[ Upstream commit 22bba805 ]

The Broadcom controller on aries S5PV210 boards sends out a couple of
unknown packets after the firmware is loaded.  This will cause
logging of errors such as:
	Bluetooth: hci0: Frame reassembly failed (-84)

This is probably also the case with other boards, as there are related
Android userspace patches for custom ROMs such as
https://review.lineageos.org/#/c/LineageOS/android_system_bt/+/142721/
Since this appears to be intended behaviour, treated them as diagnostic
packets.

Note that this is another variant of commit 01d5e44a
("Bluetooth: hci_bcm: Handle empty packet after firmware loading")
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 966e927b ]

If palmas_smps_read() fails, we should not use the read data in "reg"
which may contain random value. The fix inserts a check for the return
value of palmas_smps_read(): If it fails, we return the error code
upstream and stop using "reg".
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 32c8c4c6 ]

mfsrin() takes segment num from bits 31-28 (IBM bits 0-3).
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[mpe: Clarify bit numbering]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit e93ba1b7 ]

This patch fixes the loop in p_block_mapped() and v_block_mapped()
to scan the entire bat_addrs[] array.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 6db92468 ]

When a failure occurs in rtnl_configure_link(), the current code
calls unregister_netdevice() to roll back the earlier call to
register_netdevice(), and jumps to errout, which calls
vxlan_fdb_destroy().

However unregister_netdevice() calls transitively ndo_uninit, which is
vxlan_uninit(), and that already takes care of deleting the default FDB
entry by calling vxlan_fdb_delete_default(). Since the entry added
earlier in __vxlan_dev_create() is exactly the default entry, the
cleanup code in the errout block always leads to double free and thus a
panic.

Besides, since vxlan_fdb_delete_default() always destroys the FDB entry
with notification enabled, the deletion of the default entry is notified
even before the addition was notified.

Instead, move the unregister_netdevice() call after the manual destroy,
which solves both problems.

Fixes: 0241b836 ("vxlan: fix default fdb entry netlink notify ordering during netdev create")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 86fe57fc ]

TIMER_INTR_MASK register (Base Address of Timer + 0x38) is not designed
for masking interrupts on ast2500 chips, and it's not even listed in
ast2400 datasheet, so it's not safe to access TIMER_INTR_MASK on aspeed
chips.

Similarly, TIMER_INTR_STATE register (Base Address of Timer + 0x34) is
not interrupt status register on ast2400 and ast2500 chips. Although
there is no side effect to reset the register in fttmr010_common_init(),
it's just misleading to do so.

Besides, "count_down" is renamed to "is_aspeed" in "fttmr010" structure,
and more comments are added so the code is more readble.
Signed-off-by: Tao Ren <taoren@fb.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 5050ae5f ]

We accidentally return success on this error path.

Fixes: f931551b ("IB/qib: Add new qib driver for QLogic PCIe InfiniBand adapters")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 7ca860e3 ]

The bulkstat family of ioctls are problematic on x32, because there is
a mixup of native 32-bit and 64-bit conventions.  The xfs_fsop_bulkreq
struct contains pointers and 32-bit integers so that matches the native
32-bit layout, and that means the ioctl implementation goes into the
regular compat path on x32.

However, the 'ubuffer' member of that struct in turn refers to either
struct xfs_inogrp or xfs_bstat (or an array of these).  On x32, those
structures match the native 64-bit layout.  The compat implementation
writes out the 32-bit version of these structures.  This is not the
expected format for x32 userspace, causing problems.

Fortunately the functions which actually output these xfs_inogrp and
xfs_bstat structures have an easy way to select which output format
is required, so we just need a little tweak to select the right format
on x32.
Signed-off-by: Nick Bowler <nbowler@draconx.ca>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit c456d644 ]

While inspecting the ioctl implementations, I noticed that the compat
implementation of XFS_IOC_ATTRLIST_BY_HANDLE does not do exactly the
same thing as the native implementation.  Specifically, the "cursor"
does not appear to be written out to userspace on the compat path,
like it is on the native path.

This adjusts the compat implementation to copy out the cursor just
like the native implementation does.  The attrlist cursor does not
require any special compat handling.  This fixes xfstests xfs/269
on both IA-32 and x32 userspace, when running on an amd64 kernel.
Signed-off-by: Nick Bowler <nbowler@draconx.ca>
Fixes: 0facef7f ("xfs: in _attrlist_by_handle, copy the cursor back to userspace")
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 74694bcb ]

Sending a check/repair message infrequently leads to -EBUSY instead of
properly identifying an active resync.  This occurs because
raid_message() is testing recovery bits in a racy way.

Fix by calling decipher_sync_action() from raid_message() to properly
identify the idle state of the RAID device.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit bc020561 ]

Before this patch, function do_grow would not reserve enough journal
blocks in the transaction to unstuff jdata files while growing them.
This patch adds the logic to add one more block if the file to grow
is jdata.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Reviewed-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit a00f5276 ]

The flakey target is documented to be able to corrupt the Nth byte in
a bio, but does not corrupt byte indices after the first biovec in the
bio. Change the corrupting function to actually corrupt the Nth byte
no matter in which biovec that index falls.

A test device generating two-page bios, atop a flakey device configured
to corrupt a byte index on the second page, verified both the failure
to corrupt before this patch and the expected corruption after this
change.
Signed-off-by: John Dorminy <jdorminy@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 46b14eef ]
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 054f2400 ]

Some values in the Peripheral Function Select Register 10 descriptor are
shifted by one position, which may cause a peripheral function to be
programmed incorrectly.

Fixing this makes all HSCIF0 pins use Function 4 (value 3), like was
already the case for the HSCK0 pin in field IP10[5:3].

Fixes: ac1ebc21 ("sh-pfc: Add sh7734 pinmux support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 1b99d0c8 ]

The Port F Control Register 3 (PFCR3) contains only a single field.
However, counting from left to right, it is the fourth field, not the
first field.
Insert the missing dummy configuration values (3 fields of 16 values) to
fix this.

The descriptor for the Port F Control Register 0 (PFCR0) lacks the
description for the 4th field (PF0 Mode, PF0MD[2:0]).
Add the missing configuration values to fix this.

Fixes: a8d42fc4 ("sh-pfc: Add sh7264 pinmux support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 755a5b80 ]

The SEL_I2C1 (MOD_SEL0[21:20]) field in Module Select Register 0 has a
width of 2 bits, i.e. it allows programming one out of 4 different
configurations.
However, the MOD_SEL0_21_20 macro contains 8 values instead of 4,
overflowing into the subsequent fields in the register, and thus breaking
the configuration of the latter.

Fix this by dropping the bogus last 4 values, including the non-existent
SEL_I2C1_4 configuration.

Fixes: 6d4036a1 ("pinctrl: sh-pfc: Initial R8A77990 PFC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 308c3e66 ]

Make sure the debug feature and its allocated resources get
released upon unsuccessful architecture initialization.

A related indication of the issue will be reported as kernel
message.
Signed-off-by: Michael Mueller <mimu@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Message-Id: <20181130143215.69496-2-mimu@linux.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 56d37462 ]

With autoneg enabled, PHY loopback test fails. To disable autoneg,
driver needs to send a valid forced speed to FW. FW is not sending
async event for invalid speeds. To fix this, query forced speeds
and send the correct speed when disabling autoneg mode.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit b8875ca3 ]

With the current driver, the statistics reported by .ndo_get_stats64()
are reset when the device goes down.  Store a snapshot of the
rtnl_link_stats64 before shutdown.  This snapshot is added to the
current counters in .ndo_get_stats64() so that the counters will not
get reset when the device is down.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 7c675421 ]

Currently firmware specific errors are returned directly in flash_device
and reset ethtool hooks. Modify it to return linux standard errors
to userspace when flashing operations fail.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 26cb5a32 ]

... and don't abuse mount_nodev(), while we are at it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Reviewed-by: David Howells <dhowells@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 82940599 ]

Each media stream negotiation between 2 SIP peers will trigger creation
of 4 different expectations (2 RTP and 2 RTCP):
 - INVITE will create expectations for the media packets sent by the
   called peer
 - reply to the INVITE will create expectations for media packets sent
   by the caller

The dport used by these expectations usually match the ones selected
by the SIP peers, but they might get translated due to conflicts with
another expectation. When such event occur, it is important to do
this translation in both directions, dport translation on the receiving
path and sport translation on the sending path.

This commit fixes the sport translation when the peer requiring it is
also the one that starts the media stream. In this scenario, first media
stream packet is forwarded from LAN to WAN and will rely on
nf_nat_sip_expected() to do the necessary sport translation. However, the
expectation matched by this packet does not contain the necessary information
for doing SNAT, this data being stored in the paired expectation created by
the sender's SIP message (INVITE or reply to it).
Signed-off-by: Alin Nastac <alin.nastac@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 199fa087 ]

The failure to create debugfs entry is unpleasant event, but not enough
to abort drier initialization. Align the mlx5_core code to debugfs design
and continue execution whenever debugfs_create_dir() successes or not.

Fixes: e126ba97 ("mlx5: Add driver for Mellanox Connect-IB adapters")
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 9b4924da ]

This patch is based on commit a86caa9b ("pinctrl: msm: fix gpio-hog
related boot issues").

It fixes the issue that the gpio ranges needs to be defined before
gpiochip_add().

Therefore, we also have to swap the order of registering the pinctrl
driver and registering the gpio chip.

You also have to add the "gpio-ranges" property to the pinctrl device
node to get it finally working.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit a0752e9c ]

Commit 21abf103
("gpio: Pass a flag to gpiochip_request_own_desc()")
started to pass an enum gpiod_flags but this file is
not including the header file that defines that enum
and the compiler spits:

drivers/memory/omap-gpmc.c: In function
			    'gpmc_probe_generic_child':
drivers/memory/omap-gpmc.c:2174:9: error: type of formal
				   parameter 4 is incomplete
         0);
         ^

Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Fixes: 21abf103 ("gpio: Pass a flag to gpiochip_request_own_desc()")
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 8ba35b3a ]

Clang warns:

samples/vfio-mdev/mtty.c:592:39: warning: implicit conversion from 'int'
to 'char' changes value from 162 to -94 [-Wconstant-conversion]
                *buf = UART_MSR_DSR | UART_MSR_DDSR | UART_MSR_DCD;
                     ~ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~
1 warning generated.

Turns out that all uses of buf in this function ultimately end up stored
or cast to an unsigned type. Just use u8, which has the same number of
bits but can store this larger number so Clang no longer warns.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit fe6e6561 ]

Show x86-64 specific blacklisted symbols in debugfs.

Since x86-64 prohibits probing on symbols which are in
entry text, those should be shown.
Tested-by: Andrea Righi <righi.andrea@gmail.com>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Yonghong Song <yhs@fb.com>
Link: http://lkml.kernel.org/r/154503488425.26176.17136784384033608516.stgit@devboxSigned-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit fb1a59fa ]

Blacklist symbols in arch-defined probe-prohibited areas.
With this change, user can see all symbols which are prohibited
to probe in debugfs.

All archtectures which have custom prohibit areas should define
its own arch_populate_kprobe_blacklist() function, but unless that,
all symbols marked __kprobes are blacklisted.
Reported-by: Andrea Righi <righi.andrea@gmail.com>
Tested-by: Andrea Righi <righi.andrea@gmail.com>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Yonghong Song <yhs@fb.com>
Link: http://lkml.kernel.org/r/154503485491.26176.15823229545155174796.stgit@devboxSigned-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 1669907e ]

If pcistub_init_device fails, the release function will be called with
dev_data set to NULL.  Check it before using it to avoid a NULL pointer
dereference.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit bf9445a3 ]

Blacklist symbols in Xen probe-prohibited areas, so that user can see
these prohibited symbols in debugfs.

See also: a50480cb.
Signed-off-by: Andrea Righi <righi.andrea@gmail.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 6d7f677a ]

When a serial port gets faulty or gets flooded with inputs, its interrupt
handler starts to work double time to get the characters to the workqueue
for the tty layer to handle them. When this busy time on the serial/tty
subsystem happens during boot, where it is also busy on the userspace
trying to initialise, some processes can continuously get preempted
and will be on hold until the interrupts subside.

