ppc64: Add the Kconfig & Makefile changes related to the PowerMac G5 merge

arch/ppc64/Kconfig

@@ -60,7 +60,7 @@ config PPC_ISERIES
 	bool "iSeries"
 
 config PPC_PSERIES
-	bool "pSeries"
+	bool "pSeries / PowerMac G5"
 
 endchoice
 
@@ -72,6 +72,11 @@ config PPC64
 	bool
 	default y
 
+config PPC_OF
+	depends on PPC_PSERIES
+	bool
+	default y
+
 # VMX is pSeries only for now until somebody writes the iSeries
 # exception vectors for it
 config ALTIVEC
@@ -79,6 +84,22 @@ config ALTIVEC
 	depends on PPC_PSERIES
 	default y
 
+config PPC_PMAC
+	depends on PPC_PSERIES
+	bool "Apple PowerMac G5 support"
+
+config PPC_PMAC64
+	bool
+	depends on PPC_PMAC
+	default y
+
+config BOOTX_TEXT
+	bool "Support for early boot text console"
+	depends PPC_OF
+	help
+	  Say Y here to see progress messages from the boot firmware in text
+	  mode. Requires an Open Firmware compatible video card.
+
 config POWER4_ONLY
 	bool "Optimize for POWER4"
 	default n

arch/ppc64/kernel/Makefile

@@ -10,9 +10,11 @@ obj-y               :=	setup.o entry.o traps.o irq.o idle.o \
 			align.o semaphore.o bitops.o stab.o pacaData.o \
 			udbg.o binfmt_elf32.o sys_ppc32.o ioctl32.o \
 			ptrace32.o signal32.o pmc.o rtc.o init_task.o \
-			lmb.o cputable.o
+			lmb.o cputable.o cpu_setup_power4.o idle_power4.o
 
-obj-$(CONFIG_PCI)	+= pci.o pci_dn.o pci_dma.o
+obj-$(CONFIG_PPC_OF) +=	of_device.o
+
+obj-$(CONFIG_PCI)	+= pci.o pci_dn.o pci_dma.o pci_dma_direct.o
 
 ifdef CONFIG_PPC_ISERIES
 obj-$(CONFIG_PCI)	+= iSeries_pci.o iSeries_pci_reset.o \
@@ -27,7 +29,7 @@ obj-$(CONFIG_PPC_ISERIES) += iSeries_irq.o \
 			     proc_pmc.o
 
 obj-$(CONFIG_PPC_PSERIES) += pSeries_pci.o pSeries_lpar.o pSeries_hvCall.o \
-			     eeh.o nvram.o rtasd.o ras.o \
+			     eeh.o nvram.o pSeries_nvram.o rtasd.o ras.o \
 			     open_pic.o xics.o pSeries_htab.o rtas.o \
 			     chrp_setup.o i8259.o prom.o vio.o
 
@@ -40,5 +42,13 @@ obj-$(CONFIG_SCANLOG)		+= scanlog.o
 obj-$(CONFIG_VIOPATH)		+= viopath.o
 obj-$(CONFIG_LPARCFG)		+= lparcfg.o
 obj-$(CONFIG_HVC_CONSOLE)	+= hvconsole.o
+obj-$(CONFIG_BOOTX_TEXT)	+= btext.o
+
+obj-$(CONFIG_PPC_PMAC)		+= pmac_setup.o pmac_feature.o pmac_pci.o \
+				   pmac_time.o pmac_nvram.o pmac_low_i2c.o \
+				   open_pic_u3.o
+ifdef CONFIG_SMP
+obj-$(CONFIG_PPC_PMAC)		+= pmac_smp.o smp-tbsync.o
+endif
 
 CFLAGS_ioctl32.o += -Ifs/

drivers/macintosh/Kconfig

@@ -4,7 +4,7 @@ menu "Macintosh device drivers"
 # we want to change this to something like CONFIG_SYSCTRL_CUDA/PMU
 config ADB_CUDA
 	bool "Support for CUDA based PowerMacs"
-	depends on PPC_PMAC && !POWER4
+	depends on PPC_PMAC && !PPC_PMAC64
 	help
 	  This provides support for CUDA based Power Macintosh systems.  This
 	  includes most OldWorld PowerMacs, the first generation iMacs, the
@@ -69,7 +69,7 @@ config PMAC_BACKLIGHT
 
 config MAC_FLOPPY
 	bool "Support for PowerMac floppy"
-	depends on PPC_PMAC && !POWER4
+	depends on PPC_PMAC && !PPC_PMAC64
 	help
 	  If you have a SWIM-3 (Super Woz Integrated Machine 3; from Apple)
 	  floppy controller, say Y here. Most commonly found in PowerMacs.
@@ -93,7 +93,7 @@ config ADB
 
 config ADB_MACIO
 	bool "Include MacIO (CHRP) ADB driver"
-	depends on ADB && !POWER4
+	depends on ADB && PPC_PMAC && !PPC_PMAC64
 	help
 	  Say Y here to include direct support for the ADB controller in the
 	  Hydra chip used on PowerPC Macintoshes of the CHRP type.  (The Hydra
@@ -129,14 +129,14 @@ config MAC_EMUMOUSEBTN
 
 config THERM_WINDTUNNEL
 	tristate "Support for thermal management on Windtunnel G4s"
-	depends on I2C && I2C_KEYWEST && !POWER4
+	depends on I2C && I2C_KEYWEST && PPC_PMAC && !PPC_PMAC64
 	help
 	  This driver provides some thermostat and fan control for the desktop
 	  G4 "Windtunnel"
 
 config THERM_ADT7467
 	tristate "Support for thermal mgmnt on laptops with ADT 7467 chipset"
-	depends on I2C && I2C_KEYWEST && !POWER4
+	depends on I2C && I2C_KEYWEST && PPC_PMAC && !PPC_PMAC64
 	help
 	  This driver provides some thermostat and fan control for the
           iBook G4, and the ATI based aluminium PowerBooks, allowing slighlty
@@ -144,7 +144,7 @@ config THERM_ADT7467
 
 config THERM_PM72
 	tristate "Support for thermal management on PowerMac G5"
-	depends on I2C && I2C_KEYWEST && POWER4
+	depends on I2C && I2C_KEYWEST && PPC_PMAC64
 	help
 	  This driver provides thermostat and fan control for the desktop
 	  G5 machines.