- 14 Jan, 2011 40 commits
-
-
Andres Salomon authored
This adds MODULE_ALIAS entries to the various cs5535 subdevice modules; this allows the modules to automatically be loaded when cs5535-mfd loads. Signed-off-by:
Andres Salomon <dilinger@queued.net> Signed-off-by:
Samuel Ortiz <sameo@linux.intel.com>
-
Andres Salomon authored
The cs5535-mfd driver now takes care of the PCI BAR handling; this simplifies the mfgpt driver a bunch. Signed-off-by:
-
Andres Salomon authored
The cs5535-mfd driver now takes care of the PCI BAR handling; this simplifies the gpio driver a lot. Signed-off-by:
-
Andres Salomon authored
ARRAY_SIZE() returns size_t; use %zu instead of %d so that we don't get warnings on x86-64. Signed-off-by:
Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by:
-
Mark Brown authored
Allow the WM8994 to completely power off, including disabling the LDOs if they are software controlled, when it goes idle. The CODEC subdevice controls activity for the MFD as a whole. If the GPIOs need to be used while the device is active runtime PM should be disabled for the device by machine specific code. Signed-off-by:
Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by:
-
Mark Brown authored
Allow MFD cells to have pm_runtime_no_callbacks() called on them during registration. This causes the runtime PM framework to ignore them, allowing use of runtime PM to suspend the device as a whole even if not all drivers for the MFD can usefully implement runtime PM. For example, RTCs are likely to run continuously regardless of the power state of the system. Signed-off-by:
-
Mattias Wallin authored
Replace spaces with proper tabs. Signed-off-by:
Mattias Wallin <mattias.wallin@stericsson.com> Signed-off-by:
-
Mark Brown authored
Kernel 2.6.37 adds new interrupt methods which take a struct irq_data rather than an irq number. Convert over to these as they will become mandatory in future. Signed-off-by:
-
Mark Brown authored
Kernel 2.6.37 adds new interrupt methods which take a struct irq_data rather than an irq number. Convert over to these as they will become mandatory in future. Signed-off-by:
-
Mark Brown authored
Kernel 2.6.37 adds new interrupt methods which take a struct irq_data rather than an irq number. Convert over to these as they will become mandatory in future. Signed-off-by:
-
Mark Brown authored
The WM8326 is a high performance variant of the WM832x series with no software visible differences. Signed-off-by:
-
Mark Brown authored
All the current WM832x devices have the same set of subdevices so can just use multiple case statements with a single body. Signed-off-by:
-
Joe Perches authored
Using %pR standardizes the struct resource output. Signed-off-by:
Joe Perches <joe@perches.com> Signed-off-by:
-
Andres Salomon authored
Add an MFD driver to handle the ISA device on CS5535 and CS5536 southbridges. This ISA bridge is actually multiple devices: GPIOs, MFGPTs, etc. Signed-off-by:
-
Uwe Kleine-König authored
Signed-off-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by:
-
Axel Lin authored
As warned by checkpatch.pl, use #include <linux/gpio.h> instead of <asm/gpio.h>. Signed-off-by:
Axel Lin <axel.lin@gmail.com> Signed-off-by:
-
Axel Lin authored
As warned by checkpatch.pl, use #include <linux/io.h> instead of <asm/io.h> Signed-off-by:
Ben Dooks <ben@simtec.co.uk> Signed-off-by:
-
Joe Perches authored
Remove KERN_<level>. Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6Linus Torvalds authored
