Merge tag 'usb-3.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb

Pull USB fixes from Greg KH:
 "Here are some USB fixes and new device ids for 3.12-rc6

  The largest change here is a bunch of new device ids for the option
  USB serial driver for new Huawei devices.  Other than that, just some
  small bug fixes for issues that people have reported (run-time and
  build-time), nothing major"

* tag 'usb-3.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb: usb_phy_gen: refine conditional declaration of usb_nop_xceiv_register
  usb: misc: usb3503: Fix compile error due to incorrect regmap depedency
  usb/chipidea: fix oops on memory allocation failure
  usb-storage: add quirk for mandatory READ_CAPACITY_16
  usb: serial: option: blacklist Olivetti Olicard200
  USB: quirks: add touchscreen that is dazzeled by remote wakeup
  Revert "usb: musb: gadget: fix otg active status flag"
  USB: quirks.c: add one device that cannot deal with suspension
  USB: serial: option: add support for Inovia SEW858 device
  USB: serial: ti_usb_3410_5052: add Abbott strip port ID to combined table as well.
  USB: support new huawei devices in option.c
  usb: musb: start musb on the udc side, too
  xhci: Fix spurious wakeups after S5 on Haswell
  xhci: fix write to USB3_PSSEN and XUSB2PRM pci config registers
  xhci: quirk for extra long delay for S4
  xhci: Don't enable/disable RWE on bus suspend/resume.

drivers/usb/chipidea/host.c

@@ -100,8 +100,10 @@ static void host_stop(struct ci_hdrc *ci)
 {
 	struct usb_hcd *hcd = ci->hcd;
 
+	if (hcd) {
 		usb_remove_hcd(hcd);
 		usb_put_hcd(hcd);
+	}
 	if (ci->platdata->reg_vbus)
 		regulator_disable(ci->platdata->reg_vbus);
 }

drivers/usb/core/quirks.c

@@ -97,6 +97,9 @@ static const struct usb_device_id usb_quirk_list[] = {
 	/* Alcor Micro Corp. Hub */
 	{ USB_DEVICE(0x058f, 0x9254), .driver_info = USB_QUIRK_RESET_RESUME },
 
+	/* MicroTouch Systems touchscreen */
+	{ USB_DEVICE(0x0596, 0x051e), .driver_info = USB_QUIRK_RESET_RESUME },
+
 	/* appletouch */
 	{ USB_DEVICE(0x05ac, 0x021a), .driver_info = USB_QUIRK_RESET_RESUME },
 
@@ -130,6 +133,9 @@ static const struct usb_device_id usb_quirk_list[] = {
 	/* Broadcom BCM92035DGROM BT dongle */
 	{ USB_DEVICE(0x0a5c, 0x2021), .driver_info = USB_QUIRK_RESET_RESUME },
 
+	/* MAYA44USB sound device */
+	{ USB_DEVICE(0x0a92, 0x0091), .driver_info = USB_QUIRK_RESET_RESUME },
+
 	/* Action Semiconductor flash disk */
 	{ USB_DEVICE(0x10d6, 0x2200), .driver_info =
 			USB_QUIRK_STRING_FETCH_255 },

drivers/usb/host/pci-quirks.c

@@ -799,7 +799,7 @@ void usb_enable_intel_xhci_ports(struct pci_dev *xhci_pdev)
 	 * switchable ports.
 	 */
 	pci_write_config_dword(xhci_pdev, USB_INTEL_USB3_PSSEN,
-			cpu_to_le32(ports_available));
+			ports_available);
 
 	pci_read_config_dword(xhci_pdev, USB_INTEL_USB3_PSSEN,
 			&ports_available);
@@ -821,7 +821,7 @@ void usb_enable_intel_xhci_ports(struct pci_dev *xhci_pdev)
 	 * host.
 	 */
 	pci_write_config_dword(xhci_pdev, USB_INTEL_XUSB2PR,
-			cpu_to_le32(ports_available));
+			ports_available);
 
 	pci_read_config_dword(xhci_pdev, USB_INTEL_XUSB2PR,
 			&ports_available);

