- 04 Oct, 2018 17 commits
-
-
Jacopo Mondi authored
The adv748x assumes input endpoints are always enabled, and registers a subdevice for each of them when the corresponding output subdevice is registered. Fix this by conditionally registering the input subdevice only if it is actually described in device tree. Tested-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
Jacopo Mondi <jacopo+renesas@jmondi.org> Signed-off-by:
Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-
Jacopo Mondi authored
The ADV748x has two CSI-2 output port and one TTL input/output port for digital video reception/transmission. The TTL digital pad is unconditionally enabled during the device reset even if not used. Same goes for the TXA and TXB CSI-2 outputs, which are enabled by the initial settings blob programmed into the chip. In order to improve power saving, do not enable unused output interfaces: keep TTL output disabled, as it is not used, and drop CSI-2 output enabling from the initial settings list, as they get conditionally enabled later. Tested-by:
-
Jacopo Mondi authored
As the driver is now allowed to probe with a single output endpoint, power management routines shall now take into account the case a CSI-2 TX is not enabled. Unify the adv748x_tx_power() routine to handle transparently TXA and TXB, and enable the CSI-2 outputs conditionally. Tested-by:
-
Jacopo Mondi authored
Currently the adv748x driver will fail to probe unless both of its output endpoints (TXA and TXB) are connected. Make the driver support probing provided that there is at least one input, and one output connected and protect the clean-up function from accessing un-initialized fields. Following patches will fix other uses of un-initialized TXs in the driver, such as power management functions. Tested-by:
-
Benjamin Gaignard authored
STI CEC driver has move from staging directory to media/platform/sti/cec/ Signed-off-by:
Benjamin Gaignard <benjamin.gaignard@st.com> Signed-off-by:
-
Colin Ian King authored
Trivial fix to spelling mistake in kernel warning message Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
Niklas Söderlund authored
When adding support for parallel subdev for Gen3 it was missed that the symbol 'i' in rvin_group_link_notify() was already declared, remove the dupe as it's only used as a loop variable this have no functional change. This fixes warning: rcar-core.c:117:52: originally declared here rcar-core.c:173:30: warning: symbol 'i' shadows an earlier one Fixes: 1284605d ("media: rcar-vin: Handle parallel subdev in link_notify") Signed-off-by:Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Acked-by:
-
Arnd Bergmann authored
The newly added driver fails to build in some configurations due to a missing header inclusion: drivers/media/platform/imx-pxp.c:988:8: error: unknown type name 'irqreturn_t' static irqreturn_t pxp_irq_handler(int irq, void *dev_id) ^~~~~~~~~~~ drivers/media/platform/imx-pxp.c: In function 'pxp_irq_handler': drivers/media/platform/imx-pxp.c:1012:9: error: 'IRQ_HANDLED' undeclared (first use in this function); did you mean 'IRQ_MODE'? return IRQ_HANDLED; ^~~~~~~~~~~ IRQ_MODE drivers/media/platform/imx-pxp.c:1012:9: note: each undeclared identifier is reported only once for each function it appears in drivers/media/platform/imx-pxp.c: In function 'pxp_probe': drivers/media/platform/imx-pxp.c:1660:8: error: implicit declaration of function 'devm_request_threaded_irq'; did you mean 'devm_request_region'? [-Werror=implicit-function-declaration] ret = devm_request_threaded_irq(&pdev->dev, irq, NULL, pxp_irq_handler, ^~~~~~~~~~~~~~~~~~~~~~~~~ devm_request_region drivers/media/platform/imx-pxp.c:1661:4: error: 'IRQF_ONESHOT' undeclared (first use in this function); did you mean 'SA_ONESHOT'? IRQF_ONESHOT, dev_name(&pdev->dev), dev); Fixes: 51abcf7f ("media: imx-pxp: add i.MX Pixel Pipeline driver") Signed-off-by:Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Hugues Fruchet authored
Only enable IT frame on JPEG capture, this saves some CPU interruptions and processing on all the other cases. Signed-off-by:
Hugues Fruchet <hugues.fruchet@st.com> Signed-off-by:
-
Nathan Chancellor authored
