Commit 03be7005 authored by Dave Airlie's avatar Dave Airlie

Merge tag 'topic/drm-misc-2015-03-10' of git://anongit.freedesktop.org/drm-intel into drm-next

Another pile of misc drm patches all over, mostly polish for atomic. Last
minute rebase was to avoid the broken merge.

* tag 'topic/drm-misc-2015-03-10' of git://anongit.freedesktop.org/drm-intel:
  drm: Check in setcrtc if the primary plane supports the fb pixel format
  drm: Lighten sysfs connector 'status'
  drm/plane-helper: unexport drm_primary_helper_create_plane
  drm: Share plane pixel format check code between legacy and atomic
  drm: Fix trivial typos in comments
  drm/dp: add DPCD definitions from eDP 1.4
  drm/dp: add DPCD definitions from DP 1.1 and 1.2a
  drm: Fixup racy refcounting in plane_force_disable
  drm/i915: Rotation property is now handled in DRM core
  drm: Complete moving rotation property to core
  drm/dp: add DPCD definitions from eDP 1.2
  drm/dp: indentation and ordering cleanups
  drm/atomic-helper: Fix kerneldoc for prepare_planes
  drm: Remove redundant code in the getencoder ioctl
parents 3a656b54 7eb5f302
...@@ -450,6 +450,8 @@ drm_atomic_plane_get_property(struct drm_plane *plane, ...@@ -450,6 +450,8 @@ drm_atomic_plane_get_property(struct drm_plane *plane,
*val = state->src_w; *val = state->src_w;
} else if (property == config->prop_src_h) { } else if (property == config->prop_src_h) {
*val = state->src_h; *val = state->src_h;
} else if (property == config->rotation_property) {
*val = state->rotation;
} else if (plane->funcs->atomic_get_property) { } else if (plane->funcs->atomic_get_property) {
return plane->funcs->atomic_get_property(plane, state, property, val); return plane->funcs->atomic_get_property(plane, state, property, val);
} else { } else {
...@@ -473,7 +475,7 @@ static int drm_atomic_plane_check(struct drm_plane *plane, ...@@ -473,7 +475,7 @@ static int drm_atomic_plane_check(struct drm_plane *plane,
struct drm_plane_state *state) struct drm_plane_state *state)
{ {
unsigned int fb_width, fb_height; unsigned int fb_width, fb_height;
unsigned int i; int ret;
/* either *both* CRTC and FB must be set, or neither */ /* either *both* CRTC and FB must be set, or neither */
if (WARN_ON(state->crtc && !state->fb)) { if (WARN_ON(state->crtc && !state->fb)) {
...@@ -495,13 +497,11 @@ static int drm_atomic_plane_check(struct drm_plane *plane, ...@@ -495,13 +497,11 @@ static int drm_atomic_plane_check(struct drm_plane *plane,
} }
/* Check whether this plane supports the fb pixel format. */ /* Check whether this plane supports the fb pixel format. */
for (i = 0; i < plane->format_count; i++) ret = drm_plane_check_pixel_format(plane, state->fb->pixel_format);
if (state->fb->pixel_format == plane->format_types[i]) if (ret) {
break;
if (i == plane->format_count) {
DRM_DEBUG_ATOMIC("Invalid pixel format %s\n", DRM_DEBUG_ATOMIC("Invalid pixel format %s\n",
drm_get_format_name(state->fb->pixel_format)); drm_get_format_name(state->fb->pixel_format));
return -EINVAL; return ret;
} }
/* Give drivers some help against integer overflows */ /* Give drivers some help against integer overflows */
......
...@@ -1096,9 +1096,9 @@ EXPORT_SYMBOL(drm_atomic_helper_commit); ...@@ -1096,9 +1096,9 @@ EXPORT_SYMBOL(drm_atomic_helper_commit);
*/ */
/** /**
* drm_atomic_helper_prepare_planes - prepare plane resources after commit * drm_atomic_helper_prepare_planes - prepare plane resources before commit
* @dev: DRM device * @dev: DRM device
* @state: atomic state object with old state structures * @state: atomic state object with new state structures
* *
* This function prepares plane state, specifically framebuffers, for the new * This function prepares plane state, specifically framebuffers, for the new
* configuration. If any failure is encountered this function will call * configuration. If any failure is encountered this function will call
......
