This patch added the processing which should be done to hardware,
when a FIFO over run error occurred.
Signed-off-by: Toshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixed the issue which receives an unnecessary packet before link

When using PHY of GMII, an unnecessary packet is received,
And it becomes impossible to receive a packet after link up.
Signed-off-by: Toshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This was originally done as part of commit
65f0b417 ("sfc: Use write-combining to
reduce TX latency"), but that had to be reverted.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commits 65f0b417,
d88d6b05,
fcfa0604,
747df225 and
867955f5.

Depending on the processor model, write-combining may result in
reordering that the NIC will not tolerate.  This typically results
in a DMA error event and reset by the driver, logged as:

sfc 0000:0e:00.0: eth2: TX DMA Q reports TX_EV_PKT_ERR.
sfc 0000:0e:00.0: eth2: resetting (ALL)
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Enable changing advertisement settings via ethtool.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix 1G link LED for the BCM578xx-SFI/KR.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change XMAC loopback type from CORE LOCAL to LINE LOCAL for the BCM578xx due to intermittent problem with the loopback with this configuration.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove remote fault detection as a tactic retreat due to link issues involved with it.
Once issue is resolved, this feature will be restored again.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Enable FEC(Forward Error Correction) for 57810-KR to reduce link errors.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ETS bandwidth of 0% is not allowed by driver, so provide alternative HW configuration for this case.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

d8873315 introduced the IFF_SKB_TX_SHARING flag, which I unilaterally set in
ether_setup.  In doing this I didn't realize that other flags (such as
IFF_XMIT_DST_RELEASE) might be set prior to calling the ether_setup routine.
This patch changes ether_setup to or in SKB_TX_SHARING so as not to
inadvertently clear other existing flags.  Thanks to Pekka Riikonen for pointing
out my error
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reported-by: Pekka Riikonen <priikone@iki.fi>
CC: "David S. Miller" <davem@davemloft.net>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

dev_forward_skb loops an skb back into host networking
stack which might hang on the memory indefinitely.
In particular, this can happen in macvtap in bridged mode.
Copy the userspace fragments to avoid blocking the
sender in that case.

As this patch makes skb_copy_ubufs extern now,
I also added some documentation and made it clear
the SKBTX_DEV_ZEROCOPY flag automatically instead
of doing it in all callers. This can be made into a separate
patch if people feel it's worth it.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

flow_cache_lookup will return a cached object (or null pointer) that the
resolver (i.e. xfrm_policy_lookup) previously found for another namespace
using the same key/family/dir.  Instead, make the namespace part of what
identifies entries in the cache.

As before, flow_entry_valid will return 0 for entries where the namespace
has been deleted, and they will be removed from the cache the next time
flow_cache_gc_task is run.
Reported-by: Andrew Dickinson <whydna@whydna.net>
Signed-off-by: David Ward <david.ward@ll.mit.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add USB product ID for iPhone 4 CDMA Verizon
Tested on at least 2 devices
Signed-off-by: Kavan Smith <kavansmith82@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is important for SMP platform to check if timer function is
executing on other CPU with deleting the timer.

Signed-off-by: Rajan Aggarwal <Rajan Aggarwal rajan.aggarwal85@gmail.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

The dmfe module is a orphan driver, and with this was removed the maintainer
of the documentation.
Signed-off-by: Marcos Paulo de Souza <marcos.mage@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

"Possible SYN flooding on port xxxx " messages can fill logs on servers.

Change logic to log the message only once per listener, and add two new
SNMP counters to track :

TCPReqQFullDoCookies : number of times a SYNCOOKIE was replied to client

TCPReqQFullDrop : number of times a SYN request was dropped because
syncookies were not enabled.

Based on a prior patch from Tom Herbert, and suggestions from David.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

File cls_rsvp.h in /net/sched was outdated. I'm sending you patch for this
file.

[ tb[] array should be indexed by X not X-1 -DaveM ]
Signed-off-by: Igor Maravić <igorm@etf.rs>
Signed-off-by: David S. Miller <davem@davemloft.net>

Seperated Rx and Tx coalescing to different state machines.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Number of VNs for 4-port devices is 2 instead of 4
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Store the size in bp, read from bp when queried.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It may happen every link toggle.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix the thresholds according to 5778x HW and increase rx_ring size
to suit new thresholds in dropless_fc mode.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the command queue is constantly busy,
which can happen in P2P, the hangcheck
timer will frequently find a command in
it and will eventually reset the device
because nothing sets the timestamp for
this queue when commands are processed.

Fix this by setting the timestamp when
a command completes.

Cc: stable@kernel.org #2.6.39, #3.0.0 #3.1.0
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
SIgned-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Alexander reported a strange crash in iwlagn that
Meenakshi and Wey couldn't reproduce. I just ran
into the same issue and tracked it down to stack
corruption. This fixes it.

The problem was introduced in
commit 4b8b99b6e650d0527f3a123744b7459976581d14
Author: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Date:   Fri Jul 8 14:29:48 2011 -0700

    iwlagn: radio sensor offset in le16 format

Cc: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Cc: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Reported-by: Alexander Diewald <alex@diewald.cc>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

when the device is yanked out ath_pci_remove starts doing the cleanups,
unregistering the hardware etc. so we should bail out immediately when
we get drv_flush callback from mac80211 when the card is being unplugged.
the panic occurs after we had associated to an AP.

	EIP: 0060:[<fb315b00>] EFLAGS: 00010246 CPU: 0
	EIP is at ath_reset+0xa0/0x1c0 [ath9k]
	EAX: 00000000 EBX: 000697c0 ECX: 00000002 EDX: f3c3ccf0
	ESI: 00000000 EDI: 00000000 EBP: f43e7b78 ESP: f43e7b50
 	DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
 	Process kworker/u:2 (pid: 182, ti=f43e6000 task=f3c3c7c0
	task.ti=f43e6000)
 	Stack:
 	0000002a 00000000 00000000 003e7b78 0000000f eaaa8500
	ffffffea eaaa97c0
 	eaaaa000 00000001 f43e7ba8 fb315d23 f99e7721 ecece680
	eaaac738 eaaa8500
 	eaaaa020 000000c8 000000c8 00000000 eaaa8d58 eaaa8500
	f43e7bd0 fb080b29
 	Call Trace:
	[<fb315d23>] ath9k_flush+0x103/0x170 [ath9k]
	[<fb080b29>] __ieee80211_recalc_idle+0x2c9/0x400
	[mac80211]
	[<fb080c8e>] ieee80211_recalc_idle+0x2e/0x60 [mac80211]
	[<fb07aa73>] ieee80211_mgd_deauth+0x173/0x210 [mac80211]
	[<fb084559>] ieee80211_deauth+0x19/0x20 [mac80211]
	[<f99dda53>] __cfg80211_mlme_deauth+0xf3/0x140
	[cfg80211]
	[<c0633d00>] ? __mutex_lock_common+0x1f0/0x380
	[<f99e1b5d>] __cfg80211_disconnect+0x18d/0x1f0
	[cfg80211]
	[<f99c8199>] cfg80211_netdev_notifier_call+0x159/0x5c0
	[cfg80211]
	[<c0608a64>] ? packet_notifier+0x174/0x1f0
	[<c0639202>] notifier_call_chain+0x82/0xb0
	[<c0170d8f>] raw_notifier_call_chain+0x1f/0x30
	[<c053b86c>] call_netdevice_notifiers+0x2c/0x60
	[<c0182184>] ? trace_hardirqs_on_caller+0xf4/0x180
	[<c053b8ec>] __dev_close_many+0x4c/0xd0
	[<c053ba2d>] dev_close_many+0x6d/0xc0
	[<c053bb53>] rollback_registered_many+0x93/0x1c0
	[<c018221b>] ? trace_hardirqs_on+0xb/0x10
	[<c053bc95>] unregister_netdevice_many+0x15/0x50
	[<fb07f83b>] ieee80211_remove_interfaces+0x7b/0xb0
	[mac80211]
	[<fb06a14b>] ieee80211_unregister_hw+0x4b/0x110
	[mac80211]
	[<fb311a4a>] ath9k_deinit_device+0x3a/0x60 [ath9k]
	[<fb31eed6>] ath_pci_remove+0x46/0x90 [ath9k]
	[<c03b4ac4>] pci_device_remove+0x44/0x100
	[<c043eb54>] __device_release_driver+0x64/0xb0
	[<c043ec67>] device_release_driver+0x27/0x40
	[<c043deeb>] bus_remove_device+0x7b/0xa0
	[<c043c491>] device_del+0xf1/0x180
	[<c043c530>] device_unregister+0x10/0x20
	[<c03afafe>] pci_stop_bus_device+0x6e/0x80
	[<c03afb72>] pci_remove_bus_device+0x12/0xa0
	[<c03c2f29>] pciehp_unconfigure_device+0x89/0x180
	[<c0181e54>] ? mark_held_locks+0x64/0x100
	[<c063390f>] ? __mutex_unlock_slowpath+0xaf/0x140
	[<c03c1f84>] pciehp_disable_slot+0x64/0x1b0
	[<c03c2850>] pciehp_power_thread+0xd0/0x100
	[<c0164ad0>] ? process_one_work+0x100/0x4d0
	[<c0164b4c>] process_one_work+0x17c/0x4d0
	[<c0164ad0>] ? process_one_work+0x100/0x4d0
	[<c03c2780>] ? queue_interrupt_event+0xa0/0xa0
	[<c01662bb>] worker_thread+0x13b/0x320
	[<c018221b>] ? trace_hardirqs_on+0xb/0x10
	[<c0166180>] ? manage_workers+0x1e0/0x1e0
	[<c016a654>] kthread+0x84/0x90
	[<c016a5d0>] ? __init_kthread_worker+0x60/0x60
	[<c063d106>] kernel_thread_helper+0x6/0x10

Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Since my commit 34e89507
("mac80211: allow station add/remove to sleep") there is
a race in mac80211 when it clears the TIM bit because a
sleeping station disconnected, the spinlock isn't held
around the relevant code any more. Use the right API to
acquire the spinlock correctly.

Cc: stable@kernel.org [2.6.34+]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The driver fails to clear encryption keys making it impossible
to switch connections.
Signed-off-by: George <george0505@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org>        [2.6.39+]
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The driver fails to connect to 802.11n-enabled APs. The patch fixes
Bug #42262.
Signed-off-by: George <george0505@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org>        [2.6.39+]
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ADC calibrations cannot run on 5 GHz with fast clock enabled. They
need to be disabled, otherwise they'll hang and IQ mismatch calibration
will not be run either.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Adrian Chadd <adrian@freebsd.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When trying to connect to 5GHz we can provide negative index to
mac80211 what trigger BUG_ON. Reason of iwl-3945-rs malfunction
on 5GHz is unknown and needs further investigation. For now, to
do not trigger a bug, correct value and just print WARNING.

Address bug:
https://bugzilla.redhat.com/show_bug.cgi?id=730653Reported-and-tested-by: Jan Teichmann <jan.teichmann@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The commit 172805ad
overwirtes additional clock settings of AR9330 to
all AR9300 chips.

Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

__netpoll_rx() doesnt properly handle skbs with small header

pskb_may_pull() or pskb_trim_rcsum() can change skb->data, we must
reload it.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Spotted-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In ti_hecc_probe(), the spinlock  priv->mbx_lock is not
inited, causing a spinlock lockup BUG.
Acked-by: Anant Gole <anantgole@ti.com>
Signed-off-by: Abhilash K V <abhilash.kv@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>