Skiboot used to set the default Tunnel BAR register value when capi
mode was enabled. This approach was ok for the cxl driver, but
prevented other drivers from choosing different values.

Skiboot versions > 5.11 will not set the default value any longer.
This patch modifies the cxl driver to set/reset the Tunnel BAR
register when entering/exiting the cxl mode, with
pnv_pci_set_tunnel_bar().

That should work with old skiboot (since we are re-writing the value
already set) and new skiboot.

mpe: The tunnel support was only merged into Linux recently, in commit
d6a90bb8 ("powerpc/powernv: Enable tunneled operations")
(v4.17-rc1), so with new skiboot kernels between that commit and this
will not work correctly.

Fixes: d6a90bb8 ("powerpc/powernv: Enable tunneled operations")
Signed-off-by: Philippe Bergheaud <felix@linux.ibm.com>
Reviewed-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The build is failing with CONFIG_NUMA=n and some compiler versions:

  arch/powerpc/platforms/pseries/hotplug-cpu.o: In function `dlpar_online_cpu':
  hotplug-cpu.c:(.text+0x12c): undefined reference to `timed_topology_update'
  arch/powerpc/platforms/pseries/hotplug-cpu.o: In function `dlpar_cpu_remove':
  hotplug-cpu.c:(.text+0x400): undefined reference to `timed_topology_update'

Fix it by moving the empty version of timed_topology_update() into the
existing #ifdef block, which has the right guard of SPLPAR && NUMA.

Fixes: cee5405d ("powerpc/hotplug: Improve responsiveness of hotplug change")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Some syscall entry functions on powerpc are prefixed with
ppc_/ppc32_/ppc64_ rather than the usual sys_/__se_sys prefix. fork(),
clone(), swapcontext() are some examples of syscalls with such entry
points. We need to match against these names when initializing ftrace
syscall tracing.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

On powerpc64 ABIv1, we are enabling syscall tracing for only ~20
syscalls. This is due to commit e145242e ("syscalls/core,
syscalls/x86: Clean up syscall stub naming convention") which has
changed the syscall entry wrapper prefix from "SyS" to "__se_sys".

Update the logic for ABIv1 to not just skip the initial dot, but also
the "__se_sys" prefix.

Fixes: commit e145242e ("syscalls/core, syscalls/x86: Clean up syscall stub naming convention")
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

In commit 4e26bc4a ("powerpc/64: Rename soft_enabled to
irq_soft_mask") we renamed paca->soft_enabled. But then in commit
8e0b634b ("powerpc/64s: Do not allocate lppaca if we are not
virtualized") we added it back. Oops. This happened because the two
patches were in flight at the same time and rebased vs each other
multiple times, and we missed it in review.

Fixes: 8e0b634b ("powerpc/64s: Do not allocate lppaca if we are not virtualized")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Add missing "altivec unavailable" interrupt injection helper
thus fixing the linker error below:

  arch/powerpc/kvm/emulate_loadstore.o: In function `kvmppc_check_altivec_disabled':
  arch/powerpc/kvm/emulate_loadstore.c: undefined reference to `.kvmppc_core_queue_vec_unavail'

Fixes: 09f98496 ("KVM: PPC: Book3S: Add MMIO emulation for VMX instructions")
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

smp_send_stop can lock up the IPI path for any subsequent calls,
because the receiving CPUs spin in their handler function. This
started becoming a problem with the addition of an smp_send_stop
call in the reboot path, because panics can reboot after doing
their own smp_send_stop.

The NMI IPI variant was fixed with ac61c115 ("powerpc: Fix
smp_send_stop NMI IPI handling"), which leaves the smp_call_function
variant.

This is fixed by having smp_send_stop only ever do the
smp_call_function once. This is a bit less robust than the NMI IPI
fix, because any other call to smp_call_function after smp_send_stop
could deadlock, but that has always been the case, and it was not
been a problem before.

Fixes: f2748bdf ("powerpc/powernv: Always stop secondaries before reboot/shutdown")
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

gpstate_timer_handler() uses synchronous smp_call to set the pstate
on the requested core. This causes the below hard lockup:

  smp_call_function_single+0x110/0x180 (unreliable)
  smp_call_function_any+0x180/0x250
  gpstate_timer_handler+0x1e8/0x580
  call_timer_fn+0x50/0x1c0
  expire_timers+0x138/0x1f0
  run_timer_softirq+0x1e8/0x270
  __do_softirq+0x158/0x3e4
  irq_exit+0xe8/0x120
  timer_interrupt+0x9c/0xe0
  decrementer_common+0x114/0x120
  -- interrupt: 901 at doorbell_global_ipi+0x34/0x50
  LR = arch_send_call_function_ipi_mask+0x120/0x130
  arch_send_call_function_ipi_mask+0x4c/0x130
  smp_call_function_many+0x340/0x450
  pmdp_invalidate+0x98/0xe0
  change_huge_pmd+0xe0/0x270
  change_protection_range+0xb88/0xe40
  mprotect_fixup+0x140/0x340
  SyS_mprotect+0x1b4/0x350
  system_call+0x58/0x6c

One way to avoid this is removing the smp-call. We can ensure that the
timer always runs on one of the policy-cpus. If the timer gets
migrated to a cpu outside the policy then re-queue it back on the
policy->cpus. This way we can get rid of the smp-call which was being
used to set the pstate on the policy->cpus.