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (59 commits) ACPI / PM: Fix build problems for !CONFIG_ACPI related to NVS rework ACPI: fix resource check message ACPI / Battery: Update information on info notification and resume ACPI: Drop device flag wake_capable ACPI: Always check if _PRW is present before trying to evaluate it ACPI / PM: Check status of power resources under mutexes ACPI / PM: Rename acpi_power_off_device() ACPI / PM: Drop acpi_power_nocheck ACPI / PM: Drop acpi_bus_get_power() Platform / x86: Make fujitsu_laptop use acpi_bus_update_power() ACPI / Fan: Rework the handling of power resources ACPI / PM: Register power resource devices as soon as they are needed ACPI / PM: Register acpi_power_driver early ACPI / PM: Add function for updating device power state consistently ACPI / PM: Add function for device power state initialization ACPI / PM: Introduce __acpi_bus_get_power() ACPI / PM: Introduce function for refcounting device power resources ACPI / PM: Add functions for manipulating lists of power resources ACPI / PM: Prevent acpi_power_get_inferred_state() from making changes ACPICA: Update version to 20101209 ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-idle-2.6Linus Torvalds authored
* 'idle-release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-idle-2.6: cpuidle/x86/perf: fix power:cpu_idle double end events and throw cpu_idle events from the cpuidle layer intel_idle: open broadcast clock event cpuidle: CPUIDLE_FLAG_CHECK_BM is omap3_idle specific cpuidle: CPUIDLE_FLAG_TLB_FLUSHED is specific to intel_idle cpuidle: delete unused CPUIDLE_FLAG_SHALLOW, BALANCED, DEEP definitions SH, cpuidle: delete use of NOP CPUIDLE_FLAGS_SHALLOW cpuidle: delete NOP CPUIDLE_FLAG_POLL ACPI: processor_idle: delete use of NOP CPUIDLE_FLAGs cpuidle: Rename X86 specific idle poll state[0] from C0 to POLL ACPI, intel_idle: Cleanup idle= internal variables cpuidle: Make cpuidle_enable_device() call poll_idle_init() intel_idle: update Sandy Bridge core C-state residency targets
-
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-sfi-2.6Linus Torvalds authored
* 'sfi-release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-sfi-2.6: SFI: use ioremap_cache() instead of ioremap()
-
Linus Torvalds authored
Merge branch 'vfs-scale-working' of git://git.kernel.org/pub/scm/linux/kernel/git/npiggin/linux-npiggin * 'vfs-scale-working' of git://git.kernel.org/pub/scm/linux/kernel/git/npiggin/linux-npiggin: fs: fix do_last error case when need_reval_dot nfs: add missing rcu-walk check fs: hlist UP debug fixup fs: fix dropping of rcu-walk from force_reval_path fs: force_reval_path drop rcu-walk before d_invalidate fs: small rcu-walk documentation fixes Fixed up trivial conflicts in Documentation/filesystems/porting
-
J. R. Okajima authored
When open(2) without O_DIRECTORY opens an existing dir, it should return EISDIR. In do_last(), the variable 'error' is initialized EISDIR, but it is changed by d_revalidate() which returns any positive to represent 'the target dir is valid.' Should we keep and return the initialized 'error' in this case. Signed-off-by:Nick Piggin <npiggin@kernel.dk>
-
Nick Piggin authored
Signed-off-by: -
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xenLinus Torvalds authored
* 'stable/gntdev' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen: xen/p2m: Fix module linking error. xen p2m: clear the old pte when adding a page to m2p_override xen gntdev: use gnttab_map_refs and gnttab_unmap_refs xen: introduce gnttab_map_refs and gnttab_unmap_refs xen p2m: transparently change the p2m mappings in the m2p override xen/gntdev: Fix circular locking dependency xen/gntdev: stop using "token" argument xen: gntdev: move use of GNTMAP_contains_pte next to the map_op xen: add m2p override mechanism xen: move p2m handling to separate file xen/gntdev: add VM_PFNMAP to vma xen/gntdev: allow usermode to map granted pages xen: define gnttab_set_map_op/unmap_op Fix up trivial conflict in drivers/xen/Kconfig
-
Linus Torvalds authored
Merge branch 'stable/platform-pci-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen * 'stable/platform-pci-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen: xen-platform: Fix compile errors if CONFIG_PCI is not enabled. xen: rename platform-pci module to xen-platform-pci. xen-platform: use PCI interfaces to request IO and MEM resources.
-
Nick Piggin authored
Po-Yu Chuang <ratbert.chuang@gmail.com> noticed that hlist_bl_set_first could crash on a UP system when LIST_BL_LOCKMASK is 0, because LIST_BL_BUG_ON(!((unsigned long)h->first & LIST_BL_LOCKMASK)); always evaulates to true. Fix the expression, and also avoid a dependency between bit spinlock implementation and list bl code (list code shouldn't know anything except that bit 0 is set when adding and removing elements). Eventually if a good use case comes up, we might use this list to store 1 or more arbitrary bits of data, so it really shouldn't be tied to locking either, but for now they are helpful for debugging. Signed-off-by: -
Nick Piggin authored
As J. R. Okajima noted, force_reval_path passes in the same dentry to d_revalidate as the one in the nameidata structure (other callers pass in a child), so the locking breaks. This can oops with a chrooted nfs mount, for example. Similarly there can be other problems with revalidating a dentry which is already in nameidata of the path walk. Signed-off-by: -
Nick Piggin authored
d_revalidate can return in rcu-walk mode even when it returns 0. We can't just call any old dcache function on rcu-walk dentry (the dentry is unstable, so even through d_lock can safely be taken, the result may no longer be what we expect -- careful re-checks would be required). So just drop rcu in this case. (I missed this conversion when switching to the rcu-walk convention that Linus suggested) Signed-off-by: -
Nick Piggin authored
Signed-off-by: -
Daisuke Nishimura authored
In the current implementation mem_cgroup_end_migration() decides whether the page migration has succeeded or not by checking "oldpage->mapping". But if we are tring to migrate a shmem swapcache, the page->mapping of it is NULL from the begining, so the check would be invalid. As a result, mem_cgroup_end_migration() assumes the migration has succeeded even if it's not, so "newpage" would be freed while it's not uncharged. This patch fixes it by passing mem_cgroup_end_migration() the result of the page migration. Signed-off-by:
Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp> Reviewed-by:
Minchan Kim <minchan.kim@gmail.com> Acked-by:
KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Acked-by:
Balbir Singh <balbir@linux.vnet.ibm.com> Cc: Minchan Kim <minchan.kim@gmail.com> Reviewed-by:
Johannes Weiner <hannes@cmpxchg.org> Cc: Hugh Dickins <hughd@google.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
Jesper Juhl authored
In mem_cgroup_alloc() we currently do either kmalloc() or vmalloc() then followed by memset() to zero the memory. This can be more efficiently achieved by using kzalloc() and vzalloc(). There's also one situation where we can use kzalloc_node() - this is what's new in this version of the patch. Signed-off-by:
Jesper Juhl <jj@chaosbits.net> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Minchan Kim <minchan.kim@gmail.com> Cc: Wu Fengguang <fengguang.wu@intel.com> Cc: Balbir Singh <balbir@linux.vnet.ibm.com> Cc: Li Zefan <lizf@cn.fujitsu.com> Signed-off-by:
-
Daisuke Nishimura authored
Commit b1dd693e ("memcg: avoid deadlock between move charge and try_charge()") can cause another deadlock about mmap_sem on task migration if cpuset and memcg are mounted onto the same mount point. After the commit, cgroup_attach_task() has sequence like: cgroup_attach_task() ss->can_attach() cpuset_can_attach() mem_cgroup_can_attach() down_read(&mmap_sem) (1) ss->attach() cpuset_attach() mpol_rebind_mm() down_write(&mmap_sem) (2) up_write(&mmap_sem) cpuset_migrate_mm() do_migrate_pages() down_read(&mmap_sem) up_read(&mmap_sem) mem_cgroup_move_task() mem_cgroup_clear_mc() up_read(&mmap_sem) We can cause deadlock at (2) because we've already aquire the mmap_sem at (1). But the commit itself is necessary to fix deadlocks which have existed before the commit like: Ex.1) move charge | try charge --------------------------------------+------------------------------ mem_cgroup_can_attach() | down_write(&mmap_sem) mc.moving_task = current | .. mem_cgroup_precharge_mc() | __mem_cgroup_try_charge() mem_cgroup_count_precharge() | prepare_to_wait() down_read(&mmap_sem) | if (mc.moving_task) -> cannot aquire the lock | -> true | schedule() | -> move charge should wake it up Ex.2) move charge | try charge --------------------------------------+------------------------------ mem_cgroup_can_attach() | mc.moving_task = current | mem_cgroup_precharge_mc() | mem_cgroup_count_precharge() | down_read(&mmap_sem) | .. | up_read(&mmap_sem) | | down_write(&mmap_sem) mem_cgroup_move_task() | .. mem_cgroup_move_charge() | __mem_cgroup_try_charge() down_read(&mmap_sem) | prepare_to_wait() -> cannot aquire the lock | if (mc.moving_task) | -> true | schedule() | -> move charge should wake it up This patch fixes all of these problems by: 1. revert the commit. 