...@@ -524,17 +524,6 @@ void drm_framebuffer_reference(struct drm_framebuffer *fb) ...@@ -524,17 +524,6 @@ void drm_framebuffer_reference(struct drm_framebuffer *fb)
} }
EXPORT_SYMBOL(drm_framebuffer_reference); EXPORT_SYMBOL(drm_framebuffer_reference);
static void drm_framebuffer_free_bug(struct kref *kref)
{
BUG();
}
static void __drm_framebuffer_unreference(struct drm_framebuffer *fb)
{
DRM_DEBUG("%p: FB ID: %d (%d)\n", fb, fb->base.id, atomic_read(&fb->refcount.refcount));
kref_put(&fb->refcount, drm_framebuffer_free_bug);
}
/** /**
* drm_framebuffer_unregister_private - unregister a private fb from the lookup idr * drm_framebuffer_unregister_private - unregister a private fb from the lookup idr
* @fb: fb to unregister * @fb: fb to unregister
...@@ -1319,7 +1308,7 @@ void drm_plane_force_disable(struct drm_plane *plane) ...@@ -1319,7 +1308,7 @@ void drm_plane_force_disable(struct drm_plane *plane)
return; return;
} }
/* disconnect the plane from the fb and crtc: */ /* disconnect the plane from the fb and crtc: */
__drm_framebuffer_unreference(plane->old_fb); drm_framebuffer_unreference(plane->old_fb);
plane->old_fb = NULL; plane->old_fb = NULL;
plane->fb = NULL; plane->fb = NULL;
plane->crtc = NULL; plane->crtc = NULL;
...@@ -2285,8 +2274,6 @@ int drm_mode_getencoder(struct drm_device *dev, void *data, ...@@ -2285,8 +2274,6 @@ int drm_mode_getencoder(struct drm_device *dev, void *data,
crtc = drm_encoder_get_crtc(encoder); crtc = drm_encoder_get_crtc(encoder);
if (crtc) if (crtc)
enc_resp->crtc_id = crtc->base.id; enc_resp->crtc_id = crtc->base.id;
else if (encoder->crtc)
enc_resp->crtc_id = encoder->crtc->base.id;
else else
enc_resp->crtc_id = 0; enc_resp->crtc_id = 0;
drm_modeset_unlock(&dev->mode_config.connection_mutex); drm_modeset_unlock(&dev->mode_config.connection_mutex);
...@@ -2421,6 +2408,27 @@ int drm_mode_getplane(struct drm_device *dev, void *data, ...@@ -2421,6 +2408,27 @@ int drm_mode_getplane(struct drm_device *dev, void *data,
return 0; return 0;
} }
/**
* drm_plane_check_pixel_format - Check if the plane supports the pixel format
* @plane: plane to check for format support
* @format: the pixel format
*
* Returns:
* Zero of @plane has @format in its list of supported pixel formats, -EINVAL
* otherwise.
*/
int drm_plane_check_pixel_format(const struct drm_plane *plane, u32 format)
{
unsigned int i;
for (i = 0; i < plane->format_count; i++) {
if (format == plane->format_types[i])
return 0;
}
return -EINVAL;
}
/* /*
* setplane_internal - setplane handler for internal callers * setplane_internal - setplane handler for internal callers
* *
...@@ -2441,7 +2449,6 @@ static int __setplane_internal(struct drm_plane *plane, ...@@ -2441,7 +2449,6 @@ static int __setplane_internal(struct drm_plane *plane,
{ {
int ret = 0; int ret = 0;
unsigned int fb_width, fb_height; unsigned int fb_width, fb_height;
unsigned int i;
/* No fb means shut it down */ /* No fb means shut it down */
if (!fb) { if (!fb) {
...@@ -2464,13 +2471,10 @@ static int __setplane_internal(struct drm_plane *plane, ...@@ -2464,13 +2471,10 @@ static int __setplane_internal(struct drm_plane *plane,
} }
/* Check whether this plane supports the fb pixel format. */ /* Check whether this plane supports the fb pixel format. */
for (i = 0; i < plane->format_count; i++) ret = drm_plane_check_pixel_format(plane, fb->pixel_format);
if (fb->pixel_format == plane->format_types[i]) if (ret) {
break;
if (i == plane->format_count) {
DRM_DEBUG_KMS("Invalid pixel format %s\n", DRM_DEBUG_KMS("Invalid pixel format %s\n",
drm_get_format_name(fb->pixel_format)); drm_get_format_name(fb->pixel_format));
ret = -EINVAL;
goto out; goto out;
} }
...@@ -2794,6 +2798,23 @@ int drm_mode_setcrtc(struct drm_device *dev, void *data, ...@@ -2794,6 +2798,23 @@ int drm_mode_setcrtc(struct drm_device *dev, void *data,
drm_mode_set_crtcinfo(mode, CRTC_INTERLACE_HALVE_V); drm_mode_set_crtcinfo(mode, CRTC_INTERLACE_HALVE_V);
/*
* Check whether the primary plane supports the fb pixel format.
* Drivers not implementing the universal planes API use a
* default formats list provided by the DRM core which doesn't
* match real hardware capabilities. Skip the check in that
* case.
*/
if (!crtc->primary->format_default) {
ret = drm_plane_check_pixel_format(crtc->primary,
fb->pixel_format);
if (ret) {
DRM_DEBUG_KMS("Invalid pixel format %s\n",
drm_get_format_name(fb->pixel_format));
goto out;
}
}
ret = drm_crtc_check_viewport(crtc, crtc_req->x, crtc_req->y, ret = drm_crtc_check_viewport(crtc, crtc_req->x, crtc_req->y,
mode, fb); mode, fb);
if (ret) if (ret)
......
...@@ -278,7 +278,7 @@ struct drm_display_mode *drm_cvt_mode(struct drm_device *dev, int hdisplay, ...@@ -278,7 +278,7 @@ struct drm_display_mode *drm_cvt_mode(struct drm_device *dev, int hdisplay,
hblank = drm_mode->hdisplay * hblank_percentage / hblank = drm_mode->hdisplay * hblank_percentage /
(100 * HV_FACTOR - hblank_percentage); (100 * HV_FACTOR - hblank_percentage);
hblank -= hblank % (2 * CVT_H_GRANULARITY); hblank -= hblank % (2 * CVT_H_GRANULARITY);
/* 14. find the total pixes per line */ /* 14. find the total pixels per line */
drm_mode->htotal = drm_mode->hdisplay + hblank; drm_mode->htotal = drm_mode->hdisplay + hblank;
drm_mode->hsync_end = drm_mode->hdisplay + hblank / 2; drm_mode->hsync_end = drm_mode->hdisplay + hblank / 2;
drm_mode->hsync_start = drm_mode->hsync_end - drm_mode->hsync_start = drm_mode->hsync_end -
...@@ -1209,7 +1209,7 @@ EXPORT_SYMBOL(drm_mode_connector_list_update); ...@@ -1209,7 +1209,7 @@ EXPORT_SYMBOL(drm_mode_connector_list_update);
* <xres>x<yres>[M][R][-<bpp>][@<refresh>][i][m][eDd] * <xres>x<yres>[M][R][-<bpp>][@<refresh>][i][m][eDd]
* *
* The intermediate drm_cmdline_mode structure is required to store additional * The intermediate drm_cmdline_mode structure is required to store additional
* options from the command line modline like the force-enabel/disable flag. * options from the command line modline like the force-enable/disable flag.
* *
* Returns: * Returns:
* True if a valid modeline has been parsed, false otherwise. * True if a valid modeline has been parsed, false otherwise.
......
...@@ -344,20 +344,7 @@ const struct drm_plane_funcs drm_primary_helper_funcs = { ...@@ -344,20 +344,7 @@ const struct drm_plane_funcs drm_primary_helper_funcs = {
}; };
EXPORT_SYMBOL(drm_primary_helper_funcs); EXPORT_SYMBOL(drm_primary_helper_funcs);
/** static struct drm_plane *create_primary_plane(struct drm_device *dev)
* drm_primary_helper_create_plane() - Create a generic primary plane
* @dev: drm device
* @formats: pixel formats supported, or NULL for a default safe list
* @num_formats: size of @formats; ignored if @formats is NULL
*
* Allocates and initializes a primary plane that can be used with the primary
* plane helpers. Drivers that wish to use driver-specific plane structures or
* provide custom handler functions may perform their own allocation and
* initialization rather than calling this function.
*/
struct drm_plane *drm_primary_helper_create_plane(struct drm_device *dev,
const uint32_t *formats,
int num_formats)
{ {
struct drm_plane *primary; struct drm_plane *primary;
int ret; int ret;
...@@ -366,17 +353,18 @@ struct drm_plane *drm_primary_helper_create_plane(struct drm_device *dev, ...@@ -366,17 +353,18 @@ struct drm_plane *drm_primary_helper_create_plane(struct drm_device *dev,
if (primary == NULL) { if (primary == NULL) {
DRM_DEBUG_KMS("Failed to allocate primary plane\n"); DRM_DEBUG_KMS("Failed to allocate primary plane\n");
return NULL; return NULL;
} /*
* Remove the format_default field from drm_plane when dropping
if (formats == NULL) { * this helper.
formats = safe_modeset_formats; */
num_formats = ARRAY_SIZE(safe_modeset_formats); primary->format_default = true;
} }
/* possible_crtc's will be filled in later by crtc_init */ /* possible_crtc's will be filled in later by crtc_init */
ret = drm_universal_plane_init(dev, primary, 0, ret = drm_universal_plane_init(dev, primary, 0,
&drm_primary_helper_funcs, &drm_primary_helper_funcs,
formats, num_formats, safe_modeset_formats,
ARRAY_SIZE(safe_modeset_formats),
DRM_PLANE_TYPE_PRIMARY); DRM_PLANE_TYPE_PRIMARY);
if (ret) { if (ret) {
kfree(primary); kfree(primary);
...@@ -385,7 +373,6 @@ struct drm_plane *drm_primary_helper_create_plane(struct drm_device *dev, ...@@ -385,7 +373,6 @@ struct drm_plane *drm_primary_helper_create_plane(struct drm_device *dev,
return primary; return primary;
} }
EXPORT_SYMBOL(drm_primary_helper_create_plane);
/** /**
* drm_crtc_init - Legacy CRTC initialization function * drm_crtc_init - Legacy CRTC initialization function
...@@ -404,7 +391,7 @@ int drm_crtc_init(struct drm_device *dev, struct drm_crtc *crtc, ...@@ -404,7 +391,7 @@ int drm_crtc_init(struct drm_device *dev, struct drm_crtc *crtc,
{ {
struct drm_plane *primary; struct drm_plane *primary;
primary = drm_primary_helper_create_plane(dev, NULL, 0); primary = create_primary_plane(dev);
return drm_crtc_init_with_planes(dev, crtc, primary, NULL, funcs); return drm_crtc_init_with_planes(dev, crtc, primary, NULL, funcs);
} }
EXPORT_SYMBOL(drm_crtc_init); EXPORT_SYMBOL(drm_crtc_init);
......
...@@ -166,23 +166,68 @@ void drm_sysfs_destroy(void) ...@@ -166,23 +166,68 @@ void drm_sysfs_destroy(void)
/* /*
* Connector properties * Connector properties
*/ */
static ssize_t status_show(struct device *device, static ssize_t status_store(struct device *device,
struct device_attribute *attr, struct device_attribute *attr,
char *buf) const char *buf, size_t count)
{ {
struct drm_connector *connector = to_drm_connector(device); struct drm_connector *connector = to_drm_connector(device);
enum drm_connector_status status; struct drm_device *dev = connector->dev;
enum drm_connector_status old_status;
int ret; int ret;
ret = mutex_lock_interruptible(&connector->dev->mode_config.mutex); ret = mutex_lock_interruptible(&dev->mode_config.mutex);
if (ret) if (ret)
return ret; return ret;
status = connector->funcs->detect(connector, true); old_status = connector->status;
mutex_unlock(&connector->dev->mode_config.mutex);
if (sysfs_streq(buf, "detect")) {
connector->force = 0;
connector->status = connector->funcs->detect(connector, true);
} else if (sysfs_streq(buf, "on")) {
connector->force = DRM_FORCE_ON;
} else if (sysfs_streq(buf, "on-digital")) {
connector->force = DRM_FORCE_ON_DIGITAL;
} else if (sysfs_streq(buf, "off")) {
connector->force = DRM_FORCE_OFF;
} else
ret = -EINVAL;
if (ret == 0 && connector->force) {
if (connector->force == DRM_FORCE_ON ||
connector->force == DRM_FORCE_ON_DIGITAL)
connector->status = connector_status_connected;
else
connector->status = connector_status_disconnected;
if (connector->funcs->force)
connector->funcs->force(connector);
}
if (old_status != connector->status) {
DRM_DEBUG_KMS("[CONNECTOR:%d:%s] status updated from %d to %d\n",
connector->base.id,
connector->name,
old_status, connector->status);
dev->mode_config.delayed_event = true;
if (dev->mode_config.poll_enabled)
schedule_delayed_work(&dev->mode_config.output_poll_work,
0);
}
mutex_unlock(&dev->mode_config.mutex);
return ret;
}
static ssize_t status_show(struct device *device,
struct device_attribute *attr,
char *buf)
{
struct drm_connector *connector = to_drm_connector(device);
return snprintf(buf, PAGE_SIZE, "%s\n", return snprintf(buf, PAGE_SIZE, "%s\n",
drm_get_connector_status_name(status)); drm_get_connector_status_name(connector->status));
} }
static ssize_t dpms_show(struct device *device, static ssize_t dpms_show(struct device *device,
...@@ -339,7 +384,7 @@ static ssize_t select_subconnector_show(struct device *device, ...@@ -339,7 +384,7 @@ static ssize_t select_subconnector_show(struct device *device,
drm_get_dvi_i_select_name((int)subconnector)); drm_get_dvi_i_select_name((int)subconnector));
} }
static DEVICE_ATTR_RO(status); static DEVICE_ATTR_RW(status);
static DEVICE_ATTR_RO(enabled); static DEVICE_ATTR_RO(enabled);
static DEVICE_ATTR_RO(dpms); static DEVICE_ATTR_RO(dpms);
static DEVICE_ATTR_RO(modes); static DEVICE_ATTR_RO(modes);
......
...@@ -573,7 +573,7 @@ static void adv7511_encoder_dpms(struct drm_encoder *encoder, int mode) ...@@ -573,7 +573,7 @@ static void adv7511_encoder_dpms(struct drm_encoder *encoder, int mode)
* goes low the adv7511 is reset and the outputs are disabled * goes low the adv7511 is reset and the outputs are disabled
* which might cause the monitor to go to standby again. To * which might cause the monitor to go to standby again. To
* avoid this we ignore the HDP pin for the first few seconds * avoid this we ignore the HDP pin for the first few seconds
* after enabeling the output. * after enabling the output.
*/ */
regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER2, regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER2,
ADV7511_REG_POWER2_HDP_SRC_MASK, ADV7511_REG_POWER2_HDP_SRC_MASK,
......
...@@ -203,16 +203,8 @@ intel_plane_atomic_get_property(struct drm_plane *plane, ...@@ -203,16 +203,8 @@ intel_plane_atomic_get_property(struct drm_plane *plane,
struct drm_property *property, struct drm_property *property,
uint64_t *val) uint64_t *val)
{ {
struct drm_mode_config *config = &plane->dev->mode_config;
if (property == config->rotation_property) {
*val = state->rotation;
} else {
DRM_DEBUG_KMS("Unknown plane property '%s'\n", property->name); DRM_DEBUG_KMS("Unknown plane property '%s'\n", property->name);
return -EINVAL; return -EINVAL;
}
return 0;
} }
/** /**
...@@ -233,14 +225,6 @@ intel_plane_atomic_set_property(struct drm_plane *plane, ...@@ -233,14 +225,6 @@ intel_plane_atomic_set_property(struct drm_plane *plane,
struct drm_property *property, struct drm_property *property,
uint64_t val) uint64_t val)
{ {
struct drm_mode_config *config = &plane->dev->mode_config;
if (property == config->rotation_property) {
state->rotation = val;
} else {
DRM_DEBUG_KMS("Unknown plane property '%s'\n", property->name); DRM_DEBUG_KMS("Unknown plane property '%s'\n", property->name);
return -EINVAL; return -EINVAL;
}
return 0;
} }
...@@ -830,6 +830,7 @@ enum drm_plane_type { ...@@ -830,6 +830,7 @@ enum drm_plane_type {
* @possible_crtcs: pipes this plane can be bound to * @possible_crtcs: pipes this plane can be bound to
* @format_types: array of formats supported by this plane * @format_types: array of formats supported by this plane
* @format_count: number of formats supported * @format_count: number of formats supported
* @format_default: driver hasn't supplied supported formats for the plane
* @crtc: currently bound CRTC * @crtc: currently bound CRTC
* @fb: currently bound fb * @fb: currently bound fb
* @old_fb: Temporary tracking of the old fb while a modeset is ongoing. Used by * @old_fb: Temporary tracking of the old fb while a modeset is ongoing. Used by
...@@ -850,6 +851,7 @@ struct drm_plane { ...@@ -850,6 +851,7 @@ struct drm_plane {
uint32_t possible_crtcs; uint32_t possible_crtcs;
uint32_t *format_types; uint32_t *format_types;
uint32_t format_count; uint32_t format_count;
bool format_default;
struct drm_crtc *crtc; struct drm_crtc *crtc;
struct drm_framebuffer *fb; struct drm_framebuffer *fb;
...@@ -1263,6 +1265,8 @@ extern int drm_plane_init(struct drm_device *dev, ...@@ -1263,6 +1265,8 @@ extern int drm_plane_init(struct drm_device *dev,
extern void drm_plane_cleanup(struct drm_plane *plane); extern void drm_plane_cleanup(struct drm_plane *plane);
extern unsigned int drm_plane_index(struct drm_plane *plane); extern unsigned int drm_plane_index(struct drm_plane *plane);
extern void drm_plane_force_disable(struct drm_plane *plane); extern void drm_plane_force_disable(struct drm_plane *plane);
extern int drm_plane_check_pixel_format(const struct drm_plane *plane,
u32 format);
extern void drm_crtc_get_hv_timing(const struct drm_display_mode *mode, extern void drm_crtc_get_hv_timing(const struct drm_display_mode *mode,
int *hdisplay, int *vdisplay); int *hdisplay, int *vdisplay);
extern int drm_crtc_check_viewport(const struct drm_crtc *crtc, extern int drm_crtc_check_viewport(const struct drm_crtc *crtc,
......
...@@ -92,8 +92,14 @@ ...@@ -92,8 +92,14 @@
# define DP_MSA_TIMING_PAR_IGNORED (1 << 6) /* eDP */ # define DP_MSA_TIMING_PAR_IGNORED (1 << 6) /* eDP */
# define DP_OUI_SUPPORT (1 << 7) # define DP_OUI_SUPPORT (1 << 7)
#define DP_SUPPORTED_LINK_RATES 0x010 /*eDP 1.4*/ #define DP_RECEIVE_PORT_0_CAP_0 0x008
#define DP_MAX_SUPPORTED_RATES 0x8 # define DP_LOCAL_EDID_PRESENT (1 << 1)
# define DP_ASSOCIATED_TO_PRECEDING_PORT (1 << 2)
#define DP_RECEIVE_PORT_0_BUFFER_SIZE 0x009
#define DP_RECEIVE_PORT_1_CAP_0 0x00a
#define DP_RECEIVE_PORT_1_BUFFER_SIZE 0x00b
#define DP_I2C_SPEED_CAP 0x00c /* DPI */ #define DP_I2C_SPEED_CAP 0x00c /* DPI */
# define DP_I2C_SPEED_1K 0x01 # define DP_I2C_SPEED_1K 0x01
...@@ -104,9 +110,19 @@ ...@@ -104,9 +110,19 @@
# define DP_I2C_SPEED_1M 0x20 # define DP_I2C_SPEED_1M 0x20
#define DP_EDP_CONFIGURATION_CAP 0x00d /* XXX 1.2? */ #define DP_EDP_CONFIGURATION_CAP 0x00d /* XXX 1.2? */
# define DP_ALTERNATE_SCRAMBLER_RESET_CAP (1 << 0)
# define DP_FRAMING_CHANGE_CAP (1 << 1)
# define DP_DPCD_DISPLAY_CONTROL_CAPABLE (1 << 3) /* edp v1.2 or higher */ # define DP_DPCD_DISPLAY_CONTROL_CAPABLE (1 << 3) /* edp v1.2 or higher */
#define DP_TRAINING_AUX_RD_INTERVAL 0x00e /* XXX 1.2? */ #define DP_TRAINING_AUX_RD_INTERVAL 0x00e /* XXX 1.2? */
#define DP_ADAPTER_CAP 0x00f /* 1.2 */
# define DP_FORCE_LOAD_SENSE_CAP (1 << 0)
# define DP_ALTERNATE_I2C_PATTERN_CAP (1 << 1)
#define DP_SUPPORTED_LINK_RATES 0x010 /* eDP 1.4 */
# define DP_MAX_SUPPORTED_RATES 8 /* 16-bit little-endian */
/* Multiple stream transport */ /* Multiple stream transport */
#define DP_FAUX_CAP 0x020 /* 1.2 */ #define DP_FAUX_CAP 0x020 /* 1.2 */
# define DP_FAUX_CAP_1 (1 << 0) # define DP_FAUX_CAP_1 (1 << 0)
...@@ -114,10 +130,56 @@ ...@@ -114,10 +130,56 @@
#define DP_MSTM_CAP 0x021 /* 1.2 */ #define DP_MSTM_CAP 0x021 /* 1.2 */
# define DP_MST_CAP (1 << 0) # define DP_MST_CAP (1 << 0)
#define DP_NUMBER_OF_AUDIO_ENDPOINTS 0x022 /* 1.2 */
/* AV_SYNC_DATA_BLOCK 1.2 */
#define DP_AV_GRANULARITY 0x023
# define DP_AG_FACTOR_MASK (0xf << 0)
# define DP_AG_FACTOR_3MS (0 << 0)
# define DP_AG_FACTOR_2MS (1 << 0)
# define DP_AG_FACTOR_1MS (2 << 0)
# define DP_AG_FACTOR_500US (3 << 0)
# define DP_AG_FACTOR_200US (4 << 0)
# define DP_AG_FACTOR_100US (5 << 0)
# define DP_AG_FACTOR_10US (6 << 0)
# define DP_AG_FACTOR_1US (7 << 0)
# define DP_VG_FACTOR_MASK (0xf << 4)
# define DP_VG_FACTOR_3MS (0 << 4)
# define DP_VG_FACTOR_2MS (1 << 4)
# define DP_VG_FACTOR_1MS (2 << 4)
# define DP_VG_FACTOR_500US (3 << 4)
# define DP_VG_FACTOR_200US (4 << 4)
# define DP_VG_FACTOR_100US (5 << 4)
#define DP_AUD_DEC_LAT0 0x024
#define DP_AUD_DEC_LAT1 0x025
#define DP_AUD_PP_LAT0 0x026
#define DP_AUD_PP_LAT1 0x027
#define DP_VID_INTER_LAT 0x028
#define DP_VID_PROG_LAT 0x029
#define DP_REP_LAT 0x02a
#define DP_AUD_DEL_INS0 0x02b
#define DP_AUD_DEL_INS1 0x02c
#define DP_AUD_DEL_INS2 0x02d
/* End of AV_SYNC_DATA_BLOCK */
#define DP_RECEIVER_ALPM_CAP 0x02e /* eDP 1.4 */
# define DP_ALPM_CAP (1 << 0)
#define DP_SINK_DEVICE_AUX_FRAME_SYNC_CAP 0x02f /* eDP 1.4 */
# define DP_AUX_FRAME_SYNC_CAP (1 << 0)
#define DP_GUID 0x030 /* 1.2 */ #define DP_GUID 0x030 /* 1.2 */
#define DP_PSR_SUPPORT 0x070 /* XXX 1.2? */ #define DP_PSR_SUPPORT 0x070 /* XXX 1.2? */
# define DP_PSR_IS_SUPPORTED 1 # define DP_PSR_IS_SUPPORTED 1
# define DP_PSR2_IS_SUPPORTED 2 /* eDP 1.4 */
#define DP_PSR_CAPS 0x071 /* XXX 1.2? */ #define DP_PSR_CAPS 0x071 /* XXX 1.2? */
# define DP_PSR_NO_TRAIN_ON_EXIT 1 # define DP_PSR_NO_TRAIN_ON_EXIT 1
# define DP_PSR_SETUP_TIME_330 (0 << 1) # define DP_PSR_SETUP_TIME_330 (0 << 1)
...@@ -157,6 +219,7 @@ ...@@ -157,6 +219,7 @@
/* link configuration */ /* link configuration */
#define DP_LINK_BW_SET 0x100 #define DP_LINK_BW_SET 0x100
# define DP_LINK_RATE_TABLE 0x00 /* eDP 1.4 */
# define DP_LINK_BW_1_62 0x06 # define DP_LINK_BW_1_62 0x06
# define DP_LINK_BW_2_7 0x0a # define DP_LINK_BW_2_7 0x0a
# define DP_LINK_BW_5_4 0x14 /* 1.2 */ # define DP_LINK_BW_5_4 0x14 /* 1.2 */
...@@ -172,11 +235,12 @@ ...@@ -172,11 +235,12 @@
# define DP_TRAINING_PATTERN_3 3 /* 1.2 */ # define DP_TRAINING_PATTERN_3 3 /* 1.2 */
# define DP_TRAINING_PATTERN_MASK 0x3 # define DP_TRAINING_PATTERN_MASK 0x3
# define DP_LINK_QUAL_PATTERN_DISABLE (0 << 2) /* DPCD 1.1 only. For DPCD >= 1.2 see per-lane DP_LINK_QUAL_LANEn_SET */
# define DP_LINK_QUAL_PATTERN_D10_2 (1 << 2) # define DP_LINK_QUAL_PATTERN_11_DISABLE (0 << 2)
# define DP_LINK_QUAL_PATTERN_ERROR_RATE (2 << 2) # define DP_LINK_QUAL_PATTERN_11_D10_2 (1 << 2)
# define DP_LINK_QUAL_PATTERN_PRBS7 (3 << 2) # define DP_LINK_QUAL_PATTERN_11_ERROR_RATE (2 << 2)
# define DP_LINK_QUAL_PATTERN_MASK (3 << 2) # define DP_LINK_QUAL_PATTERN_11_PRBS7 (3 << 2)
# define DP_LINK_QUAL_PATTERN_11_MASK (3 << 2)
# define DP_RECOVERED_CLOCK_OUT_EN (1 << 4) # define DP_RECOVERED_CLOCK_OUT_EN (1 << 4)
# define DP_LINK_SCRAMBLING_DISABLE (1 << 5) # define DP_LINK_SCRAMBLING_DISABLE (1 << 5)
...@@ -219,19 +283,63 @@ ...@@ -219,19 +283,63 @@
/* bitmask as for DP_I2C_SPEED_CAP */ /* bitmask as for DP_I2C_SPEED_CAP */
#define DP_EDP_CONFIGURATION_SET 0x10a /* XXX 1.2? */ #define DP_EDP_CONFIGURATION_SET 0x10a /* XXX 1.2? */
# define DP_ALTERNATE_SCRAMBLER_RESET_ENABLE (1 << 0)
# define DP_FRAMING_CHANGE_ENABLE (1 << 1)
# define DP_PANEL_SELF_TEST_ENABLE (1 << 7)
#define DP_LINK_QUAL_LANE0_SET 0x10b /* DPCD >= 1.2 */
#define DP_LINK_QUAL_LANE1_SET 0x10c
#define DP_LINK_QUAL_LANE2_SET 0x10d
#define DP_LINK_QUAL_LANE3_SET 0x10e
# define DP_LINK_QUAL_PATTERN_DISABLE 0
# define DP_LINK_QUAL_PATTERN_D10_2 1
# define DP_LINK_QUAL_PATTERN_ERROR_RATE 2
# define DP_LINK_QUAL_PATTERN_PRBS7 3
# define DP_LINK_QUAL_PATTERN_80BIT_CUSTOM 4
# define DP_LINK_QUAL_PATTERN_HBR2_EYE 5
# define DP_LINK_QUAL_PATTERN_MASK 7
#define DP_TRAINING_LANE0_1_SET2 0x10f
#define DP_TRAINING_LANE2_3_SET2 0x110
# define DP_LANE02_POST_CURSOR2_SET_MASK (3 << 0)
# define DP_LANE02_MAX_POST_CURSOR2_REACHED (1 << 2)
# define DP_LANE13_POST_CURSOR2_SET_MASK (3 << 4)
# define DP_LANE13_MAX_POST_CURSOR2_REACHED (1 << 6)
#define DP_MSTM_CTRL 0x111 /* 1.2 */ #define DP_MSTM_CTRL 0x111 /* 1.2 */
# define DP_MST_EN (1 << 0) # define DP_MST_EN (1 << 0)
# define DP_UP_REQ_EN (1 << 1) # define DP_UP_REQ_EN (1 << 1)
# define DP_UPSTREAM_IS_SRC (1 << 2) # define DP_UPSTREAM_IS_SRC (1 << 2)
#define DP_LINK_RATE_SET 0x115 #define DP_AUDIO_DELAY0 0x112 /* 1.2 */
#define DP_AUDIO_DELAY1 0x113
#define DP_AUDIO_DELAY2 0x114
#define DP_LINK_RATE_SET 0x115 /* eDP 1.4 */
# define DP_LINK_RATE_SET_SHIFT 0
# define DP_LINK_RATE_SET_MASK (7 << 0)
#define DP_RECEIVER_ALPM_CONFIG 0x116 /* eDP 1.4 */
# define DP_ALPM_ENABLE (1 << 0)
# define DP_ALPM_LOCK_ERROR_IRQ_HPD_ENABLE (1 << 1)
#define DP_SINK_DEVICE_AUX_FRAME_SYNC_CONF 0x117 /* eDP 1.4 */
# define DP_AUX_FRAME_SYNC_ENABLE (1 << 0)
# define DP_IRQ_HPD_ENABLE (1 << 1)
#define DP_UPSTREAM_DEVICE_DP_PWR_NEED 0x118 /* 1.2 */
# define DP_PWR_NOT_NEEDED (1 << 0)
#define DP_AUX_FRAME_SYNC_VALUE 0x15c /* eDP 1.4 */
# define DP_AUX_FRAME_SYNC_VALID (1 << 0)
#define DP_PSR_EN_CFG 0x170 /* XXX 1.2? */ #define DP_PSR_EN_CFG 0x170 /* XXX 1.2? */
# define DP_PSR_ENABLE (1 << 0) # define DP_PSR_ENABLE (1 << 0)
# define DP_PSR_MAIN_LINK_ACTIVE (1 << 1) # define DP_PSR_MAIN_LINK_ACTIVE (1 << 1)
# define DP_PSR_CRC_VERIFICATION (1 << 2) # define DP_PSR_CRC_VERIFICATION (1 << 2)
# define DP_PSR_FRAME_CAPTURE (1 << 3) # define DP_PSR_FRAME_CAPTURE (1 << 3)
# define DP_PSR_SELECTIVE_UPDATE (1 << 4)
# define DP_PSR_IRQ_HPD_WITH_CRC_ERRORS (1 << 5)
#define DP_ADAPTER_CTRL 0x1a0 #define DP_ADAPTER_CTRL 0x1a0
# define DP_ADAPTER_CTRL_FORCE_LOAD_SENSE (1 << 0) # define DP_ADAPTER_CTRL_FORCE_LOAD_SENSE (1 << 0)
...@@ -338,7 +446,48 @@ ...@@ -338,7 +446,48 @@
