No need to force NVMe device driver to be compiled in if the
lightnvm subsystem is selected. Also no need for PCI to be selected
as well, as it would be selected by the device driver that hooks into
the subsystem.
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Reviewed-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Lot of controllers may have only one irq vector for completing IO
request. And usually affinity of the only irq vector is all possible
CPUs, however, on most of ARCH, there may be only one specific CPU
for handling this interrupt.

So if all IOs are completed in hardirq context, it is inevitable to
degrade IO performance because of increased irq latency.

This patch tries to address this issue by allowing to complete request
in softirq context, like the legacy IO path.

IOPS is observed as ~13%+ in the following randread test on raid0 over
virtio-scsi.

mdadm --create --verbose /dev/md0 --level=0 --chunk=1024 --raid-devices=8 /dev/sdb /dev/sdc /dev/sdd /dev/sde /dev/sdf /dev/sdg /dev/sdh /dev/sdi

fio --time_based --name=benchmark --runtime=30 --filename=/dev/md0 --nrfiles=1 --ioengine=libaio --iodepth=32 --direct=1 --invalidate=1 --verify=0 --verify_fatal=0 --numjobs=32 --rw=randread --blocksize=4k

Cc: Dongli Zhang <dongli.zhang@oracle.com>
Cc: Zach Marano <zmarano@google.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Jianchao Wang <jianchao.w.wang@oracle.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

when the nbuckets of cache device is smaller than 1024, making cache
device will trigger BUG_ON in kernel, add a condition to avoid this.
Reported-by: nitroxis <n@nxs.re>
Signed-off-by: Dongbo Cao <cdbdyx@163.com>
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Split the combined '||' statements in if() check, to make the code easier
for debug.
Signed-off-by: Dongbo Cao <cdbdyx@163.com>
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Current cache_set has MAX_CACHES_PER_SET caches most, and the macro
is used for
"
	struct cache *cache_by_alloc[MAX_CACHES_PER_SET];
"
in the define of struct cache_set.

Use MAX_CACHES_PER_SET instead of magic number 8 in
__bch_bucket_alloc_set.
Signed-off-by: Shenghui Wang <shhuiw@foxmail.com>
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

In extents.c:bch_extent_bad(), number 96 is used as parameter to call
btree_bug_on(). The purpose is to check whether stale gen value exceeds
BUCKET_GC_GEN_MAX, so it is better to use macro BUCKET_GC_GEN_MAX to
make the code more understandable.
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Parameter "struct kobject *kobj" in bch_debug_init() is useless,
remove it in this patch.
Signed-off-by: Dongbo Cao <cdbdyx@163.com>
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

struct kmem_cache *bch_passthrough_cache is not used in
bcache code. Remove it.
Signed-off-by: Shenghui Wang <shhuiw@foxmail.com>
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Recal cached_dev_sectors on cached_dev detached, as recal done on
cached_dev attached.

Update the cached_dev_sectors before bcache_device_detach called
as bcache_device_detach will set bcache_device->c to NULL.
Signed-off-by: Shenghui Wang <shhuiw@foxmail.com>
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

refill->end record the last key of writeback, for example, at the first
time, keys (1,128K) to (1,1024K) are flush to the backend device, but
the end key (1,1024K) is not included, since the bellow code:
	if (bkey_cmp(k, refill->end) >= 0) {
		ret = MAP_DONE;
		goto out;
	}
And in the next time when we refill writeback keybuf again, we searched
key start from (1,1024K), and got a key bigger than it, so the key
(1,1024K) missed.
This patch modify the above code, and let the end key to be included to
the writeback key buffer.
Signed-off-by: Tang Junhui <tang.junhui.linux@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Forgot to include the maintainers with my first email.

Somewhere between Michael Lyle's original
"bcache: PI controller for writeback rate V2" patch dated 07 Sep 2017
and 1d316e65 bcache: implement PI controller for writeback rate,
the mapping of the writeback_rate_minimum attribute was dropped.

Re-add the missing sysfs writeback_rate_minimum attribute mapping to
"allow the user to specify a minimum rate at which dirty blocks are
retired."

Fixes: 1d316e65 ("bcache: implement PI controller for writeback rate")
Signed-off-by: Ben Peddell <klightspeed@killerwolves.net>
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

When bcache device is clean, dirty keys may still exist after
journal replay, so we need to count these dirty keys even
device in clean status, otherwise after writeback, the amount
of dirty data would be incorrect.
Signed-off-by: Tang Junhui <tang.junhui.linux@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

The code comments of closure_return_with_destructor() in closure.h makrs
function name as closure_return(). This patch fixes this type with the
correct name - closure_return_with_destructor.
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

When doing ioctl in flash device, it will call ioctl_dev() in super.c,
then we should not to get cached device since flash only device has
no backend device. This patch just move the jugement dc->io_disable
to cached_dev_ioctl() to make ioctl in flash device correctly.

Fixes: 0f0709e6 ("bcache: stop bcache device when backing device is offline")
Signed-off-by: Tang Junhui <tang.junhui.linux@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

In cached_dev_cache_miss() and check_should_bypass(), REQ_META is used
to check whether a bio is for metadata request. REQ_META is used for
blktrace, the correct REQ_ flag should be REQ_PRIO. This flag means the
bio should be prior to other bio, and frequently be used to indicate
metadata io in file system code.

This patch replaces REQ_META with correct flag REQ_PRIO.

CC Adam Manzanares because he explains to me what REQ_PRIO is for.
Signed-off-by: Coly Li <colyli@suse.de>
Cc: Adam Manzanares <adam.manzanares@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Missed reading IOs are identified by s->cache_missed, not the
s->cache_miss, so in trace_bcache_read() using trace_bcache_read
to identify whether the IO is missed or not.
Signed-off-by: Tang Junhui <tang.junhui.linux@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

UUIDs are considered as metadata. __uuid_write should add the number
of buckets (in sectors) written to disk to ca->meta_sectors_written.
Currently only 1 bucket is used in uuid write.

Steps to test:
1) create a fresh backing device and a fresh cache device separately.
   The backing device didn't attach to any cache set.
2) cd /sys/block/<cache device>/bcache
   cat metadata_written      // record the output value
   cat bucket_size
3) attach the backing device to cache set
4) cat metadata_written
   The output value is almost the same as the value in step 2
   before the change.
   After the change, the value is bigger about 1 bucket size.
Signed-off-by: Shenghui Wang <shhuiw@foxmail.com>
Reviewed-by: Tang Junhui <tang.junhui.linux@gmail.com>
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

When debugging e.g. the SCSI timeout handler it is important that
requests that have not yet been started or that already have
completed are also reported through debugfs.

Cc: Christoph Hellwig <hch@lst.de>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Pull NVMe updates from Christoph:

"A relatively boring merge window:

 - better AEN tracing (Chaitanya)
 - NUMA aware PCIe multipathing (me)
 - RDMA workqueue fixes (Sagi)
 - better bio usage in the target (Sagi)
 - FC rework for target removal (James)
 - better multipath handling of ->queue_rq failures (James)
 - various cleanups (Milan)"

* 'nvme-4.20' of git://git.infradead.org/nvme:
  nvmet-rdma: use a private workqueue for delete
  nvme: take node locality into account when selecting a path
  nvmet: don't split large I/Os unconditionally
  nvme: call nvme_complete_rq when nvmf_check_ready fails for mpath I/O
  nvme-core: add async event trace helper
  nvme_fc: add 'nvme_discovery' sysfs attribute to fc transport device
  nvmet_fc: support target port removal with nvmet layer
  nvme-fc: fix for a minor typos
  nvmet: remove redundant module prefix
  nvme: fix typo in nvme_identify_ns_descs

Queue deletion is done asynchronous when the last reference on the queue
is dropped.  Thus, in order to make sure we don't over allocate under a
connect/disconnect storm, we let queue deletion complete before making
forward progress.

However, given that we flush the system_wq from rdma_cm context which
runs from a workqueue context, we can have a circular locking complaint
[1]. Fix that by using a private workqueue for queue deletion.

[1]:
======================================================
WARNING: possible circular locking dependency detected
4.19.0-rc4-dbg+ #3 Not tainted
------------------------------------------------------
kworker/5:0/39 is trying to acquire lock:
00000000a10b6db9 (&id_priv->handler_mutex){+.+.}, at: rdma_destroy_id+0x6f/0x440 [rdma_cm]

but task is already holding lock:
00000000331b4e2c ((work_completion)(&queue->release_work)){+.+.}, at: process_one_work+0x3ed/0xa20

which lock already depends on the new lock.

the existing dependency chain (in reverse order) is:

-> #3 ((work_completion)(&queue->release_work)){+.+.}:
       process_one_work+0x474/0xa20
       worker_thread+0x63/0x5a0
       kthread+0x1cf/0x1f0
       ret_from_fork+0x24/0x30

-> #2 ((wq_completion)"events"){+.+.}:
       flush_workqueue+0xf3/0x970
       nvmet_rdma_cm_handler+0x133d/0x1734 [nvmet_rdma]
       cma_ib_req_handler+0x72f/0xf90 [rdma_cm]
       cm_process_work+0x2e/0x110 [ib_cm]
       cm_req_handler+0x135b/0x1c30 [ib_cm]
       cm_work_handler+0x2b7/0x38cd [ib_cm]
       process_one_work+0x4ae/0xa20
nvmet_rdma:nvmet_rdma_cm_handler: nvmet_rdma: disconnected (10): status 0 id 0000000040357082
       worker_thread+0x63/0x5a0
       kthread+0x1cf/0x1f0
       ret_from_fork+0x24/0x30
nvme nvme0: Reconnecting in 10 seconds...

-> #1 (&id_priv->handler_mutex/1){+.+.}:
       __mutex_lock+0xfe/0xbe0
       mutex_lock_nested+0x1b/0x20
       cma_ib_req_handler+0x6aa/0xf90 [rdma_cm]
       cm_process_work+0x2e/0x110 [ib_cm]
       cm_req_handler+0x135b/0x1c30 [ib_cm]
       cm_work_handler+0x2b7/0x38cd [ib_cm]
       process_one_work+0x4ae/0xa20
       worker_thread+0x63/0x5a0
       kthread+0x1cf/0x1f0
       ret_from_fork+0x24/0x30

-> #0 (&id_priv->handler_mutex){+.+.}:
       lock_acquire+0xc5/0x200
       __mutex_lock+0xfe/0xbe0
       mutex_lock_nested+0x1b/0x20
       rdma_destroy_id+0x6f/0x440 [rdma_cm]
       nvmet_rdma_release_queue_work+0x8e/0x1b0 [nvmet_rdma]
       process_one_work+0x4ae/0xa20
       worker_thread+0x63/0x5a0
       kthread+0x1cf/0x1f0
       ret_from_fork+0x24/0x30

Fixes: 777dc823 ("nvmet-rdma: occasionally flush ongoing controller teardown")
Reported-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Tested-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>

Some time ago REQ_DISCARD was renamed into REQ_OP_DISCARD. Some comments
and documentation files were not updated however. Update these comments
and documentation files. See also commit 4e1b2d52 ("block, fs,
drivers: remove REQ_OP compat defs and related code").
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Philipp Reisner <philipp.reisner@linbit.com>
Cc: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

There is another cast from unsigned long to int which causes
a bounds check to fail with specially crafted input. The value is
then used as an index in the slot array in cdrom_slot_status().

This issue is similar to CVE-2018-16658 and CVE-2018-10940.
Signed-off-by: Young_X <YangX92@hotmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Replace "fallthru" with a proper "fall through" annotation.

This fix is part of the ongoing efforts to enabling
-Wimplicit-fallthrough
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Make current_path an array with an entry for every possible node, and
cache the best path on a per-node basis.  Take the node distance into
account when selecting it.  This is primarily useful for dual-ported PCIe
devices which are connected to PCIe root ports on different sockets.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>

If we know that the I/O size exceeds our inline bio vec, no
point using it and split the rest to begin with. We could
in theory reuse the inline bio and only allocate the bio_vec,
but its really not worth optimizing for.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>

When an io is rejected by nvmf_check_ready() due to validation of the
controller state, the nvmf_fail_nonready_command() will normally return
BLK_STS_RESOURCE to requeue and retry.  However, if the controller is
dying or the I/O is marked for NVMe multipath, the I/O is failed so that
the controller can terminate or so that the io can be issued on a
different path.  Unfortunately, as this reject point is before the
transport has accepted the command, blk-mq ends up completing the I/O
and never calls nvme_complete_rq(), which is where multipath may preserve
or re-route the I/O. The end result is, the device user ends up seeing an
EIO error.

Example: single path connectivity, controller is under load, and a reset
is induced.  An I/O is received:

  a) while the reset state has been set but the queues have yet to be
     stopped; or
  b) after queues are started (at end of reset) but before the reconnect
     has completed.

The I/O finishes with an EIO status.

This patch makes the following changes:

  - Adds the HOST_PATH_ERROR pathing status from TP4028
  - Modifies the reject point such that it appears to queue successfully,
    but actually completes the io with the new pathing status and calls
    nvme_complete_rq().
  - nvme_complete_rq() recognizes the new status, avoids resetting the
    controller (likely was already done in order to get this new status),
    and calls the multipather to clear the current path that errored.
    This allows the next command (retry or new command) to select a new
    path if there is one.
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>

This patch adds a new event for nvme async event notification.
We print the async event in the decoded format when we recognize
the event otherwise we just dump the result.
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

The fc transport device should allow for a rediscovery, as userspace
might have lost the events. Example is udev events not handled during
system startup.

This patch add a sysfs entry 'nvme_discovery' on the fc class to
have it replay all udev discovery events for all local port/remote
port address pairs.
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

Currently, if a targetport has been connected to via the nvmet config
(in other words, the add_port() transport routine called, and the nvmet
port pointer stored for using in upcalls on new io), and if the
targetport is then removed (say the lldd driver decides to unload or
fully reset its hardware) and then re-added (the lldd driver reloads or
reinits its hardware), the port pointer has been lost so there's no way
to continue to post commands up to nvmet via the transport port.

Correct by allocating a small "port context" structure that will be
linked to by the targetport. The context will save the targetport WWN's
and the nvmet port pointer to use for it.  Initial allocation will occur
when the targetport is bound to via add_port.  The context will be
deallocated when remove_port() is called.  If a targetport is removed
while nvmet has the active port context, the targetport will be unlinked
from the port context before removal.  If a new targetport is registered,
the port contexts without a binding are looked through and if the WWN's
match (so it's the same as nvmet's port context) the port context is
linked to the new target port.  Thus new io can be received on the new
targetport and operation resumes with nvmet.

Additionally, this also resolves nvmet configuration changing out from
underneath of the nvme-fc target port (for example: a nvmetcli clear).
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

Signed-off-by: Milan P. Gandhi <mgandhi@redhat.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

This patch removes the redundant module prefix used in the pr_err() when
nvmet_get_smart_log_nsid() failed to find the namespace provided as a part
of smart-log command.
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

Signed-off-by: Milan P. Gandhi <mgandhi@redhat.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

Merge -rc6 in, for two reasons:

1) Resolve a trivial conflict in the blk-mq-tag.c documentation
2) A few important regression fixes went into upstream directly, so
   they aren't in the 4.20 branch.
Signed-off-by: Jens Axboe <axboe@kernel.dk>