Fixes: 7bc54b65 ("timers, cpufreq/powernv: Initialize the gpstate timer as pinned")
Cc: stable@vger.kernel.org # v4.8+
Reported-by: Nicholas Piggin <npiggin@gmail.com>
Reported-by: Pridhiviraj Paidipeddi <ppaidipe@linux.vnet.ibm.com>
Signed-off-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
Acked-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The NMI IPI handler for a receiving CPU increments nmi_ipi_busy_count
over the handler function call, which causes later smp_send_nmi_ipi()
callers to spin until the call is finished.

The stop_this_cpu() function never returns, so the busy count is never
decremeted, which can cause the system to hang in some cases. For
example panic() will call smp_send_stop() early on which calls
stop_this_cpu() on other CPUs, then later in the reboot path,
pnv_restart() will call smp_send_stop() again, which hangs.

Fix this by adding a special case to the stop_this_cpu() handler to
decrement the busy count, because it will never return.

Now that the NMI/non-NMI versions of stop_this_cpu() are different,
split them out into separate functions rather than doing #ifdef tricks
to share the body between the two functions.

Fixes: 6bed3237 ("powerpc: use NMI IPI for smp_send_stop")
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Split out the functions, tweak change log a bit]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The OPAL RTC driver does not sleep in case it gets OPAL_BUSY or
OPAL_BUSY_EVENT from firmware, which causes large scheduling
latencies, up to 50 seconds have been observed here when RTC stops
responding (BMC reboot can do it).

Fix this by converting it to the standard form OPAL_BUSY loop that
sleeps.

Fixes: 628daa8d ("powerpc/powernv: Add RTC and NVRAM support plus RTAS fallbacks")
Cc: stable@vger.kernel.org # v3.2+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The current code extracts the physical address for UE errors and then
hooks it up into memory failure infrastructure. On successful
extraction of physical address it wrongly sets "handled = 1" which
means this UE error has been recovered. Since MCE handler gets return
value as handled = 1, it assumes that error has been recovered and
goes back to same NIP. This causes MCE interrupt again and again in a
loop leading to hard lockup.

Also, initialize phys_addr to ULONG_MAX so that we don't end up
queuing undesired page to hwpoison.

Without this patch we see:
  Severe Machine check interrupt [Recovered]
    NIP: [000000001002588c] PID: 7109 Comm: find
    Initiator: CPU
    Error type: UE [Load/Store]
      Effective address: 00007fffd2755940
      Physical address:  000020181a080000
  ...
  Severe Machine check interrupt [Recovered]
    NIP: [000000001002588c] PID: 7109 Comm: find
    Initiator: CPU
    Error type: UE [Load/Store]
      Effective address: 00007fffd2755940
      Physical address:  000020181a080000
  Severe Machine check interrupt [Recovered]
    NIP: [000000001002588c] PID: 7109 Comm: find
    Initiator: CPU
    Error type: UE [Load/Store]
      Effective address: 00007fffd2755940
      Physical address:  000020181a080000
  Memory failure: 0x20181a08: recovery action for dirty LRU page: Recovered
  Memory failure: 0x20181a08: already hardware poisoned
  Memory failure: 0x20181a08: already hardware poisoned
  Memory failure: 0x20181a08: already hardware poisoned
  Memory failure: 0x20181a08: already hardware poisoned
  Memory failure: 0x20181a08: already hardware poisoned
  Memory failure: 0x20181a08: already hardware poisoned
  ...
  Watchdog CPU:38 Hard LOCKUP

After this patch we see:

  Severe Machine check interrupt [Not recovered]
    NIP: [00007fffaae585f4] PID: 7168 Comm: find
    Initiator: CPU
    Error type: UE [Load/Store]
      Effective address: 00007fffaafe28ac
      Physical address:  00002017c0bd0000
  find[7168]: unhandled signal 7 at 00007fffaae585f4 nip 00007fffaae585f4 lr 00007fffaae585e0 code 4
  Memory failure: 0x2017c0bd: recovery action for dirty LRU page: Recovered

Fixes: 01eaac2b ("powerpc/mce: Hookup ierror (instruction) UE errors")
Fixes: ba41e1e1 ("powerpc/mce: Hookup derror (load/store) UE errors")
Cc: stable@vger.kernel.org # v4.15+
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The NPU has a limited number of address translation shootdown (ATSD)
registers and the GPU has limited bandwidth to process ATSDs. This can
result in contention of ATSD registers leading to soft lockups on some
threads, particularly when invalidating a large address range in
pnv_npu2_mn_invalidate_range().

