- 28 Aug, 2018 39 commits
-
-
Jakub Kicinski authored
Add error prints to CPP target encoding/decoding logic, otherwise it's quite hard to pin point the reasons why read or write operations fail. Signed-off-by:
Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by:
Francois H. Theron <francois.theron@netronome.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Jakub Kicinski authored
We will soon need the MU locality field offset much more often than just for decoding MIP address. Save it in nfp_cpp for quick access. Note that we can already reuse the target config from nfp_cpp, no need to do the XPB read. Signed-off-by:
-
Jakub Kicinski authored
Use a switch statement instead of ifs for code dependent on chip version. While at it make sure we fail for unknown chip revisions. Signed-off-by:
-
Jakub Kicinski authored
Add NFP5000 to supported chips, the chip is backward compatible with NFP4000 and NFP6000, so core PCIe code needs to handle it the same way as 4k and 6k. Signed-off-by:
-
Jakub Kicinski authored
In multi-host scenarios Management FW may allocate MAC addresses at runtime, we have to use the indirect lookup to find them. Signed-off-by:
Dirk van der Merwe <dirk.vandermerwe@netronome.com> Signed-off-by:
-
Jakub Kicinski authored
Management FW can adjust some of the information in the HWinfo table at runtime. In some cases reading the table directly will not yield correct results. Add a NSP command for looking up information. Up until now we weren't making use of any of the values which may get adjusted. Signed-off-by:
-
Jakub Kicinski authored
To enable easier FW distribution NFP can now automatically select between FW stored on the flash and loaded from the kernel. If FW loading policy is set to auto it will compare the versions of FW from the host and from the flash and load the newer one. If FW type doesn't match (e.g. one advanced application vs another) the FW from the host takes precedence, unless one of them is the basic NIC firmware, in which case the non-basic-NIC FW is selected. This automatic selection mechanism requires we inform user what the verdict was. Print a message to the logs explaining the decision and the reason. Signed-off-by:
-
Jakub Kicinski authored
Flash may contain a default NFP application FW. This application can either be put there by the user (with ethtool -f) or shipped with the card. If file system FW is not found, attempt to load this flash stored app FW. Signed-off-by:
-
Jakub Kicinski authored
There is already a fair number of arguments to nfp_nsp_command() family of functions. Encapsulate them into structures to make adding new ones easier. No functional changes. Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queueDavid S. Miller authored
Jeff Kirsher says: ==================== 100GbE Intel Wired LAN Driver Updates 2018-08-28 This series contains new features and implementation updates for the ice driver. Anirudh reworks the current flex programming logic to add support for a second flex descriptor profile. Updated the transmit scheduler code to handle changes to the spec, specifically the firmware expects a 4KB buffer at all times so fix the default scheduler topology buffer size. Also the maximum children per node per layer is replaced by maximum sibling group size. Adds a check to ensure a reset is not in progress before exercising a control queue operation. Refactored the switch rule management functions and structures to simply the logic and to add a common function to search for a rule entry and add a new rule entry. Refactored the VSI allocation, deletion and rebuild flow so that on reset we can restore all the filters that were previously added. Did some spring cleaning of define names and macros. Dan updates the admin queue command for requesting resource ownership to the latest specification by adding new enum's and change the locks. Zhenning optimizes the driver by using the existing buffer in a structure directly versus a local array. Chinh implements handlers for ethtool for get and set link settings. Sudheer implements transmit hang/timeout detection and malicious driver detection in the driver. Md Fahad Iqbal implements the get and set bridge mode operations. Hieu adds the ability for firmware logging during initialization. Brett updates the driver to only enable VSI transmit and receive pruning when VLAN 0 is active, and when VLAN 0 is removed/not active, pruning is disabled. Akeem adds a flag to use for stopping the service task. ==================== Signed-off-by: -
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queueDavid S. Miller authored
Jeff Kirsher says: ==================== 10GbE Intel Wired LAN Driver Updates 2018-08-28 This series contains updates to ixgbe and ixgbevf only. Sebastian adds support for firmware NVM recovery mode, which logs a message when errors are detected and un-registers the device. Also fixed RSS type recognition with VF to VF communication. Shannon Nelson implements IPsec hardware offload for VF devices in Intel's 10GbE x540 family of Ethernet devices. The IPsec HW offload feature has been in the x540/Niantic family of network devices since their release in 2009, but there was no Linux kernel support for the offload until 2017. After the XFRM code added support for the offload last year, the HW offload was added to the ixgbe PF driver. Since the related x540 VF device uses same setup as the PF for implementing the offload, adding the feature to the ixgbevf seemed like a good idea. In this case, the PF owns the device registers, so the VF simply packages up the request information into a VF<->PF message and the PF does the device configuration. ==================== Signed-off-by: -
Shannon Nelson authored
When failing the request because we can't support that offload, reporting EOPNOTSUPP makes much more sense than ENXIO. Signed-off-by:
Shannon Nelson <shannon.nelson@oracle.com> Tested-by:
Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Shannon Nelson authored
There seems to be a problem in the x540's internal switch wherein if SR-IOV mode is enabled and an offloaded IPsec packet is sent to a local VF, the packet is silently dropped. This might never be a problem as it is somewhat a corner case, but if someone happens to be using IPsec offload from the PF to a VF that just happens to get migrated to the local box, communication will mysteriously fail. Not good. A simple way to protect from this is to simply not allow any IPsec offloads for outgoing packets when num_vfs != 0. This doesn't help any offloads that were created before SR-IOV was enabled, but we'll get to that later. Signed-off-by:
-
Shannon Nelson authored
Add the IPsec initialization into the driver startup and add the Rx and Tx processing hooks. Signed-off-by:
-
Shannon Nelson authored
Add the IPsec offload support code. This is based off of the similar code in ixgbe, but instead of writing the SA registers, the VF asks the PF to setup the offload by sending the offload information to the PF via the standard mailbox. Signed-off-by:
-
Shannon Nelson authored
Fix up the register definitions for using IPsec offloads and add the new mailbox message IDs. Signed-off-by:
-
Shannon Nelson authored
Add an add and a delete message for IPsec offload requests from the VF. These call into the IPsec functions that can translate the message buffer into a useful IPsec offload. These new messages bump the mbox API version to 1.4. Signed-off-by:
-
Shannon Nelson authored
Add a private flag to expressly enable support for VF IPsec offload. The VF will have to be "trusted" in order to use the hardware offload, but because of the general concerns of managing VF access, we want to be sure the user specifically is enabling the feature. This is likely a candidate for becoming a netdev feature flag. Signed-off-by:
-
Shannon Nelson authored
Add functions to translate VF IPsec offload add and delete requests into something the existing code can work with. Signed-off-by:
-
Shannon Nelson authored
Pull out a couple of values from a function so they can be used later elsewhere. Signed-off-by:
-
Shannon Nelson authored
Restore the IPsec hardware IP table after reloading the SA tables. This doesn't make much difference now, but will matter when we add support for VF IPsec offloads. Signed-off-by:
-
Shannon Nelson authored
The software SA record counters should not be cleared when clearing the hardware tables. This causes the counters to be out of sync after a driver reset. Fixes: 63a67fe2 ("ixgbe: add ipsec offload add and remove SA") Signed-off-by:
-
Sebastian Basierski authored
While VF2VF with RSS communication, RSS Type were wrongly recognized and RSS hash was not calculated as it should be. Packets was distributed on various queues by accident. This commit fixes that behaviour and causes proper RSS Type recognition. Signed-off-by:
Sebastian Basierski <sebastianx.basierski@intel.com> Tested-by:
-
Sebastian Basierski authored
Add check for FW NVM recovery mode during driver initialization and service task. If in recovery mode, log message and unregister device Signed-off-by:
Don Buchholz <donald.buchholz@intel.com> Signed-off-by:
-
Anirudh Venkataramanan authored
Remove the "ice" prefix for the driver version string and bump version to 0.7.1-k. Signed-off-by:
Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by:
Tony Brelinski <tonyx.brelinski@intel.com> Signed-off-by:
-
Akeem G Abodunrin authored
This patch introduces SERVICE_DIS flag to use for stopping service task. This flag will be checked before scheduling new tasks. Also add new functions ice_service_task_stop to stop service task. Signed-off-by:
Akeem G Abodunrin <akeem.g.abodunrin@intel.com> Signed-off-by:
-
Brett Creeley authored
