This patch adds support for the Ka-Ro electronics GmbH TX6 modules.
There are five distinct module types with either i.MX6Q or i.MX6DL and
LVDS or LCD display interface and one DTS file for a complete system
with an i.MX6DL based TX6 module and a baseboard mounted on the back
of a display (imx6dl-tx6dl-comtft.dts).
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

This patch adds the missing (General Purpose Timer) GPT devicetree node
for i.MX35 CPUs.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

The CMO-QVGA, DVI-VGA and DVI-SVGA displays were added.
Signed-off-by: Denis Carikli <denis@eukrea.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

This patch adds CSI subnodes for IPU1 and IPU2 that will contain
ports and endpoints connecting to external elements in the video
pipeline.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

The 2.5V VDD_ETH_IO voltage supplied by the DA9063 LDO4 is used
to power the KSZ9031 PHY DVDDH input and to pull the necessary
pins (including bootstrap pins) high.
It also powers the i.MX6 NVCC_RGMII and NVCC_ENET inputs.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

The imx6dl dts supports both DualLite and Solo CPU variants
The imx6q dts supports both Dual and Quad CPU variants
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

The 'model' property in the imx-audio-sgtl5000 binding specifies the
user-visible name of the audio device. This should be something common and
not baseboard specific.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

The PWM3 pinmux configuration conflicts with gpio 3.28. Introduce a regulator
for mmc0 so that it conflicts with the pwm driver and fails gracefully. The
kernel will then able to access mmc0 normally.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

when system suspend, need to set pins to low power state to
save IO power consumption, there are three states of pinctrl:
"default", "idle" and "sleep". Currently enet supports default
and sleep state.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

GPIO4_9 is used as ECSPI1 chip select and it needs to be configured as GPIO.

Configure the pin functionality explicitly in the dts file instead of relying
on the fact that it comes configured as GPIO from POR or from the bootloader.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

This patch adds support for the cpuimx27 board from Eukrea and its
baseboard. This change is intended to further remove non-DT support
for this board.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

Add initial imx6sx-sdb board support with limited devices enabled.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

Add initial device tree source for i.MX6 SoloX SoC.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

Add pin function header for i.MX6 SoloX SoC.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

The i.MX SoC changes for 3.17:
 - Add devicetree support for i.MX1 and i.MX21 clock driver
 - Use CLOCKSOURCE_OF_DECLARE() to initialize timer for DT targets
 - Use of_clk_init() to initialize i.MX25 and i.MX27 clock driver in
   device tree boot
 - Remove i.MX1 camera support
 - Remove i.MX27 IP Camera and Lite-Kit board support
 - Add suspend and cpuidle support for i.mx6sx
 - Clean up unused clk_register_clkdev() lookups
 - Update imx-weim bus driver to support populating devices on a simple
   bus
 - Switch i.MX27 and i.MX6QDL clock driver to use macro for clock IDs
 - Make i.MX51 a DT only platform and clean up the non-DT support code
 - Support disabling supervisor protect via DT
 - Random defconfig updates

Extend the clock control for FlexCAN with the second gate which
enable the clocks in the Clock Divider (CCM_CSCDR2) register too.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

This patch uses clocksource_of_init() call for DT targets.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

Most peripherals on the i.MX53 have an
  Off-Platform Peripheral Access Control Register (OPACR)
in which the access rights (together with the MPROT registers) can be declared.
However, this does not seem to work for example for SSI1+SDMA, because the
supervisor bit is not set for the SDMA unit.
It does work for SSI2, the QSB for example uses SSI2 for its audio. But SSI2 only
works because it does NOT have an OPACR.

The right solution would be to fix the access rights for the SDMA, but the unit
responsible for this is the Central Security Unit (CSU), which of course is NOT
documented. So, until documentation for this is openly available, turn off the
supervisor protection because it cripples the hardware.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

The i.MX SoCs allow to setup fine grained access rights to peripherals on the
AIPS bus.
This is done via the Peripheral Access Register (PAR) in e.g. the i.MX21
or in later SoC versions the Off-Platform Peripheral Access Control Register
(OPACR), e.g. i.MX53.
Under certain circumstances this leads to problems in which bus masters are
not granted their access rights to peripherals.
To be able to disable these restrictions on DT platforms, add a helper function
that looks for AIPS nodes in the DT and disables them for every compatible node
it finds.
The compatible has to be declared in the mach-specific entry file, where this
helper function should then be called.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

This patch adds missing 26 MHz oscillator circuit clock gate support.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

This patch removes definitions which not used anywhere in the driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

Use clock defines in order to make devicetrees more human readable.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

The board has no insufficient support to be fully functional and seems
has no users. This patch removes support for this board.
However, the support may be added in the future by using the devicetree.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

This patch removes excess symbols ARCH_MX1, ARCH_MX25 and MACH_MX27.
Instead we use SOC_IMX*.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

i.MX1 camera driver has been removed by the commit 90b05589.
This patch removes remaining support files for this camera.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

replace IS_ERR/PTR_ERR

Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

There could be some memory map devices located in
a certain chip select region of the i.MX WEIM.
The devices could be attached to a simple bus(for
example, a AXI bus) whose root node is one child
device tree node of the i.MX WEIM device tree node.
There should be a bridge(very likely, software
transparent) bewteen the i.MX WEIM and the simple bus.
This patch makes the i.MX WEIM driver possible to
populate devices on a simple bus.  In this way, people
may try various IPs(in a FPGA, maybe) outside of i.MX
chips with the i.MX WEIM embedded.
Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

imx6q_pm_enter calls imx6sl_set_wait_clk when run on an imx6sl
based machine. However if support for imx6sl is not enabled
at compile time, this prevents us from building the kernel and
we get this link error instead:

arch/arm/mach-imx/built-in.o: In function `imx6q_pm_enter':
:(.text+0x4b84): undefined reference to `imx6sl_set_wait_clk'

This makes the cpu_is_imx6sl function conditionally return false
if imx6sl is disabled at compile-time, which matches what the
older cpu_is_mx* macros did. We have similar inline functions for
the other imx6 variants, but so far I have not run into a case
where the extra #ifdef is necessary.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

Building a kernel for imx6sx but without imx6q support results in
this link error because of the missing cpuidle driver:

arch/arm/mach-imx/built-in.o: In function `imx6sx_init_late'::(.init.text+0xc228):
 undefined reference to `imx6q_cpuidle_init'

This patch adds a Makefile entry so we always build support for
the imx6q_cpuidle code when at least one of the 6sx or 6q variants
are enabled.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

The PL310 integrated on i.MX6 series and VF610 are revision r3p1 and
later.  Per ARM PL310 errata document, 588369 is fixed in r2p0 and
727915 is fixed in r3p1.  Neither is needed for i.MX6 or VF610.  So
let's drop them.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

Add EDMA for DMA support for Vybrid SoCs. Also add printk time.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

SSI and SSI_IPG are clocks controlled by the same clock gating field, so
register them with imx_clk_gate2_shared.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

Signed-off-by: Silvio Fricke <silvio.fricke@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

Enable STMPE gpio support as this is used on MX6 Data Modul edm-qmx6
board.
Signed-off-by: Silvio Fricke <silvio.fricke@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

Otherwise GCC will mark the .init.rodata section R/W, which causes
a compile error once we add other real R/O data.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

It is only the mx6quad variant that can run up to 1.2GHz, so add the check
accordingly.

This avoids getting the following warning on a mx6solo:

failed to disable 1.2 GHz OPP
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

Allow USB device to work by default.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>