qed: Add Light L2 support

Other protocols beside the networking driver need the ability
of passing some L2 traffic, usually [although not limited] for the
purpose of some management traffic.
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: Ram Amrani <Ram.Amrani@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ethernet/qlogic/Kconfig

@@ -88,6 +88,14 @@ config QED
 	---help---
 	  This enables the support for ...
 
+config QED_LL2
+	bool "Qlogic QED Light L2 interface"
+	default n
+	depends on QED
+	---help---
+	This enables support for Light L2 interface which is required
+	by all qed protocol drivers other than qede.
+
 config QED_SRIOV
 	bool "QLogic QED 25/40/100Gb SR-IOV support"
 	depends on QED && PCI_IOV

drivers/net/ethernet/qlogic/qed/Makefile

@@ -4,3 +4,4 @@ qed-y := qed_cxt.o qed_dev.o qed_hw.o qed_init_fw_funcs.o qed_init_ops.o \
 	 qed_int.o qed_main.o qed_mcp.o qed_sp_commands.o qed_spq.o qed_l2.o \
 	 qed_selftest.o qed_dcbx.o qed_debug.o
 qed-$(CONFIG_QED_SRIOV) += qed_sriov.o qed_vf.o
+qed-$(CONFIG_QED_LL2) += qed_ll2.o

drivers/net/ethernet/qlogic/qed/qed.h

@@ -72,6 +72,7 @@ struct qed_sb_info;
 struct qed_sb_attn_info;
 struct qed_cxt_mngr;
 struct qed_sb_sp_info;
+struct qed_ll2_info;
 struct qed_mcp_info;
 
 struct qed_rt_data {
@@ -152,6 +153,7 @@ enum QED_RESOURCES {
 	QED_MAC,
 	QED_VLAN,
 	QED_ILT,
+	QED_LL2_QUEUE,
 	QED_MAX_RESC,
 };
 
@@ -360,6 +362,8 @@ struct qed_hwfn {
 	struct qed_sb_attn_info		*p_sb_attn;
 
 	/* Protocol related */
+	bool				using_ll2;
+	struct qed_ll2_info		*p_ll2_info;
 	struct qed_pf_params		pf_params;
 
 	bool b_rdma_enabled_in_prs;
@@ -564,6 +568,11 @@ struct qed_dev {
 
 	struct qed_dbg_params		dbg_params;
 
+#ifdef CONFIG_QED_LL2
+	struct qed_cb_ll2_info		*ll2;
+	u8				ll2_mac_address[ETH_ALEN];
+#endif
+
 	const struct firmware		*firmware;
 };
 

drivers/net/ethernet/qlogic/qed/qed_cxt.c

@@ -1839,6 +1839,8 @@ int qed_cxt_set_pf_params(struct qed_hwfn *p_hwfn)
 	/* Set the number of required CORE connections */
 	u32 core_cids = 1; /* SPQ */
 
+	if (p_hwfn->using_ll2)
+		core_cids += 4;
 	qed_cxt_set_proto_cid_count(p_hwfn, PROTOCOLID_CORE, core_cids, 0);
 
 	switch (p_hwfn->hw_info.personality) {

drivers/net/ethernet/qlogic/qed/qed_dev.c

@@ -29,6 +29,7 @@
 #include "qed_hw.h"
 #include "qed_init_ops.h"
 #include "qed_int.h"
+#include "qed_ll2.h"
 #include "qed_mcp.h"
 #include "qed_reg_addr.h"
 #include "qed_sp.h"
@@ -147,6 +148,9 @@ void qed_resc_free(struct qed_dev *cdev)
 		qed_eq_free(p_hwfn, p_hwfn->p_eq);
 		qed_consq_free(p_hwfn, p_hwfn->p_consq);
 		qed_int_free(p_hwfn);
+#ifdef CONFIG_QED_LL2
+		qed_ll2_free(p_hwfn, p_hwfn->p_ll2_info);
+#endif
 		qed_iov_free(p_hwfn);
 		qed_dmae_info_free(p_hwfn);
 		qed_dcbx_info_free(p_hwfn, p_hwfn->p_dcbx_info);
@@ -403,6 +407,9 @@ int qed_qm_reconf(struct qed_hwfn *p_hwfn, struct qed_ptt *p_ptt)
 
 int qed_resc_alloc(struct qed_dev *cdev)
 {
+#ifdef CONFIG_QED_LL2
+	struct qed_ll2_info *p_ll2_info;
+#endif
 	struct qed_consq *p_consq;
 	struct qed_eq *p_eq;
 	int i, rc = 0;
@@ -513,6 +520,15 @@ int qed_resc_alloc(struct qed_dev *cdev)
 			goto alloc_no_mem;
 		p_hwfn->p_consq = p_consq;
 
+#ifdef CONFIG_QED_LL2
+		if (p_hwfn->using_ll2) {
+			p_ll2_info = qed_ll2_alloc(p_hwfn);
+			if (!p_ll2_info)
+				goto alloc_no_mem;
+			p_hwfn->p_ll2_info = p_ll2_info;
+		}
+#endif
+
 		/* DMA info initialization */
 		rc = qed_dmae_info_alloc(p_hwfn);
 		if (rc)
@@ -561,6 +577,10 @@ void qed_resc_setup(struct qed_dev *cdev)
 		qed_int_setup(p_hwfn, p_hwfn->p_main_ptt);
 
 		qed_iov_setup(p_hwfn, p_hwfn->p_main_ptt);
+#ifdef CONFIG_QED_LL2
+		if (p_hwfn->using_ll2)
+			qed_ll2_setup(p_hwfn, p_hwfn->p_ll2_info);
+#endif
 	}
 }
 
@@ -1304,6 +1324,7 @@ static int qed_hw_get_resc(struct qed_hwfn *p_hwfn)
 	resc_num[QED_VLAN] = (ETH_NUM_VLAN_FILTERS - 1 /*For vlan0*/) /
 			     num_funcs;
 	resc_num[QED_ILT] = PXP_NUM_ILT_RECORDS_BB / num_funcs;
+	resc_num[QED_LL2_QUEUE] = MAX_NUM_LL2_RX_QUEUES / num_funcs;
 
 	for (i = 0; i < QED_MAX_RESC; i++)
 		resc_start[i] = resc_num[i] * enabled_func_idx;
@@ -1327,7 +1348,8 @@ static int qed_hw_get_resc(struct qed_hwfn *p_hwfn)
 		   "RL = %d start = %d\n"
 		   "MAC = %d start = %d\n"
 		   "VLAN = %d start = %d\n"
-		   "ILT = %d start = %d\n",
+		   "ILT = %d start = %d\n"
+		   "LL2_QUEUE = %d start = %d\n",
 		   p_hwfn->hw_info.resc_num[QED_SB],
 		   p_hwfn->hw_info.resc_start[QED_SB],
 		   p_hwfn->hw_info.resc_num[QED_L2_QUEUE],
@@ -1343,7 +1365,9 @@ static int qed_hw_get_resc(struct qed_hwfn *p_hwfn)
 		   p_hwfn->hw_info.resc_num[QED_VLAN],
 		   p_hwfn->hw_info.resc_start[QED_VLAN],
 		   p_hwfn->hw_info.resc_num[QED_ILT],
-		   p_hwfn->hw_info.resc_start[QED_ILT]);
+		   p_hwfn->hw_info.resc_start[QED_ILT],
+		   RESC_NUM(p_hwfn, QED_LL2_QUEUE),
+		   RESC_START(p_hwfn, QED_LL2_QUEUE));
 
 	return 0;
 }
@@ -2133,6 +2157,98 @@ int qed_fw_rss_eng(struct qed_hwfn *p_hwfn, u8 src_id, u8 *dst_id)
 	return 0;
 }
 
+static void qed_llh_mac_to_filter(u32 *p_high, u32 *p_low,
+				  u8 *p_filter)
+{
+	*p_high = p_filter[1] | (p_filter[0] << 8);
+	*p_low = p_filter[5] | (p_filter[4] << 8) |
+		 (p_filter[3] << 16) | (p_filter[2] << 24);
+}
+
+int qed_llh_add_mac_filter(struct qed_hwfn *p_hwfn,
+			   struct qed_ptt *p_ptt, u8 *p_filter)
+{
+	u32 high = 0, low = 0, en;
+	int i;
+
+	if (!(IS_MF_SI(p_hwfn) || IS_MF_DEFAULT(p_hwfn)))
+		return 0;
+
+	qed_llh_mac_to_filter(&high, &low, p_filter);
+
+	/* Find a free entry and utilize it */
+	for (i = 0; i < NIG_REG_LLH_FUNC_FILTER_EN_SIZE; i++) {
+		en = qed_rd(p_hwfn, p_ptt,
+			    NIG_REG_LLH_FUNC_FILTER_EN + i * sizeof(u32));
+		if (en)
+			continue;
+		qed_wr(p_hwfn, p_ptt,
+		       NIG_REG_LLH_FUNC_FILTER_VALUE +
+		       2 * i * sizeof(u32), low);
+		qed_wr(p_hwfn, p_ptt,
+		       NIG_REG_LLH_FUNC_FILTER_VALUE +
+		       (2 * i + 1) * sizeof(u32), high);
+		qed_wr(p_hwfn, p_ptt,
+		       NIG_REG_LLH_FUNC_FILTER_MODE + i * sizeof(u32), 0);
+		qed_wr(p_hwfn, p_ptt,
+		       NIG_REG_LLH_FUNC_FILTER_PROTOCOL_TYPE +
+		       i * sizeof(u32), 0);
+		qed_wr(p_hwfn, p_ptt,
+		       NIG_REG_LLH_FUNC_FILTER_EN + i * sizeof(u32), 1);
+		break;
+	}
+	if (i >= NIG_REG_LLH_FUNC_FILTER_EN_SIZE) {
+		DP_NOTICE(p_hwfn,
+			  "Failed to find an empty LLH filter to utilize\n");
+		return -EINVAL;
+	}
+
+	DP_VERBOSE(p_hwfn, NETIF_MSG_HW,
+		   "mac: %pM is added at %d\n",
+		   p_filter, i);
+
+	return 0;
+}
+
+void qed_llh_remove_mac_filter(struct qed_hwfn *p_hwfn,
+			       struct qed_ptt *p_ptt, u8 *p_filter)
+{
+	u32 high = 0, low = 0;
+	int i;
+
+	if (!(IS_MF_SI(p_hwfn) || IS_MF_DEFAULT(p_hwfn)))
+		return;
+
+	qed_llh_mac_to_filter(&high, &low, p_filter);
+
+	/* Find the entry and clean it */
+	for (i = 0; i < NIG_REG_LLH_FUNC_FILTER_EN_SIZE; i++) {
+		if (qed_rd(p_hwfn, p_ptt,
+			   NIG_REG_LLH_FUNC_FILTER_VALUE +
+			   2 * i * sizeof(u32)) != low)
+			continue;
+		if (qed_rd(p_hwfn, p_ptt,
+			   NIG_REG_LLH_FUNC_FILTER_VALUE +
+			   (2 * i + 1) * sizeof(u32)) != high)
+			continue;
+
+		qed_wr(p_hwfn, p_ptt,
+		       NIG_REG_LLH_FUNC_FILTER_EN + i * sizeof(u32), 0);
+		qed_wr(p_hwfn, p_ptt,
+		       NIG_REG_LLH_FUNC_FILTER_VALUE + 2 * i * sizeof(u32), 0);
+		qed_wr(p_hwfn, p_ptt,
+		       NIG_REG_LLH_FUNC_FILTER_VALUE +
+		       (2 * i + 1) * sizeof(u32), 0);
+
+		DP_VERBOSE(p_hwfn, NETIF_MSG_HW,
+			   "mac: %pM is removed from %d\n",
+			   p_filter, i);
+		break;
+	}
+	if (i >= NIG_REG_LLH_FUNC_FILTER_EN_SIZE)
+		DP_NOTICE(p_hwfn, "Tried to remove a non-configured filter\n");
+}
+
 static int qed_set_coalesce(struct qed_hwfn *p_hwfn, struct qed_ptt *p_ptt,
 			    u32 hw_addr, void *p_eth_qzone,
 			    size_t eth_qzone_size, u8 timeset)

drivers/net/ethernet/qlogic/qed/qed_dev_api.h

@@ -309,6 +309,26 @@ int qed_fw_rss_eng(struct qed_hwfn *p_hwfn,
 		   u8 src_id,
 		   u8 *dst_id);
 
+/**
+ * @brief qed_llh_add_mac_filter - configures a MAC filter in llh
+ *
+ * @param p_hwfn
+ * @param p_ptt
+ * @param p_filter - MAC to add
+ */
+int qed_llh_add_mac_filter(struct qed_hwfn *p_hwfn,
+			   struct qed_ptt *p_ptt, u8 *p_filter);
+
+/**
+ * @brief qed_llh_remove_mac_filter - removes a MAC filter from llh
+ *
+ * @param p_hwfn
+ * @param p_ptt
+ * @param p_filter - MAC to remove
+ */
+void qed_llh_remove_mac_filter(struct qed_hwfn *p_hwfn,
+			       struct qed_ptt *p_ptt, u8 *p_filter);
+
 /**
  * *@brief Cleanup of previous driver remains prior to load
  *

drivers/net/ethernet/qlogic/qed/qed_ll2.h

+/* QLogic qed NIC Driver
+ *
+ * Copyright (c) 2015 QLogic Corporation
+ *
+ * This software is available under the terms of the GNU General Public License
+ * (GPL) Version 2, available from the file COPYING in the main directory of
+ * this source tree.
+ */
+
+#ifndef _QED_LL2_H
+#define _QED_LL2_H
+
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/list.h>
+#include <linux/mutex.h>
+#include <linux/slab.h>
+#include <linux/spinlock.h>
+#include <linux/qed/qed_chain.h>
+#include <linux/qed/qed_ll2_if.h>
+#include "qed.h"
+#include "qed_hsi.h"
+#include "qed_sp.h"
+
+#define QED_MAX_NUM_OF_LL2_CONNECTIONS                    (4)
+
+enum qed_ll2_conn_type {
+	QED_LL2_TYPE_RESERVED,
+	QED_LL2_TYPE_ISCSI,
+	QED_LL2_TYPE_TEST,
+	QED_LL2_TYPE_ISCSI_OOO,
+	QED_LL2_TYPE_RESERVED2,
+	QED_LL2_TYPE_ROCE,
+	QED_LL2_TYPE_RESERVED3,
+	MAX_QED_LL2_RX_CONN_TYPE
+};
+
+struct qed_ll2_rx_packet {
+	struct list_head list_entry;
+	struct core_rx_bd_with_buff_len *rxq_bd;
+	dma_addr_t rx_buf_addr;
+	u16 buf_length;
+	void *cookie;
+	u8 placement_offset;
+	u16 parse_flags;
+	u16 packet_length;
+	u16 vlan;
+	u32 opaque_data[2];
+};
+
+struct qed_ll2_tx_packet {
+	struct list_head list_entry;
+	u16 bd_used;
+	u16 vlan;
+	u16 l4_hdr_offset_w;
+	u8 bd_flags;
+	bool notify_fw;
+	void *cookie;
+
+	struct {
+		struct core_tx_bd *txq_bd;
+		dma_addr_t tx_frag;
+		u16 frag_len;
+	} bds_set[ETH_TX_MAX_BDS_PER_NON_LSO_PACKET];
+};
+
+struct qed_ll2_rx_queue {
+	/* Lock protecting the Rx queue manipulation */
+	spinlock_t lock;
+	struct qed_chain rxq_chain;
+	struct qed_chain rcq_chain;
+	u8 rx_sb_index;
+	bool b_cb_registred;
+	__le16 *p_fw_cons;
+	struct list_head active_descq;
+	struct list_head free_descq;
+	struct list_head posting_descq;
+	struct qed_ll2_rx_packet *descq_array;
+	void __iomem *set_prod_addr;
+};
+
+struct qed_ll2_tx_queue {
+	/* Lock protecting the Tx queue manipulation */
+	spinlock_t lock;
+	struct qed_chain txq_chain;
+	u8 tx_sb_index;
+	bool b_cb_registred;
+	__le16 *p_fw_cons;
+	struct list_head active_descq;
+	struct list_head free_descq;
+	struct list_head sending_descq;
+	struct qed_ll2_tx_packet *descq_array;
+	struct qed_ll2_tx_packet *cur_send_packet;
+	struct qed_ll2_tx_packet cur_completing_packet;
+	u16 cur_completing_bd_idx;
+	void __iomem *doorbell_addr;
+	u16 bds_idx;
+	u16 cur_send_frag_num;
+	u16 cur_completing_frag_num;
+	bool b_completing_packet;
+};
+
+struct qed_ll2_info {
+	/* Lock protecting the state of LL2 */
+	struct mutex mutex;
+	enum qed_ll2_conn_type conn_type;
+	u32 cid;
+	u8 my_id;
+	u8 queue_id;
+	u8 tx_stats_id;
+	bool b_active;
+	u16 mtu;
+	u8 rx_drop_ttl0_flg;
+	u8 rx_vlan_removal_en;
+	u8 tx_tc;
+	enum core_tx_dest tx_dest;
+	enum core_error_handle ai_err_packet_too_big;
+	enum core_error_handle ai_err_no_buf;
+	u8 tx_stats_en;
+	struct qed_ll2_rx_queue rx_queue;
+	struct qed_ll2_tx_queue tx_queue;
+};
+
+/**
+ * @brief qed_ll2_acquire_connection - allocate resources,
+ *        starts rx & tx (if relevant) queues pair. Provides
+ *        connecion handler as output parameter.
+ *
+ * @param p_hwfn
+ * @param p_params		Contain various configuration properties
+ * @param rx_num_desc
+ * @param tx_num_desc
+ *
+ * @param p_connection_handle  Output container for LL2 connection's handle
+ *
+ * @return 0 on success, failure otherwise
+ */
+int qed_ll2_acquire_connection(struct qed_hwfn *p_hwfn,
+			       struct qed_ll2_info *p_params,
+			       u16 rx_num_desc,
+			       u16 tx_num_desc,
+			       u8 *p_connection_handle);
+
+/**
+ * @brief qed_ll2_establish_connection - start previously
+ *        allocated LL2 queues pair
+ *
+ * @param p_hwfn
+ * @param p_ptt
+ * @param connection_handle	LL2 connection's handle obtained from
+ *                              qed_ll2_require_connection
+ *
+ * @return 0 on success, failure otherwise
+ */
+int qed_ll2_establish_connection(struct qed_hwfn *p_hwfn, u8 connection_handle);
+
+/**
+ * @brief qed_ll2_post_rx_buffers - submit buffers to LL2 Rx queue.
+ *
+ * @param p_hwfn
+ * @param connection_handle	LL2 connection's handle obtained from
+ *				qed_ll2_require_connection
+ * @param addr			rx (physical address) buffers to submit
+ * @param cookie
+ * @param notify_fw		produce corresponding Rx BD immediately
+ *
+ * @return 0 on success, failure otherwise
+ */
+int qed_ll2_post_rx_buffer(struct qed_hwfn *p_hwfn,
+			   u8 connection_handle,
+			   dma_addr_t addr,
+			   u16 buf_len, void *cookie, u8 notify_fw);
+
+/**
+ * @brief qed_ll2_prepare_tx_packet - request for start Tx BD
+ *				      to prepare Tx packet submission to FW.
+ *
+ * @param p_hwfn
+ * @param connection_handle	LL2 connection's handle obtained from
+ *				qed_ll2_require_connection
+ * @param num_of_bds		a number of requested BD equals a number of
+ *				fragments in Tx packet
+ * @param vlan			VLAN to insert to packet (if insertion set)
+ * @param bd_flags
+ * @param l4_hdr_offset_w	L4 Header Offset from start of packet
+ *				(in words). This is needed if both l4_csum
+ *				and ipv6_ext are set
+ * @param first_frag
+ * @param first_frag_len
+ * @param cookie
+ *
+ * @param notify_fw
+ *
+ * @return 0 on success, failure otherwise
+ */
+int qed_ll2_prepare_tx_packet(struct qed_hwfn *p_hwfn,
+			      u8 connection_handle,
+			      u8 num_of_bds,
+			      u16 vlan,
+			      u8 bd_flags,
+			      u16 l4_hdr_offset_w,
+			      dma_addr_t first_frag,
+			      u16 first_frag_len, void *cookie, u8 notify_fw);
+
+/**
+ * @brief qed_ll2_release_connection -	releases resources
+ *					allocated for LL2 connection
+ *
+ * @param p_hwfn
+ * @param connection_handle		LL2 connection's handle obtained from
+ *					qed_ll2_require_connection
+ */
+void qed_ll2_release_connection(struct qed_hwfn *p_hwfn, u8 connection_handle);
+
+/**
+ * @brief qed_ll2_set_fragment_of_tx_packet -	provides fragments to fill
+ *						Tx BD of BDs requested by
+ *						qed_ll2_prepare_tx_packet
+ *
+ * @param p_hwfn
+ * @param connection_handle			LL2 connection's handle
+ *						obtained from
+ *						qed_ll2_require_connection
+ * @param addr
+ * @param nbytes
+ *
+ * @return 0 on success, failure otherwise
+ */
+int qed_ll2_set_fragment_of_tx_packet(struct qed_hwfn *p_hwfn,
+				      u8 connection_handle,
+				      dma_addr_t addr, u16 nbytes);
+
+/**
+ * @brief qed_ll2_terminate_connection -	stops Tx/Rx queues
+ *
+ *
+ * @param p_hwfn
+ * @param connection_handle			LL2 connection's handle
+ *						obtained from
+ *						qed_ll2_require_connection
+ *
+ * @return 0 on success, failure otherwise
+ */
+int qed_ll2_terminate_connection(struct qed_hwfn *p_hwfn, u8 connection_handle);
+
+/**
+ * @brief qed_ll2_get_stats -	get LL2 queue's statistics
+ *
+ *
+ * @param p_hwfn
+ * @param connection_handle	LL2 connection's handle obtained from
+ *				qed_ll2_require_connection
+ * @param p_stats
+ *
+ * @return 0 on success, failure otherwise
+ */
+int qed_ll2_get_stats(struct qed_hwfn *p_hwfn,
+		      u8 connection_handle, struct qed_ll2_stats *p_stats);
+
+/**
+ * @brief qed_ll2_alloc - Allocates LL2 connections set
+ *
+ * @param p_hwfn
+ *
+ * @return pointer to alocated qed_ll2_info or NULL
+ */
+struct qed_ll2_info *qed_ll2_alloc(struct qed_hwfn *p_hwfn);
+
+/**
+ * @brief qed_ll2_setup - Inits LL2 connections set
+ *
+ * @param p_hwfn
+ * @param p_ll2_connections
+ *
+ */
+void qed_ll2_setup(struct qed_hwfn *p_hwfn,
+		   struct qed_ll2_info *p_ll2_connections);
+
+/**
+ * @brief qed_ll2_free - Releases LL2 connections set
+ *
+ * @param p_hwfn
+ * @param p_ll2_connections
+ *
+ */
+void qed_ll2_free(struct qed_hwfn *p_hwfn,
+		  struct qed_ll2_info *p_ll2_connections);
+
+#endif

drivers/net/ethernet/qlogic/qed/qed_main.c

@@ -22,11 +22,13 @@
 #include <linux/etherdevice.h>
 #include <linux/vmalloc.h>
 #include <linux/qed/qed_if.h>
+#include <linux/qed/qed_ll2_if.h>
 
 #include "qed.h"
 #include "qed_sriov.h"
 #include "qed_sp.h"
 #include "qed_dev_api.h"
+#include "qed_ll2.h"
 #include "qed_mcp.h"
 #include "qed_hw.h"
 #include "qed_selftest.h"
@@ -608,7 +610,16 @@ static int qed_nic_reset(struct qed_dev *cdev)
 
 static int qed_nic_setup(struct qed_dev *cdev)
 {
-	int rc;
+	int rc, i;
+
+	/* Determine if interface is going to require LL2 */
+	if (QED_LEADING_HWFN(cdev)->hw_info.personality != QED_PCI_ETH) {
+		for (i = 0; i < cdev->num_hwfns; i++) {
+			struct qed_hwfn *p_hwfn = &cdev->hwfns[i];
+
+			p_hwfn->using_ll2 = true;
+		}
+	}
 
 	rc = qed_resc_alloc(cdev);
 	if (rc)
@@ -873,6 +884,12 @@ static int qed_slowpath_start(struct qed_dev *cdev,
 	DP_INFO(cdev,
 		"HW initialization and function start completed successfully\n");
 
+	/* Allocate LL2 interface if needed */
+	if (QED_LEADING_HWFN(cdev)->using_ll2) {
+		rc = qed_ll2_alloc_if(cdev);
+		if (rc)
+			goto err3;
+	}
 	if (IS_PF(cdev)) {
 		hwfn = QED_LEADING_HWFN(cdev);
 		drv_version.version = (params->drv_major << 24) |
@@ -893,6 +910,8 @@ static int qed_slowpath_start(struct qed_dev *cdev,
 
 	return 0;
 
+err3:
+	qed_hw_stop(cdev);
 err2:
 	qed_hw_timers_stop_all(cdev);
 	if (IS_PF(cdev))
@@ -915,6 +934,8 @@ static int qed_slowpath_stop(struct qed_dev *cdev)
 	if (!cdev)
 		return -ENODEV;
 
+	qed_ll2_dealloc_if(cdev);
+
 	if (IS_PF(cdev)) {
 		qed_free_stream_mem(cdev);
 		if (IS_QED_ETH_IF(cdev))

drivers/net/ethernet/qlogic/qed/qed_reg_addr.h

@@ -208,6 +208,26 @@
 	0x50196cUL
 #define NIG_REG_LLH_CLS_TYPE_DUALMODE \
 	0x501964UL
+#define NIG_REG_LLH_FUNC_FILTER_VALUE \
+	0x501a00UL
+#define NIG_REG_LLH_FUNC_FILTER_VALUE_SIZE \
+	32
+#define NIG_REG_LLH_FUNC_FILTER_EN \
+	0x501a80UL
+#define NIG_REG_LLH_FUNC_FILTER_EN_SIZE	\
+	16
+#define NIG_REG_LLH_FUNC_FILTER_MODE \
+	0x501ac0UL
+#define NIG_REG_LLH_FUNC_FILTER_MODE_SIZE \
+	16
+#define NIG_REG_LLH_FUNC_FILTER_PROTOCOL_TYPE \
+	0x501b00UL
+#define NIG_REG_LLH_FUNC_FILTER_PROTOCOL_TYPE_SIZE \
+	16
+#define NIG_REG_LLH_FUNC_FILTER_HDR_SEL	\
+	0x501b40UL
+#define NIG_REG_LLH_FUNC_FILTER_HDR_SEL_SIZE \
+	16
 #define  NCSI_REG_CONFIG	\
 	0x040200UL
 #define  PBF_REG_INIT \
@@ -264,6 +284,8 @@
 	0x1f0a1cUL
 #define PRS_REG_ROCE_DEST_QP_MAX_PF \
 	0x1f0430UL
+#define PRS_REG_USE_LIGHT_L2 \
+	0x1f096cUL
 #define  PSDM_REG_ENABLE_IN1 \
 	0xfa0004UL
 #define  PSEM_REG_ENABLE_IN \

drivers/net/ethernet/qlogic/qed/qed_sp.h

@@ -61,6 +61,10 @@ union ramrod_data {
 	struct vport_start_ramrod_data vport_start;
 	struct vport_stop_ramrod_data vport_stop;
 	struct vport_update_ramrod_data vport_update;
+	struct core_rx_start_ramrod_data core_rx_queue_start;
+	struct core_rx_stop_ramrod_data core_rx_queue_stop;
+	struct core_tx_start_ramrod_data core_tx_queue_start;
+	struct core_tx_stop_ramrod_data core_tx_queue_stop;
 	struct vport_filter_update_ramrod_data vport_filter_update;
 
 	struct rdma_init_func_ramrod_data rdma_init_func;

include/linux/qed/qed_if.h

@@ -627,6 +627,7 @@ enum DP_MODULE {
 	QED_MSG_SP	= 0x100000,
 	QED_MSG_STORAGE = 0x200000,
 	QED_MSG_CXT	= 0x800000,
+	QED_MSG_LL2	= 0x1000000,
 	QED_MSG_ILT	= 0x2000000,
 	QED_MSG_ROCE	= 0x4000000,
 	QED_MSG_DEBUG	= 0x8000000,

include/linux/qed/qed_ll2_if.h

+/* QLogic qed NIC Driver
+ *
+ * Copyright (c) 2015 QLogic Corporation
+ *
+ * This software is available under the terms of the GNU General Public License
+ * (GPL) Version 2, available from the file COPYING in the main directory of
+ * this source tree.
+ */
+
+#ifndef _QED_LL2_IF_H
+#define _QED_LL2_IF_H
+
+#include <linux/types.h>
+#include <linux/interrupt.h>
+#include <linux/netdevice.h>
+#include <linux/pci.h>
+#include <linux/skbuff.h>
+#include <linux/version.h>
+#include <linux/kernel.h>
+#include <linux/slab.h>
+#include <linux/qed/qed_if.h>
+
+struct qed_ll2_stats {
+	u64 gsi_invalid_hdr;
+	u64 gsi_invalid_pkt_length;
+	u64 gsi_unsupported_pkt_typ;
+	u64 gsi_crcchksm_error;
+
+	u64 packet_too_big_discard;
+	u64 no_buff_discard;
+
+	u64 rcv_ucast_bytes;
+	u64 rcv_mcast_bytes;
+	u64 rcv_bcast_bytes;
+	u64 rcv_ucast_pkts;
+	u64 rcv_mcast_pkts;
+	u64 rcv_bcast_pkts;
+
+	u64 sent_ucast_bytes;
+	u64 sent_mcast_bytes;
+	u64 sent_bcast_bytes;
+	u64 sent_ucast_pkts;
+	u64 sent_mcast_pkts;
+	u64 sent_bcast_pkts;
+};
+
+#define QED_LL2_UNUSED_HANDLE   (0xff)
+
+struct qed_ll2_cb_ops {
+	int (*rx_cb)(void *, struct sk_buff *, u32, u32);
+	int (*tx_cb)(void *, struct sk_buff *, bool);
+};
+
+struct qed_ll2_params {
+	u16 mtu;
+	bool drop_ttl0_packets;
+	bool rx_vlan_stripping;
+	u8 tx_tc;
+	bool frags_mapped;
+	u8 ll2_mac_address[ETH_ALEN];
+};
+
+struct qed_ll2_ops {
+/**
+ * @brief start - initializes ll2
+ *
+ * @param cdev
+ * @param params - protocol driver configuration for the ll2.
+ *
+ * @return 0 on success, otherwise error value.
+ */
+	int (*start)(struct qed_dev *cdev, struct qed_ll2_params *params);
+
+/**
+ * @brief stop - stops the ll2
+ *
+ * @param cdev
+ *
+ * @return 0 on success, otherwise error value.
+ */
+	int (*stop)(struct qed_dev *cdev);
+
+/**
+ * @brief start_xmit - transmits an skb over the ll2 interface
+ *
+ * @param cdev
+ * @param skb
+ *
+ * @return 0 on success, otherwise error value.
+ */
+	int (*start_xmit)(struct qed_dev *cdev, struct sk_buff *skb);
+
+/**
+ * @brief register_cb_ops - protocol driver register the callback for Rx/Tx
+ * packets. Should be called before `start'.
+ *
+ * @param cdev
+ * @param cookie - to be passed to the callback functions.
+ * @param ops - the callback functions to register for Rx / Tx.
+ *
+ * @return 0 on success, otherwise error value.
+ */
+	void (*register_cb_ops)(struct qed_dev *cdev,
+				const struct qed_ll2_cb_ops *ops,
+				void *cookie);
+
+/**
+ * @brief get LL2 related statistics
+ *
+ * @param cdev
+ * @param stats - pointer to struct that would be filled with stats
+ *
+ * @return 0 on success, error otherwise.
+ */
+	int (*get_stats)(struct qed_dev *cdev, struct qed_ll2_stats *stats);
+};
+
+#ifdef CONFIG_QED_LL2
+int qed_ll2_alloc_if(struct qed_dev *);
+void qed_ll2_dealloc_if(struct qed_dev *);
+#else
+static const struct qed_ll2_ops qed_ll2_ops_pass = {
+	.start = NULL,
+	.stop = NULL,
+	.start_xmit = NULL,
+	.register_cb_ops = NULL,
+	.get_stats = NULL,
+};
+
+static inline int qed_ll2_alloc_if(struct qed_dev *cdev)
+{
+	return 0;
+}
+
+static inline void qed_ll2_dealloc_if(struct qed_dev *cdev)
+{
+}
+#endif
+#endif