VLAN pruning is not valid when VLAN 0 is not active. If VLAN pruning is enabled and VLAN 0 is not active (8021q driver not loaded) then normal, non-VLAN, traffic will not pass. TX/RX VLAN pruning is enabled when the VLAN 0 is added to the active_vlan bitmap and it is disabled when VLAN 0 is removed from the active_vlan bitmap. So, only enable VLAN pruning when VLAN 0 is active. Setting RX VLAN pruning causes the switch to drop received VLAN packets when there are no matching VLAN ids in the associated VSI's switch filters. Setting TX pruning makes it so the switch will not send out any packets with VLAN tags that don't match the associated VSI's switch filters. With this patch, if the VF or PF tries to send a VLAN tagged packet with a VLAN tag that it does not have a pruning rule for it will trigger an MDD event. For example, if PF0 has VLAN10 and VLAN11 interfaces and scapy is used to send a packet with VLAN8 then the MDD is triggered. Also make ice_vsi_kill_vlan return a value which the caller can check before updating VLAN related data structures (counts, pruning bits, etc.). Signed-off-by:
Brett Creeley <brett.creeley@intel.com> Signed-off-by:
-
Hieu Tran authored
To enable FW logging, the "cq_en" and "uart_en" enable bits of the "fw_log" element in struct ice_hw need to set accordingly based on some user-provided parameters during driver loading. To select which FW log events to be emitted, the "cfg" elements of corresponding FW modules in the "evnts" array member of "fw_log" need to be configured. Signed-off-by:
Hieu Tran <hieu.t.tran@intel.com> Signed-off-by:
-
Md Fahad Iqbal Polash authored
ice_bridge_getlink returns the current bridge mode using ndo_dflt_bridge_getlink and the mode parameter available in first_switch->bridge_mode. ice_bridge_setlink is invoked when the bridge mode needs to changed. The value to be changed to is available as a netlink message which is parsed in this function. If the mode has to be changed, switch_flags is set appropriately (set ALLOW_LB for VEB mode and clear it for VEPA mode) and ice_aq_update_vsi is called. Also change the unicast switch filter rules. Signed-off-by:
Md Fahad Iqbal Polash <md.fahad.iqbal.polash@intel.com> Signed-off-by:
-
Sudheer Mogilappagari authored
When a malicious operation is detected, the firmware triggers an interrupt, which is then picked up by the service task (specifically by ice_handle_mdd_event). A reset is scheduled if required. Tx hang detection works in a similar way, except the logic here monitors the VSI's Tx queues and tries to revive them if stalled. If the hang is not resolved, the kernel eventually calls ndo_tx_timeout, which is handled by ice_tx_timeout. Signed-off-by:
Sudheer Mogilappagari <sudheer.mogilappagari@intel.com> Signed-off-by:
-
Anirudh Venkataramanan authored
This patch cleans up the existing register definitions. 1) Several instances of long defines names used in the BIT() macro were replaced to use the actual values they represent. As a result some defines for shifts (ending with _S) that were used only to create bitmasks were removed completely. 2) Apply more consistent tab spacing. Signed-off-by:
-
Chinh Cao authored
This patch implements handlers for ethtool get_link_ksettings and set_link_ksettings. Helper functions use by these handlers are also introduced in this patch. Signed-off-by:
Chinh Cao <chinh.t.cao@intel.com> Signed-off-by:
-
Anirudh Venkataramanan authored
This patch refactors aspects of the VSI allocation, deletion and rebuild flow. Some of the more noteworthy changes are described below. 1) On reset, all switch filters applied in the hardware are lost. In the rebuild flow, only MAC and broadcast filters are being restored. Instead, use a new function ice_replay_all_fltr to restore all the filters that were previously added. To do this, remove calls to ice_remove_vsi_fltr to prevent cleaning out the internal bookkeeping structures that ice_replay_all_fltr uses to replay filters. 2) Introduce a new state bit __ICE_PREPARED_FOR_RESET to distinguish the PF that requested the reset (and consequently prepared for it) from the rest of the PFs. These other PFs will prepare for reset only when they receive an interrupt from the firmware. 3) Use new functions ice_add_vsi and ice_free_vsi to create and destroy VSIs respectively. These functions accept a handle to uniquely identify a VSI. This same handle is required to rebuild the VSI post reset. To prevent confusion, the existing ice_vsi_add was renamed to ice_vsi_init. 4) Enhance ice_vsi_setup for the upcoming SR-IOV changes and expose a new wrapper function ice_pf_vsi_setup to create PF VSIs. Rework the error handling path in ice_setup_pf_sw. 5) Introduce a new function ice_vsi_release_all to release all PF VSIs. Signed-off-by:
-
Anirudh Venkataramanan authored
This patch is an adaptation of the work originally done by Grishma Kotecha <grishma.kotecha@intel.com> that in summary refactors the switch filtering logic in the driver. More specifically, - Update the recipe structure to also store list of rules - Update the existing code for recipes like MAC, VLAN, ethtype etc to use list head that is attached to switch recipe structure - Add a common function to search for a rule entry and add a new rule entry. Update the code to use this new function. - Refactor the rem_handle_vsi_list function to simplify the logic CC: Shannon Nelson <shannon.nelson@oracle.com> Signed-off-by:
-
Zhenning Xiao authored
Use the buffer in the s_rule structure directly instead of using a local array eth_hdr[DUMMY_ETH_HDR_LEN] Signed-off-by:
Zhenning Xiao <zhenning.xiao@intel.com> Signed-off-by:
-
Anirudh Venkataramanan authored
Once reset is issued, the driver loses all control queue interfaces. Exercising control queue operations during reset is incorrect and may result in long timeouts. This patch introduces a new field 'reset_ongoing' in the hw structure. This is set to 1 by the core driver when it receives a reset interrupt. ice_sq_send_cmd checks reset_ongoing before actually issuing the control queue operation. If a reset is in progress, it returns a soft error code (ICE_ERR_RESET_PENDING) to the caller. The caller may or may not have to take any action based on this return. Once the driver knows that the reset is done, it has to set reset_ongoing back to 0. This will allow control queue operations to be posted to the hardware again. This "bail out" logic was specifically added to ice_sq_send_cmd (which is pretty low level function) so that we have one solution in one place that applies to all types of control queues. Signed-off-by:
-
Dan Nowlin authored
Align Request Resource Ownership AQ command (0x0008) to the latest specification. This includes: - Correcting the resource IDs for the Global Cfg and Change locks. - new enum ICE_CHANGE_LOCK_RES_ID - new enum ICE_GLOBAL_CFG_LOCK_RES_ID - Altering the flow for Global Config Lock to allow only the first PF to download the package. Signed-off-by:
Dan Nowlin <dan.nowlin@intel.com> Signed-off-by:
-
Anirudh Venkataramanan authored
1) The maximum device nodes is a global value and shared by the whole device. Add element AQ command would fail if there is no space to add new nodes so the check for max nodes isn't required. So remove ice_sched_get_num_nodes_per_layer and ice_sched_val_max_nodes. 2) In ice_sched_add_elems, set default node's CIR/EIR bandwidth weight. 3) Fix default scheduler topology buffer size as the firmware expects a 4KB buffer at all times, and will error out if one of any other size is provided. 4) In the latest spec, max children per node per layer is replaced by max sibling group size. Now it provides the max children of the below layer node, not the current layer node. 5) Fix some newline/whitespace issues for consistency. Signed-off-by:
-
Anirudh Venkataramanan authored
The driver can support two flex descriptor profiles, ICE_RXDID_FLEX_NIC and ICE_RXDID_FLEX_NIC_2. This patch reworks the current flex programming logic to add support for the latter profile. Signed-off-by:
-
- 27 Aug, 2018 1 commit
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds authored
Pull networking fixes from David Miller: 1) ICE, E1000, IGB, IXGBE, and I40E bug fixes from the Intel folks. 2) Better fix for AB-BA deadlock in packet scheduler code, from Cong Wang. 3) bpf sockmap fixes (zero sized key handling, etc.) from Daniel Borkmann. 4) Send zero IPID in TCP resets and SYN-RECV state ACKs, to prevent attackers using it as a side-channel. From Eric Dumazet. 5) Memory leak in mediatek bluetooth driver, from Gustavo A. R. Silva. 6) Hook up rt->dst.input of ipv6 anycast routes properly, from Hangbin Liu. 7) hns and hns3 bug fixes from Huazhong Tan. 8) Fix RIF leak in mlxsw driver, from Ido Schimmel. 9) iova range check fix in vhost, from Jason Wang. 10) Fix hang in do_tcp_sendpages() with tls, from John Fastabend. 11) More r8152 chips need to disable RX aggregation, from Kai-Heng Feng. 12) Memory exposure in TCA_U32_SEL handling, from Kees Cook. 13) TCP BBR congestion control fixes from Kevin Yang. 14) hv_netvsc, ignore non-PCI devices, from Stephen Hemminger. 15) qed driver fixes from Tomer Tayar. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (77 commits) net: sched: Fix memory exposure from short TCA_U32_SEL qed: fix spelling mistake "comparsion" -> "comparison" vhost: correctly check the iova range when waking virtqueue qlge: Fix netdev features configuration. net: macb: do not disable MDIO bus at open/close time Revert "net: stmmac: fix build failure due to missing COMMON_CLK dependency" net: macb: Fix regression breaking non-MDIO fixed-link PHYs mlxsw: spectrum_switchdev: Do not leak RIFs when removing bridge i40e: fix condition of WARN_ONCE for stat strings i40e: Fix for Tx timeouts when interface is brought up if DCB is enabled ixgbe: fix driver behaviour after issuing VFLR ixgbe: Prevent unsupported configurations with XDP ixgbe: Replace GFP_ATOMIC with GFP_KERNEL igb: Replace mdelay() with msleep() in igb_integrated_phy_loopback() igb: Replace GFP_ATOMIC with GFP_KERNEL in igb_sw_init() igb: Use an advanced ctx descriptor for launchtime e1000: ensure to free old tx/rx rings in set_ringparam() e1000: check on netif_running() before calling e1000_up() ixgb: use dma_zalloc_coherent instead of allocator/memset ice: Trivial formatting fixes ...
-
