- 16 Jun, 2009 40 commits
-
-
Uri Shkolnik authored
Add new GPIO management interface to replace old (buggy) one. Keeping old interface intact for now. Signed-off-by:
Uri Shkolnik <uris@siano-ms.com> Acked-by:
Michael Krufky <mkrufky@linuxtv.org> Signed-off-by:
Mauro Carvalho Chehab <mchehab@redhat.com>
-
Uri Shkolnik authored
Make the SDIO interface driver a stand alone module. Signed-off-by:
-
Uri Shkolnik authored
Add two additional USB targets, add these to the 'cards' modules and to the 'smsusb' module. Signed-off-by:
-
Uri Shkolnik authored
Change the debug message of the USB interface driver exit function. Signed-off-by:
-
Uri Shkolnik authored
Fix small typo in the module description Signed-off-by:
-
Uri Shkolnik authored
Fix bug that cause error log to echo also if success Signed-off-by:
-
Uri Shkolnik authored
Signed-off-by:
-
Uri Shkolnik authored
Fix byte ordering bug. Signed-off-by:
-
Uri Shkolnik authored
get common buffers() should block operation until valid buffer is avaliable. Signed-off-by:
-
Uri Shkolnik authored
Assign using the new gpio structures, i/o for exist HPG targets, without removing the old implementation. Signed-off-by:
-
Uri Shkolnik authored
Remove wrong firmware assignments for Nova, Stellar Signed-off-by:
-
Uri Shkolnik authored
The card modules is the component which handles various targets, so the IDs table should reside within it. [mchehab@redhat.com: add missing smsendian.h include at smscoreapi.c] Signed-off-by:
-
Uri Shkolnik authored
Add the infra-red to the makefile and declare the assignment in the cards components. [mchehab@redhat.com: Fixed a few trivial merge conflicts] Signed-off-by:
-
Uri Shkolnik authored
Add gpio look-up table for various requirements, any target may select any gpio and assign it to a function Signed-off-by:
-
Uri Shkolnik authored
Move the DVB-API v3 headers' include list from the core component to the smsdvb (DVB adapter) which is the only one that uses them. Signed-off-by:
-
Uri Shkolnik authored
Fix type at the module description Signed-off-by:
-
Uri Shkolnik authored
This patch replace the old method of pulling the device status by sending "get_statistics" request, to push mode. This make status update much faster, and reduce various operation time (UHF scan now takes 15s instead of 2m). In order to make the change the following modification have been applied: 1) core header - update statistics headers. 2) dvb adapter - omit the statistics request, add handling of status indications. 3) core 'onresponse' - re-route messages addressed to other adapter to the dvb adapter. Signed-off-by:
-
Uri Shkolnik authored
Add support for Siano protocol messages with big endian systems. Signed-off-by:
-
Mauro Carvalho Chehab authored
Cc: Uri Shkolnik <urishk@yahoo.com> Signed-off-by: -
Uri Shkolnik authored
Add smsendian component to the module build Signed-off-by:
-
Uri Shkolnik authored
This patch fixes a problem were protocol buffers have been lost during USB disconnect events. Signed-off-by:
-
Uri Shkolnik authored
This patch adds support for byte ordering and big endianity handling for the USB interface driver Signed-off-by:
-
Uri Shkolnik authored
This patch updates the license of the USB interface driver Signed-off-by:
-
Uri Shkolnik authored
Remove redundant complete instruction from smsdvb, in the past this was used by the statistics state machine, but no longer. Signed-off-by:
-
Uri Shkolnik authored
Siano: smsdvb - Fix license to match all other Siano's files Signed-off-by:
-
Uri Shkolnik authored
Re-order the include files list Re-order the include files list, put the DVB-API v3 within its own section, within a define container. Signed-off-by:
-
Uri Shkolnik authored
Modify the file license to match all other Siano's files Signed-off-by:
-
Uri Shkolnik authored
Add code that modify the content of Siano's protocol messages when running with big-endian target. Signed-off-by:
-
Uri Shkolnik authored
This patch add support for IR (infra-red) remote controllers. Further commits are needed in order to enable the activation of the IR components. Signed-off-by:
-
Uri Shkolnik authored
Some more indentation for the smscoreapi.h There are no implementation changes in this patch. Signed-off-by:
-
Uri Shkolnik authored
smscoreapi - move the main core structure declaration to the header, in order to enable other components (such as IR) to use it. Signed-off-by:
-
Uri Shkolnik authored
Add new definitions (of Siano's protocol messages), and protocol structures (for future commits usage) Signed-off-by:
-
Uri Shkolnik authored
Remove two redundant lines, based on Klimov Alexey code review. Signed-off-by:
-
Miroslav Sustek authored
cx88-dsp: fixing 64bit math on 32bit kernels Some gcc versions report the missing of __divdi3 [mchehab.redhat.com: CodingStyle fixes] Signed-off-by:
Miroslav Sustek <sustmidown@centrum.cz> Signed-off-by:
-
Marton Balint authored
This patch changes cx88_set_stereo to avoid resetting all of the audio registers on stereo/mono change if the audio standard is A2, and set only the AUD_CTL register. The benefit of this method is that it eliminates the annoying clicking noise on setting the audio mode to stereo or mono. The driver had used the same method 1.5 years ago (and for FM radio it still does), but a pretty big cleanup commit changed it to the "complete audio reset" method, although the reason for this move was not clear. (If somebody knows why it was necessary, please let me know!) The original commit: http://linuxtv.org/hg/v4l-dvb/rev/ffe313541d7dSigned-off-by:
Marton Balint <cus@fazekas.hu> Signed-off-by:
-
Marton Balint authored
The sole purpose of the audio thread is to detect if stereo transmission is available, and if it is, then switch to stereo mode (and switch back, if it's no longer available). This manual autodetection is useful for some audio standards (e.g. A2) where cx88_get_stereo CAN detect stereo sound, but the cx2388x chip CANNOT auto-detect stereo sound. However, for other audio standards, the cx2388x chip CAN auto-detect the stereo sound, so the manual autodetection in the audio thread is not needed. In fact, it can cause serious problems because for some of these audio standards, cx88_get_stereo CANNOT detect the presence of stereo sound. Besides that, if the hardware automatically detects stereo/mono sound, you cannot set core->audiomode_current to the real current audio mode on channel change. With this patch, the manual autodetection is only used if audiomode_current is known after a channel change (because of the initial mono mode), and hardware-based stereo autodetecion is not applicable for the current audio standard. Signed-off-by:
-
Marton Balint authored
The patch implements reliable stereo and sap detection for the A2 sound standard. This is achieved by processing the samples of the audio RDS fifo of the cx2388x chip. A2M, EIAJ and BTSC stereo/sap detection is also possible with this new approach, but it's not implemented yet. Stereo detection when alsa handles the sound also does not work yet. Signed-off-by:
-
Uri Shkolnik authored
This patch provides SDIO interface driver for SMS (Siano Mobile Silicon) based devices. The patch includes SMS high level SDIO driver and requires patching the kernel SDIO stack, those stack patches had been provided previously. I would like to thank Pierre Ossman, MMC maintainer, who wrote this driver. Signed-off-by:
Pierre Ossman <drzeus@drzeus.cx> Signed-off-by:
-
Uri Shkolnik authored
sdio: add cards id for sms (Siano Mobile Silicon) MDTV receivers Add SDIO vendor ID, and multiple device IDs for various SMS-based MDTV SDIO adapters. Signed-off-by:
-
Michael Krufky authored
Signed-off-by: Michael Krufky <kernellabs.com> Signed-off-by:
-