2. To fix the Ex.1, we set mc.moving_task after mem_cgroup_count_precharge() has released the mmap_sem. 3. To fix the Ex.2, we use down_read_trylock() instead of down_read() in mem_cgroup_move_charge() and, if it has failed to aquire the lock, cancel all extra charges, wake up all waiters, and retry trylock. Signed-off-by:
Ben Blum <bblum@andrew.cmu.edu> Cc: Miao Xie <miaox@cn.fujitsu.com> Cc: David Rientjes <rientjes@google.com> Cc: Paul Menage <menage@google.com> Cc: Hiroyuki Kamezawa <kamezawa.hiroyuki@gmail.com> Cc: Balbir Singh <balbir@in.ibm.com> Signed-off-by:
-
Minchan Kim authored
Signed-off-by:
-
Johannes Weiner authored
Adding the number of swap pages to the byte limit of a memory control group makes no sense. Convert the pages to bytes before adding them. The only user of this code is the OOM killer, and the way it is used means that the error results in a higher OOM badness value. Since the cgroup limit is the same for all tasks in the cgroup, the error should have no practical impact at the moment. But let's not wait for future or changing users to trip over it. Signed-off-by:
-
KAMEZAWA Hiroyuki authored
Introduce a new bit spin lock, PCG_MOVE_LOCK, to synchronize the page accounting and migration code. This reworks the locking scheme of _update_stat() and _move_account() by adding new lock bit PCG_MOVE_LOCK, which is always taken under IRQ disable. 1. If pages are being migrated from a memcg, then updates to that memcg page statistics are protected by grabbing PCG_MOVE_LOCK using move_lock_page_cgroup(). In an upcoming commit, memcg dirty page accounting will be updating memcg page accounting (specifically: num writeback pages) from IRQ context (softirq). Avoid a deadlocking nested spin lock attempt by disabling irq on the local processor when grabbing the PCG_MOVE_LOCK. 2. lock for update_page_stat is used only for avoiding race with move_account(). So, IRQ awareness of lock_page_cgroup() itself is not a problem. The problem is between mem_cgroup_update_page_stat() and mem_cgroup_move_account_page(). Trade-off: * Changing lock_page_cgroup() to always disable IRQ (or local_bh) has some impacts on performance and I think it's bad to disable IRQ when it's not necessary. * adding a new lock makes move_account() slower. Score is here. Performance Impact: moving a 8G anon process. Before: real 0m0.792s user 0m0.000s sys 0m0.780s After: real 0m0.854s user 0m0.000s sys 0m0.842s This score is bad but planned patches for optimization can reduce this impact. Signed-off-by:Greg Thelen <gthelen@google.com> Reviewed-by:
-
Greg Thelen authored
Replace usage of the mem_cgroup_update_file_mapped() memcg statistic update routine with two new routines: * mem_cgroup_inc_page_stat() * mem_cgroup_dec_page_stat() As before, only the file_mapped statistic is managed. However, these more general interfaces allow for new statistics to be more easily added. New statistics are added with memcg dirty page accounting. Signed-off-by:
Andrea Righi <arighi@develer.com> Acked-by:
-
Greg Thelen authored
Document cgroup dirty memory interfaces and statistics. [akpm@linux-foundation.org: fix use_hierarchy description] Signed-off-by:
-
Greg Thelen authored
This patchset provides the ability for each cgroup to have independent dirty page limits. Limiting dirty memory is like fixing the max amount of dirty (hard to reclaim) page cache used by a cgroup. So, in case of multiple cgroup writers, they will not be able to consume more than their designated share of dirty pages and will be forced to perform write-out if they cross that limit. The patches are based on a series proposed by Andrea Righi in Mar 2010. Overview: - Add page_cgroup flags to record when pages are dirty, in writeback, or nfs unstable. - Extend mem_cgroup to record the total number of pages in each of the interesting dirty states (dirty, writeback, unstable_nfs). - Add dirty parameters similar to the system-wide /proc/sys/vm/dirty_* limits to mem_cgroup. The mem_cgroup dirty parameters are accessible via cgroupfs control files. - Consider both system and per-memcg dirty limits in page writeback when deciding to queue background writeback or block for foreground writeback. Known shortcomings: - When a cgroup dirty limit is exceeded, then bdi writeback is employed to writeback dirty inodes. Bdi writeback considers inodes from any cgroup, not just inodes contributing dirty pages to the cgroup exceeding its limit. - When memory.use_hierarchy is set, then dirty limits are disabled. This is a implementation detail. An enhanced implementation is needed to check the chain of parents to ensure that no dirty limit is exceeded. Performance data: - A page fault microbenchmark workload was used to measure performance, which can be called in read or write mode: f = open(foo. $cpu) truncate(f, 4096) alarm(60) while (1) { p = mmap(f, 4096) if (write) *p = 1 else x = *p munmap(p) } - The workload was called for several points in the patch series in different modes: - s_read is a single threaded reader - s_write is a single threaded writer - p_read is a 16 thread reader, each operating on a different file - p_write is a 16 thread writer, each operating on a different file - Measurements were collected on a 16 core non-numa system using "perf stat --repeat 3". The -a option was used for parallel (p_*) runs. - All numbers are page fault rate (M/sec). Higher is better. - To compare the performance of a kernel without non-memcg compare the first and last rows, neither has memcg configured. The first row does not include any of these memcg patches. - To compare the performance of using memcg dirty limits, compare the baseline (2nd row titled "w/ memcg") with the the code and memcg enabled (2nd to last row titled "all patches"). root_cgroup child_cgroup s_read s_write p_read p_write s_read s_write p_read p_write mmotm w/o memcg 0.428 0.390 0.429 0.388 mmotm w/ memcg 0.411 0.378 0.391 0.362 0.412 0.377 0.385 0.363 all patches 0.384 0.360 0.370 0.348 0.381 0.363 0.368 0.347 all patches 0.431 0.402 0.427 0.395 w/o memcg This patch: Add additional flags to page_cgroup to track dirty pages within a mem_cgroup. Signed-off-by: -
Shaohua Li authored
The zone->lru_lock is heavily contented in workload where activate_page() is frequently used. We could do batch activate_page() to reduce the lock contention. The batched pages will be added into zone list when the pool is full or page reclaim is trying to drain them. For example, in a 4 socket 64 CPU system, create a sparse file and 64 processes, processes shared map to the file. Each process read access the whole file and then exit. The process exit will do unmap_vmas() and cause a lot of activate_page() call. In such workload, we saw about 58% total time reduction with below patch. Other workloads with a lot of activate_page also benefits a lot too. I tested some microbenchmarks: case-anon-cow-rand-mt 0.58% case-anon-cow-rand -3.30% case-anon-cow-seq-mt -0.51% case-anon-cow-seq -5.68% case-anon-r-rand-mt 0.23% case-anon-r-rand 0.81% case-anon-r-seq-mt -0.71% case-anon-r-seq -1.99% case-anon-rx-rand-mt 2.11% case-anon-rx-seq-mt 3.46% case-anon-w-rand-mt -0.03% case-anon-w-rand -0.50% case-anon-w-seq-mt -1.08% case-anon-w-seq -0.12% case-anon-wx-rand-mt -5.02% case-anon-wx-seq-mt -1.43% case-fork 1.65% case-fork-sleep -0.07% case-fork-withmem 1.39% case-hugetlb -0.59% case-lru-file-mmap-read-mt -0.54% case-lru-file-mmap-read 0.61% case-lru-file-mmap-read-rand -2.24% case-lru-file-readonce -0.64% case-lru-file-readtwice -11.69% case-lru-memcg -1.35% case-mmap-pread-rand-mt 1.88% case-mmap-pread-rand -15.26% case-mmap-pread-seq-mt 0.89% case-mmap-pread-seq -69.72% case-mmap-xread-rand-mt 0.71% case-mmap-xread-seq-mt 0.38% The most significent are: case-lru-file-readtwice -11.69% case-mmap-pread-rand -15.26% case-mmap-pread-seq -69.72% which use activate_page a lot. others are basically variations because each run has slightly difference. [akpm@linux-foundation.org: coding-style fixes] Signed-off-by:
Shaohua Li <shaohua.li@intel.com> Cc: Andi Kleen <andi@firstfloor.org> Cc: Minchan Kim <minchan.kim@gmail.com> Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: Rik van Riel <riel@redhat.com> Signed-off-by:
-