At some threshold it becomes more efficient to flush the entire GPU
TLB for the given MM context (PID) than individually flushing each
address in the range. This patch will result in ranges greater than
2MB being converted from 32+ ATSDs into a single ATSD which will flush
the TLB for the given PID on each GPU.

Fixes: 1ab66d1f ("powerpc/powernv: Introduce address translation services for Nvlink2")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Tested-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

There is a single npu context per set of callback parameters. Callers
should be prevented from overwriting existing callback values so
instead return an error if different parameters are passed.

Fixes: 1ab66d1f ("powerpc/powernv: Introduce address translation services for Nvlink2")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Reviewed-by: Mark Hairgrove <mhairgrove@nvidia.com>
Tested-by: Mark Hairgrove <mhairgrove@nvidia.com>
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The pnv_npu2_init_context() and pnv_npu2_destroy_context() functions
are used to allocate/free contexts to allow address translation and
shootdown by the NPU on a particular GPU. Context initialisation is
implicitly safe as it is protected by the requirement mmap_sem be held
in write mode, however pnv_npu2_destroy_context() does not require
mmap_sem to be held and it is not safe to call with a concurrent
initialisation for a different GPU.

It was assumed the driver would ensure destruction was not called
concurrently with initialisation. However the driver may be simplified
by allowing concurrent initialisation and destruction for different
GPUs. As npu context creation/destruction is not a performance
critical path and the critical section is not large a single spinlock
is used for simplicity.

Fixes: 1ab66d1f ("powerpc/powernv: Introduce address translation services for Nvlink2")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Reviewed-by: Mark Hairgrove <mhairgrove@nvidia.com>
Tested-by: Mark Hairgrove <mhairgrove@nvidia.com>
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Don't do this via custom code, instead now that we have support in the
arch hotplug/hotunplug code, rely on those routines to do the right
thing.

The existing flush doesn't work because it uses ppc64_caches.l1d.size
instead of ppc64_caches.l1d.line_size.

Fixes: 9d5171a8 ("powerpc/powernv: Enable removal of memory for in memory tracing")
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
Reviewed-by: Rashmica Gupta <rashmica.g@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

This patch adds support for flushing potentially dirty cache lines
when memory is hot-plugged/hot-un-plugged. The support is currently
limited to 64 bit systems.

The bug was exposed when mappings for a device were actually
hot-unplugged and plugged in back later. A similar issue was observed
during the development of memtrace, but memtrace does it's own
flushing of region via a custom routine.

These patches do a flush both on hotplug/unplug to clear any stale
data in the cache w.r.t mappings, there is a small race window where a
clean cache line may be created again just prior to tearing down the
mapping.

The patches were tested by disabling the flush routines in memtrace
and doing I/O on the trace file. The system immediately
checkstops (quite reliablly if prior to the hot-unplug of the memtrace
region, we memset the regions we are about to hot unplug). After these
patches no custom flushing is needed in the memtrace code.

Fixes: 9d5171a8 ("powerpc/powernv: Enable removal of memory for in memory tracing")
Cc: stable@vger.kernel.org # v4.14+
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
Acked-by: Reza Arbab <arbab@linux.ibm.com>
Reviewed-by: Rashmica Gupta <rashmica.g@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Pull drm fixes from Dave Airlie:
 "Exynos, i915, vc4, amdgpu fixes.

  i915:
   - an oops fix
   - two race fixes
   - some gvt fixes

  amdgpu:
   - dark screen fix
   - clk/voltage fix
   - vega12 smu fix

  vc4:
   - memory leak fix

  exynos just drops some code"

* tag 'drm-fixes-for-v4.17-rc2' of git://people.freedesktop.org/~airlied/linux: (23 commits)
  drm/amd/powerplay: header file interface to SMU update
  drm/amd/pp: Fix bug voltage can't be OD separately on VI
  drm/amd/display: Don't program bypass on linear regamma LUT
  drm/i915: Fix LSPCON TMDS output buffer enabling from low-power state
  drm/i915/audio: Fix audio detection issue on GLK
  drm/i915: Call i915_perf_fini() on init_hw error unwind
  drm/i915/bios: filter out invalid DDC pins from VBT child devices
  drm/i915/pmu: Inspect runtime PM state more carefully while estimating RC6
  drm/i915: Do no use kfree() to free a kmem_cache_alloc() return value
  drm/exynos: exynos_drm_fb -> drm_framebuffer
  drm/exynos: Move dma_addr out of exynos_drm_fb
  drm/exynos: Move GEM BOs to drm_framebuffer
  drm: Fix HDCP downstream dev count read
  drm/vc4: Fix memory leak during BO teardown
  drm/i915/execlists: Clear user-active flag on preemption completion
  drm/i915/gvt: Add drm_format_mod update
  drm/i915/gvt: Disable primary/sprite/cursor plane at virtual display initialization
  drm/i915/gvt: Delete redundant error message in fb_decode.c
  drm/i915/gvt: Cancel dma map when resetting ggtt entries
  drm/i915/gvt: Missed to cancel dma map for ggtt entries
  ...

- Fix a dark screen issue in DC
- Fix clk/voltage dependency tracking for wattman
- Update SMU interface for vega12

* 'drm-next-4.17' of git://people.freedesktop.org/~agd5f/linux:
  drm/amd/powerplay: header file interface to SMU update
  drm/amd/pp: Fix bug voltage can't be OD separately on VI
  drm/amd/display: Don't program bypass on linear regamma LUT

Merge tag 'exynos-drm-fixes-for-v4.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-next

Remove Exynos specific framebuffer structure and
relevant functions.
- it removes exynos_drm_fb structure which is a wrapper of
  drm_framebuffer and unnecessary two exynos specific callback
  functions, exynos_drm_destory() and exynos_drm_fb_create_handle()
  because we can reuse existing drm common callback ones instead.

* tag 'exynos-drm-fixes-for-v4.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
  drm/exynos: exynos_drm_fb -> drm_framebuffer
  drm/exynos: Move dma_addr out of exynos_drm_fb
  drm/exynos: Move GEM BOs to drm_framebuffer
  drm/amdkfd: Deallocate SDMA queues correctly
  drm/amdkfd: Fix scratch memory with HWS enabled

Merge tag 'drm-intel-next-fixes-2018-04-19' of git://anongit.freedesktop.org/drm/drm-intel into drm-next

- Fix for FDO #105549: Avoid OOPS on bad VBT (Jani)
- Fix rare pre-emption race (Chris)
- Fix RC6 race against PM transitions (Tvrtko)

* tag 'drm-intel-next-fixes-2018-04-19' of git://anongit.freedesktop.org/drm/drm-intel:
  drm/i915/audio: Fix audio detection issue on GLK
  drm/i915: Call i915_perf_fini() on init_hw error unwind
  drm/i915/bios: filter out invalid DDC pins from VBT child devices
  drm/i915/pmu: Inspect runtime PM state more carefully while estimating RC6
  drm/i915: Do no use kfree() to free a kmem_cache_alloc() return value
  drm/i915/execlists: Clear user-active flag on preemption completion
  drm/i915/gvt: Add drm_format_mod update
  drm/i915/gvt: Disable primary/sprite/cursor plane at virtual display initialization
  drm/i915/gvt: Delete redundant error message in fb_decode.c
  drm/i915/gvt: Cancel dma map when resetting ggtt entries
  drm/i915/gvt: Missed to cancel dma map for ggtt entries
  drm/i915/gvt: Make MI_USER_INTERRUPT nop in cmd parser
  drm/i915/gvt: Mark expected switch fall-through in handle_g2v_notification
  drm/i915/gvt: throw error on unhandled vfio ioctls

drm-misc-fixes:

stable: vc4: Fix memory leak during BO teardown (Daniel)
dp: Add i2c retry for LSPCON adapters (Imre)
hdcp: Fix device count mask (Ramalingam)

Cc: Daniel J Blueman <daniel@quora.org
Cc: Imre Deak <imre.deak@intel.com>
Cc: Ramalingam C <ramalingam.c@intel.com>

* tag 'drm-misc-fixes-2018-04-18-1' of git://anongit.freedesktop.org/drm/drm-misc:
  drm/i915: Fix LSPCON TMDS output buffer enabling from low-power state
  drm: Fix HDCP downstream dev count read
  drm/vc4: Fix memory leak during BO teardown

Pull cifs fixes from Steve French:
 "Various SMB3/CIFS fixes.

  There are three more security related fixes in progress that are not
  included in this set but they are still being tested and reviewed, so
  sending this unrelated set of smaller fixes now"

* tag '4.17-rc1-SMB3-CIFS' of git://git.samba.org/sfrench/cifs-2.6:
  CIFS: fix typo in cifs_dbg
  cifs: do not allow creating sockets except with SMB1 posix exensions
  cifs: smbd: Dump SMB packet when configured
  cifs: smbd: Check for iov length on sending the last iov
  fs: cifs: Adding new return type vm_fault_t
  cifs: smb2ops: Fix NULL check in smb2_query_symlink

Pull btrfs fixes from David Sterba:
 "This contains a few fixups to the qgroup patches that were merged this
  dev cycle, unaligned access fix, blockgroup removal corner case fix
  and a small debugging output tweak"

* tag 'for-4.17-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  btrfs: print-tree: debugging output enhancement
  btrfs: Fix race condition between delayed refs and blockgroup removal
  btrfs: fix unaligned access in readdir
  btrfs: Fix wrong btrfs_delalloc_release_extents parameter
  btrfs: delayed-inode: Remove wrong qgroup meta reservation calls
  btrfs: qgroup: Use independent and accurate per inode qgroup rsv
  btrfs: qgroup: Commit transaction in advance to reduce early EDQUOT

Pull x86 fixes from Thomas Gleixner:
 "A small set of fixes for x86:

   - Prevent X2APIC ID 0xFFFFFFFF from being treated as valid, which
     causes the possible CPU count to be wrong.

   - Prevent 32bit truncation in calc_hpet_ref() which causes the TSC
     calibration to fail

   - Fix the page table setup for temporary text mappings in the resume
     code which causes resume failures

   - Make the page table dump code handle HIGHPTE correctly instead of
     oopsing

   - Support for topologies where NUMA nodes share an LLC to prevent a
     invalid topology warning and further malfunction on such systems.

   - Remove the now unused pci-nommu code

   - Remove stale function declarations"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/power/64: Fix page-table setup for temporary text mapping
  x86/mm: Prevent kernel Oops in PTDUMP code with HIGHPTE=y
  x86,sched: Allow topologies where NUMA nodes share an LLC
  x86/processor: Remove two unused function declarations
  x86/acpi: Prevent X2APIC id 0xffffffff from being accounted
  x86/tsc: Prevent 32bit truncation in calc_hpet_ref()
  x86: Remove pci-nommu.c

Pull timer fixes from Thomas Gleixner:
 "A small set of timer fixes:

   - Evaluate the -ETIME condition correctly in the imx tpm driver

   - Fix the evaluation order of a condition in posix cpu timers

   - Use pr_cont() in the clockevents code to prevent ugly message
     splitting

   - Remove __current_kernel_time() which is now unused to prevent that
     new users show up.

   - Remove a stale forward declaration"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  clocksource/imx-tpm: Correct -ETIME return condition check
  posix-cpu-timers: Ensure set_process_cpu_timer is always evaluated
  timekeeping: Remove __current_kernel_time()
  timers: Remove stale struct tvec_base forward declaration
  clockevents: Fix kernel messages split across multiple lines

Pull perf fixes from Thomas Gleixner:
 "A larger set of updates for perf.

  Kernel:

   - Handle the SBOX uncore monitoring correctly on Broadwell CPUs which
     do not have SBOX.

   - Store context switch out type in PERF_RECORD_SWITCH[_CPU_WIDE]. The
     percentage of preempting and non-preempting context switches help
     understanding the nature of workloads (CPU or IO bound) that are
     running on a machine. This adds the kernel facility and userspace
     changes needed to show this information in 'perf script' and 'perf
     report -D' (Alexey Budankov)

   - Remove a WARN_ON() in the trace/kprobes code which is pointless
     because the return error code is already telling the caller what's
     wrong.

   - Revert a fugly workaround for clang BPF targets.

   - Fix sample_max_stack maximum check and do not proceed when an error
     has been detect, return them to avoid misidentifying errors (Jiri
     Olsa)

   - Add SPDX idenitifiers and get rid of GPL boilderplate.

  Tools:

   - Synchronize kernel ABI headers, v4.17-rc1 (Ingo Molnar)

   - Support MAP_FIXED_NOREPLACE, noticed when updating the
     tools/include/ copies (Arnaldo Carvalho de Melo)

   - Add '\n' at the end of parse-options error messages (Ravi Bangoria)

   - Add s390 support for detailed/verbose PMU event description (Thomas
     Richter)

   - perf annotate fixes and improvements:

      * Allow showing offsets in more than just jump targets, use the
        new 'O' hotkey in the TUI, config ~/.perfconfig
        annotate.offset_level for it and for --stdio2 (Arnaldo Carvalho
        de Melo)

      * Use the resolved variable names from objdump disassembled lines
        to make them more compact, just like was already done for some
        instructions, like "mov", this eventually will be done more
        generally, but lets now add some more to the existing mechanism
        (Arnaldo Carvalho de Melo)

   - perf record fixes:

      * Change warning for missing topology sysfs entry to debug, as not
        all architectures have those files, s390 being one of those
        (Thomas Richter)

      * Remove old error messages about things that unlikely to be the
        root cause in modern systems (Andi Kleen)

   - perf sched fixes:

      * Fix -g/--call-graph documentation (Takuya Yamamoto)

   - perf stat:

      * Enable 1ms interval for printing event counters values in
        (Alexey Budankov)

   - perf test fixes:

      * Run dwarf unwind on arm32 (Kim Phillips)

      * Remove unused ptrace.h include from LLVM test, sidesteping older
        clang's lack of support for some asm constructs (Arnaldo
        Carvalho de Melo)

      * Fixup BPF test using epoll_pwait syscall function probe, to cope
        with the syscall routines renames performed in this development
        cycle (Arnaldo Carvalho de Melo)

   - perf version fixes:

      * Do not print info about HAVE_LIBAUDIT_SUPPORT in 'perf version
        --build-options' when HAVE_SYSCALL_TABLE_SUPPORT is true, as
        libaudit won't be used in that case, print info about
        syscall_table support instead (Jin Yao)

   - Build system fixes:

      * Use HAVE_..._SUPPORT used consistently (Jin Yao)

      * Restore READ_ONCE() C++ compatibility in tools/include (Mark
        Rutland)

      * Give hints about package names needed to build jvmti (Arnaldo
        Carvalho de Melo)"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (37 commits)
  perf/x86/intel/uncore: Fix SBOX support for Broadwell CPUs
  perf/x86/intel/uncore: Revert "Remove SBOX support for Broadwell server"
  coresight: Move to SPDX identifier
  perf test BPF: Fixup BPF test using epoll_pwait syscall function probe
  perf tests mmap: Show which tracepoint is failing
  perf tools: Add '\n' at the end of parse-options error messages
  perf record: Remove suggestion to enable APIC
  perf record: Remove misleading error suggestion
  perf hists browser: Clarify top/report browser help
  perf mem: Allow all record/report options
  perf trace: Support MAP_FIXED_NOREPLACE
  perf: Remove superfluous allocation error check
  perf: Fix sample_max_stack maximum check
  perf: Return proper values for user stack errors
  perf list: Add s390 support for detailed/verbose PMU event description
  perf script: Extend misc field decoding with switch out event type
  perf report: Extend raw dump (-D) out with switch out event type
  perf/core: Store context switch out type in PERF_RECORD_SWITCH[_CPU_WIDE]
  tools/headers: Synchronize kernel ABI headers, v4.17-rc1
  trace_kprobe: Remove warning message "Could not insert probe at..."
  ...

Pull objtool fix from Thomas Gleixner:
 "A single fix for objtool so it uses the host C and LD flags and not
  the target ones"

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  objtool: Support HOSTCFLAGS and HOSTLDFLAGS

Pull /dev/random fixes from Ted Ts'o:
 "Fix some bugs in the /dev/random driver which causes getrandom(2) to
  unblock earlier than designed.

  Thanks to Jann Horn from Google's Project Zero for pointing this out
  to me"

* tag 'random_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
  random: add new ioctl RNDRESEEDCRNG
  random: crng_reseed() should lock the crng instance that it is modifying
  random: set up the NUMA crng instances after the CRNG is fully initialized
  random: use a different mixing algorithm for add_device_randomness()
  random: fix crng_ready() test

Pull libnvdimm fixes from Dan Williams:
 "A regression fix, new unit test infrastructure and a build fix:

   - Regression fix addressing support for the new NVDIMM label storage
     area access commands (_LSI, _LSR, and _LSW).

     The Intel specific version of these commands communicated the
     "Device Locked" status on the label-storage-information command.

     However, these new commands (standardized in ACPI 6.2) communicate
     the "Device Locked" status on the label-storage-read command, and
     the driver was missing the indication.

     Reading from locked persistent memory is similar to reading
     unmapped PCI memory space, returns all 1's.

   - Unit test infrastructure is added to regression test the "Device
     Locked" detection failure.

   - A build fix is included to allow the "of_pmem" driver to be built
     as a module and translate an Open Firmware described device to its
     local numa node"

* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  MAINTAINERS: Add backup maintainers for libnvdimm and DAX
  device-dax: allow MAP_SYNC to succeed
  Revert "libnvdimm, of_pmem: workaround OF_NUMA=n build error"
  libnvdimm, of_pmem: use dev_to_node() instead of of_node_to_nid()
  tools/testing/nvdimm: enable labels for nfit_test.1 dimms
  tools/testing/nvdimm: fix missing newline in nfit_test_dimm 'handle' attribute
  tools/testing/nvdimm: support nfit_test_dimm attributes under nfit_test.1
  tools/testing/nvdimm: allow custom error code injection
  libnvdimm, dimm: handle EACCES failures from label reads

Pull sound fixes from Takashi Iwai:
 "A few small fixes:

   - a fix for the NULL-dereference in rawmidi compat ioctls, triggered
     by fuzzer

   - HD-audio Realtek codec quirks, a VIA controller fixup

   - a long-standing bug fix in LINE6 MIDI"

* tag 'sound-4.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: rawmidi: Fix missing input substream checks in compat ioctls
  ALSA: hda/realtek - adjust the location of one mic
  ALSA: hda/realtek - set PINCFG_HEADSET_MIC to parse_flags
  ALSA: hda - New VIA controller suppor no-snoop path
  ALSA: line6: Use correct endpoint type for midi output

Pull watchdog fixes from Wim Van Sebroeck:

 - fall-through fixes

 - MAINTAINER change for hpwdt

 - renesas-wdt: Add support for WDIOF_CARDRESET

 - aspeed: set bootstatus during probe

* tag 'linux-watchdog-4.17-rc2' of git://www.linux-watchdog.org/linux-watchdog:
  aspeed: watchdog: Set bootstatus during probe
  watchdog: renesas-wdt: Add support for WDIOF_CARDRESET
  watchdog: wafer5823wdt: Mark expected switch fall-through
  watchdog: w83977f_wdt: Mark expected switch fall-through
  watchdog: sch311x_wdt: Mark expected switch fall-through
  watchdog: hpwdt: change maintainer.