The fix is to backoff on processing received characters for a specified
amount of time when an input overrun is seen (received a new character
before the previous one is processed). This only stops receive and will
continue to transmit characters to serial port. After the backoff period
is done, it receive will be re-enabled. This is optional and will only
be enabled by setting 'overrun-throttle-ms' in the dts.
Signed-off-by: Darwin Dingel <darwin.dingel@alliedtelesis.co.nz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 85af74c4 ]

We're getting a reference RPi's firmware node in order to be able to
communicate with it's driver. We should decrease the reference count on
the dt node after being done with it.

Fixes: a98d90e7 ("gpio: raspberrypi-exp: Driver for RPi3 GPIO expander via mailbox service")
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 6e0856d3 ]

The memory chunk allocated by hid_allocate_device() should be released
by hid_destroy_device(), not kfree().

Fixes: 0b28cb4b("HID: intel-ish-hid: ISH HID client driver")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 2e948218 ]

When falling back to PIO, active_rx must be set to a different value
than cookie_rx[i], else sci_dma_rx_find_active() will incorrectly find a
match, leading to a NULL pointer dereference in rx_timer_fn() later.

Use zero instead, which is the same value as after driver
initialization.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 158ffa36 ]

We use this number to figure out how many delayed refs to run, but
__btrfs_run_delayed_refs really only checks every time we need a new
delayed ref head, so we always run at least one ref head completely no
matter what the number of items on it.  Fix the accounting to only be
adjusted when we add/remove a ref head.

In addition to using this number to limit the number of delayed refs
run, a future patch is also going to use it to calculate the amount of
space required for delayed refs space reservation.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 0e6ec385 ]

We can have a lot freed extents during the life span of transaction, so
the red black tree that keeps track of the ranges of each freed extent
(fs_info->freed_extents[]) can get quite big. When finishing a
transaction commit we find each range, process it (discard the extents,
unpin them) and then remove it from the red black tree.

We can use an extent state record as a cache when searching for a range,
so that when we clean the range we can use the cached extent state we
passed to the search function instead of iterating the red black tree
again. Doing things as fast as possible when finishing a transaction (in
state TRANS_STATE_UNBLOCKED) is convenient as it reduces the time we
block another task that wants to commit the next transaction.

So change clear_extent_dirty() to allow an optional extent state record to
be passed as an argument, which will be passed down to __clear_extent_bit.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit b47dda2e ]

The device-replace needs to check the result code of the scrub workers
in btrfs_dev_replace_cancel and distinguish if successful cancel
operation and when the there was no operation running.

If btrfs_scrub_cancel() fails, return
BTRFS_IOCTL_DEV_REPLACE_RESULT_NOT_STARTED so that user can try
to cancel the replace again.
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ update changelog ]
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit da612e31 ]

RAID5 and RAID6 profile store one copy of the data, not 2 or 3. These
values are not yet used anywhere so there's no change.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Hans van Kranenburg <hans.van.kranenburg@mendix.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit fc8a168a ]

Before btrfs_map_bio submits all stripe bios it does a number of checks
to ensure the device for every stripe is present. However, it doesn't do
a DEV_STATE_MISSING check, instead this is relegated to the lower level
btrfs_schedule_bio (in the async submission case, sync submission
doesn't check DEV_STATE_MISSING at all). Additionally
btrfs_schedule_bios does the duplicate device->bdev check which has
already been performed in btrfs_map_bio.

This patch moves the DEV_STATE_MISSING check in btrfs_map_bio and
removes the duplicate device->bdev check. Doing so ensures that no bio
cloning/submission happens for both async/sync requests in the face of
missing device. This makes the async io submission path slightly shorter
in terms of instruction count. No functional changes.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 8dc7623b ]

PHY model is being used on omap5 platforms even if port mode
is not OMAP_EHCI_PORT_MODE_PHY. So don't guess if PHY is required
or not based on PHY mode.

If PHY is provided in device tree, it must be required. So, if
devm_usb_get_phy_by_phandle() gives us an error code other
than -ENODEV (no PHY) then error out.

This fixes USB Ethernet on omap5-uevm if PHY happens to
probe after EHCI thus causing a -EPROBE_DEFER.

Cc: Johan Hovold <johan@kernel.org>
Cc: Ladislav Michl <ladis@linux-mips.org>
Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>