Commit 01aa1a5c authored by Ladislav Michl's avatar Ladislav Michl Committed by Tony Lindgren

ARM: dts: omap3-igep: OneNAND support

Add OneNAND node for IGEP and leave it disabled by default. It is up
to bootloader to enable proper node. Timing just works, but values are
copied over from N900 as I was unable to find chip datasheet.
Signed-off-by: default avatarLadislav Michl <ladis@linux-mips.org>
Signed-off-by: default avatarTony Lindgren <tony@atomide.com>
parent a5e743c4
......@@ -37,6 +37,13 @@ vdd33: regulator-vdd33 {
};
&omap3_pmx_core {
gpmc_pins: pinmux_gpmc_pins {
pinctrl-single,pins = <
/* OneNAND seems to require PIN_INPUT on clock. */
OMAP3_CORE1_IOPAD(0x20be, PIN_INPUT | MUX_MODE0) /* gpmc_clk.gpmc_clk */
>;
};
uart1_pins: pinmux_uart1_pins {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x2182, PIN_INPUT | MUX_MODE0) /* uart1_rx.uart1_rx */
......@@ -98,6 +105,9 @@ OMAP3_CORE1_IOPAD(0x21c4, PIN_INPUT | MUX_MODE0) /* i2c3_sda.i2c3_sda */
};
&gpmc {
pinctrl-names = "default";
pinctrl-0 = <&gpmc_pins>;
nand@0,0 {
compatible = "ti,omap2-nand";
reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
......@@ -126,6 +136,48 @@ nand@0,0 {
#address-cells = <1>;
#size-cells = <1>;
status = "okay";
};
onenand@0,0 {
compatible = "ti,omap2-onenand";
reg = <0 0 0x20000>; /* CS0, offset 0, IO size 128K */
gpmc,sync-read;
gpmc,sync-write;
gpmc,burst-length = <16>;
gpmc,burst-read;
gpmc,burst-wrap;
gpmc,burst-write;
gpmc,device-width = <2>; /* GPMC_DEVWIDTH_16BIT */
gpmc,mux-add-data = <2>; /* GPMC_MUX_AD */
gpmc,cs-on-ns = <0>;
gpmc,cs-rd-off-ns = <87>;
gpmc,cs-wr-off-ns = <87>;
gpmc,adv-on-ns = <0>;
gpmc,adv-rd-off-ns = <10>;
gpmc,adv-wr-off-ns = <10>;
gpmc,oe-on-ns = <15>;
gpmc,oe-off-ns = <87>;
gpmc,we-on-ns = <0>;
gpmc,we-off-ns = <87>;
gpmc,rd-cycle-ns = <112>;
gpmc,wr-cycle-ns = <112>;
gpmc,access-ns = <81>;
gpmc,page-burst-access-ns = <15>;
gpmc,bus-turnaround-ns = <0>;
gpmc,cycle2cycle-delay-ns = <0>;
gpmc,wait-monitoring-ns = <0>;
gpmc,clk-activation-ns = <5>;
gpmc,wr-data-mux-bus-ns = <30>;
gpmc,wr-access-ns = <81>;
gpmc,sync-clk-ps = <15000>;
#address-cells = <1>;
#size-cells = <1>;
status = "disabled";
};
};
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment