap3_dpll_recalc(struct clk_hw *hw, unsigned long parent_rate);
long omap2_dpll_round_rate(struct clk_hw *hw, unsigned long target_rate,
unsigned long *parent_rate);
void omap2_init_clk_clkdm(struct clk_hw *clk);
unsigned long omap3_clkoutx2_recalc(struct clk_hw *hw,
unsigned long parent_rate);
int omap3_dpll4_set_rate(struct clk_hw *clk, unsigned long rate,
unsigned long parent_rate);
void __iomem *ti_clk_get_reg_addr(struct device_node *node, int index); void __iomem *ti_clk_get_reg_addr(struct device_node *node, int index);
void ti_dt_clocks_register(struct ti_dt_clk *oclks); void ti_dt_clocks_register(struct ti_dt_clk *oclks);
void ti_dt_clk_init_provider(struct device_node *np, int index); void ti_dt_clk_init_provider(struct device_node *np, int index);
int ti_clk_retry_init(struct device_node *node, struct clk_hw *hw, int ti_clk_retry_init(struct device_node *node, struct clk_hw *hw,
ti_of_clk_init_cb_t func); ti_of_clk_init_cb_t func);
extern const struct clk_hw_omap_ops clkhwops_omap3_dpll;
extern const struct clk_hw_omap_ops clkhwops_omap4_dpllmx;
#endif #endif
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment