- 13 Mar, 2018 5 commits
-
-
Dhinakaran Pandiyan authored
DRM_IOCTL_MODE_CURSOR results in frontbuffer flush before the cursor plane MMIOs are written to. But this flush should not be necessary for PSR as hardware tracking triggers PSR exit when MMIOs are written. As for FBC, the spec says "Flips or changes to plane size and panning" cause FBC to be nuked. Use origin == ORIGIN_FLIP so that features can ignore cursor updates in their frontbuffer_flush implementations. /sys/kernel/debug/dri/0/i915_fbc_status shows "Compressing: yes" when I move the cursor around. v3: Use ORIGIN_FLIP now that pin_to_display does not flush frontbuffer. v2: Update comment in i915_gem_object_pin_to_display_plane. (Chris) Cc: Paulo Zanoni <paulo.r.zanoni@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by:
Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com> Reviewed-by:
Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by:
-
Dhinakaran Pandiyan authored
i915_gem_obj_pin_to_display() calls frontbuffer_flush with origin set to DIRTYFB. The callers however are at a vantage point to decide if hardware frontbuffer tracking can do the flush for us. For example, legacy cursor updates, like flips, write to MMIO registers, which then triggers PSR flush by the hardware. Moving frontbuffer_flush out will enable us to skip a software initiated flush by setting origin to FLIP. Thanks to Chris for the idea. v2: Rebased due to Ville adding intel_plane_pin_fb(). Minor code reordering as fb_obj_flush doesn't need struct_mutex (Chris) Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by:
-
Chris Wilson authored
eu_regs[] is written 2*max_slices times (like s_reg[]) but oddly read 2*max_slices + max_subslices/2 times. Allocate the array large enough for the writes to avoid overwriting our stack and worry about the logic later. Fixes: 7aa0b14e ("drm/i915: Remove variable length arrays from sseu debugfs printers") Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105479Signed-off-by:
Chris Wilson <chris@chris-wilson.co.uk> Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: Matthew Auld <matthew.auld@intel.com> Reviewed-by:
Lionel Landwerlin <lionel.g.landwerlin@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180313113149.1094-1-chris@chris-wilson.co.uk
-
Chris Wilson authored
VLA are strongly discouraged in the kernel due to ambiguity they impose on the limited stack space and security concerns over manipulating the stack frame. Add -Wvla to our compiler flags so that CI rejects them. Signed-off-by:
Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180313004055.25411-2-chris@chris-wilson.co.uk
-
Chris Wilson authored
In order to enable -Wvla to prevent new variable length arrays being used in i915.ko, we first must remove the existing VLA. Inside i915_print_sseu_info(), VLA are used as the actual size of the sseu depends on platform. Replace the VLA with the maximum required. Signed-off-by:
Tvrtko Ursulin <tvrtko.ursulin@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180313004055.25411-1-chris@chris-wilson.co.uk
-
- 12 Mar, 2018 4 commits
-
-
Michal Wajdeczko authored
Instead of dancing around uC on reset/suspend/resume scenarios, explicitly sanitize uC when we sanitize GEM to force uC reload and start from known beginning. v2: don't forget about reset path (Daniele) sanitize uc before gem initiated full reset (Daniele) v3: drop redundant disable_communication in init_hw (Daniele) Signed-off-by:Michal Wajdeczko <michal.wajdeczko@intel.com> Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Michel Thierry <michel.thierry@intel.com> Reviewed-by:
Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Signed-off-by:
-
Michal Wajdeczko authored
We are sanitizing uC related modparams together with other driver modparams in intel_sanitize_options called from i915_driver_init_hw, but this is too late for us as we will want to use USES_GUC/USES_HUC macros at earlier stage. Since our sanitizing does not require any MMIO access, we can do it in intel_uc_init_early right after we resolve firmware names. Signed-off-by:
-
Chris Wilson authored
There is some redundancy between dma_fence->ops->enable_signaling (via i915_fence_enable_signaling) and our backend, intel_engine_enable_signaling() in that both levels recheck the fence status multiple times. If we convert intel_engine_enable_signaling() to return the information desired by dma_fence->ops->enable_signaling, we can reduce i915_fence_enable_signaling to a simple stub and avoid trying to reinterpret the same information. Signed-off-by:
-
Rodrigo Vivi authored
WA 0884:bxt:all,cnl:*:A - "When FBC is enabled with eDP PSR, the CPU host modify writes may not get updated on the Display as expected. WA: Write 0x00000000 to CUR_SURFLIVE_A with every CPU host modify write to trigger PSR exit." We can also find on spec other cases where they describe bogus writes to cursor registers to force PSR exit with HW tracking. And it was confirmed by HW engineers that this Wa can be safely applied for any frontbuffer activity. So let's use this more and more here instead of forcibly disable and re-enable PSR everytime that we have a simple reliable flush case. Other commits improve the fbcon/fbdev use a lot, but this approach is the only when where we can get a fully reliable console with no slowness or missed frames and PSR still enabled and active. v2: - Rebase on drm-tip - (DK) Add a comment to explain that WA tells about writing 0 to CUR_SURFLIVE_A but we write to CUR_SURFLIVE(pipe). v3: Wa doesn't work on PSR2. Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com> Signed-off-by:
-
- 09 Mar, 2018 15 commits
-
-
Michal Wajdeczko authored
Error state management code was moved into separate .c unit but we didn't move related definitions into own header. v2: move also intel_display_error_state forward decl fix ("Prefer 'unsigned int' to bare use of 'unsigned'") warnings detected by checkpatch in moved code (Michal) Signed-off-by: -
Michal Wajdeczko authored
Definitions in i915_pmu.h header depend on other types and declarations that were not explicitly included. Fix that by adding related headers and forward declarations. While here, change license text to SPDX format. v2: don't drop "intel_ringbuffer.h" (Tvrtko) Signed-off-by:
-
Michal Wajdeczko authored
Function i915_gem_batch_pool_init() failed to follow obj-verb naming schema. Fix that by swapping function parameters. While here, change license text to SPDX format. v2: use intel_engine_init_batch_pool (Chris) as proxy (Michal) Signed-off-by:
-
Michal Wajdeczko authored
Header intel_ringbuffer.h is using definitions from i915_reg.h but forget to include it. Remove this hidden dependency by explicitly include missing header. v2: add reminder (Chris) Signed-off-by:
-
Michal Wajdeczko authored
To allow future code reuse. While here, fix comment style. v2: Notifications are a separate thing - rename the handler (Sagar) Suggested-by:
Oscar Mateo <oscar.mateo@intel.com> Signed-off-by:
Michał Winiarski <michal.winiarski@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Cc: Oscar Mateo <oscar.mateo@intel.com> Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com> Reviewed-by:
Sagar Arun Kamble <sagar.a.kamble@intel.com> Signed-off-by:
-
Michał Winiarski authored
We have many functions responsible for allocating different parts of GuC log runtime called from multiple places. Let's stick with keeping everything in guc_log_register instead. v2: Use more generic intel_uc_register name, keep using "misc" suffix (Michał) s/dev_priv/i915 (Sagar) Make guc_log_relay_* static (sparse) Signed-off-by: -
Michał Winiarski authored
We plan to decouple log runtime (mapping + relay) from verbosity control. Let's tidy the code now to reduce the churn in the following patches. v2: Tidy macros, keep debug messages, use helper var for enable, correct typo (Michał) Fix incorrect input validaction (Sagar) Signed-off-by: -
Lyude Paul authored
Signed-off-by:
Lyude Paul <lyude@redhat.com> Cc: Manasi Navare <manasi.d.navare@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by:
Manasi Navare <manasi.d.navare@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180308232421.14049-2-lyude@redhat.com
-
Chris Wilson authored
tasklet_kill() will spin waiting for the current tasklet to be executed. However, if tasklet_disable() has been called, then the tasklet is never executed but permanently put back onto the runlist until tasklet_enable() is called. Ergo, we cannot use tasklet_kill() inside a disable/enable pair. This is the case when we call set-wedge from inside i915_reset(), and another request was submitted to us concurrent to the reset. Fixes: 963ddd63 ("drm/i915: Suspend submission tasklets around wedging") Signed-off-by:
Mika Kuoppala <mika.kuoppala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180307134226.25492-6-chris@chris-wilson.co.uk
-
Chris Wilson authored
Similar to the staging around handling of engine->submit_request, we need to stop adding to the execlists->queue prior to calling engine->cancel_requests. cancel_requests will move requests from the queue onto the timeline, so if we add a request onto the queue after that point, it will be lost. Fixes: af7a8ffa ("drm/i915: Use rcu instead of stop_machine in set_wedged") Signed-off-by:
-
Chris Wilson authored
Include ring->emit and ring->space alongside ring->(head,tail) when printing debug information. Signed-off-by:
-
Chris Wilson authored
When wedged, we do not update the ring->tail as we submit the requests causing us to leak the ring->space upon cleaning up the wedged driver. We can just use the value stored in rq->tail, and keep the submission backend details away from set-wedge. Signed-off-by:
-
Chris Wilson authored
Before we reset the GPU after marking the device as wedged, we wait for all the remaining requests to be completed (and marked as EIO). Afterwards, we should flush the request lists so the next batch start with the driver in an idle state. Signed-off-by:
-
Jani Nikula authored
We don't want to preserve the DDI A 4 lane bit on ICL. Fixes: 3d2011cf ("drm/i915/icl: remove port A/E lane sharing limitation.") Cc: Mahesh Kumar <mahesh1.kumar@intel.com> Cc: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by:
-
Chris Wilson authored
Originally we were inlining gen8_cs_irq_handler() and so expected the compiler to constant-fold away the irq_shift (so we had hardcoded it as opposed to use engine->irq_shift). However, we dropped the inline given the proliferation of gen8_cs_irq_handler()s. If we pull the shifting of the iir into the caller, we can shrink the code still further: add/remove: 0/0 grow/shrink: 0/3 up/down: 0/-34 (-34) Function old new delta gen8_cs_irq_handler 123 118 -5 gen8_gt_irq_handler 261 248 -13 gen11_irq_handler 722 706 -16 v2: Drop gen11_cs_irq_handler now that it is a simple stub around gen8_cs_irq_handler (Daniele) References: 5d3d69d5 ("drm/i915: Stop inlining the execlists IRQ handler") Signed-off-by:
-
- 08 Mar, 2018 14 commits
-
-
Chris Wilson authored
When reporting the frequency table stored in the punit, report the full range and not just the user restricted frequency range. In the process keep the code to set the frequency table and read it the same. v3: As we haven't separated the sb_lock from the pcu_lock yet, there's a cycle between the pcu_lock and intel_runtime_pm_get. References: f936ec34 ("drm/i915/skl: Updated the i915_ring_freq_table debugfs function") Signed-off-by:
-
Chris Wilson authored
The boost frequency is only applied from the RPS worker while someone is waiting on a request and requested a boost. As such, when the user wishes to change the frequency, we have to kick the worker in order to re-evaluate whether to apply the boost frequency. v2: Check num_waiters to decide if we should kick the worker to handle boosting. Fixes: 29ecd78d ("drm/i915: Define a separate variable and control for RPS waitboost frequency") Signed-off-by:
Mika Kuoppala <mika.kuoppala@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180308142648.4016-1-chris@chris-wilson.co.uk
-
Maarten Lankhorst authored
This will get rid of the following error: [ 74.730271] WARNING: CPU: 4 PID: 0 at drivers/gpu/drm/drm_vblank.c:614 drm_calc_vbltimestamp_from_scanoutpos+0x13e/0x2f0 [ 74.730311] Modules linked in: vgem snd_hda_codec_hdmi snd_hda_codec_realtek snd_hda_codec_generic i915 x86_pkg_temp_thermal intel_powerclamp coretemp snd_hda_intel crct10dif_pclmul snd_hda_codec crc32_pclmul snd_hwdep broadcom ghash_clmulni_intel snd_hda_core bcm_phy_lib snd_pcm tg3 lpc_ich mei_me mei prime_numbers [ 74.730353] CPU: 4 PID: 0 Comm: swapper/4 Tainted: G U 4.16.0-rc2-CI-CI_DRM_3822+ #1 [ 74.730355] Hardware name: Dell Inc. XPS 8300 /0Y2MRG, BIOS A06 10/17/2011 [ 74.730359] RIP: 0010:drm_calc_vbltimestamp_from_scanoutpos+0x13e/0x2f0 [ 74.730361] RSP: 0018:ffff88022fb03d10 EFLAGS: 00010086 [ 74.730365] RAX: ffffffffa0291d20 RBX: ffff88021a180000 RCX: 0000000000000001 [ 74.730367] RDX: ffffffff820e7db8 RSI: 0000000000000001 RDI: ffffffff82068cea [ 74.730369] RBP: ffff88022fb03d70 R08: 0000000000000000 R09: ffffffff815d26d0 [ 74.730371] R10: 0000000000000000 R11: ffffffffa0161ca0 R12: 0000000000000001 [ 74.730373] R13: ffff880212448008 R14: ffff880212448330 R15: 0000000000000000 [ 74.730376] FS: 0000000000000000(0000) GS:ffff88022fb00000(0000) knlGS:0000000000000000 [ 74.730378] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 74.730380] CR2: 000055edcbec9000 CR3: 0000000002210001 CR4: 00000000000606e0 [ 74.730382] Call Trace: [ 74.730385] <IRQ> [ 74.730397] drm_get_last_vbltimestamp+0x36/0x50 [ 74.730401] drm_update_vblank_count+0x64/0x240 [ 74.730409] drm_crtc_accurate_vblank_count+0x41/0x90 [ 74.730453] display_pipe_crc_irq_handler+0x176/0x220 [i915] [ 74.730497] i9xx_pipe_crc_irq_handler+0xfe/0x150 [i915] [ 74.730537] ironlake_irq_handler+0x618/0xa30 [i915] [ 74.730548] __handle_irq_event_percpu+0x3c/0x340 [ 74.730556] handle_irq_event_percpu+0x1b/0x50 [ 74.730561] handle_irq_event+0x2f/0x50 [ 74.730566] handle_edge_irq+0xe4/0x1b0 [ 74.730572] handle_irq+0x11/0x20 [ 74.730576] do_IRQ+0x5e/0x120 [ 74.730584] common_interrupt+0x84/0x84 [ 74.730586] </IRQ> [ 74.730591] RIP: 0010:cpuidle_enter_state+0xaa/0x350 [ 74.730593] RSP: 0018:ffffc9000008beb8 EFLAGS: 00000212 ORIG_RAX: ffffffffffffffde [ 74.730597] RAX: ffff880226b80040 RBX: 000000000031fc3e RCX: 0000000000000001 [ 74.730599] RDX: 0000000000000000 RSI: ffffffff8210fb59 RDI: ffffffff820c02e7 [ 74.730601] RBP: 0000000000000004 R08: 00000000000040af R09: 0000000000000018 [ 74.730603] R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000004 [ 74.730606] R13: ffffe8ffffd00430 R14: 0000001166120bf4 R15: ffffffff82294460 [ 74.730621] ? cpuidle_enter_state+0xa6/0x350 [ 74.730629] do_idle+0x188/0x1d0 [ 74.730636] cpu_startup_entry+0x14/0x20 [ 74.730641] start_secondary+0x129/0x160 [ 74.730646] secondary_startup_64+0xa5/0xb0 [ 74.730660] Code: e1 48 c7 c2 b8 7d 0e 82 be 01 00 00 00 48 c7 c7 ea 8c 06 82 e8 64 ec ff ff 48 8b 83 c8 07 00 00 48 83 78 28 00 0f 84 e2 fe ff ff <0f> 0b 45 31 ed e9 db fe ff ff 41 b8 d3 4d 62 10 89 c8 6a 03 41 [ 74.730754] ---[ end trace 14b1345705b68565 ]--- Changes since v1: - Don't try to apply CRC workaround when enabling pipe, it should already be enabled. Changes since v2: - Make crc functions for !DEBUGFS case inline. - Pass intel_crtc to crc functions. - Add comments to callsites. Changes since v3: - Cache selected source to pipe_crc->source. - Set pipe_crc->skipped to MIN_INT during disable to close a race condition. Changes since v4: - Handle fallout from setting pipe_crc->source in irq handler. Cc: Marta Löfstedt <marta.lofstedt@intel.com> Reported-by:
Marta Löfstedt <marta.lofstedt@intel.com> Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105185Signed-off-by:
Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180308120202.52446-1-maarten.lankhorst@linux.intel.comReviewed-by:
-
Chris Wilson authored
Currently, we only allow ourselves to prune the fences so long as all the waits completed (i.e. all the fences we checked were signaled), and that the reservation snapshot did not change across the wait. However, if we only waited for a subset of the reservation object, i.e. just waiting for the last writer to complete as opposed to all readers as well, then we would erroneously conclude we could prune the fences as indeed although all of our waits were successful, they did not represent the totality of the reservation object. v2: We only need to check the shared fences due to construction (i.e. all of the shared fences will be later than the exclusive fence, if any). Fixes: e54ca977 ("drm/i915: Remove completed fences after a wait") Signed-off-by:
Matthew Auld <matthew.auld@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180307171303.29466-1-chris@chris-wilson.co.uk
-
Joonas Lahtinen authored
Signed-off-by:Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
-
https://github.com/intel/gvt-linuxJoonas Lahtinen authored
gvt-next-2018-03-08 - big refactor for shadow ppgtt (Changbin) - KBL context save/restore via LRI cmd (Weinan) - misc smatch fixes (Zhenyu) - Properly unmap dma for guest page (Changbin) - other misc fixes (Xiong, etc.) Signed-off-by:
-
Weinan Li authored
There is one corner case missing schedule out notification of the preempted request. The preempted request is just completed when preemption happen, then it will be canceled and won't be resubmitted later, GVT-g will lost the schedule out notification. Here add schedule out notification if found the preempted request has been completed. v2: - refine description, add completed check and notification in execlists_cancel_port_requests. (Chris) v3: - use ternary confitional, remove local variable. (Tvrtko) Cc: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by:
Weinan Li <weinan.z.li@intel.com> Signed-off-by:
Zhenyu Wang <zhenyuw@linux.intel.com> Reviewed-by:
-
Lionel Landwerlin authored
With the introduction of asymmetric slices in CNL, we cannot rely on the previous SUBSLICE_MASK getparam to tell userspace what subslices are available. Here we introduce a more detailed way of querying the Gen's GPU topology that doesn't aggregate numbers. This is essential for monitoring parts of the GPU with the OA unit, because counters need to be normalized to the number of EUs/subslices/slices. The current aggregated numbers like EU_TOTAL do not gives us sufficient information. The Mesa series making use of this API is : https://patchwork.freedesktop.org/series/38795/ As a bonus we can draw representations of the GPU : https://imgur.com/a/vuqpa v2: Rename uapi struct s/_mask/_info/ (Tvrtko) Report max_slice/subslice/eus_per_subslice rather than strides (Tvrtko) Add uapi macros to read data from *_info structs (Tvrtko) v3: Use !!(v & DRM_I915_BIT()) for uapi macros instead of custom shifts (Tvrtko) v4: factorize query item writting (Tvrtko) tweak uapi struct/define names (Tvrtko) v5: Replace ALIGN() macro (Chris) v6: Updated uapi comments (Tvrtko) Moved flags != 0 checks into vfuncs (Tvrtko) v7: Use access_ok() before copying anything, to avoid overflows (Chris) Switch BUG_ON() to GEM_WARN_ON() (Tvrtko) v8: Tweak uapi comments style to match the coding style (Lionel) v9: Fix error in comment about computation of enabled subslice (Tvrtko) v10: Fix/update comments in uAPI (Sagar) v11: Drop drm_i915_query_(slice|subslice|eu)_info in favor of a single drm_i915_query_topology_info (Joonas) v12: Add subslice_stride/eu_stride in drm_i915_query_topology_info (Joonas) v13: Fix comment in uAPI (Joonas) Signed-off-by: -
Lionel Landwerlin authored
There are a number of information that are readable from hardware registers and that we would like to make accessible to userspace. One particular example is the topology of the execution units (how are execution units grouped in subslices and slices and also which ones have been fused off for die recovery). At the moment the GET_PARAM ioctl covers some basic needs, but generally is only able to return a single value for each defined parameter. This is a bit problematic with topology descriptions which are array/maps of available units. This change introduces a new ioctl that can deal with requests to fill structures of potentially variable lengths. The user is expected fill a query with length fields set at 0 on the first call, the kernel then sets the length fields to the their expected values. A second call to the kernel with length fields at their expected values will trigger a copy of the data to the pointed memory locations. The scope of this uAPI is only to provide information to userspace, not to allow configuration of the device. v2: Simplify dispatcher code iteration (Tvrtko) Tweak uapi drm_i915_query_item structure (Tvrtko) v3: Rename pad fields into flags (Chris) Return error on flags field != 0 (Chris) Only copy length back to userspace in drm_i915_query_item (Chris) v4: Use array of functions instead of switch (Chris) v5: More comments in uapi (Tvrtko) Return query item errors in length field (All) v6: Tweak uapi comments style to match the coding style (Lionel) v7: Add i915_query.h (Joonas) v8: (Lionel) Change the behavior of the item iterator to report invalid queries into the query item rather than stopping the iteration. This enables userspace applications to query newer items on older kernels and only have failure on the items that are not supported. v9: Edit copyright headers (Joonas) v10: Typos & comments in uapi (Joonas) Signed-off-by: -
Lionel Landwerlin authored
This might be useful information for developers looking at an error state. v2: Place topology towards the end of the error state (Chris) v3: Reuse common printing code (Michal) v4: Make this a one-liner (Chris) Signed-off-by:
-
Lionel Landwerlin authored
While the end goal is to make this information available to userspace through a new ioctl, there is no reason we can't display it in a human readable fashion through debugfs. slice0: 3 subslice(s) (0x7): subslice0: 8 EUs (0xff) subslice1: 8 EUs (0xff) subslice2: 8 EUs (0xff) subslice3: 0 EUs (0x0) slice1: 3 subslice(s) (0x7): subslice0: 8 EUs (0xff) subslice1: 8 EUs (0xff) subslice2: 8 EUs (0xff) subslice3: 0 EUs (0x0) slice2: 3 subslice(s) (0x7): subslice0: 8 EUs (0xff) subslice1: 8 EUs (0xff) subslice2: 8 EUs (0xff) subslice3: 0 EUs (0x0) v2: Reformat debugfs printing (Tvrtko) Use the new EU mask helper (Tvrtko) v3: Move printing code to intel_device_info.c to be shared with error state (Michal) v4: Bump u8 to u16 when using sseu_get_eus() (Lionel) Suggested-by: -
Lionel Landwerlin authored
Now that we have that information in topology fields, let's just reuse it. v2: Style tweaks (Tvrtko) Signed-off-by:
-
Lionel Landwerlin authored
Up to now, subslice mask was assumed to be uniform across slices. But starting with Cannonlake, slices can be asymmetric (for example slice0 has different number of subslices as slice1+). This change stores all subslices masks for all slices rather than having a single mask that applies to all slices. v2: Rework how we store total numbers in sseu_dev_info (Tvrtko) Fix CHV eu masks, was reading disabled as enabled (Tvrtko) Readability changes (Tvrtko) Add EU index helper (Tvrtko) v3: Turn ALIGN(v, 8) / 8 into DIV_ROUND_UP(v, BITS_PER_BYTE) (Tvrtko) Reuse sseu_eu_idx() for setting eu_mask on CHV (Tvrtko) Reformat debug prints for subslices (Tvrtko) v4: Change eu_mask helper into sseu_set_eus() (Tvrtko) v5: With Haswell reporting masks & counts, bump sseu_*_eus() functions to use u16 (Lionel) v6: Fix sseu_get_eus() for > 8 EUs per subslice (Lionel) v7: Change debugfs enabels for number of subslices per slice, will need a small igt/pm_sseu change (Lionel) Drop subslice_total field from sseu_dev_info, rely on sseu_subslice_total() to recompute the value instead (Lionel) v8: Remove unused function compute_subslice_total() (Lionel) Signed-off-by: -
Andrew Morton authored
gcc-4.4.4 has problems with initalizers of anon unions. drivers/gpu/drm/i915/intel_guc_log.c: In function 'guc_log_control': drivers/gpu/drm/i915/intel_guc_log.c:64: error: unknown field 'logging_enabled' specified in initializer Work around this. Fixes: 35fe703c ("drm/i915/guc: Change values for i915_guc_log_control") Cc: Michal Wajdeczko <michal.wajdeczko@intel.com> Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com> Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
- 07 Mar, 2018 2 commits
-
-
Rodrigo Vivi authored
"Clock gating bug in GWL may not clear barrier state when an EOT is received, causing a hang the next time that barrier is used." HSDES: 2201832410 Cc: Rafael Antognolli <rafael.antognolli@intel.com> Signed-off-by:
Rafael Antognolli <rafael.antognolli@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180307220912.3681-1-rodrigo.vivi@intel.com
-
Daniele Ceraolo Spurio authored
The main difference with previous GENs is that starting from Gen11 each VCS and VECS engine has its own power well, which only exist if the related engine exists in the HW. The fallback forcewake request workaround is only needed on gen9 according to the HSDES WA entry (1604254524), so we can go back to using the simpler fw_domains_get/put functions. BSpec: 18331 v2: fix fwtable, use array to test shadow tables, create new accessors to avoid check on every access (Tvrtko) v3 (from Paulo): Rebase. v4: - Range 09400-097FF should be FORCEWAKE_ALL (Daniele) - Use the BIT macro for forcewake domains (Daniele) - Add a comment about the range ordering (Oscar) - Updated commit message (Oscar) v5: Rebased v6: Use I915_MAX_VCS/VECS (Michal) v7: translate FORCEWAKE_ALL to available domains v8: rebase, add clarification on fallback ack in commit message. v9: fix rebase issue, change check in fw_domains_init from IS_GEN11 to GEN >= 11 v10: Generate is_genX_shadowed with a macro (Daniele) Include gen11_fw_ranges in the selftest (Michel) v11: Simplify FORCEWAKE_ALL, new line between NEEDS_FORCEWAKEs (Tvrtko) Cc: Michal Wajdeczko <michal.wajdeczko@intel.com> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: Paulo Zanoni <paulo.r.zanoni@intel.com> Acked-by:Michel Thierry <michel.thierry@intel.com> Signed-off-by:
-
