Support for loading the Renesas HSPI driver via devicetree.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>

In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should be
replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>

Current code keeps the clocks enabled all the time, it wastes the power
when there is no operaiton on the spi controller.

In order to save the power, this patch adds the two hooks:
   spi_imx_prepare_message: enable the clocks for this message
   spi_imx_unprepare_message: disable the clocks.

This patch also disables the clocks in the end of the probe.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>

Pull btrfs fix from Chris Mason:
 "Sage hit a deadlock with ceph on btrfs, and Josef tracked it down to a
  regression in our initial rc1 pull.  When doing nocow writes we were
  sometimes starting a transaction with locks held"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: release path before starting transaction in can_nocow_extent

Pull ACPI and power management fixes from Rafael Wysocki:

 - intel_pstate fix for misbehavior after system resume if sysfs
   attributes are set in a specific way before the corresponding suspend
   from Dirk Brandewie.

 - A recent intel_pstate fix has no effect if unsigned long is 32-bit,
   so fix it up to cover that case as well.

 - The s3c64xx cpufreq driver was not updated when the index field of
   struct cpufreq_frequency_table was replaced with driver_data, so
   update it now.  From Charles Keepax.

 - The Kconfig help text for ACPI_BUTTON still refers to
   /proc/acpi/event that has been dropped recently, so modify it to
   remove that reference.  From Krzysztof Mazur.

 - A Lan Tianyu's change adds a missing mutex unlock to an error code
   path in acpi_resume_power_resources().

 - Some code related to ACPI power resources, whose very purpose is
   questionable to put it lightly, turns out to cause problems to happen
   during testing on real systems, so remove it completely (we may
   revisit that in the future if there's a compelling enough reason).
   From Rafael J Wysocki and Aaron Lu.

* tag 'pm+acpi-3.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI / PM: Drop two functions that are not used any more
  ATA / ACPI: remove power dependent device handling
  cpufreq: s3c64xx: Rename index to driver_data
  ACPI / power: Drop automaitc resume of power resource dependent devices
  intel_pstate: Fix type mismatch warning
  cpufreq / intel_pstate: Fix max_perf_pct on resume
  ACPI: remove /proc/acpi/event from ACPI_BUTTON help
  ACPI / power: Release resource_lock after acpi_power_get_state() return error

Pull x86 fixes from Ingo Molnar:
 "Two fixlets:

   - fix a (rare-config) build bug
   - fix a next-gen SGI/UV hw/firmware enumeration bug"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86: Update UV3 hub revision ID
  x86/microcode: Correct Kconfig dependencies

We can't be holding tree locks while we try to start a transaction, we will
deadlock.  Thanks,
Reported-by: Sage Weil <sage@inktank.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>

* acpi-fixes:
  ACPI / PM: Drop two functions that are not used any more
  ATA / ACPI: remove power dependent device handling
  ACPI / power: Drop automaitc resume of power resource dependent devices
  ACPI: remove /proc/acpi/event from ACPI_BUTTON help
  ACPI / power: Release resource_lock after acpi_power_get_state() return error

* pm-fixes:
  cpufreq: s3c64xx: Rename index to driver_data
  intel_pstate: Fix type mismatch warning
  cpufreq / intel_pstate: Fix max_perf_pct on resume

Pull CIFS fixes from Steve French:
 "Five small cifs fixes (includes fixes for: unmount hang, 2 security
  related, symlink, large file writes)"

* 'for-linus' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: ntstatus_to_dos_map[] is not terminated
  cifs: Allow LANMAN auth method for servers supporting unencapsulated authentication methods
  cifs: Fix inability to write files >2GB to SMB2/3 shares
  cifs: Avoid umount hangs with smb2 when server is unresponsive
  do not treat non-symlink reparse points as valid symlinks

It's consistent with all the other spi drivers that way.
Signed-off-by: Trent Piepho <tpiepho@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>

mxs_spi_setup_transfer() would set the SSP SCK rate every time it was
called, which is before every transfer.  It is uncommon for the SCK rate to
change between transfers (or at all of that matter) and this causes many
unnecessary reprogrammings of the clock registers.

Code changed to only set the rate when it changes.  This significantly
speeds up short SPI messages, especially messages made up of many transfers,
as the calculation of the clock divisors is rather costly.  On an iMX287,
using spidev with messages that consist of 511 transfers of 4 bytes each at
an SCK of 48 MHz, the effective transfer rate more than doubles from about
290 KB/sec to 600 KB/sec!
Signed-off-by: Trent Piepho <tpiepho@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>

It can't be called with a NULL transfer anymore so it can be simplified
to not check for that.

Fix indention of line-wrapped code to Linux standard.

The transfer pointer can be const.

It's not necessary to check if the spi_transfer's speed_hz is zero, as
the spi core also fills it in from the spi_device.  However, the spi
core does not check if spi_device's speed is zero so we have to do
that still.
Signed-off-by: Trent Piepho <tpiepho@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>

The spi core already checks for a slave setting mode bits that we
didn't list as supported when the master was registered.  There is no
need to do it again in the master driver.
Signed-off-by: Trent Piepho <tpiepho@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>

Despite many warnings in the SPI documentation and code, the spi-mxs
driver sets shared chip registers in the ->setup method.  This method can
be called when transfers are in progress on other slaves controlled by the
master.  Setting registers or any other shared state will corrupt those
transfers.

So fix mxs_spi_setup() to not call mxs_spi_setup_transfer().
mxs_spi_setup_transfer() is already called for each transfer when they
are actually performed in mxs_spi_transfer_one(), so the call in
mxs_spi_setup() isn't necessary to setup anything.
Signed-off-by: Trent Piepho <tpiepho@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>

The ssp struct has a clock rate field, to provide the actual value, in Hz,
of the SSP output clock (the rate of SSP_SCK) after mxs_ssp_set_clk_rate()
is called.  It is set by mxs_ssp_set_clk_rate(), for SSP using drivers (like
SPI and MMC) to *read* if they want to know the actual clock rate.  The SPI
driver isn't supposed to *write* to it.

For some reason the spi-mxs driver decides to write to this field on init,
and sets it to the value of the SSP input clock (clk_sspN, from the MXS
clocking block) in kHz.  It shouldn't be setting the value, and certainly
shouldn't be setting it with the wrong clock in the wrong units.
Signed-off-by: Trent Piepho <tpiepho@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>

Because the driver sets the SPI_MASTER_HALF_DUPLEX flag, the spi core
will check transfers to insure they are not full duplex.  It's not
necessary to check that in the spi-mxs driver as well.
Signed-off-by: Trent Piepho <tpiepho@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>