Merge tag 'linux-kselftest-4.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest

Pull Kselftest fix from Shuah Khan:
 "A fix from Michael Ellerman to not run dnotify_test by default to
  prevent Kselftest running forever"

* tag 'linux-kselftest-4.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
  selftests/filesystems: Don't run dnotify_test by default

Pull arm64 fixes from Catalin Marinas:

 - kasan: avoid pfn_to_nid() before the page array is initialised

 - Fix typo causing the "upgrade" of known signals to SIGKILL

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: signal: don't force known signals to SIGKILL
  arm64: kasan: avoid pfn_to_nid() before page array is initialized

Merge misc fixes from Andrew Morton:

 - "fork: unconditionally clear stack on fork" is a non-bugfix which got
   lost during the merge window - performance concerns appear to have
   been adequately addressed.

 - and a bunch of fixes

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  mm/filemap.c: fix NULL pointer in page_cache_tree_insert()
  mm: memcg: add __GFP_NOWARN in __memcg_schedule_kmem_cache_create()
  fs, elf: don't complain MAP_FIXED_NOREPLACE unless -EEXIST error
  kexec_file: do not add extra alignment to efi memmap
  proc: fix /proc/loadavg regression
  proc: revalidate kernel thread inodes to root:root
  autofs: mount point create should honour passed in mode
  MAINTAINERS: add personal addresses for Sascha and Uwe
  kasan: add no_sanitize attribute for clang builds
  rapidio: fix rio_dma_transfer error handling
  mm: enable thp migration for shmem thp
  writeback: safer lock nesting
  mm, pagemap: fix swap offset value for PMD migration entry
  mm: fix do_pages_move status handling
  fork: unconditionally clear stack on fork

Merge tag 'perf-urgent-for-mingo-4.17-20180420' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent

Pull perf/urgent fixes and improvements from Arnaldo Carvalho de Melo:

- Store context switch out type in PERF_RECORD_SWITCH[_CPU_WIDE].
  The percentage of preempting and non-preempting context switches help
  understanding the nature of workloads (CPU or IO bound) that are running
  on a machine. This adds the kernel facility and userspace changes needed
  to show this information in 'perf script' and 'perf report -D' (Alexey Budankov)

- Remove old error messages about things that unlikely to be the root cause
  in modern systems (Andi Kleen)

- Synchronize kernel ABI headers, v4.17-rc1 (Ingo Molnar)

- Support MAP_FIXED_NOREPLACE, noticed when updating the tools/include/
  copies (Arnaldo Carvalho de Melo)

- Fixup BPF test using epoll_pwait syscall function probe, to cope with
  the syscall routines renames performed in this development cycle (Arnaldo Carvalho de Melo)

- Fix sample_max_stack maximum check and do not proceed when an error
  has been detect, return them to avoid misidentifying errors (Jiri Olsa)

- Add '\n' at the end of parse-options error messages (Ravi Bangoria)

- Add s390 support for detailed/verbose PMU event description (Thomas Richter)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>

f2fs specifies the __GFP_ZERO flag for allocating some of its pages.
Unfortunately, the page cache also uses the mapping's GFP flags for
allocating radix tree nodes.  It always masked off the __GFP_HIGHMEM
flag, and masks off __GFP_ZERO in some paths, but not all.  That causes
radix tree nodes to be allocated with a NULL list_head, which causes
backtraces like:

  __list_del_entry+0x30/0xd0
  list_lru_del+0xac/0x1ac
  page_cache_tree_insert+0xd8/0x110

The __GFP_DMA and __GFP_DMA32 flags would also be able to sneak through
if they are ever used.  Fix them all by using GFP_RECLAIM_MASK at the
innermost location, and remove it from earlier in the callchain.

Link: http://lkml.kernel.org/r/20180411060320.14458-2-willy@infradead.org
Fixes: 449dd698 ("mm: keep page cache radix tree nodes in check")
Signed-off-by: Matthew Wilcox <mawilcox@microsoft.com>
Reported-by: Chris Fries <cfries@google.com>
Debugged-by: Minchan Kim <minchan@kernel.org>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

If there is heavy memory pressure, page allocation with __GFP_NOWAIT
fails easily although it's order-0 request.  I got below warning 9 times
for normal boot.