drivers/usb/host/xhci-hub.c

@@ -1157,18 +1157,6 @@ int xhci_bus_suspend(struct usb_hcd *hcd)
 		t1 = xhci_port_state_to_neutral(t1);
 		if (t1 != t2)
 			xhci_writel(xhci, t2, port_array[port_index]);
-
-		if (hcd->speed != HCD_USB3) {
-			/* enable remote wake up for USB 2.0 */
-			__le32 __iomem *addr;
-			u32 tmp;
-
-			/* Get the port power control register address. */
-			addr = port_array[port_index] + PORTPMSC;
-			tmp = xhci_readl(xhci, addr);
-			tmp |= PORT_RWE;
-			xhci_writel(xhci, tmp, addr);
-		}
 	}
 	hcd->state = HC_STATE_SUSPENDED;
 	bus_state->next_statechange = jiffies + msecs_to_jiffies(10);
@@ -1247,20 +1235,6 @@ int xhci_bus_resume(struct usb_hcd *hcd)
 				xhci_ring_device(xhci, slot_id);
 		} else
 			xhci_writel(xhci, temp, port_array[port_index]);
-
-		if (hcd->speed != HCD_USB3) {
-			/* disable remote wake up for USB 2.0 */
-			__le32 __iomem *addr;
-			u32 tmp;
-
-			/* Add one to the port status register address to get
-			 * the port power control register address.
-			 */
-			addr = port_array[port_index] + PORTPMSC;
-			tmp = xhci_readl(xhci, addr);
-			tmp &= ~PORT_RWE;
-			xhci_writel(xhci, tmp, addr);
-		}
 	}
 
 	(void) xhci_readl(xhci, &xhci->op_regs->command);

drivers/usb/host/xhci-pci.c

@@ -35,6 +35,9 @@
 #define PCI_VENDOR_ID_ETRON		0x1b6f
 #define PCI_DEVICE_ID_ASROCK_P67	0x7023
 
+#define PCI_DEVICE_ID_INTEL_LYNXPOINT_XHCI	0x8c31
+#define PCI_DEVICE_ID_INTEL_LYNXPOINT_LP_XHCI	0x9c31
+
 static const char hcd_name[] = "xhci_hcd";
 
 /* called after powerup, by probe or system-pm "wakeup" */
@@ -69,6 +72,14 @@ static void xhci_pci_quirks(struct device *dev, struct xhci_hcd *xhci)
 				"QUIRK: Fresco Logic xHC needs configure"
 				" endpoint cmd after reset endpoint");
 		}
+		if (pdev->device == PCI_DEVICE_ID_FRESCO_LOGIC_PDK &&
+				pdev->revision == 0x4) {
+			xhci->quirks |= XHCI_SLOW_SUSPEND;
+			xhci_dbg_trace(xhci, trace_xhci_dbg_quirks,
+				"QUIRK: Fresco Logic xHC revision %u"
+				"must be suspended extra slowly",
+				pdev->revision);
+		}
 		/* Fresco Logic confirms: all revisions of this chip do not
 		 * support MSI, even though some of them claim to in their PCI
 		 * capabilities.
@@ -110,6 +121,15 @@ static void xhci_pci_quirks(struct device *dev, struct xhci_hcd *xhci)
 		xhci->quirks |= XHCI_SPURIOUS_REBOOT;
 		xhci->quirks |= XHCI_AVOID_BEI;
 	}
+	if (pdev->vendor == PCI_VENDOR_ID_INTEL &&
+	    (pdev->device == PCI_DEVICE_ID_INTEL_LYNXPOINT_XHCI ||
+	     pdev->device == PCI_DEVICE_ID_INTEL_LYNXPOINT_LP_XHCI)) {
+		/* Workaround for occasional spurious wakeups from S5 (or
+		 * any other sleep) on Haswell machines with LPT and LPT-LP
+		 * with the new Intel BIOS
+		 */
+		xhci->quirks |= XHCI_SPURIOUS_WAKEUP;
+	}
 	if (pdev->vendor == PCI_VENDOR_ID_ETRON &&
 			pdev->device == PCI_DEVICE_ID_ASROCK_P67) {
 		xhci->quirks |= XHCI_RESET_ON_RESUME;
@@ -217,6 +237,11 @@ static void xhci_pci_remove(struct pci_dev *dev)
 		usb_put_hcd(xhci->shared_hcd);
 	}
 	usb_hcd_pci_remove(dev);
+
+	/* Workaround for spurious wakeups at shutdown with HSW */
+	if (xhci->quirks & XHCI_SPURIOUS_WAKEUP)
+		pci_set_power_state(dev, PCI_D3hot);
+
 	kfree(xhci);
 }
 

drivers/usb/host/xhci.c

@@ -730,6 +730,9 @@ void xhci_shutdown(struct usb_hcd *hcd)
 
 	spin_lock_irq(&xhci->lock);
 	xhci_halt(xhci);
+	/* Workaround for spurious wakeups at shutdown with HSW */
+	if (xhci->quirks & XHCI_SPURIOUS_WAKEUP)
+		xhci_reset(xhci);
 	spin_unlock_irq(&xhci->lock);
 
 	xhci_cleanup_msix(xhci);
@@ -737,6 +740,10 @@ void xhci_shutdown(struct usb_hcd *hcd)
 	xhci_dbg_trace(xhci, trace_xhci_dbg_init,
 			"xhci_shutdown completed - status = %x",
 			xhci_readl(xhci, &xhci->op_regs->status));
+
+	/* Yet another workaround for spurious wakeups at shutdown with HSW */
+	if (xhci->quirks & XHCI_SPURIOUS_WAKEUP)
+		pci_set_power_state(to_pci_dev(hcd->self.controller), PCI_D3hot);
 }
 
 #ifdef CONFIG_PM
@@ -839,6 +846,7 @@ static void xhci_clear_command_ring(struct xhci_hcd *xhci)
 int xhci_suspend(struct xhci_hcd *xhci)
 {
 	int			rc = 0;
+	unsigned int		delay = XHCI_MAX_HALT_USEC;
 	struct usb_hcd		*hcd = xhci_to_hcd(xhci);
 	u32			command;
 
@@ -861,8 +869,12 @@ int xhci_suspend(struct xhci_hcd *xhci)
 	command = xhci_readl(xhci, &xhci->op_regs->command);
 	command &= ~CMD_RUN;
 	xhci_writel(xhci, command, &xhci->op_regs->command);
+
+	/* Some chips from Fresco Logic need an extraordinary delay */
+	delay *= (xhci->quirks & XHCI_SLOW_SUSPEND) ? 10 : 1;
+
 	if (xhci_handshake(xhci, &xhci->op_regs->status,
-		      STS_HALT, STS_HALT, XHCI_MAX_HALT_USEC)) {
+		      STS_HALT, STS_HALT, delay)) {
 		xhci_warn(xhci, "WARN: xHC CMD_RUN timeout\n");
 		spin_unlock_irq(&xhci->lock);
 		return -ETIMEDOUT;

drivers/usb/host/xhci.h

@@ -1548,6 +1548,8 @@ struct xhci_hcd {
 #define XHCI_COMP_MODE_QUIRK	(1 << 14)
 #define XHCI_AVOID_BEI		(1 << 15)
 #define XHCI_PLAT		(1 << 16)
+#define XHCI_SLOW_SUSPEND	(1 << 17)
+#define XHCI_SPURIOUS_WAKEUP	(1 << 18)
 	unsigned int		num_active_eps;
 	unsigned int		limit_active_eps;
 	/* There are two roothubs to keep track of bus suspend info for */

drivers/usb/misc/Kconfig

@@ -246,6 +246,6 @@ config USB_EZUSB_FX2
 config USB_HSIC_USB3503
        tristate "USB3503 HSIC to USB20 Driver"
        depends on I2C
-       select REGMAP
+       select REGMAP_I2C
        help
          This option enables support for SMSC USB3503 HSIC to USB 2.0 Driver.

drivers/usb/musb/musb_core.c

@@ -921,6 +921,52 @@ static void musb_generic_disable(struct musb *musb)
 
 }
 
+/*
+ * Program the HDRC to start (enable interrupts, dma, etc.).
+ */
+void musb_start(struct musb *musb)
+{
+	void __iomem    *regs = musb->mregs;
+	u8              devctl = musb_readb(regs, MUSB_DEVCTL);
+
+	dev_dbg(musb->controller, "<== devctl %02x\n", devctl);
+
+	/*  Set INT enable registers, enable interrupts */
+	musb->intrtxe = musb->epmask;
+	musb_writew(regs, MUSB_INTRTXE, musb->intrtxe);
+	musb->intrrxe = musb->epmask & 0xfffe;
+	musb_writew(regs, MUSB_INTRRXE, musb->intrrxe);
+	musb_writeb(regs, MUSB_INTRUSBE, 0xf7);
+
+	musb_writeb(regs, MUSB_TESTMODE, 0);
+
+	/* put into basic highspeed mode and start session */
+	musb_writeb(regs, MUSB_POWER, MUSB_POWER_ISOUPDATE
+			| MUSB_POWER_HSENAB
+			/* ENSUSPEND wedges tusb */
+			/* | MUSB_POWER_ENSUSPEND */
+		   );
+
+	musb->is_active = 0;
+	devctl = musb_readb(regs, MUSB_DEVCTL);
+	devctl &= ~MUSB_DEVCTL_SESSION;
+
+	/* session started after:
+	 * (a) ID-grounded irq, host mode;
+	 * (b) vbus present/connect IRQ, peripheral mode;
+	 * (c) peripheral initiates, using SRP
+	 */
+	if (musb->port_mode != MUSB_PORT_MODE_HOST &&
+			(devctl & MUSB_DEVCTL_VBUS) == MUSB_DEVCTL_VBUS) {
+		musb->is_active = 1;
+	} else {
+		devctl |= MUSB_DEVCTL_SESSION;
+	}
+
+	musb_platform_enable(musb);
+	musb_writeb(regs, MUSB_DEVCTL, devctl);
+}
+
 /*
  * Make the HDRC stop (disable interrupts, etc.);
  * reversible by musb_start

drivers/usb/musb/musb_core.h

@@ -503,6 +503,7 @@ static inline void musb_configure_ep0(struct musb *musb)
 extern const char musb_driver_name[];
 
 extern void musb_stop(struct musb *musb);
+extern void musb_start(struct musb *musb);
 
 extern void musb_write_fifo(struct musb_hw_ep *ep, u16 len, const u8 *src);
 extern void musb_read_fifo(struct musb_hw_ep *ep, u16 len, u8 *dst);

drivers/usb/musb/musb_gadget.c

@@ -1853,11 +1853,14 @@ static int musb_gadget_start(struct usb_gadget *g,
 	musb->gadget_driver = driver;
 
 	spin_lock_irqsave(&musb->lock, flags);
+	musb->is_active = 1;
 
 	otg_set_peripheral(otg, &musb->g);
 	musb->xceiv->state = OTG_STATE_B_IDLE;
 	spin_unlock_irqrestore(&musb->lock, flags);
 
+	musb_start(musb);
+
 	/* REVISIT:  funcall to other code, which also
 	 * handles power budgeting ... this way also
 	 * ensures HdrcStart is indirectly called.

drivers/usb/musb/musb_virthub.c

@@ -44,52 +44,6 @@
 
 #include "musb_core.h"
 
-/*
-* Program the HDRC to start (enable interrupts, dma, etc.).
-*/
-static void musb_start(struct musb *musb)
-{
-	void __iomem	*regs = musb->mregs;
-	u8		devctl = musb_readb(regs, MUSB_DEVCTL);
-
-	dev_dbg(musb->controller, "<== devctl %02x\n", devctl);
-
-	/*  Set INT enable registers, enable interrupts */
-	musb->intrtxe = musb->epmask;
-	musb_writew(regs, MUSB_INTRTXE, musb->intrtxe);
-	musb->intrrxe = musb->epmask & 0xfffe;
-	musb_writew(regs, MUSB_INTRRXE, musb->intrrxe);
-	musb_writeb(regs, MUSB_INTRUSBE, 0xf7);
-
-	musb_writeb(regs, MUSB_TESTMODE, 0);
-
-	/* put into basic highspeed mode and start session */
-	musb_writeb(regs, MUSB_POWER, MUSB_POWER_ISOUPDATE
-						| MUSB_POWER_HSENAB
-						/* ENSUSPEND wedges tusb */
-						/* | MUSB_POWER_ENSUSPEND */
-						);
-
-	musb->is_active = 0;
-	devctl = musb_readb(regs, MUSB_DEVCTL);
-	devctl &= ~MUSB_DEVCTL_SESSION;
-
-	/* session started after:
-	 * (a) ID-grounded irq, host mode;
-	 * (b) vbus present/connect IRQ, peripheral mode;
-	 * (c) peripheral initiates, using SRP
-	 */
-	if (musb->port_mode != MUSB_PORT_MODE_HOST &&
-	    (devctl & MUSB_DEVCTL_VBUS) == MUSB_DEVCTL_VBUS) {
-		musb->is_active = 1;
-	} else {
-		devctl |= MUSB_DEVCTL_SESSION;
-	}
-
-	musb_platform_enable(musb);
-	musb_writeb(regs, MUSB_DEVCTL, devctl);
-}
-
 static void musb_port_suspend(struct musb *musb, bool do_suspend)
 {
 	struct usb_otg	*otg = musb->xceiv->otg;

