Commits · a069215cf5985f3aa1bba550264907d6bd05c5f7 · nexedi / linux

18 Mar, 2018 3 commits

net: fec: Fix unbalanced PM runtime calls · a069215c

Florian Fainelli authored Mar 18, 2018

When unbinding/removing the driver, we will run into the following warnings:

[  259.655198] fec 400d1000.ethernet: 400d1000.ethernet supply phy not found, using dummy regulator
[  259.665065] fec 400d1000.ethernet: Unbalanced pm_runtime_enable!
[  259.672770] fec 400d1000.ethernet (unnamed net_device) (uninitialized): Invalid MAC address: 00:00:00:00:00:00
[  259.683062] fec 400d1000.ethernet (unnamed net_device) (uninitialized): Using random MAC address: f2:3e:93:b7:29:c1
[  259.696239] libphy: fec_enet_mii_bus: probed

Avoid these warnings by balancing the runtime PM calls during fec_drv_remove().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

a069215c

vmxnet3: use correct flag to indicate LRO feature · 034f4057

Ronak Doshi authored Mar 16, 2018

'Commit 45dac1d6 ("vmxnet3: Changes for vmxnet3 adapter version 2
(fwd)")' introduced a flag "lro" in structure vmxnet3_adapter which is
used to indicate whether LRO is enabled or not. However, the patch
did not set the flag and hence it was never exercised.

So, when LRO is enabled, it resulted in poor TCP performance due to
delayed acks. This issue is seen with packets which are larger than
the mss getting a delayed ack rather than an immediate ack, thus
resulting in high latency.

This patch removes the lro flag and directly uses device features
against NETIF_F_LRO to check if lro is enabled.

Fixes: 45dac1d6 ("vmxnet3: Changes for vmxnet3 adapter version 2 (fwd)")
Reported-by: Rachel Lunnon <rachel_lunnon@stormagic.com>
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Acked-by: Shrikrishna Khare <skhare@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

034f4057

vmxnet3: avoid xmit reset due to a race in vmxnet3 · 7a4c003d

Ronak Doshi authored Mar 16, 2018

The field txNumDeferred is used by the driver to keep track of the number
of packets it has pushed to the emulation. The driver increments it on
pushing the packet to the emulation and the emulation resets it to 0 at
the end of the transmit.

There is a possibility of a race either when (a) ESX is under heavy load or
(b) workload inside VM is of low packet rate.

This race results in xmit hangs when network coalescing is disabled. This
change creates a local copy of txNumDeferred and uses it to perform ring
arithmetic.
Reported-by: Noriho Tanaka <ntanaka@vmware.com>
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Acked-by: Shrikrishna Khare <skhare@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

7a4c003d

17 Mar, 2018 10 commits

Merge branch 'tcf_foo_init-NULL-deref' · 78f1b04f

David S. Miller authored Mar 17, 2018

Davide Caratti says:

====================
net/sched: fix NULL dereference in the error path of .init()

with several TC actions it's possible to see NULL pointer dereference,
when the .init() function calls tcf_idr_alloc(), fails at some point and
then calls tcf_idr_release(): this series fixes all them introducing
non-NULL tests in the .cleanup() function.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

78f1b04f

net/sched: fix NULL dereference on the error path of tcf_skbmod_init() · 2d433610

Davide Caratti authored Mar 16, 2018

when the following command

 # tc action replace action skbmod swap mac index 100

is run for the first time, and tcf_skbmod_init() fails to allocate struct
tcf_skbmod_params, tcf_skbmod_cleanup() calls kfree_rcu(NULL), thus
causing the following error:

 BUG: unable to handle kernel NULL pointer dereference at 0000000000000008
 IP: __call_rcu+0x23/0x2b0
 PGD 8000000034057067 P4D 8000000034057067 PUD 74937067 PMD 0
 Oops: 0002 [#1] SMP PTI
 Modules linked in: act_skbmod(E) psample ip6table_filter ip6_tables iptable_filter binfmt_misc ext4 snd_hda_codec_generic snd_hda_intel snd_hda_codec crct10dif_pclmul mbcache jbd2 crc32_pclmul snd_hda_core ghash_clmulni_intel snd_hwdep pcbc snd_seq snd_seq_device snd_pcm aesni_intel snd_timer crypto_simd glue_helper snd cryptd virtio_balloon joydev soundcore pcspkr i2c_piix4 nfsd auth_rpcgss nfs_acl lockd grace sunrpc ip_tables xfs libcrc32c ata_generic pata_acpi qxl drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops ttm drm virtio_console virtio_net virtio_blk ata_piix libata crc32c_intel virtio_pci serio_raw virtio_ring virtio i2c_core floppy dm_mirror dm_region_hash dm_log dm_mod [last unloaded: act_skbmod]
 CPU: 3 PID: 3144 Comm: tc Tainted: G            E    4.16.0-rc4.act_vlan.orig+ #403
 Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
 RIP: 0010:__call_rcu+0x23/0x2b0
 RSP: 0018:ffffbd2e403e7798 EFLAGS: 00010246
 RAX: ffffffffc0872080 RBX: ffff981d34bff780 RCX: 00000000ffffffff
 RDX: ffffffff922a5f00 RSI: 0000000000000000 RDI: 0000000000000000
 RBP: 0000000000000000 R08: 0000000000000001 R09: 000000000000021f
 R10: 000000003d003000 R11: 0000000000aaaaaa R12: 0000000000000000
 R13: ffffffff922a5f00 R14: 0000000000000001 R15: ffff981d3b698c2c
 FS:  00007f3678292740(0000) GS:ffff981d3fd80000(0000) knlGS:0000000000000000
 CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
 CR2: 0000000000000008 CR3: 000000007c57a006 CR4: 00000000001606e0
 Call Trace:
  __tcf_idr_release+0x79/0xf0
  tcf_skbmod_init+0x1d1/0x210 [act_skbmod]
  tcf_action_init_1+0x2cc/0x430
  tcf_action_init+0xd3/0x1b0
  tc_ctl_action+0x18b/0x240
  rtnetlink_rcv_msg+0x29c/0x310
  ? _cond_resched+0x15/0x30
  ? __kmalloc_node_track_caller+0x1b9/0x270
  ? rtnl_calcit.isra.28+0x100/0x100
  netlink_rcv_skb+0xd2/0x110
  netlink_unicast+0x17c/0x230
  netlink_sendmsg+0x2cd/0x3c0
  sock_sendmsg+0x30/0x40
  ___sys_sendmsg+0x27a/0x290
  ? filemap_map_pages+0x34a/0x3a0
  ? __handle_mm_fault+0xbfd/0xe20
  __sys_sendmsg+0x51/0x90
  do_syscall_64+0x6e/0x1a0
  entry_SYSCALL_64_after_hwframe+0x3d/0xa2
 RIP: 0033:0x7f36776a3ba0
 RSP: 002b:00007fff4703b618 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
 RAX: ffffffffffffffda RBX: 00007fff4703b740 RCX: 00007f36776a3ba0
 RDX: 0000000000000000 RSI: 00007fff4703b690 RDI: 0000000000000003
 RBP: 000000005aaaba36 R08: 0000000000000002 R09: 0000000000000000
 R10: 00007fff4703b0a0 R11: 0000000000000246 R12: 0000000000000000
 R13: 00007fff4703b754 R14: 0000000000000001 R15: 0000000000669f60
 Code: 5d e9 42 da ff ff 66 90 0f 1f 44 00 00 41 57 41 56 41 55 49 89 d5 41 54 55 48 89 fd 53 48 83 ec 08 40 f6 c7 07 0f 85 19 02 00 00 <48> 89 75 08 48 c7 45 00 00 00 00 00 9c 58 0f 1f 44 00 00 49 89
 RIP: __call_rcu+0x23/0x2b0 RSP: ffffbd2e403e7798
 CR2: 0000000000000008

Fix it in tcf_skbmod_cleanup(), ensuring that kfree_rcu(p, ...) is called
only when p is not NULL.

Fixes: 86da71b5 ("net_sched: Introduce skbmod action")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

2d433610

net/sched: fix NULL dereference in the error path of tcf_sample_init() · 1f110e7c

Davide Caratti authored Mar 16, 2018

when the following command

 # tc action add action sample rate 100 group 100 index 100

is run for the first time, and psample_group_get(100) fails to create a
new group, tcf_sample_cleanup() calls psample_group_put(NULL), thus
causing the following error:

 BUG: unable to handle kernel NULL pointer dereference at 000000000000001c
 IP: psample_group_put+0x15/0x71 [psample]
 PGD 8000000075775067 P4D 8000000075775067 PUD 7453c067 PMD 0
 Oops: 0002 [#1] SMP PTI
 Modules linked in: act_sample(E) psample ip6table_filter ip6_tables iptable_filter binfmt_misc ext4 snd_hda_codec_generic snd_hda_intel snd_hda_codec snd_hda_core mbcache jbd2 crct10dif_pclmul snd_hwdep crc32_pclmul snd_seq ghash_clmulni_intel pcbc snd_seq_device snd_pcm aesni_intel crypto_simd snd_timer glue_helper snd cryptd joydev pcspkr i2c_piix4 soundcore virtio_balloon nfsd auth_rpcgss nfs_acl lockd grace sunrpc ip_tables xfs libcrc32c ata_generic pata_acpi qxl drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops ttm drm virtio_net ata_piix virtio_console virtio_blk libata serio_raw crc32c_intel virtio_pci i2c_core virtio_ring virtio floppy dm_mirror dm_region_hash dm_log dm_mod [last unloaded: act_tunnel_key]
 CPU: 2 PID: 5740 Comm: tc Tainted: G            E    4.16.0-rc4.act_vlan.orig+ #403
 Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
 RIP: 0010:psample_group_put+0x15/0x71 [psample]
 RSP: 0018:ffffb8a80032f7d0 EFLAGS: 00010246
 RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000024
 RDX: 0000000000000001 RSI: 0000000000000000 RDI: ffffffffc06d93c0
 RBP: 0000000000000000 R08: 0000000000000001 R09: 0000000000000044
 R10: 00000000bd003000 R11: ffff979fba04aa59 R12: 0000000000000000
 R13: 0000000000000000 R14: 0000000000000000 R15: ffff979fbba3f22c
 FS:  00007f7638112740(0000) GS:ffff979fbfd00000(0000) knlGS:0000000000000000
 CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
 CR2: 000000000000001c CR3: 00000000734ea001 CR4: 00000000001606e0
 Call Trace:
  __tcf_idr_release+0x79/0xf0
  tcf_sample_init+0x125/0x1d0 [act_sample]
  tcf_action_init_1+0x2cc/0x430
  tcf_action_init+0xd3/0x1b0
  tc_ctl_action+0x18b/0x240
  rtnetlink_rcv_msg+0x29c/0x310
  ? _cond_resched+0x15/0x30
  ? __kmalloc_node_track_caller+0x1b9/0x270
  ? rtnl_calcit.isra.28+0x100/0x100
  netlink_rcv_skb+0xd2/0x110
  netlink_unicast+0x17c/0x230
  netlink_sendmsg+0x2cd/0x3c0
  sock_sendmsg+0x30/0x40
  ___sys_sendmsg+0x27a/0x290
  ? filemap_map_pages+0x34a/0x3a0
  ? __handle_mm_fault+0xbfd/0xe20
  __sys_sendmsg+0x51/0x90
  do_syscall_64+0x6e/0x1a0
  entry_SYSCALL_64_after_hwframe+0x3d/0xa2
 RIP: 0033:0x7f7637523ba0
 RSP: 002b:00007fff0473ef58 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
 RAX: ffffffffffffffda RBX: 00007fff0473f080 RCX: 00007f7637523ba0
 RDX: 0000000000000000 RSI: 00007fff0473efd0 RDI: 0000000000000003
 RBP: 000000005aaaac80 R08: 0000000000000002 R09: 0000000000000000
 R10: 00007fff0473e9e0 R11: 0000000000000246 R12: 0000000000000000
 R13: 00007fff0473f094 R14: 0000000000000001 R15: 0000000000669f60
 Code: be 02 00 00 00 48 89 df e8 a9 fe ff ff e9 7c ff ff ff 0f 1f 40 00 0f 1f 44 00 00 53 48 89 fb 48 c7 c7 c0 93 6d c0 e8 db 20 8c ef <83> 6b 1c 01 74 10 48 c7 c7 c0 93 6d c0 ff 14 25 e8 83 83 b0 5b
 RIP: psample_group_put+0x15/0x71 [psample] RSP: ffffb8a80032f7d0
 CR2: 000000000000001c

Fix it in tcf_sample_cleanup(), ensuring that calls to psample_group_put(p)
are done only when p is not NULL.

Fixes: cadb9c9f ("net/sched: act_sample: Fix error path in init")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

1f110e7c

net/sched: fix NULL dereference in the error path of tunnel_key_init() · abdadd3c

Davide Caratti authored Mar 16, 2018

when the following command

 # tc action add action tunnel_key unset index 100

is run for the first time, and tunnel_key_init() fails to allocate struct
tcf_tunnel_key_params, tunnel_key_release() dereferences NULL pointers.
This causes the following error:

 BUG: unable to handle kernel NULL pointer dereference at 0000000000000010
 IP: tunnel_key_release+0xd/0x40 [act_tunnel_key]
 PGD 8000000033787067 P4D 8000000033787067 PUD 74646067 PMD 0
 Oops: 0000 [#1] SMP PTI
 Modules linked in: act_tunnel_key(E) act_csum ip6table_filter ip6_tables iptable_filter binfmt_misc ext4 mbcache jbd2 crct10dif_pclmul crc32_pclmul snd_hda_codec_generic ghash_clmulni_intel snd_hda_intel pcbc snd_hda_codec snd_hda_core snd_hwdep snd_seq aesni_intel snd_seq_device crypto_simd glue_helper snd_pcm cryptd joydev snd_timer pcspkr virtio_balloon snd i2c_piix4 soundcore nfsd auth_rpcgss nfs_acl lockd grace sunrpc ip_tables xfs libcrc32c ata_generic pata_acpi qxl drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops ttm virtio_net virtio_blk drm virtio_console crc32c_intel ata_piix serio_raw i2c_core virtio_pci libata virtio_ring virtio floppy dm_mirror dm_region_hash dm_log dm_mod
 CPU: 2 PID: 3101 Comm: tc Tainted: G            E    4.16.0-rc4.act_vlan.orig+ #403
 Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
 RIP: 0010:tunnel_key_release+0xd/0x40 [act_tunnel_key]
 RSP: 0018:ffffba46803b7768 EFLAGS: 00010286
 RAX: ffffffffc09010a0 RBX: 0000000000000000 RCX: 0000000000000024
 RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff99ee336d7480
 RBP: 0000000000000000 R08: 0000000000000001 R09: 0000000000000044
 R10: 0000000000000220 R11: ffff99ee79d73131 R12: 0000000000000000
 R13: ffff99ee32d67610 R14: ffff99ee7671dc38 R15: 00000000fffffff4
 FS:  00007febcb2cd740(0000) GS:ffff99ee7fd00000(0000) knlGS:0000000000000000
 CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
 CR2: 0000000000000010 CR3: 000000007c8e4005 CR4: 00000000001606e0
 Call Trace:
  __tcf_idr_release+0x79/0xf0
  tunnel_key_init+0xd9/0x460 [act_tunnel_key]
  tcf_action_init_1+0x2cc/0x430
  tcf_action_init+0xd3/0x1b0
  tc_ctl_action+0x18b/0x240
  rtnetlink_rcv_msg+0x29c/0x310
  ? _cond_resched+0x15/0x30
  ? __kmalloc_node_track_caller+0x1b9/0x270
  ? rtnl_calcit.isra.28+0x100/0x100
  netlink_rcv_skb+0xd2/0x110
  netlink_unicast+0x17c/0x230
  netlink_sendmsg+0x2cd/0x3c0
  sock_sendmsg+0x30/0x40
  ___sys_sendmsg+0x27a/0x290
  __sys_sendmsg+0x51/0x90
  do_syscall_64+0x6e/0x1a0
  entry_SYSCALL_64_after_hwframe+0x3d/0xa2
 RIP: 0033:0x7febca6deba0
 RSP: 002b:00007ffe7b0dd128 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
 RAX: ffffffffffffffda RBX: 00007ffe7b0dd250 RCX: 00007febca6deba0
 RDX: 0000000000000000 RSI: 00007ffe7b0dd1a0 RDI: 0000000000000003
 RBP: 000000005aaa90cb R08: 0000000000000002 R09: 0000000000000000
 R10: 00007ffe7b0dcba0 R11: 0000000000000246 R12: 0000000000000000
 R13: 00007ffe7b0dd264 R14: 0000000000000001 R15: 0000000000669f60
 Code: 44 00 00 8b 0d b5 23 00 00 48 8b 87 48 10 00 00 48 8b 3c c8 e9 a5 e5 d8 c3 0f 1f 44 00 00 0f 1f 44 00 00 53 48 8b 9f b0 00 00 00 <83> 7b 10 01 74 0b 48 89 df 31 f6 5b e9 f2 fa 7f c3 48 8b 7b 18
 RIP: tunnel_key_release+0xd/0x40 [act_tunnel_key] RSP: ffffba46803b7768
 CR2: 0000000000000010

Fix this in tunnel_key_release(), ensuring 'param' is not NULL before
dereferencing it.

Fixes: d0f6dd8a ("net/sched: Introduce act_tunnel_key")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

abdadd3c

net/sched: fix NULL dereference in the error path of tcf_csum_init() · aab378a7

Davide Caratti authored Mar 16, 2018

when the following command

 # tc action add action csum udp continue index 100

is run for the first time, and tcf_csum_init() fails allocating struct
tcf_csum, tcf_csum_cleanup() calls kfree_rcu(NULL,...). This causes the
following error:

 BUG: unable to handle kernel NULL pointer dereference at 0000000000000010
 IP: __call_rcu+0x23/0x2b0
 PGD 80000000740b4067 P4D 80000000740b4067 PUD 32e7f067 PMD 0
 Oops: 0002 [#1] SMP PTI
 Modules linked in: act_csum(E) act_vlan ip6table_filter ip6_tables iptable_filter binfmt_misc ext4 mbcache jbd2 crct10dif_pclmul crc32_pclmul ghash_clmulni_intel snd_hda_codec_generic pcbc snd_hda_intel snd_hda_codec snd_hda_core snd_hwdep snd_seq snd_seq_device snd_pcm snd_timer aesni_intel crypto_simd glue_helper cryptd snd joydev pcspkr virtio_balloon i2c_piix4 soundcore nfsd auth_rpcgss nfs_acl lockd grace sunrpc ip_tables xfs libcrc32c ata_generic pata_acpi qxl drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops ttm virtio_blk drm virtio_net virtio_console ata_piix crc32c_intel libata virtio_pci serio_raw i2c_core virtio_ring virtio floppy dm_mirror dm_region_hash dm_log dm_mod [last unloaded: act_vlan]
 CPU: 2 PID: 5763 Comm: tc Tainted: G            E    4.16.0-rc4.act_vlan.orig+ #403
 Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
 RIP: 0010:__call_rcu+0x23/0x2b0
 RSP: 0018:ffffb275803e77c0 EFLAGS: 00010246
 RAX: ffffffffc057b080 RBX: ffff9674bc6f5240 RCX: 00000000ffffffff
 RDX: ffffffff928a5f00 RSI: 0000000000000008 RDI: 0000000000000008
 RBP: 0000000000000008 R08: 0000000000000001 R09: 0000000000000044
 R10: 0000000000000220 R11: ffff9674b9ab4821 R12: 0000000000000000
 R13: ffffffff928a5f00 R14: 0000000000000000 R15: 0000000000000001
 FS:  00007fa6368d8740(0000) GS:ffff9674bfd00000(0000) knlGS:0000000000000000
 CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
 CR2: 0000000000000010 CR3: 0000000073dec001 CR4: 00000000001606e0
 Call Trace:
  __tcf_idr_release+0x79/0xf0
  tcf_csum_init+0xfb/0x180 [act_csum]
  tcf_action_init_1+0x2cc/0x430
  tcf_action_init+0xd3/0x1b0
  tc_ctl_action+0x18b/0x240
  rtnetlink_rcv_msg+0x29c/0x310
  ? _cond_resched+0x15/0x30
  ? __kmalloc_node_track_caller+0x1b9/0x270
  ? rtnl_calcit.isra.28+0x100/0x100
  netlink_rcv_skb+0xd2/0x110
  netlink_unicast+0x17c/0x230
  netlink_sendmsg+0x2cd/0x3c0
  sock_sendmsg+0x30/0x40
  ___sys_sendmsg+0x27a/0x290
  ? filemap_map_pages+0x34a/0x3a0
  ? __handle_mm_fault+0xbfd/0xe20
  __sys_sendmsg+0x51/0x90
  do_syscall_64+0x6e/0x1a0
  entry_SYSCALL_64_after_hwframe+0x3d/0xa2
 RIP: 0033:0x7fa635ce9ba0
 RSP: 002b:00007ffc185b0fc8 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
 RAX: ffffffffffffffda RBX: 00007ffc185b10f0 RCX: 00007fa635ce9ba0
 RDX: 0000000000000000 RSI: 00007ffc185b1040 RDI: 0000000000000003
 RBP: 000000005aaa85e0 R08: 0000000000000002 R09: 0000000000000000
 R10: 00007ffc185b0a20 R11: 0000000000000246 R12: 0000000000000000
 R13: 00007ffc185b1104 R14: 0000000000000001 R15: 0000000000669f60
 Code: 5d e9 42 da ff ff 66 90 0f 1f 44 00 00 41 57 41 56 41 55 49 89 d5 41 54 55 48 89 fd 53 48 83 ec 08 40 f6 c7 07 0f 85 19 02 00 00 <48> 89 75 08 48 c7 45 00 00 00 00 00 9c 58 0f 1f 44 00 00 49 89
 RIP: __call_rcu+0x23/0x2b0 RSP: ffffb275803e77c0
 CR2: 0000000000000010

fix this in tcf_csum_cleanup(), ensuring that kfree_rcu(param, ...) is
called only when param is not NULL.

Fixes: 9c5f69bb ("net/sched: act_csum: don't use spinlock in the fast path")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

aab378a7

net/sched: fix NULL dereference in the error path of tcf_vlan_init() · 1edf8abe

Davide Caratti authored Mar 16, 2018

when the following command

 # tc actions replace action vlan pop index 100

is run for the first time, and tcf_vlan_init() fails allocating struct
tcf_vlan_params, tcf_vlan_cleanup() calls kfree_rcu(NULL, ...). This causes
the following error:

 BUG: unable to handle kernel NULL pointer dereference at 0000000000000018
 IP: __call_rcu+0x23/0x2b0
 PGD 80000000760a2067 P4D 80000000760a2067 PUD 742c1067 PMD 0
 Oops: 0002 [#1] SMP PTI
 Modules linked in: act_vlan(E) ip6table_filter ip6_tables iptable_filter binfmt_misc ext4 snd_hda_codec_generic snd_hda_intel mbcache snd_hda_codec jbd2 snd_hda_core crct10dif_pclmul crc32_pclmul ghash_clmulni_intel pcbc snd_hwdep snd_seq snd_seq_device snd_pcm aesni_intel crypto_simd snd_timer glue_helper snd cryptd joydev soundcore virtio_balloon pcspkr i2c_piix4 nfsd auth_rpcgss nfs_acl lockd grace sunrpc ip_tables xfs libcrc32c ata_generic pata_acpi qxl drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops ttm drm virtio_console virtio_blk virtio_net ata_piix crc32c_intel libata virtio_pci i2c_core virtio_ring serio_raw virtio floppy dm_mirror dm_region_hash dm_log dm_mod [last unloaded: act_vlan]
 CPU: 3 PID: 3119 Comm: tc Tainted: G            E    4.16.0-rc4.act_vlan.orig+ #403
 Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
 RIP: 0010:__call_rcu+0x23/0x2b0
 RSP: 0018:ffffaac3005fb798 EFLAGS: 00010246
 RAX: ffffffffc0704080 RBX: ffff97f2b4bbe900 RCX: 00000000ffffffff
 RDX: ffffffffabca5f00 RSI: 0000000000000010 RDI: 0000000000000010
 RBP: 0000000000000010 R08: 0000000000000001 R09: 0000000000000044
 R10: 00000000fd003000 R11: ffff97f2faab5b91 R12: 0000000000000000
 R13: ffffffffabca5f00 R14: ffff97f2fb80202c R15: 00000000fffffff4
 FS:  00007f68f75b4740(0000) GS:ffff97f2ffd80000(0000) knlGS:0000000000000000
 CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
 CR2: 0000000000000018 CR3: 0000000072b52001 CR4: 00000000001606e0
 Call Trace:
  __tcf_idr_release+0x79/0xf0
  tcf_vlan_init+0x168/0x270 [act_vlan]
  tcf_action_init_1+0x2cc/0x430
  tcf_action_init+0xd3/0x1b0
  tc_ctl_action+0x18b/0x240
  rtnetlink_rcv_msg+0x29c/0x310
  ? _cond_resched+0x15/0x30
  ? __kmalloc_node_track_caller+0x1b9/0x270
  ? rtnl_calcit.isra.28+0x100/0x100
  netlink_rcv_skb+0xd2/0x110
  netlink_unicast+0x17c/0x230
  netlink_sendmsg+0x2cd/0x3c0
  sock_sendmsg+0x30/0x40
  ___sys_sendmsg+0x27a/0x290
  ? filemap_map_pages+0x34a/0x3a0
  ? __handle_mm_fault+0xbfd/0xe20
  __sys_sendmsg+0x51/0x90
  do_syscall_64+0x6e/0x1a0
  entry_SYSCALL_64_after_hwframe+0x3d/0xa2
 RIP: 0033:0x7f68f69c5ba0
 RSP: 002b:00007fffd79c1118 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
 RAX: ffffffffffffffda RBX: 00007fffd79c1240 RCX: 00007f68f69c5ba0
 RDX: 0000000000000000 RSI: 00007fffd79c1190 RDI: 0000000000000003
 RBP: 000000005aaa708e R08: 0000000000000002 R09: 0000000000000000
 R10: 00007fffd79c0ba0 R11: 0000000000000246 R12: 0000000000000000
 R13: 00007fffd79c1254 R14: 0000000000000001 R15: 0000000000669f60
 Code: 5d e9 42 da ff ff 66 90 0f 1f 44 00 00 41 57 41 56 41 55 49 89 d5 41 54 55 48 89 fd 53 48 83 ec 08 40 f6 c7 07 0f 85 19 02 00 00 <48> 89 75 08 48 c7 45 00 00 00 00 00 9c 58 0f 1f 44 00 00 49 89
 RIP: __call_rcu+0x23/0x2b0 RSP: ffffaac3005fb798
 CR2: 0000000000000018

fix this in tcf_vlan_cleanup(), ensuring that kfree_rcu(p, ...) is called
only when p is not NULL.

Fixes: 4c5b9d96 ("act_vlan: VLAN action rewrite to use RCU lock/unlock and update")
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Manish Kurup <manish.kurup@verizon.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

1edf8abe

net: ethernet: ti: cpsw: add check for in-band mode setting with RGMII PHY interface · f9db5069

SZ Lin (林上智) authored Mar 16, 2018

According to AM335x TRM[1] 14.3.6.2, AM437x TRM[2] 15.3.6.2 and
DRA7 TRM[3] 24.11.4.8.7.3.3, in-band mode in EXT_EN(bit18) register is only
available when PHY is configured in RGMII mode with 10Mbps speed. It will
cause some networking issues without RGMII mode, such as carrier sense
errors and low throughput. TI also mentioned this issue in their forum[4].

This patch adds the check mechanism for PHY interface with RGMII interface
type, the in-band mode can only be set in RGMII mode with 10Mbps speed.

References:
[1]: https://www.ti.com/lit/ug/spruh73p/spruh73p.pdf
[2]: http://www.ti.com/lit/ug/spruhl7h/spruhl7h.pdf
[3]: http://www.ti.com/lit/ug/spruic2b/spruic2b.pdf
[4]: https://e2e.ti.com/support/arm/sitara_arm/f/791/p/640765/2392155Suggested-by: Holsety Chen (陳憲輝) <Holsety.Chen@moxa.com>
Signed-off-by: SZ Lin (林上智) <sz.lin@moxa.com>
Signed-off-by: Schuyler Patton <spatton@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

f9db5069

net: hns: Fix ethtool private flags · d61d263c

Matthias Brugger authored Mar 15, 2018

The driver implementation returns support for private flags, while
no private flags are present. When asked for the number of private
flags it returns the number of statistic flag names.

Fix this by returning EOPNOTSUPP for not implemented ethtool flags.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

d61d263c

mlxsw: spectrum_buffers: Set a minimum quota for CPU port traffic · bcdd5de8

Ido Schimmel authored Mar 15, 2018

In commit 9ffcc372 ("mlxsw: spectrum: Allow packets to be trapped
from any PG") I fixed a problem where packets could not be trapped to
the CPU due to exceeded shared buffer quotas. The mentioned commit
explains the problem in detail.

The problem was fixed by assigning a minimum quota for the CPU port and
the traffic class used for scheduling traffic to the CPU.

However, commit 117b0dad ("mlxsw: Create a different trap group list
for each device") assigned different traffic classes to different
packet types and rendered the fix useless.

Fix the problem by assigning a minimum quota for the CPU port and all
the traffic classes that are currently in use.

Fixes: 117b0dad ("mlxsw: Create a different trap group list for each device")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Eddie Shklaer <eddies@mellanox.com>
Tested-by: Eddie Shklaer <eddies@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bcdd5de8

net: sched: fix uses after free · cce6294c

Eric Dumazet authored Mar 14, 2018

syzbot reported one use-after-free in pfifo_fast_enqueue() [1]

Issue here is that we can not reuse skb after a successful skb_array_produce()
since another cpu might have consumed it already.

I believe a similar problem exists in try_bulk_dequeue_skb_slow()
in case we put an skb into qdisc_enqueue_skb_bad_txq() for lockless qdisc.

[1]
BUG: KASAN: use-after-free in qdisc_pkt_len include/net/sch_generic.h:610 [inline]
BUG: KASAN: use-after-free in qdisc_qstats_cpu_backlog_inc include/net/sch_generic.h:712 [inline]
BUG: KASAN: use-after-free in pfifo_fast_enqueue+0x4bc/0x5e0 net/sched/sch_generic.c:639
Read of size 4 at addr ffff8801cede37e8 by task syzkaller717588/5543

CPU: 1 PID: 5543 Comm: syzkaller717588 Not tainted 4.16.0-rc4+ #265
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:17 [inline]
 dump_stack+0x194/0x24d lib/dump_stack.c:53
 print_address_description+0x73/0x250 mm/kasan/report.c:256
 kasan_report_error mm/kasan/report.c:354 [inline]
 kasan_report+0x23c/0x360 mm/kasan/report.c:412
 __asan_report_load4_noabort+0x14/0x20 mm/kasan/report.c:432
 qdisc_pkt_len include/net/sch_generic.h:610 [inline]
 qdisc_qstats_cpu_backlog_inc include/net/sch_generic.h:712 [inline]
 pfifo_fast_enqueue+0x4bc/0x5e0 net/sched/sch_generic.c:639
 __dev_xmit_skb net/core/dev.c:3216 [inline]

Fixes: c5ad119f ("net: sched: pfifo_fast use skb_array")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot+ed43b6903ab968b16f54@syzkaller.appspotmail.com
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc:	Cong Wang <xiyou.wangcong@gmail.com>
Cc:	Jiri Pirko <jiri@resnulli.us>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cce6294c

16 Mar, 2018 13 commits

net: dsa: mv88e6xxx: Fix binding documentation for MDIO busses · 7b7ef57c

Andrew Lunn authored Mar 16, 2018

The MDIO busses are switch properties and so should be inside the
switch node. Fix the examples in the binding document.
Reported-by: 尤晓杰 <yxj790222@163.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Fixes: a3c53be5 ("net: dsa: mv88e6xxx: Support multiple MDIO busses")
Signed-off-by: David S. Miller <davem@davemloft.net>

7b7ef57c

skbuff: Fix not waking applications when errors are enqueued · 6e5d58fd

Vinicius Costa Gomes authored Mar 14, 2018

When errors are enqueued to the error queue via sock_queue_err_skb()
function, it is possible that the waiting application is not notified.