# define DP_SET_POWER_D3 0x2 # define DP_SET_POWER_D3 0x2
# define DP_SET_POWER_MASK 0x3 # define DP_SET_POWER_MASK 0x3
#define DP_EDP_DPCD_REV 0x700 #define DP_EDP_DPCD_REV 0x700 /* eDP 1.2 */
# define DP_EDP_11 0x00
# define DP_EDP_12 0x01
# define DP_EDP_13 0x02
# define DP_EDP_14 0x03
#define DP_EDP_GENERAL_CAP_1 0x701
#define DP_EDP_BACKLIGHT_ADJUSTMENT_CAP 0x702
#define DP_EDP_GENERAL_CAP_2 0x703
#define DP_EDP_GENERAL_CAP_3 0x704 /* eDP 1.4 */
#define DP_EDP_DISPLAY_CONTROL_REGISTER 0x720
#define DP_EDP_BACKLIGHT_MODE_SET_REGISTER 0x721
#define DP_EDP_BACKLIGHT_BRIGHTNESS_MSB 0x722
#define DP_EDP_BACKLIGHT_BRIGHTNESS_LSB 0x723
#define DP_EDP_PWMGEN_BIT_COUNT 0x724
#define DP_EDP_PWMGEN_BIT_COUNT_CAP_MIN 0x725
#define DP_EDP_PWMGEN_BIT_COUNT_CAP_MAX 0x726
#define DP_EDP_BACKLIGHT_CONTROL_STATUS 0x727
#define DP_EDP_BACKLIGHT_FREQ_SET 0x728
#define DP_EDP_BACKLIGHT_FREQ_CAP_MIN_MSB 0x72a
#define DP_EDP_BACKLIGHT_FREQ_CAP_MIN_MID 0x72b
#define DP_EDP_BACKLIGHT_FREQ_CAP_MIN_LSB 0x72c
#define DP_EDP_BACKLIGHT_FREQ_CAP_MAX_MSB 0x72d
#define DP_EDP_BACKLIGHT_FREQ_CAP_MAX_MID 0x72e
#define DP_EDP_BACKLIGHT_FREQ_CAP_MAX_LSB 0x72f
#define DP_EDP_DBC_MINIMUM_BRIGHTNESS_SET 0x732
#define DP_EDP_DBC_MAXIMUM_BRIGHTNESS_SET 0x733
#define DP_EDP_REGIONAL_BACKLIGHT_BASE 0x740 /* eDP 1.4 */
#define DP_EDP_REGIONAL_BACKLIGHT_0 0x741 /* eDP 1.4 */
#define DP_SIDEBAND_MSG_DOWN_REQ_BASE 0x1000 /* 1.2 MST */ #define DP_SIDEBAND_MSG_DOWN_REQ_BASE 0x1000 /* 1.2 MST */
#define DP_SIDEBAND_MSG_UP_REP_BASE 0x1200 /* 1.2 MST */ #define DP_SIDEBAND_MSG_UP_REP_BASE 0x1200 /* 1.2 MST */
...@@ -358,6 +507,7 @@ ...@@ -358,6 +507,7 @@
#define DP_PSR_ERROR_STATUS 0x2006 /* XXX 1.2? */ #define DP_PSR_ERROR_STATUS 0x2006 /* XXX 1.2? */
# define DP_PSR_LINK_CRC_ERROR (1 << 0) # define DP_PSR_LINK_CRC_ERROR (1 << 0)
# define DP_PSR_RFB_STORAGE_ERROR (1 << 1) # define DP_PSR_RFB_STORAGE_ERROR (1 << 1)
# define DP_PSR_VSC_SDP_UNCORRECTABLE_ERROR (1 << 2) /* eDP 1.4 */
#define DP_PSR_ESI 0x2007 /* XXX 1.2? */ #define DP_PSR_ESI 0x2007 /* XXX 1.2? */
# define DP_PSR_CAPS_CHANGE (1 << 0) # define DP_PSR_CAPS_CHANGE (1 << 0)
...@@ -371,6 +521,9 @@ ...@@ -371,6 +521,9 @@
# define DP_PSR_SINK_INTERNAL_ERROR 7 # define DP_PSR_SINK_INTERNAL_ERROR 7
# define DP_PSR_SINK_STATE_MASK 0x07 # define DP_PSR_SINK_STATE_MASK 0x07
#define DP_RECEIVER_ALPM_STATUS 0x200b /* eDP 1.4 */
# define DP_ALPM_LOCK_TIMEOUT_ERROR (1 << 0)
/* DP 1.2 Sideband message defines */ /* DP 1.2 Sideband message defines */
/* peer device type - DP 1.2a Table 2-92 */ /* peer device type - DP 1.2a Table 2-92 */
#define DP_PEER_DEVICE_NONE 0x0 #define DP_PEER_DEVICE_NONE 0x0
......
...@@ -100,10 +100,6 @@ extern int drm_primary_helper_update(struct drm_plane *plane, ...@@ -100,10 +100,6 @@ extern int drm_primary_helper_update(struct drm_plane *plane,
extern int drm_primary_helper_disable(struct drm_plane *plane); extern int drm_primary_helper_disable(struct drm_plane *plane);
extern void drm_primary_helper_destroy(struct drm_plane *plane); extern void drm_primary_helper_destroy(struct drm_plane *plane);
extern const struct drm_plane_funcs drm_primary_helper_funcs; extern const struct drm_plane_funcs drm_primary_helper_funcs;
extern struct drm_plane *drm_primary_helper_create_plane(struct drm_device *dev,
const uint32_t *formats,
int num_formats);
int drm_plane_helper_update(struct drm_plane *plane, struct drm_crtc *crtc, int drm_plane_helper_update(struct drm_plane *plane, struct drm_crtc *crtc,
struct drm_framebuffer *fb, struct drm_framebuffer *fb,
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment