- 23 Nov, 2014 40 commits
-
-
Hans de Goede authored
The Mele M9 / A1000G quad has a blue status led, add support for this. Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
Maxime Ripard <maxime.ripard@free-electrons.com>
-
Hans de Goede authored
The Mele M9 / A1000G quad uses both usb-ports, one goes to an internal usb wifi card, the other to a build-in usb-hub, so neither need their OHCI companion controller to be enabled since the are always connected at USB-2 speeds. The controller which is attached to the wifi also does not need a vbus regulator. Signed-off-by:
-
Hans de Goede authored
This avoids it getting briefly turned off between when the regulator getting registered and the ahci driver turning it back on, thus avoiding the disk going into emergency head park mode. Reported-by:
Bruno Prémont <bonbons@linux-vserver.org> Tested-by:
-
Roman Byshko authored
Signed-off-by:
Roman Byshko <rbyshko@gmail.com> Signed-off-by:
-
Roman Byshko authored
Cubietruck uses different pin for the USB OTG VBUS that is why we override the one defined in sunxi-common-regulators.dtsi Signed-off-by:
-
Roman Byshko authored
Signed-off-by:
-
Roman Byshko authored
Until now the regulator nodes for powering USB VBUS existed only for the two host controllers. Now the regulator is added for USB OTG too. Signed-off-by:
-
Karsten Merker authored
On the LeMaker Banana Pi, probing the external ethernet PHY connected to the SoC's internal GMAC module sometimes fails. The PHY power supply is handled via a GPIO-controlled regulator, and the existing regulator startup-delay of 50000us is too short to make sure that the PHY is always fully powered up when it is queried by phylib. Tests have shown that to provide a reliable PHY detection, the startup-delay has to be increased to at least 60000us. To have a certain safety margin and to cater for manufacturing variations between different boards, the delay gets set to 100000us as discussed on the linux-arm-kernel mailinglist. Signed-off-by:
Karsten Merker <merker@debian.org> Acked-by:
-
Maxime Ripard authored
The current GPL only licensing on the DTSI makes it very impractical for other software components licensed under another license. In order to make it easier for them to reuse our device trees, relicense our device trees under a GPL/X11 dual-license. Signed-off-by:
Olof Johansson <olof@lixom.net> Acked-by:
-
Maxime Ripard authored
The current GPL only licensing on the DTSI makes it very impractical for other software components licensed under another license. In order to make it easier for them to reuse our device trees, relicense our device trees under a GPL/X11 dual-license. Signed-off-by:
Carlo Caione <carlo@caione.org> Acked-by:
Emilio López <emilio@elopez.com.ar> Acked-by:
Olliver Schinagl <oliver@schinagl.nl> Acked-by:
Stefan Roese <sr@denx.de>
-
Maxime Ripard authored
The current GPL only licensing on the DTSI makes it very impractical for other software components licensed under another license. In order to make it easier for them to reuse our device trees, relicense our device trees under a GPL/X11 dual-license. Signed-off-by:
Zoltan HERPAI <wigyori@uid0.hu>
-
Maxime Ripard authored
The current GPL only licensing on the DTSI makes it very impractical for other software components licensed under another license. In order to make it easier for them to reuse our device trees, relicense our device trees under a GPL/X11 dual-license. Signed-off-by:
-
Maxime Ripard authored
The current GPL only licensing on the DTSI makes it very impractical for other software components licensed under another license. In order to make it easier for them to reuse our device trees, relicense our device trees under a GPL/X11 dual-license. Signed-off-by:
FUKAUMI Naoki <naobsd@gmail.com>
-
Chen-Yu Tsai authored
The A80 Optimus board exposes uart4 on the GPIO expansion header. Enable it so we can use it. Also enable the internal pull-ups, as there doesn't seem to be external pull-up resistors for pins on the expansion header. Signed-off-by:
Chen-Yu Tsai <wens@csie.org> Signed-off-by:
-
Chen-Yu Tsai authored
uart4 only has one possible pinmux setting on the A80 SoC. Signed-off-by:
-
Chen-Yu Tsai authored
The A80 Optimus board has 3 usable LEDs that are controlled via GPIO. This patch adds support for 2 of them which are driver by GPIOs in the main pin controller. The remaining one uses GPIO from the R_PIO controller, which we don't support yet. Signed-off-by:
-
Chen-Yu Tsai authored
i2c3 is exposed on the GPIO extension header. Enable it so we can use it. Also enable internal pull-ups on the pins, as they don't seem to have external pull-up resistors. Signed-off-by:
-
Chen-Yu Tsai authored
i2c3 has only one possible pinmux setting on the A80 SoC. Signed-off-by:
-
Chen-Yu Tsai authored
The A80 has 5 i2c controllers in the main processor block. Signed-off-by:
-
Maxime Ripard authored
Enable the UART0 muxing, as set up by the bootloader. Signed-off-by:
Linus Walleij <linus.walleij@linaro.org>
-
Maxime Ripard authored
The A80 pinctrl driver is just as usual our pinctrl/gpio/external interrupt controller. Nothing really out of the extraordinary here... Signed-off-by:
-
Maxime Ripard authored
The current GPL only licensing on the DTSI makes it very impractical for other software components licensed under another license. In order to make it easier for them to reuse our device trees, relicense our device trees under a GPL/X11 dual-license. Signed-off-by:
-
Maxime Ripard authored
During the GPL to GPL/X11 licensing migration, the GPL notice introduced mentionned the device trees as a library, which is not really accurate. It began to spread by copy and paste. Fix all these library mentions to reflect the file that it's actually just a file. Signed-off-by: -
Maxime Ripard authored
The current GPL only licensing on the DTSI makes it very impractical for other software components licensed under another license. In order to make it easier for them to reuse our device trees, relicense our device trees under a GPL/X11 dual-license. Signed-off-by:
Boris BREZILLON <boris.brezillon@free-electrons.com>
-
Chen-Yu Tsai authored
Now that we have driver support for the basic clocks, add them to the dtsi and update existing peripherals. Also add reset controls to match. Signed-off-by:
-
Maxime Ripard authored
The current GPL only licensing on the DTSI makes it very impractical for other software components licensed under another license. In order to make it easier for them to reuse our device trees, relicense our device trees under a GPL/X11 dual-license. Signed-off-by:
-
Maxime Ripard authored
The current GPL only licensing on the DTSI makes it very impractical for other software components licensed under another license. In order to make it easier for them to reuse our device trees, relicense our device trees under a GPL/X11 dual-license. Signed-off-by:
-
Maxime Ripard authored
The current GPL only licensing on the DTSI makes it very impractical for other software components licensed under another license. In order to make it easier for them to reuse our device trees, relicense our device trees under a GPL/X11 dual-license. Signed-off-by:
-
Maxime Ripard authored
The current GPL only licensing on the DTSI makes it very impractical for other software components licensed under another license. In order to make it easier for them to reuse our device trees, relicense our device trees under a GPL/X11 dual-license. Signed-off-by: -
Maxime Ripard authored
The current GPL only licensing on the DTSI makes it very impractical for other software components licensed under another license. In order to make it easier for them to reuse our device trees, relicense our device trees under a GPL/X11 dual-license. Signed-off-by: -
Maxime Ripard authored
The current GPL only licensing on the DTSI makes it very impractical for other software components licensed under another license. In order to make it easier for them to reuse our device trees, relicense our device trees under a GPL/X11 dual-license. Signed-off-by:
-
Maxime Ripard authored
The current GPL only licensing on the DTSI makes it very impractical for other software components licensed under another license. In order to make it easier for them to reuse our device trees, relicense our device trees under a GPL/X11 dual-license. Signed-off-by:
-
Maxime Ripard authored
The current GPL only licensing on the DTSI makes it very impractical for other software components licensed under another license. In order to make it easier for them to reuse our device trees, relicense our device trees under a GPL/X11 dual-license. Signed-off-by:
-
Maxime Ripard authored
The current GPL only licensing on the DTSI makes it very impractical for other software components licensed under another license. In order to make it easier for them to reuse our device trees, relicense our device trees under a GPL/X11 dual-license. Signed-off-by:
-
Maxime Ripard authored
The current GPL only licensing on the DTSI makes it very impractical for other software components licensed under another license. In order to make it easier for them to reuse our device trees, relicense our device trees under a GPL/X11 dual-license. Signed-off-by:
-
Maxime Ripard authored
The current GPL only licensing on the DTSI makes it very impractical for other software components licensed under another license. In order to make it easier for them to reuse our device trees, relicense our device trees under a GPL/X11 dual-license. Signed-off-by:
David Lanzendörfer <david.lanzendoerfer@o2s.ch> Acked-by:
-
Maxime Ripard authored
The current GPL only licensing on the DTSI makes it very impractical for other software components licensed under another license. In order to make it easier for them to reuse our device trees, relicense our device trees under a GPL/X11 dual-license. Signed-off-by:
-
Maxime Ripard authored
The current GPL only licensing on the DTSI makes it very impractical for other software components licensed under another license. In order to make it easier for them to reuse our device trees, relicense our device trees under a GPL/X11 dual-license. Signed-off-by:
-
Maxime Ripard authored
The current GPL only licensing on the DTSI makes it very impractical for other software components licensed under another license. In order to make it easier for them to reuse our device trees, relicense our device trees under a GPL/X11 dual-license. Signed-off-by:
-
Chen-Yu Tsai authored
The A80 Optimus Board is was launched with the Allwinner A80 SoC. It was jointly developed by Allwinner and Merrii. This board has a UART port, a JTAG connector, USB host ports, a USB 3.0 OTG connector, an HDMI output, a micro SD slot, 8G NAND flash, 4G DRAM, a camera sensor interface, a WiFi/BT combo chip, a headphone jack, IR receiver, and additional GPIO headers. This patch adds only basic support. Signed-off-by:
Andreas Färber <afaerber@suse.de>
-