Clang warns that the address of a pointer will always evaluated as true in a boolean context. drivers/media/platform/pxa_camera.c:2400:17: warning: address of 'pdev->dev.of_node' will always evaluate to 'true' [-Wpointer-bool-conversion] if (&pdev->dev.of_node && !pcdev->pdata) { ~~~~~~~~~~^~~~~~~ ~~ 1 warning generated. Judging from the rest of the kernel, it seems like this was an error and just the value of of_node should be checked rather than the address. Reported-by:Nick Desaulniers <ndesaulniers@google.com> Signed-off-by:
Nathan Chancellor <natechancellor@gmail.com> Reviewed-by:
-
zhong jiang authored
We include device.h twice in camss.h. It's unnecessary. hence just remove it. Signed-off-by:
zhong jiang <zhongjiang@huawei.com> Acked-by:
Todor Tomov <todor.tomov@linaro.org> Signed-off-by:
-
Philipp Zabel authored
The documentation in Documentation/media/uapi/v4l/pixfmt-packed-rgb.rst tells us that the V4L2_PIX_FMT_RGB32 format is deprecated and must not be used by new drivers. Replace it with V4L2_PIX_FMT_XRGB32. Signed-off-by:
Philipp Zabel <p.zabel@pengutronix.de> Acked-by:
Steve Longerbeam <steve_longerbeam@mentor.com> Signed-off-by:
-
Dan Carpenter authored
The load_requested_vpu() function returns a freed vpu_fw pointer. It's not used so it doesn't cause any problems, but Smatch complains about it: drivers/media/platform/mtk-vpu/mtk_vpu.c:578 vpu_load_firmware() warn: passing freed memory 'vpu_fw' We can clean up the code a bit and silence the static checker warning by not passing the parameter at all. Signed-off-by:Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Hans Verkuil authored
Clarify that when you receive V4L2_EVENT_SOURCE_CHANGE with flag V4L2_EVENT_SRC_CH_RESOLUTION set, and the new resolution appears identical to the old resolution, then you still must restart the streaming I/O. Signed-off-by:
Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by:
-
Matthias Reichl authored
The Kathrein RCU-676 remote uses the 32-bit rc6 protocol and toggles bit 15 (0x8000) on repeated button presses, like MCE remotes. Add it's customer code 0x80460000 to the 32-bit rc6 toggle handling code to get proper scancodes and toggle reports. Signed-off-by:
Matthias Reichl <hias@horus.com> Signed-off-by:
Sean Young <sean@mess.org> Signed-off-by:
-
Sean Young authored
This can be done with c99 initializers, which makes the code cleaner and more transparent. It does require gcc 4.6, because of this bug in earlier versions: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=10676 Since commit cafa0010 ("Raise the minimum required gcc version to 4.6"), this is the case. Signed-off-by:
-
Sean Young authored
The rc_proto field should list the exact variant used by the remote. This does not change the decoder used, but helps with using keymaps for transmit purposes. Signed-off-by:
-
- 03 Oct, 2018 4 commits
-
-
Ricardo Ribalda Delgado authored
The loop seemed to be made to calculate max, but max is not used in that function. Signed-off-by:
Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Signed-off-by:
-
Hugues Fruchet authored
Change 720p JPEG mode to mode 3 as per other resolutions. Signed-off-by:
-
Sakari Ailus authored
The V4L2 sub-device API does not support the crop default target. A number of drivers apparently still did support this, likely as it was needed by the SoC camera framework. Drop support for the default crop rectaingle in sub-device drivers, and use the bounds rectangle in SoC camera instead. Reported-by:
Helmut Grohne <h.grohne@intenta.de> Suggested-by:
-
Sakari Ailus authored
A number of sub-device drivers used a static name for the sub-device, and thus the media entity. As the entity name must be unique within a media device, this makes it impossible to have more than one instance of each device in a media device. This is a rather severe limitation. Instead of fixing these drivers, add a comment to the drivers noting that such static names may not be used in the future. The alternative of fixing the drivers is troublesome as the entity (as well as sub-device) name is part of the uAPI. Changing that is almost certain to break something. As these devices are old but no-one has encountered a problem with the static names, leave it as-is. Signed-off-by:
-
- 24 Sep, 2018 19 commits
-
-
Nathan Chancellor authored
Clang warns when one enumerated type is implicitly converted to another. drivers/media/platform/davinci/vpbe_display.c:524:24: warning: implicit conversion from enumeration type 'enum osd_v_exp_ratio' to different enumeration type 'enum osd_h_exp_ratio' [-Wenum-conversion] layer_info->h_exp = V_EXP_6_OVER_5; ~ ^~~~~~~~~~~~~~ 1 warning generated. This appears to be a copy and paste error judging from the couple of lines directly above this statement and the way that height is handled in the if block above this one. Reported-by: -
Nathan Chancellor authored
Clang warns when a variable is assigned to itself. drivers/media/pci/bt8xx/bttv-driver.c:2043:13: warning: explicitly assigning value of variable of type '__s32' (aka 'int') to itself [-Wself-assign] min_height = min_height; ~~~~~~~~~~ ^ ~~~~~~~~~~ 1 warning generated. There doesn't appear to be any good reason for this and this statement was added in commit e5bd0260 ("V4L/DVB (5077): Bttv cropping support") back in 2007. Just remove it. Reported-by: -
Niklas Söderlund authored
Signed-off-by:
Simon Horman <horms+renesas@verge.net.au> Signed-off-by:
-
Nicholas Mc Guire authored
altera_hw_filt_init() which calls append_internal() assumes that the node was successfully linked in while in fact it can silently fail. So the call-site needs to set return to -ENOMEM on append_internal() returning NULL and exit through the err path. Fixes: 349bcf02 ("[media] Altera FPGA based CI driver module") Signed-off-by:
Nicholas Mc Guire <hofrat@osadl.org> Signed-off-by:
-
Brad Love authored
Correcting red herring error messages. Where appropriate, replaces au0282_dev_register with: - au0828_analog_register - au0828_dvb_register Signed-off-by:
Brad Love <brad@nextdimension.cc> Signed-off-by:
-
Brad Love authored
If au0828_analog_register fails, the dev is kfree'd and then flow jumps to done, which can call au0828_usb_disconnect. Since all USB error codes are negative, au0828_usb_disconnect will be called. The problem is au0828_usb_disconnect uses dev, if dev is NULL then there is immediate oops encountered. [ 7.454307] au0828: au0828_usb_probe() au0282_dev_register failed to register on V4L2 [ 7.454323] BUG: unable to handle kernel NULL pointer dereference at 0000000000000050 [ 7.454421] PGD 0 P4D 0 [ 7.454457] Oops: 0002 [#1] SMP PTI [ 7.454500] CPU: 1 PID: 262 Comm: systemd-udevd Tainted: P O 4.18.3 #1 [ 7.454584] Hardware name: Google Panther/Panther, BIOS MattDevo 04/27/2015 [ 7.454670] RIP: 0010:_raw_spin_lock_irqsave+0x2c/0x50 [ 7.454725] Code: 44 00 00 55 48 89 e5 41 54 53 48 89 fb 9c 58 0f 1f 44 00 00 49 89 c4 fa 66 0f 1f 44 00 00 e8 db 23 1b ff 31 c0 ba 01 00 00 00 <f0> 0f b1 13 85 c0 75 08 4c 89 e0 5b 41 5c 5d c3 89 c6 48 89 df e8 [ 7.455004] RSP: 0018:ffff9130f53ef988 EFLAGS: 00010046 [ 7.455063] RAX: 0000000000000000 RBX: 0000000000000050 RCX: 0000000000000000 [ 7.455139] RDX: 0000000000000001 RSI: 0000000000000003 RDI: 0000000000000050 [ 7.455216] RBP: ffff9130f53ef998 R08: 0000000000000018 R09: 0000000000000090 [ 7.455292] R10: ffffed4cc53cb000 R11: ffffed4cc53cb108 R12: 0000000000000082 [ 7.455369] R13: ffff9130cf2c6188 R14: 0000000000000000 R15: 0000000000000018 [ 7.455447] FS: 00007f2ff8514cc0(0000) GS:ffff9130fcb00000(0000) knlGS:0000000000000000 [ 7.455535] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 7.455597] CR2: 0000000000000050 CR3: 00000001753f0002 CR4: 00000000000606a0 [ 7.455675] Call Trace: [ 7.455713] __wake_up_common_lock+0x65/0xc0 [ 7.455764] __wake_up+0x13/0x20 [ 7.455808] ir_lirc_unregister+0x57/0xe0 [rc_core] [ 7.455865] rc_unregister_device+0xa0/0xc0 [rc_core] [ 7.455935] au0828_rc_unregister+0x25/0x40 [au0828] [ 7.455999] au0828_usb_disconnect+0x33/0x80 [au0828] [ 7.456064] au0828_usb_probe.cold.16+0x8d/0x2aa [au0828] [ 7.456130] usb_probe_interface+0xf1/0x300 [ 7.456184] driver_probe_device+0x2e3/0x460 [ 7.456235] __driver_attach+0xe4/0x110 [ 7.456282] ? driver_probe_device+0x460/0x460 [ 7.456335] bus_for_each_dev+0x74/0xb0 [ 7.456385] ? kmem_cache_alloc_trace+0x15d/0x1d0 [ 7.456441] driver_attach+0x1e/0x20 [ 7.456485] bus_add_driver+0x159/0x230 [ 7.456532] driver_register+0x70/0xc0 [ 7.456578] usb_register_driver+0x7f/0x140 [ 7.456626] ? 0xffffffffc0474000 [ 7.456674] au0828_init+0xbc/0x1000 [au0828] [ 7.456725] do_one_initcall+0x4a/0x1c9 [ 7.456771] ? _cond_resched+0x19/0x30 [ 7.456817] ? kmem_cache_alloc_trace+0x15d/0x1d0 [ 7.456873] do_init_module+0x60/0x210 [ 7.456918] load_module+0x221b/0x2710 [ 7.456966] ? vfs_read+0xf5/0x120 [ 7.457010] __do_sys_finit_module+0xbd/0x120 [ 7.457061] ? __do_sys_finit_module+0xbd/0x120 [ 7.457115] __x64_sys_finit_module+0x1a/0x20 [ 7.457166] do_syscall_64+0x5b/0x110 [ 7.457210] entry_SYSCALL_64_after_hwframe+0x49/0xbe Signed-off-by:
-
Gustavo A. R. Silva authored
Return statements in functions returning bool should use true or false instead of an integer value. This code was detected with the help of Coccinelle. Signed-off-by:
Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by:
-
Lucas Stach authored
On a decoder instance, after the profile has been parsed from the stream __v4l2_ctrl_s_ctrl() is called to notify userspace about changes in the read-only profile control. This ends up calling back into the CODA driver where a missing check on the s_ctrl caused the profile information that has just been parsed from the stream to be overwritten with the default baseline profile. Later on the driver fails to enable frame reordering, based on the wrong profile information. Fixes: 347de126d1da (media: coda: add read-only h.264 decoder profile/level controls) Signed-off-by:Lucas Stach <l.stach@pengutronix.de> Reviewed-by:
-
Johan Fjeldtvedt authored
Warn and return error from the reqbufs ioctl when driver sets 0 number of planes or 0 as plane sizes, as these values don't make any sense. Checking this here stops obviously wrong values from propagating further and causing various problems that are hard to trace back to either of these values being 0. Signed-off-by:
Johan Fjeldtvedt <johfjeld@cisco.com> Acked-by:
-
zhong jiang authored
of_node_put has taken the null pinter check into account. So it is safe to remove the duplicated check before of_node_put. Signed-off-by:
Benoit Parrot <bparrot@ti.com> Signed-off-by:
-
zhong jiang authored
of_node_put has taken the null pointer check into account. So it is safe to remove the duplicated check before of_node_put. Signed-off-by:
-
Hans Verkuil authored
Drop all Adobe references and use the official opRGB standard instead. Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by:
-
Hans Verkuil authored
These names have been renamed in the CTA-861 standard due to trademark issues. Replace them here as well so they are in sync with the standard. Signed-off-by:
Hans Verkuil <hansverk@cisco.com> Cc: stable@vger.kernel.org Acked-by:
-
Hans Verkuil authored
The CTA-861 standards have been updated to refer to opRGB instead of AdobeRGB. The official standard is in fact named opRGB, so switch to that. The two old defines referring to ADOBERGB in the public API are put under #ifndef __KERNEL__ and a comment mentions that they are deprecated. Signed-off-by:
-
Philipp Zabel authored
Include the missing interrupt.h header to fix compilation on i386 or x86_64: ../drivers/media/platform/imx-pxp.c:988:1: error: unknown type name 'irqreturn_t' static irqreturn_t pxp_irq_handler(int irq, void *dev_id) ^ ../drivers/media/platform/imx-pxp.c: In function 'pxp_irq_handler': ../drivers/media/platform/imx-pxp.c:1012:9: error: 'IRQ_HANDLED' undeclared (first use in this function) return IRQ_HANDLED; ^ ../drivers/media/platform/imx-pxp.c:1012:9: note: each undeclared identifier is reported only once for each function it appears in ../drivers/media/platform/imx-pxp.c: In function 'pxp_probe': ../drivers/media/platform/imx-pxp.c:1660:2: error: implicit declaration of function 'devm_request_threaded_irq' [-Werror=implicit-function-declaration] ret = devm_request_threaded_irq(&pdev->dev, irq, NULL, pxp_irq_handler, ^ ../drivers/media/platform/imx-pxp.c:1661:4: error: 'IRQF_ONESHOT' undeclared (first use in this function) IRQF_ONESHOT, dev_name(&pdev->dev), dev); Fixes: 51abcf7f ("media: imx-pxp: add i.MX Pixel Pipeline driver") Reported-by:Randy Dunlap <rdunlap@infradead.org> Signed-off-by:
-
Ezequiel Garcia authored
The vicodec does not use the aborting field. In fact, this driver can't really cancel any work, since it performs all the work in device_run(). Signed-off-by:
Ezequiel Garcia <ezequiel@collabora.com> Signed-off-by:
-
Ezequiel Garcia authored
The vicodec doesn't use the Subdev API, so drop the dependency. Signed-off-by:
-
Hans Verkuil authored
state->info was NULL since I completely forgot to set state->info. Oops. Signed-off-by:
-
Hans Verkuil authored
These functions did not return an error if state->info was NULL or an unsupported pixelformat was selected (should not happen, but just to be on the safe side). Signed-off-by:
-