     <snip >: page allocation failure: order:0, mode:0x2200000(GFP_NOWAIT|__GFP_NOTRACK)
     .. snip ..
     Call trace:
       dump_backtrace+0x0/0x4
       dump_stack+0xa4/0xc0
       warn_alloc+0xd4/0x15c
       __alloc_pages_nodemask+0xf88/0x10fc
       alloc_slab_page+0x40/0x18c
       new_slab+0x2b8/0x2e0
       ___slab_alloc+0x25c/0x464
       __kmalloc+0x394/0x498
       memcg_kmem_get_cache+0x114/0x2b8
       kmem_cache_alloc+0x98/0x3e8
       mmap_region+0x3bc/0x8c0
       do_mmap+0x40c/0x43c
       vm_mmap_pgoff+0x15c/0x1e4
       sys_mmap+0xb0/0xc8
       el0_svc_naked+0x24/0x28
     Mem-Info:
     active_anon:17124 inactive_anon:193 isolated_anon:0
      active_file:7898 inactive_file:712955 isolated_file:55
      unevictable:0 dirty:27 writeback:18 unstable:0
      slab_reclaimable:12250 slab_unreclaimable:23334
      mapped:19310 shmem:212 pagetables:816 bounce:0
      free:36561 free_pcp:1205 free_cma:35615
     Node 0 active_anon:68496kB inactive_anon:772kB active_file:31592kB inactive_file:2851820kB unevictable:0kB isolated(anon):0kB isolated(file):220kB mapped:77240kB dirty:108kB writeback:72kB shmem:848kB writeback_tmp:0kB unstable:0kB all_unreclaimable? no
     DMA free:142188kB min:3056kB low:3820kB high:4584kB active_anon:10052kB inactive_anon:12kB active_file:312kB inactive_file:1412620kB unevictable:0kB writepending:0kB present:1781412kB managed:1604728kB mlocked:0kB slab_reclaimable:3592kB slab_unreclaimable:876kB kernel_stack:400kB pagetables:52kB bounce:0kB free_pcp:1436kB local_pcp:124kB free_cma:142492kB
     lowmem_reserve[]: 0 1842 1842
     Normal free:4056kB min:4172kB low:5212kB high:6252kB active_anon:58376kB inactive_anon:760kB active_file:31348kB inactive_file:1439040kB unevictable:0kB writepending:180kB present:2000636kB managed:1923688kB mlocked:0kB slab_reclaimable:45408kB slab_unreclaimable:92460kB kernel_stack:9680kB pagetables:3212kB bounce:0kB free_pcp:3392kB local_pcp:688kB free_cma:0kB
     lowmem_reserve[]: 0 0 0
     DMA: 0*4kB 0*8kB 1*16kB (C) 0*32kB 0*64kB 0*128kB 1*256kB (C) 1*512kB (C) 0*1024kB 1*2048kB (C) 34*4096kB (C) = 142096kB
     Normal: 228*4kB (UMEH) 172*8kB (UMH) 23*16kB (UH) 24*32kB (H) 5*64kB (H) 1*128kB (H) 0*256kB 0*512kB 0*1024kB 0*2048kB 0*4096kB = 3872kB
     721350 total pagecache pages
     0 pages in swap cache
     Swap cache stats: add 0, delete 0, find 0/0
     Free swap  = 0kB
     Total swap = 0kB
     945512 pages RAM
     0 pages HighMem/MovableOnly
     63408 pages reserved
     51200 pages cma reserved

__memcg_schedule_kmem_cache_create() tries to create a shadow slab cache
and the worker allocation failure is not really critical because we will
retry on the next kmem charge.  We might miss some charges but that
shouldn't be critical.  The excessive allocation failure report is not
very helpful.

[mhocko@kernel.org: changelog update]
Link: http://lkml.kernel.org/r/20180418022912.248417-1-minchan@kernel.orgSigned-off-by: Minchan Kim <minchan@kernel.org>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit 4ed28639 ("fs, elf: drop MAP_FIXED usage from elf_map") is
printing spurious messages under memory pressure due to map_addr == -ENOMEM.

 9794 (a.out): Uhuuh, elf segment at 00007f2e34738000(fffffffffffffff4) requested but the memory is mapped already
 14104 (a.out): Uhuuh, elf segment at 00007f34fd76c000(fffffffffffffff4) requested but the memory is mapped already
 16843 (a.out): Uhuuh, elf segment at 00007f930ecc7000(fffffffffffffff4) requested but the memory is mapped already

Complain only if -EEXIST, and use %px for printing the address.

Link: http://lkml.kernel.org/r/201804182307.FAC17665.SFMOFJVFtHOLOQ@I-love.SAKURA.ne.jp
Fixes: 4ed28639 ("fs, elf: drop MAP_FIXED usage from elf_map") is
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Andrei Vagin <avagin@openvz.org>
Cc: Khalid Aziz <khalid.aziz@oracle.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Kees Cook <keescook@chromium.org>
Cc: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Cc: Joel Stanley <joel@jms.id.au>
Cc: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Chun-Yi reported a kernel warning message below:

  WARNING: CPU: 0 PID: 0 at ../mm/early_ioremap.c:182 early_iounmap+0x4f/0x12c()
  early_iounmap(ffffffffff200180, 00000118) [0] size not consistent 00000120

The problem is x86 kexec_file_load adds extra alignment to the efi
memmap: in bzImage64_load():

        efi_map_sz = efi_get_runtime_map_size();
        efi_map_sz = ALIGN(efi_map_sz, 16);

And __efi_memmap_init maps with the size including the alignment bytes
but efi_memmap_unmap use nr_maps * desc_size which does not include the
extra bytes.

The alignment in kexec code is only needed for the kexec buffer internal
use Actually kexec should pass exact size of the efi memmap to 2nd
kernel.

Link: http://lkml.kernel.org/r/20180417083600.GA1972@dhcp-128-65.nay.redhat.comSigned-off-by: Dave Young <dyoung@redhat.com>
Reported-by: joeyli <jlee@suse.com>
Tested-by: Randy Wright <rwright@hpe.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>