* tag 'v4.19-rc6': (780 commits)
  Linux 4.19-rc6
  MAINTAINERS: fix reference to moved drivers/{misc => auxdisplay}/panel.c
  cpufreq: qcom-kryo: Fix section annotations
  perf/core: Add sanity check to deal with pinned event failure
  xen/blkfront: correct purging of persistent grants
  Revert "xen/blkfront: When purging persistent grants, keep them in the buffer"
  selftests/powerpc: Fix Makefiles for headers_install change
  blk-mq: I/O and timer unplugs are inverted in blktrace
  dax: Fix deadlock in dax_lock_mapping_entry()
  x86/boot: Fix kexec booting failure in the SEV bit detection code
  bcache: add separate workqueue for journal_write to avoid deadlock
  drm/amd/display: Fix Edid emulation for linux
  drm/amd/display: Fix Vega10 lightup on S3 resume
  drm/amdgpu: Fix vce work queue was not cancelled when suspend
  Revert "drm/panel: Add device_link from panel device to DRM device"
  xen/blkfront: When purging persistent grants, keep them in the buffer
  clocksource/drivers/timer-atmel-pit: Properly handle error cases
  block: fix deadline elevator drain for zoned block devices
  ACPI / hotplug / PCI: Don't scan for non-hotplug bridges if slot is not bridge
  drm/syncobj: Don't leak fences when WAIT_FOR_SUBMIT is set
  ...
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Miguel writes:
  "A trivial fix for auxdisplay

    - MAINTAINERS reference fix for moved file
      Reported by Joe Perches"

* tag 'auxdisplay-for-greg-v4.19-rc6' of https://github.com/ojeda/linux:
  MAINTAINERS: fix reference to moved drivers/{misc => auxdisplay}/panel.c

Merge tag 'libnvdimm-fixes2-4.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm

Dan writes:
  "filesystem-dax for 4.19-rc6

   Fix a deadlock in the new for 4.19 dax_lock_mapping_entry() routine."

* tag 'libnvdimm-fixes2-4.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  dax: Fix deadlock in dax_lock_mapping_entry()

Commit 51c1e9b5 ("auxdisplay: Move panel.c to drivers/auxdisplay folder")
moved the file, but the MAINTAINERS reference was not updated.

Link: https://lore.kernel.org/lkml/20180928220131.31075-1-joe@perches.com/Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>

Jens writes:
  "Block fixes for 4.19-rc6

   A set of fixes that should go into this release. This pull request
   contains:

   - A fix (hopefully) for the persistent grants for xen-blkfront. A
     previous fix from this series wasn't complete, hence reverted, and
     this one should hopefully be it. (Boris Ostrovsky)

   - Fix for an elevator drain warning with SMR devices, which is
     triggered when you switch schedulers (Damien)

   - bcache deadlock fix (Guoju Fang)

   - Fix for the block unplug tracepoint, which has had the
     timer/explicit flag reverted since 4.11 (Ilya)

   - Fix a regression in this series where the blk-mq timeout hook is
     invoked with the RCU read lock held, hence preventing it from
     blocking (Keith)

   - NVMe pull from Christoph, with a single multipath fix (Susobhan Dey)"

* tag 'for-linus-20180929' of git://git.kernel.dk/linux-block:
  xen/blkfront: correct purging of persistent grants
  Revert "xen/blkfront: When purging persistent grants, keep them in the buffer"
  blk-mq: I/O and timer unplugs are inverted in blktrace
  bcache: add separate workqueue for journal_write to avoid deadlock
  xen/blkfront: When purging persistent grants, keep them in the buffer
  block: fix deadline elevator drain for zoned block devices
  blk-mq: Allow blocking queue tag iter callbacks
  nvme: properly propagate errors in nvme_mpath_init

Thomas writes:
  "A single fix for the AMD memory encryption boot code so it does not
   read random garbage instead of the cached encryption bit when a kexec
   kernel is allocated above the 32bit address limit."

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/boot: Fix kexec booting failure in the SEV bit detection code

Thomas writes:
  "Three small fixes for clocksource drivers:
   - Proper error handling in the Atmel PIT driver
   - Add CLOCK_SOURCE_SUSPEND_NONSTOP for TI SoCs so suspend works again
   - Fix the next event function for Facebook Backpack-CMM BMC chips so
     usleep(100) doesnt sleep several milliseconds"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  clocksource/drivers/timer-atmel-pit: Properly handle error cases
  clocksource/drivers/fttmr010: Fix set_next_event handler
  clocksource/drivers/ti-32k: Add CLOCK_SOURCE_SUSPEND_NONSTOP flag for non-am43 SoCs