drivers/usb/serial/ti_usb_3410_5052.c

@@ -190,6 +190,7 @@ static struct usb_device_id ti_id_table_combined[] = {
 	{ USB_DEVICE(IBM_VENDOR_ID, IBM_454B_PRODUCT_ID) },
 	{ USB_DEVICE(IBM_VENDOR_ID, IBM_454C_PRODUCT_ID) },
 	{ USB_DEVICE(ABBOTT_VENDOR_ID, ABBOTT_PRODUCT_ID) },
+	{ USB_DEVICE(ABBOTT_VENDOR_ID, ABBOTT_STRIP_PORT_ID) },
 	{ USB_DEVICE(TI_VENDOR_ID, FRI2_PRODUCT_ID) },
 	{ }	/* terminator */
 };

drivers/usb/storage/scsiglue.c

@@ -211,7 +211,10 @@ static int slave_configure(struct scsi_device *sdev)
 		/*
 		 * Many devices do not respond properly to READ_CAPACITY_16.
 		 * Tell the SCSI layer to try READ_CAPACITY_10 first.
+		 * However some USB 3.0 drive enclosures return capacity
+		 * modulo 2TB. Those must use READ_CAPACITY_16
 		 */
+		if (!(us->fflags & US_FL_NEEDS_CAP16))
 			sdev->try_rc_10_first = 1;
 
 		/* assume SPC3 or latter devices support sense size > 18 */

drivers/usb/storage/unusual_devs.h

@@ -1925,6 +1925,13 @@ UNUSUAL_DEV(  0x1652, 0x6600, 0x0201, 0x0201,
 		USB_SC_DEVICE, USB_PR_DEVICE, NULL,
 		US_FL_IGNORE_RESIDUE ),
 
+/* Reported by Oliver Neukum <oneukum@suse.com> */
+UNUSUAL_DEV(  0x174c, 0x55aa, 0x0100, 0x0100,
+		"ASMedia",
+		"AS2105",
+		USB_SC_DEVICE, USB_PR_DEVICE, NULL,
+		US_FL_NEEDS_CAP16),
+
 /* Reported by Jesse Feddema <jdfeddema@gmail.com> */
 UNUSUAL_DEV(  0x177f, 0x0400, 0x0000, 0x0000,
 		"Yarvik",

include/linux/usb/usb_phy_gen_xceiv.h

@@ -12,7 +12,7 @@ struct usb_phy_gen_xceiv_platform_data {
 	unsigned int needs_reset:1;
 };
 
-#if IS_ENABLED(CONFIG_NOP_USB_XCEIV)
+#if defined(CONFIG_NOP_USB_XCEIV) || (defined(CONFIG_NOP_USB_XCEIV_MODULE) && defined(MODULE))
 /* sometimes transceivers are accessed only through e.g. ULPI */
 extern void usb_nop_xceiv_register(void);
 extern void usb_nop_xceiv_unregister(void);

include/linux/usb_usual.h

@@ -66,7 +66,9 @@
 	US_FLAG(INITIAL_READ10,	0x00100000)			\
 		/* Initial READ(10) (and others) must be retried */	\
 	US_FLAG(WRITE_CACHE,	0x00200000)			\
-		/* Write Cache status is not available */
+		/* Write Cache status is not available */	\
+	US_FLAG(NEEDS_CAP16,	0x00400000)
+		/* cannot handle READ_CAPACITY_10 */
 
 #define US_FLAG(name, value)	US_FL_##name = value ,
 enum { US_DO_ALL_FLAGS };