Calling 'sk->sk_data_ready()' would not notify applications that
selected only POLLERR events in poll() (for example).

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Reported-by: Randy E. Witt <randy.e.witt@intel.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

6e5d58fd

netlink: avoid a double skb free in genlmsg_mcast() · 02a2385f

Nicolas Dichtel authored Mar 14, 2018

nlmsg_multicast() consumes always the skb, thus the original skb must be
freed only when this function is called with a clone.

Fixes: cb9f7a9a ("netlink: ensure to loop over all netns in genlmsg_multicast_allns()")
Reported-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

02a2385f

qede: Fix qedr link update · 4609adc2

Michal Kalderon authored Mar 14, 2018

Link updates were not reported to qedr correctly.
Leading to cases where a link could be down, but qedr
would see it as up.
In addition, once qede was loaded, link state would be up,
regardless of the actual link state.
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

4609adc2

Merge branch 'qed-iWARP-related-fixes' · b225598d

David S. Miller authored Mar 16, 2018

Michal Kalderon says:

====================
qed: iWARP related fixes

This series contains two fixes related to iWARP flow.
====================
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>

b225598d

qed: Fix non TCP packets should be dropped on iWARP ll2 connection · 16da0904

Michal Kalderon authored Mar 14, 2018

FW workaround. The iWARP LL2 connection did not expect TCP packets
to arrive on it's connection. The fix drops any non-tcp packets

Fixes b5c29ca7 ("qed: iWARP CM - setup a ll2 connection for handling
SYN packets")
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

16da0904

qed: Fix MPA unalign flow in case header is split across two packets. · 933e8c91

Michal Kalderon authored Mar 14, 2018

There is a corner case in the MPA unalign flow where a FPDU header is
split over two tcp segments. The length of the first fragment in this
case was not initialized properly and should be '1'

Fixes: c7d1d839 ("qed: Add support for MPA header being split over two tcp packets")
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

933e8c91

net/iucv: Free memory obtained by kzalloc · fa6a91e9

Arvind Yadav authored Mar 13, 2018

Free memory by calling put_device(), if afiucv_iucv_init is not
successful.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

fa6a91e9

net: systemport: Rewrite __bcm_sysport_tx_reclaim() · 484d802d

Florian Fainelli authored Mar 13, 2018

There is no need for complex checking between the last consumed index
and current consumed index, a simple subtraction will do.

This also eliminates the possibility of a permanent transmit queue stall
under the following conditions:

- one CPU bursts ring->size worth of traffic (up to 256 buffers), to the
  point where we run out of free descriptors, so we stop the transmit
  queue at the end of bcm_sysport_xmit()

- because of our locking, we have the transmit process disable
  interrupts which means we can be blocking the TX reclamation process

- when TX reclamation finally runs, we will be computing the difference
  between ring->c_index (last consumed index by SW) and what the HW
  reports through its register

- this register is masked with (ring->size - 1) = 0xff, which will lead
  to stripping the upper bits of the index (register is 16-bits wide)

- we will be computing last_tx_cn as 0, which means there is no work to
  be done, and we never wake-up the transmit queue, leaving it
  permanently disabled

A practical example is e.g: ring->c_index aka last_c_index = 12, we
pushed 256 entries, HW consumer index = 268, we mask it with 0xff = 12,
so last_tx_cn == 0, nothing happens.

Fixes: 80105bef ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

484d802d

kcm: lock lower socket in kcm_attach · 2cc683e8

Tom Herbert authored Mar 13, 2018

Need to lock lower socket in order to provide mutual exclusion
with kcm_unattach.

v2: Add Reported-by for syzbot

Fixes: ab7ac4eb ("kcm: Kernel Connection Multiplexor module")
Reported-by: syzbot+ea75c0ffcd353d32515f064aaebefc5279e6161e@syzkaller.appspotmail.com
Signed-off-by: Tom Herbert <tom@quantonium.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

2cc683e8

Merge branch 'vlan-untag-and-insert-fixes' · e693be29

David S. Miller authored Mar 16, 2018

Toshiaki Makita says:

====================
Fix vlan untag and insertion for bridge and vlan with reorder_hdr off

As Brandon Carpenter reported[1], sending non-vlan-offloaded packets from
bridge devices ends up with corrupted packets. He narrowed down this problem
and found that the root cause is in skb_reorder_vlan_header().

While I was working on fixing this problem, I found that the function does
not work properly for double tagged packets with reorder_hdr off as well.

Patch 1 fixes these 2 problems in skb_reorder_vlan_header().

And it turned out that fixing skb_reorder_vlan_header() is not sufficient
to receive double tagged packets with reorder_hdr off while I was testing the
fix. Vlan tags got out of order when vlan devices with reorder_hdr disabled
were stacked. Patch 2 fixes this problem.

[1] https://www.spinics.net/lists/linux-ethernet-bridging/msg07039.html
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

e693be29

vlan: Fix out of order vlan headers with reorder header off · cbe7128c

Toshiaki Makita authored Mar 13, 2018

With reorder header off, received packets are untagged in skb_vlan_untag()
called from within __netif_receive_skb_core(), and later the tag will be
inserted back in vlan_do_receive().

This caused out of order vlan headers when we create a vlan device on top
of another vlan device, because vlan_do_receive() inserts a tag as the
outermost vlan tag. E.g. the outer tag is first removed in skb_vlan_untag()
and inserted back in vlan_do_receive(), then the inner tag is next removed
and inserted back as the outermost tag.

This patch fixes the behaviour by inserting the inner tag at the right
position.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

cbe7128c

net: Fix vlan untag for bridge and vlan_dev with reorder_hdr off · 4bbb3e0e

Toshiaki Makita authored Mar 13, 2018

When we have a bridge with vlan_filtering on and a vlan device on top of
it, packets would be corrupted in skb_vlan_untag() called from
br_dev_xmit().

The problem sits in skb_reorder_vlan_header() used in skb_vlan_untag(),
which makes use of skb->mac_len. In this function mac_len is meant for
handling rx path with vlan devices with reorder_header disabled, but in
tx path mac_len is typically 0 and cannot be used, which is the problem
in this case.

The current code even does not properly handle rx path (skb_vlan_untag()
called from __netif_receive_skb_core()) with reorder_header off actually.

In rx path single tag case, it works as follows:

- Before skb_reorder_vlan_header()

 mac_header                                data
   v                                        v
   +-------------------+-------------+------+----
   |        ETH        |    VLAN     | ETH  |
   |       ADDRS       | TPID | TCI  | TYPE |
   +-------------------+-------------+------+----
   <-------- mac_len --------->
                       <------------->
                        to be removed

- After skb_reorder_vlan_header()

            mac_header                     data
                 v                          v
                 +-------------------+------+----
                 |        ETH        | ETH  |
                 |       ADDRS       | TYPE |
                 +-------------------+------+----
                 <-------- mac_len --------->

This is ok, but in rx double tag case, it corrupts packets:

- Before skb_reorder_vlan_header()

 mac_header                                              data
   v                                                      v
   +-------------------+-------------+-------------+------+----
   |        ETH        |    VLAN     |    VLAN     | ETH  |
   |       ADDRS       | TPID | TCI  | TPID | TCI  | TYPE |
   +-------------------+-------------+-------------+------+----
   <--------------- mac_len ---------------->
                                     <------------->
                                    should be removed
                       <--------------------------->
                         actually will be removed

- After skb_reorder_vlan_header()

            mac_header                                   data
                 v                                        v
                               +-------------------+------+----
                               |        ETH        | ETH  |
                               |       ADDRS       | TYPE |
                               +-------------------+------+----
                 <--------------- mac_len ---------------->

So, two of vlan tags are both removed while only inner one should be
removed and mac_header (and mac_len) is broken.

skb_vlan_untag() is meant for removing the vlan header at (skb->data - 2),
so use skb->data and skb->mac_header to calculate the right offset.
Reported-by: Brandon Carpenter <brandon.carpenter@cypherpath.com>
Fixes: a6e18ff1 ("vlan: Fix untag operations of stacked vlans with REORDER_HEADER off")
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

4bbb3e0e

15 Mar, 2018 2 commits

net sched actions: return explicit error when tunnel_key mode is not specified · 51d4740f

Roman Mashak authored Mar 12, 2018

If set/unset mode of the tunnel_key action is not provided, ->init() still
returns 0, and the caller proceeds with bogus 'struct tc_action *' object,
this results in crash:

% tc actions add action tunnel_key src_ip 1.1.1.1 dst_ip 2.2.2.1 id 7 index 1

[   35.805515] general protection fault: 0000 [#1] SMP PTI
[   35.806161] Modules linked in: act_tunnel_key kvm_intel kvm irqbypass
crct10dif_pclmul crc32_pclmul ghash_clmulni_intel pcbc aesni_intel aes_x86_64
crypto_simd glue_helper cryptd serio_raw
[   35.808233] CPU: 1 PID: 428 Comm: tc Not tainted 4.16.0-rc4+ #286
[   35.808929] RIP: 0010:tcf_action_init+0x90/0x190
[   35.809457] RSP: 0018:ffffb8edc068b9a0 EFLAGS: 00010206
[   35.810053] RAX: 1320c000000a0003 RBX: 0000000000000001 RCX: 0000000000000000
[   35.810866] RDX: 0000000000000070 RSI: 0000000000007965 RDI: ffffb8edc068b910
[   35.811660] RBP: ffffb8edc068b9d0 R08: 0000000000000000 R09: ffffb8edc068b808
[   35.812463] R10: ffffffffc02bf040 R11: 0000000000000040 R12: ffffb8edc068bb38
[   35.813235] R13: 0000000000000000 R14: 0000000000000000 R15: ffffb8edc068b910
[   35.814006] FS:  00007f3d0d8556c0(0000) GS:ffff91d1dbc40000(0000)
knlGS:0000000000000000
[   35.814881] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   35.815540] CR2: 000000000043f720 CR3: 0000000019248001 CR4: 00000000001606a0
[   35.816457] Call Trace:
[   35.817158]  tc_ctl_action+0x11a/0x220
[   35.817795]  rtnetlink_rcv_msg+0x23d/0x2e0
[   35.818457]  ? __slab_alloc+0x1c/0x30
[   35.819079]  ? __kmalloc_node_track_caller+0xb1/0x2b0
[   35.819544]  ? rtnl_calcit.isra.30+0xe0/0xe0
[   35.820231]  netlink_rcv_skb+0xce/0x100
[   35.820744]  netlink_unicast+0x164/0x220
[   35.821500]  netlink_sendmsg+0x293/0x370
[   35.822040]  sock_sendmsg+0x30/0x40
[   35.822508]  ___sys_sendmsg+0x2c5/0x2e0
[   35.823149]  ? pagecache_get_page+0x27/0x220
[   35.823714]  ? filemap_fault+0xa2/0x640
[   35.824423]  ? page_add_file_rmap+0x108/0x200
[   35.825065]  ? alloc_set_pte+0x2aa/0x530
[   35.825585]  ? finish_fault+0x4e/0x70
[   35.826140]  ? __handle_mm_fault+0xbc1/0x10d0
[   35.826723]  ? __sys_sendmsg+0x41/0x70
[   35.827230]  __sys_sendmsg+0x41/0x70
[   35.827710]  do_syscall_64+0x68/0x120
[   35.828195]  entry_SYSCALL_64_after_hwframe+0x3d/0xa2
[   35.828859] RIP: 0033:0x7f3d0ca4da67
[   35.829331] RSP: 002b:00007ffc9f284338 EFLAGS: 00000246 ORIG_RAX:
000000000000002e
[   35.830304] RAX: ffffffffffffffda RBX: 00007ffc9f284460 RCX: 00007f3d0ca4da67
[   35.831247] RDX: 0000000000000000 RSI: 00007ffc9f2843b0 RDI: 0000000000000003
[   35.832167] RBP: 000000005aa6a7a9 R08: 0000000000000001 R09: 0000000000000000
[   35.833075] R10: 00000000000005f1 R11: 0000000000000246 R12: 0000000000000000
[   35.833997] R13: 00007ffc9f2884c0 R14: 0000000000000001 R15: 0000000000674640
[   35.834923] Code: 24 30 bb 01 00 00 00 45 31 f6 eb 5e 8b 50 08 83 c2 07 83 e2
fc 83 c2 70 49 8b 07 48 8b 40 70 48 85 c0 74 10 48 89 14 24 4c 89 ff <ff> d0 48
8b 14 24 48 01 c2 49 01 d6 45 85 ed 74 05 41 83 47 2c
[   35.837442] RIP: tcf_action_init+0x90/0x190 RSP: ffffb8edc068b9a0
[   35.838291] ---[ end trace a095c06ee4b97a26 ]---

Fixes: d0f6dd8a ("net/sched: Introduce act_tunnel_key")
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

51d4740f

net/smc: simplify wait when closing listen socket · 3d502067

Ursula Braun authored Mar 13, 2018

Closing of a listen socket wakes up kernel_accept() of
smc_tcp_listen_worker(), and then has to wait till smc_tcp_listen_worker()
gives up the internal clcsock. The wait logic introduced with
commit 127f4970 ("net/smc: release clcsock from tcp_listen_worker")
might wait longer than necessary. This patch implements the idea to
implement the wait just with flush_work(), and gets rid of the extra
smc_close_wait_listen_clcsock() function.

Fixes: 127f4970 ("net/smc: release clcsock from tcp_listen_worker")
Reported-by: Hans Wippel <hwippel@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

3d502067

14 Mar, 2018 12 commits

sunvnet: does not support GSO for sctp · cf55612a

Cathy Zhou authored Mar 14, 2018

The NETIF_F_GSO_SOFTWARE implies support for GSO on SCTP, but the
sunvnet driver does not support GSO for sctp.  Here we remove the
NETIF_F_GSO_SOFTWARE feature flag and only report NETIF_F_ALL_TSO
instead.
Signed-off-by: Cathy Zhou <Cathy.Zhou@Oracle.COM>
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cf55612a

Merge tag 'linux-can-fixes-for-4.16-20180314' of... · 4ea41f82

David S. Miller authored Mar 14, 2018

Merge tag 'linux-can-fixes-for-4.16-20180314' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can

Marc Kleine-Budde says:

====================
pull-request: can 2018-03-14

this is a pull request of two patches for net/master.

Both patches are by Andri Yngvason and fix problems in the cc770 driver,
that show up quite fast on RT systems, but also on non RT setups.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

4ea41f82

tg3: prevent scheduling while atomic splat · ea91df6d

Jonathan Toppins authored Mar 14, 2018

The problem was introduced in commit
506b0a39 ("[netdrv] tg3: APE heartbeat changes"). The bug occurs
because tp->lock spinlock is held which is obtained in tg3_start
by way of tg3_full_lock(), line 11571. The documentation for usleep_range()
specifically states it cannot be used inside a spinlock.

Fixes: 506b0a39 ("[netdrv] tg3: APE heartbeat changes")
Signed-off-by: Jonathan Toppins <jtoppins@redhat.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ea91df6d

ipv4: lock mtu in fnhe when received PMTU < net.ipv4.route.min_pmtu · d52e5a7e

Sabrina Dubroca authored Mar 14, 2018

Prior to the rework of PMTU information storage in commit
2c8cec5c ("ipv4: Cache learned PMTU information in inetpeer."),
when a PMTU event advertising a PMTU smaller than
net.ipv4.route.min_pmtu was received, we would disable setting the DF
flag on packets by locking the MTU metric, and set the PMTU to
net.ipv4.route.min_pmtu.

Since then, we don't disable DF, and set PMTU to
net.ipv4.route.min_pmtu, so the intermediate router that has this link
with a small MTU will have to drop the packets.

This patch reestablishes pre-2.6.39 behavior by splitting
rtable->rt_pmtu into a bitfield with rt_mtu_locked and rt_pmtu.
rt_mtu_locked indicates that we shouldn't set the DF bit on that path,
and is checked in ip_dont_fragment().

One possible workaround is to set net.ipv4.route.min_pmtu to a value low
enough to accommodate the lowest MTU encountered.

Fixes: 2c8cec5c ("ipv4: Cache learned PMTU information in inetpeer.")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

d52e5a7e

Merge branch 'DPAA-Ethernet-fixes' · 16c2e4db

David S. Miller authored Mar 14, 2018

Madalin Bucur says:

====================
DPAA Ethernet fixes

This patch set is addressing several issues in the DPAA Ethernet
driver suite:

 - module unload crash caused by wrong reference to device being left
   in the cleanup code after the DSA related changes
 - scheduling wile atomic bug in QMan code revealed during dpaa_eth
   module unload
 - a couple of error counter fixes, a duplicated init in dpaa_eth.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

16c2e4db

dpaa_eth: remove duplicate increment of the tx_errors counter · 82d141cd

Camelia Groza authored Mar 14, 2018

The tx_errors counter is incremented by the dpaa_xmit caller.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

82d141cd

dpaa_eth: increment the RX dropped counter when needed · e4d1b37c

Camelia Groza authored Mar 14, 2018

Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e4d1b37c

dpaa_eth: remove duplicate initialization · 56518636

Camelia Groza authored Mar 14, 2018

The fd_format has already been initialized at this point.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

56518636

dpaa_eth: fix error in dpaa_remove() · 88075256

Madalin Bucur authored Mar 14, 2018

The recent changes that make the driver probing compatible with DSA
were not propagated in the dpa_remove() function, breaking the
module unload function. Using the proper device to address the issue.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

88075256

soc/fsl/qbman: fix issue in qman_delete_cgr_safe() · 96f413f4

Madalin Bucur authored Mar 14, 2018

The wait_for_completion() call in qman_delete_cgr_safe()
was triggering a scheduling while atomic bug, replacing the
kthread with a smp_call_function_single() call to fix it.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

96f413f4

net: use skb_to_full_sk() in skb_update_prio() · 4dcb31d4

Eric Dumazet authored Mar 14, 2018

Andrei Vagin reported a KASAN: slab-out-of-bounds error in
skb_update_prio()

Since SYNACK might be attached to a request socket, we need to
get back to the listener socket.
Since this listener is manipulated without locks, add const
qualifiers to sock_cgroup_prioidx() so that the const can also
be used in skb_update_prio()

Also add the const qualifier to sock_cgroup_classid() for consistency.

Fixes: ca6fb065 ("tcp: attach SYNACK messages to request sockets instead of listener")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrei Vagin <avagin@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

4dcb31d4

can: cc770: Fix queue stall & dropped RTR reply · 74620123

Andri Yngvason authored Mar 14, 2018

While waiting for the TX object to send an RTR, an external message with a
matching id can overwrite the TX data. In this case we must call the rx
routine and then try transmitting the message that was overwritten again.

The queue was being stalled because the RX event did not generate an
interrupt to wake up the queue again and the TX event did not happen
because the TXRQST flag is reset by the chip when new data is received.

According to the CC770 datasheet the id of a message object should not be
changed while the MSGVAL bit is set. This has been fixed by resetting the
MSGVAL bit before modifying the object in the transmit function and setting
it after. It is not enough to set & reset CPUUPD.

It is important to keep the MSGVAL bit reset while the message object is
being modified. Otherwise, during RTR transmission, a frame with matching
id could trigger an rx-interrupt, which would cause a race condition
between the interrupt routine and the transmit function.
Signed-off-by: Andri Yngvason <andri.yngvason@marel.com>
Tested-by: Richard Weinberger <richard@nod.at>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

74620123