ARM: dts: twl6030: Move common configuration for OMAP4 boards in a separate dtsi file

The OMAP4 SoC family uses specially-designed PMIC (power management IC)
companion chip for power management needs: TWL6030/TWL6032.
Therefore there is a typical connection of PMIC to OMAP4 so we can
move it into separate .dtsi file and do not duplicate over
board-specific files.

Tested on OMAP4 SDP board and Pandaboard ES2.
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

arch/arm/boot/dts/omap4-panda-common.dtsi

@@ -122,23 +122,9 @@ wl12xx_vmmc: wl12xx_vmmc {
 	};
 };
 
-&omap4_pmx_wkup {
-	pinctrl-names = "default";
-	pinctrl-0 = <
-			&twl6030_wkup_pins
-	>;
-
-	twl6030_wkup_pins: pinmux_twl6030_wkup_pins {
-		pinctrl-single,pins = <
-			0x14 (PIN_OUTPUT | MUX_MODE2)		/* fref_clk0_out.sys_drm_msecure */
-		>;
-	};
-};
-
 &omap4_pmx_core {
 	pinctrl-names = "default";
 	pinctrl-0 = <
-			&twl6030_pins
 			&twl6040_pins
 			&mcpdm_pins
 			&mcbsp1_pins
@@ -147,12 +133,6 @@ &tpd12s015_pins
 			&hsusbb1_pins
 	>;
 
-	twl6030_pins: pinmux_twl6030_pins {
-		pinctrl-single,pins = <
-			0x15e (WAKEUP_EN | PIN_INPUT_PULLUP | MUX_MODE0)	/* sys_nirq1.sys_nirq1 */
-		>;
-	};
-
 	twl6040_pins: pinmux_twl6040_pins {
 		pinctrl-single,pins = <
 			0xe0 (PIN_OUTPUT | MUX_MODE3)	/* hdq_sio.gpio_127 */
@@ -305,6 +285,7 @@ twl6040: twl@4b {
 };
 
 #include "twl6030.dtsi"
+#include "twl6030_omap4.dtsi"
 
 &i2c2 {
 	pinctrl-names = "default";

arch/arm/boot/dts/omap4-sdp.dts

@@ -155,23 +155,9 @@ wl12xx_vmmc: wl12xx_vmmc {
 	};
 };
 
-&omap4_pmx_wkup {
-	pinctrl-names = "default";
-	pinctrl-0 = <
-			&twl6030_wkup_pins
-	>;
-
-	twl6030_wkup_pins: pinmux_twl6030_wkup_pins {
-		pinctrl-single,pins = <
-			0x14 (PIN_OUTPUT | MUX_MODE2)		/* fref_clk0_out.sys_drm_msecure */
-		>;
-	};
-};
-
 &omap4_pmx_core {
 	pinctrl-names = "default";
 	pinctrl-0 = <
-			&twl6030_pins
 			&twl6040_pins
 			&mcpdm_pins
 			&dmic_pins
@@ -206,12 +192,6 @@ uart4_pins: pinmux_uart4_pins {
 		>;
 	};
 
-	twl6030_pins: pinmux_twl6030_pins {
-		pinctrl-single,pins = <
-			0x15e (WAKEUP_EN | PIN_INPUT_PULLUP | MUX_MODE0)	/* sys_nirq1.sys_nirq1 */
-		>;
-	};
-
 	twl6040_pins: pinmux_twl6040_pins {
 		pinctrl-single,pins = <
 			0xe0 (PIN_OUTPUT | MUX_MODE3)		/* hdq_sio.gpio_127 */
@@ -370,6 +350,7 @@ vibra {
 };
 
 #include "twl6030.dtsi"
+#include "twl6030_omap4.dtsi"
 
 &i2c2 {
 	pinctrl-names = "default";

arch/arm/boot/dts/twl6030_omap4.dtsi

+/*
+ * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+&twl {
+	/*
+	 * On most OMAP4 platforms, the twl6030 IRQ line is connected
+	 * to the SYS_NIRQ1 line on OMAP and the twl6030 MSECURE line is
+	 * connected to the fref_clk0_out.sys_drm_msecure line.
+	 * Therefore, configure the defaults for the SYS_NIRQ1 and
+	 * fref_clk0_out.sys_drm_msecure pins here.
+	 */
+	pinctrl-names = "default";
+	pinctrl-0 = <
+		&twl6030_pins
+		&twl6030_wkup_pins
+	>;
+};
+
+&omap4_pmx_wkup {
+	twl6030_wkup_pins: pinmux_twl6030_wkup_pins {
+		pinctrl-single,pins = <
+			0x14 (PIN_OUTPUT | MUX_MODE2)		/* fref_clk0_out.sys_drm_msecure */
+		>;
+	};
+};
+
+&omap4_pmx_core {
+	twl6030_pins: pinmux_twl6030_pins {
+		pinctrl-single,pins = <
+			0x15e (WAKEUP_EN | PIN_INPUT_PULLUP | MUX_MODE0)	/* sys_nirq1.sys_nirq1 */
+		>;
+	};
+};