Create mlx5_devlink_health_reporter for FW reporter. The FW reporter
implements devlink_health_reporter diagnose callback.

The fw reporter diagnose command can be triggered any time by the user
to check current fw status.
In healthy status, it will return clear syndrome. Otherwise it will
return the syndrome and description of the error type.

Command example and output on healthy status:
$ devlink health diagnose pci/0000:82:00.0 reporter fw
Syndrome: 0

Command example and output on non healthy status:
$ devlink health diagnose pci/0000:82:00.0 reporter fw
Syndrome: 8 Description: unrecoverable hardware error
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

If a FW assert is considered fatal, indicated by a new bit in the health
buffer, reset the FW. After the reset go through the normal recovery
flow. Only one PF needs to issue the reset, so an attempt is made to
prevent the 2nd function from also issuing the reset.
It's not an error if that happens, it just slows recovery.
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Since the FW can be shared between different PFs/VFs it is common
that more than one health poll will detected a failure, this can
lead to multiple resets which are unneeded.

The solution is to use a FW locking mechanism using semaphore space
to provide a way to allow only one device to collect the cr-dump and
to issue a sw-reset.
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

New mlx5 adapters allow the driver to reset the FW in the event of an
error, this action called "SW Reset". When an SW reset is issued on any
PF all PFs enter reset state which is a recoverable condition. The
existing recovery flow was designed to allow the recovery of a VF after
a PF driver reload. This patch adds the sw reset to the NIC states
as a preparation for sw reset handling.

When a software reset is issued the following occurs:
1. The NIC interface mode is set to 7 while the reset is in progress.
2. Once the reset completes the NIC interface mode is set to 1.
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Crdump allows the driver to retrieve a dump of the FW PCI crspace.
This is useful in case of catastrophic issues which may require FW
reset. The crspace dump can be used for later debug.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

The Vendor Specific Capability (VSC) is used to activate a gateway
interfacing with the device. The gateway is used to read or write
device configurations, which are organized in different domains (spaces).
A configuration access may result in multiple actions, reads, writes.

Example usages are accessing the Crspace domain to read the crspace or
locking a device semaphore using the Semaphore domain.

The configuration access use pci_cfg_access to prevent parallel access to
the VSC space by the driver and userspace calls.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Centralize all devlink related callbacks in one file.
In the downstream patch, some more functionality will be added, this
patch is preparing the driver infrastructure for it.

Currently, move devlink un/register functions calls into this file.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Add initial documentation for mlx5 driver.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

The devlink health reporter provides a dump method on an error. Dump
may contain a large amount of data, in this case doit cb isn't sufficient.
This is because the user side is blocking and doesn't allow draining of
the socket until the socket runs out of buffers. Using dumpit cb
is the correct way to go.
Please note that thankfully the dump op is not yet implemented in any
driver and therefore this change is not breaking userspace.

Fixes: 35455e23 ("devlink: Add health dump {get,clear} commands")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Adding delays to TCP flows is crucial for studying behavior
of TCP stacks, including congestion control modules.

Linux offers netem module, but it has unpractical constraints :
- Need root access to change qdisc
- Hard to setup on egress if combined with non trivial qdisc like FQ
- Single delay for all flows.

EDT (Earliest Departure Time) adoption in TCP stack allows us
to enable a per socket delay at a very small cost.

Networking tools can now establish thousands of flows, each of them
with a different delay, simulating real world conditions.

This requires FQ packet scheduler or a EDT-enabled NIC.

This patchs adds TCP_TX_DELAY socket option, to set a delay in
usec units.

  unsigned int tx_delay = 10000; /* 10 msec */

  setsockopt(fd, SOL_TCP, TCP_TX_DELAY, &tx_delay, sizeof(tx_delay));

Note that FQ packet scheduler limits might need some tweaking :

man tc-fq

PARAMETERS
   limit
       Hard  limit  on  the  real  queue  size. When this limit is
       reached, new packets are dropped. If the value is  lowered,
       packets  are  dropped so that the new limit is met. Default
       is 10000 packets.

   flow_limit
       Hard limit on the maximum  number  of  packets  queued  per
       flow.  Default value is 100.

Use of TCP_TX_DELAY option will increase number of skbs in FQ qdisc,
so packets would be dropped if any of the previous limit is hit.

Use of a jump label makes this support runtime-free, for hosts
never using the option.

Also note that TSQ (TCP Small Queues) limits are slightly changed
with this patch : we need to account that skbs artificially delayed
wont stop us providind more skbs to feed the pipe (netem uses
skb_orphan_partial() for this purpose, but FQ can not use this trick)

Because of that, using big delays might very well trigger
old bugs in TSO auto defer logic and/or sndbuf limited detection.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sameeh Jubran says:

====================
Support for dynamic queue size changes

This patchset introduces the following:
* add new admin command for supporting different queue size for Tx/Rx
* add support for Tx/Rx queues size modification through ethtool
* allow queues allocation backoff when low on memory
* update driver version

Difference from v2:
* Dropped superfluous range checks which are already done in ethtool. [patch 5/7]
* Dropped inline keyword from function. [patch 4/7]
* Added a new patch which drops inline keyword all *.c files. [patch 6/7]

Difference from v1:
* Changed ena_update_queue_sizes() signature to use u32 instead of int
  type for the size arguments. [patch 5/7]
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Update driver version to match device specification.
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Let the compiler decide if the function should be inline in *.c files
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement the set_ringparam() function of the ethtool interface
to enable the changing of io queue sizes.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If there is not enough memory to allocate io queues the driver will
try to allocate smaller queues.

The backoff algorithm is as follows:

1. Try to allocate TX and RX and if successful.
1.1. return success

2. Divide by 2 the size of the larger of RX and TX queues (or both if their size is the same).

3. If TX or RX is smaller than 256
3.1. return failure.
4. else
4.1. go back to 1.

Also change the tx_queue_size, rx_queue_size field names in struct
adapter to requested_tx_queue_size and requested_rx_queue_size, and
use RX and TX queue 0 for actual queue sizes.
Explanation:
The original fields were useless as they were simply used to assign
values once from them to each of the queues in the adapter in ena_probe().
They could simply be deleted. However now that we have a backoff
feature, we have use for them. In case of backoff there is a difference
between the requested queue sizes and the actual sizes. Therefore there
is a need to save the requested queue size for future retries of queue
allocation (for example if allocation failed and then ifdown + ifup was
called we want to start the allocation from the original requested size of
the queues).
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently ethtool -g shows the same size for current and max queue
sizes.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use MAX_QUEUES_EXT get feature capability to query the device.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a new admin command to support different queue size for Tx/Rx
queues (the change also support different SQ/CQ sizes)
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ioana Radulescu says:

====================
dpaa2-eth: Add support for MQPRIO offloading

Add support for adding multiple TX traffic classes with mqprio. We can have
up to one netdev queue and hardware frame queue per TC per core.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement mqprio qdisc support by mapping traffic classes to
different hardware enqueue priorities. The maximum number of
supported traffic classes is an attribute of each DPNI object.

The traffic classes map to hardware priorities from highest (0)
to lowest (highest prio number). The skb priority information
received from the stack is used to select the hardware Tx queue
on which to enqueue the frame.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Bogdan Purcareata <bogdan.purcareata@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

DPNI objects can have multiple traffic classes, as reflected by
the num_tc attribute. Until now we ignored its value and only
used traffic class 0.

This patch adds support for multiple Tx traffic classes; we have
num_queues x num_tcs hardware queues available for each interface.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the code configuring xps on the netdev TX queues to a
separate function. A subsequent patch will need to call
this in another context as well.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add dependency to TI CPTS from Common CLK framework COMMON_CLK to fix
allyesconfig build for Powerpc:

drivers/net/ethernet/ti/cpts.c: In function 'cpts_of_mux_clk_setup':
drivers/net/ethernet/ti/cpts.c:567:2: error: implicit declaration of function 'of_clk_parent_fill'; did you mean 'of_clk_get_parent_name'? [-Werror=implicit-function-declaration]
  of_clk_parent_fill(refclk_np, parent_names, num_parents);
  ^~~~~~~~~~~~~~~~~~
  of_clk_get_parent_name

Fixes: a3047a81 ("net: ethernet: ti: cpts: add support for ext rftclk selection")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We need to specifically deal with phylink_of_phy_connect() returning
-ENODEV, because this can happen when a CPU/DSA port does connect
neither to a PHY, nor has a fixed-link property. This is a valid use
case that is permitted by the binding and indicates to the switch:
auto-configure port with maximum capabilities.

Fixes: 0e279218 ("net: dsa: Use PHYLINK for the CPU/DSA ports")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

During a port FDB dump operation, the mutex protecting the concurrent
access to the switch registers is currently held by the internal
mv88e6xxx_port_db_dump and mv88e6xxx_port_db_dump_fid helpers.

It must be held at the higher level in mv88e6xxx_port_fdb_dump which
is called directly by DSA through ds->ops->port_fdb_dump. Fix this.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add bindings for Wiznet's w5x00 series of SPI interfaced Ethernet chips.

Based on the bindings for microchip,enc28j60.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The w5X00 chip provides an SPI to Ethernet inteface. This patch allows
platform devices to be defined through the device tree.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

To remove rtnl lock dependency in tc filter update API when using ingress
Qdisc, set QDISC_CLASS_OPS_DOIT_UNLOCKED flag in ingress Qdisc_class_ops.

Ingress Qdisc ops don't require any modifications to be used without rtnl
lock on tc filter update path. Ingress implementation never changes its
q->block and only releases it when Qdisc is being destroyed. This means it
is enough for RTM_{NEWTFILTER|DELTFILTER|GETTFILTER} message handlers to
hold ingress Qdisc reference while using it without relying on rtnl lock
protection. Unlocked Qdisc ops support is already implemented in filter
update path by unlocked cls API patch set.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jakub Kicinski says:

====================
tls: add support for kernel-driven resync and nfp RX offload

This series adds TLS RX offload for NFP and completes the offload
by providing resync strategies.  When TLS data stream looses segments
or experiences reorder NIC can no longer perform in line offload.
Resyncs provide information about placement of records in the
stream so that offload can resume.

Existing TLS resync mechanisms are not a great fit for the NFP.
In particular the TX resync is hard to implement for packet-centric
NICs.  This patchset adds an ability to perform TX resync in a way
similar to the way initial sync is done - by calling down to the
driver when new record is created after driver indicated sync had
been lost.

Similarly on the RX side, we try to wait for a gap in the stream
and send record information for the next record.  This works very
well for RPC workloads which are the primary focus at this time.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When TCP stream gets out of sync (driver stops receiving skbs
with expected TCP sequence numbers) request a TX resync from
the kernel.

We try to distinguish retransmissions from missed transmissions
by comparing the sequence number to expected - if it's further
than the expected one - we probably missed packets.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

TLS offload drivers keep track of TCP seq numbers to make sure
the packets are fed into the HW in order.

When packets get dropped on the way through the stack, the driver
will get out of sync and have to use fallback encryption, but unless
TCP seq number is resynced it will never match the packets correctly
(or even worse - use incorrect record sequence number after TCP seq
wraps).

Existing drivers (mlx5) feed the entire record on every out-of-order
event, allowing FW/HW to always be in sync.

This patch adds an alternative, more akin to the RX resync.  When
driver sees a frame which is past its expected sequence number the
stream must have gotten out of order (if the sequence number is
smaller than expected its likely a retransmission which doesn't
require resync).  Driver will ask the stack to perform TX sync
before it submits the next full record, and fall back to software
crypto until stack has performed the sync.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently only RX direction is ever resynced, however, TX may
also get out of sequence if packets get dropped on the way to
the driver.  Rename the resync callback and add a direction
parameter.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Set ethtool TLS RX feature based on NIC capabilities, and enable
TLS RX when connections are added for decryption.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Enable kernel-controlled RX resync and propagate TLS connection
RX resync from kernel TLS to firmware.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some control messages must be sent from atomic context.  The mailbox
takes sleeping locks and uses a waitqueue so add a "posted" version
of communication.

Trylock the semaphore and if that's successful kick of the device
communication.  The device communication will be completed from
a workqueue, which will also release the semaphore.

If locks are taken queue the message and return.  Schedule a
different workqueue to take the semaphore and run the communication.
Note that the there are currently no atomic users which would actually
need the return value, so all replies to posted messages are just
freed.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We need the name nfp_ccm_mbox_alloc() for allocating the mailbox
communication channel itself.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Firmware indicates when a packet has been decrypted by reusing the
currently unused BPF flag.  Transfer this information into the skb
and provide a statistic of all decrypted segments.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

TLS offload device may lose sync with the TCP stream if packets
arrive out of order.  Drivers can currently request a resync at
a specific TCP sequence number.  When a record is found starting
at that sequence number kernel will inform the device of the
corresponding record number.

This requires the device to constantly scan the stream for a
known pattern (constant bytes of the header) after sync is lost.

This patch adds an alternative approach which is entirely under
the control of the kernel.  Kernel tracks records it had to fully
decrypt, even though TLS socket is in TLS_HW mode.  If multiple
records did not have any decrypted parts - it's a pretty strong
indication that the device is out of sync.

We choose the min number of fully encrypted records to be 2,
which should hopefully be more than will get retransmitted at
a time.

After kernel decides the device is out of sync it schedules a
resync request.  If the TCP socket is empty the resync gets
performed immediately.  If socket is not empty we leave the
record parser to resync when next record comes.

Before resync in message parser we peek at the TCP socket and
don't attempt the sync if the socket already has some of the
next record queued.

On resync failure (encrypted data continues to flow in) we
retry with exponential backoff, up to once every 128 records
(with a 16k record thats at most once every 2M of data).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

handle_device_resync() doesn't describe the function very well.
The function checks if resync should be issued upon parsing of
a new record.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

TLS offload code casts record number to a u64.  The buffer
should be aligned to 8 bytes, but its actually a __be64, and
the rest of the TLS code treats it as big int.  Make the
offload callbacks take a byte array, drivers can make the
choice to do the ugly cast if they want to.

Prepare for copying the record number onto the stack by
defining a constant for max size of the byte array.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>