Commit 0abc676e authored by David S. Miller's avatar David S. Miller

Merge branch 'mvpp2-phylink-fixes'

Russell King says:

====================
mvpp2 phylink fixes

Having spent a while debugging issues with Sven Auhagen, it appears
that the mvpp2 network driver's phylink support isn't quite correct.

This series fixes that up, but, despite being tested locally, by
Sven, and by Antoine, I would prefer it to be applied to net-next
so that there is time for more people to test before it hits -rc or
stable backports.

The symptoms were that although PHYs would come up, the GMAC never
reported that the link was up, or in some cases it did report link
up but packets would not flow.  Various approaches were tried to
work around that, such as switching to in-band negotiation from
PHY mode, but ultimately the problem was in the way mvpp2 was being
programmed.

This series addresses that by, essentially, making mvpp2 follow the
same implementation pattern as mvneta: we configure the GMAC in three
stages:

1) the PHY interface mode
2) the negotiation advert
3) the negotiation style

Another issue is that mvpp2 was always taking the link down each time
its mac_config method was called: this is disruptive when the link is
already up, and we're just updating settings such as flow control.
There are some circumstances where we make the call despite there
being no changes (eg, when phylink is polling a GPIO or using a custom
link state function.)

This series depends on two previous patches already sent for net-next:
  net: marvell: mvpp2: fix lack of link interrupts
  net: marvell: mvpp2: use phy_interface_mode_is_8023z() helper

There is one last patch which deals with link status interrupts, which
I'll send separately because I think there's other considerations, but
that should not hold up this series of patches.
====================
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parents 8b34ec65 a4650477
......@@ -402,8 +402,8 @@
#define MVPP2_GMAC_STATUS0_GMII_SPEED BIT(1)
#define MVPP2_GMAC_STATUS0_MII_SPEED BIT(2)
#define MVPP2_GMAC_STATUS0_FULL_DUPLEX BIT(3)
#define MVPP2_GMAC_STATUS0_RX_PAUSE BIT(6)
#define MVPP2_GMAC_STATUS0_TX_PAUSE BIT(7)
#define MVPP2_GMAC_STATUS0_RX_PAUSE BIT(4)
#define MVPP2_GMAC_STATUS0_TX_PAUSE BIT(5)
#define MVPP2_GMAC_STATUS0_AN_COMPLETE BIT(11)
#define MVPP2_GMAC_PORT_FIFO_CFG_1_REG 0x1c
#define MVPP2_GMAC_TX_FIFO_MIN_TH_OFFS 6
......
......@@ -1377,13 +1377,9 @@ static void mvpp2_port_reset(struct mvpp2_port *port)
for (i = 0; i < ARRAY_SIZE(mvpp2_ethtool_regs); i++)
mvpp2_read_count(port, &mvpp2_ethtool_regs[i]);
val = readl(port->base + MVPP2_GMAC_CTRL_2_REG) &
~MVPP2_GMAC_PORT_RESET_MASK;
val = readl(port->base + MVPP2_GMAC_CTRL_2_REG) |
MVPP2_GMAC_PORT_RESET_MASK;
writel(val, port->base + MVPP2_GMAC_CTRL_2_REG);
while (readl(port->base + MVPP2_GMAC_CTRL_2_REG) &
MVPP2_GMAC_PORT_RESET_MASK)
continue;
}
/* Change maximum receive size of the port */
......@@ -4501,17 +4497,12 @@ static int mvpp2_phylink_mac_link_state(struct net_device *dev,
static void mvpp2_mac_an_restart(struct net_device *dev)
{
struct mvpp2_port *port = netdev_priv(dev);
u32 val;
u32 val = readl(port->base + MVPP2_GMAC_AUTONEG_CONFIG);
if (port->phy_interface != PHY_INTERFACE_MODE_SGMII)
return;
val = readl(port->base + MVPP2_GMAC_AUTONEG_CONFIG);
/* The RESTART_AN bit is cleared by the h/w after restarting the AN
* process.
*/
val |= MVPP2_GMAC_IN_BAND_RESTART_AN | MVPP2_GMAC_IN_BAND_AUTONEG;
writel(val, port->base + MVPP2_GMAC_AUTONEG_CONFIG);
writel(val | MVPP2_GMAC_IN_BAND_RESTART_AN,
port->base + MVPP2_GMAC_AUTONEG_CONFIG);
writel(val & ~MVPP2_GMAC_IN_BAND_RESTART_AN,
port->base + MVPP2_GMAC_AUTONEG_CONFIG);
}
static void mvpp2_xlg_config(struct mvpp2_port *port, unsigned int mode,
......@@ -4538,83 +4529,130 @@ static void mvpp2_xlg_config(struct mvpp2_port *port, unsigned int mode,
static void mvpp2_gmac_config(struct mvpp2_port *port, unsigned int mode,
const struct phylink_link_state *state)
{
u32 an, ctrl0, ctrl2, ctrl4;
u32 old_an, an;
u32 old_ctrl0, ctrl0;
u32 old_ctrl2, ctrl2;
u32 old_ctrl4, ctrl4;
an = readl(port->base + MVPP2_GMAC_AUTONEG_CONFIG);
ctrl0 = readl(port->base + MVPP2_GMAC_CTRL_0_REG);
ctrl2 = readl(port->base + MVPP2_GMAC_CTRL_2_REG);
ctrl4 = readl(port->base + MVPP22_GMAC_CTRL_4_REG);
/* Force link down */
an &= ~MVPP2_GMAC_FORCE_LINK_PASS;
an |= MVPP2_GMAC_FORCE_LINK_DOWN;
writel(an, port->base + MVPP2_GMAC_AUTONEG_CONFIG);
/* Set the GMAC in a reset state */
ctrl2 |= MVPP2_GMAC_PORT_RESET_MASK;
writel(ctrl2, port->base + MVPP2_GMAC_CTRL_2_REG);
old_an = an = readl(port->base + MVPP2_GMAC_AUTONEG_CONFIG);
old_ctrl0 = ctrl0 = readl(port->base + MVPP2_GMAC_CTRL_0_REG);
old_ctrl2 = ctrl2 = readl(port->base + MVPP2_GMAC_CTRL_2_REG);
old_ctrl4 = ctrl4 = readl(port->base + MVPP22_GMAC_CTRL_4_REG);
an &= ~(MVPP2_GMAC_CONFIG_MII_SPEED | MVPP2_GMAC_CONFIG_GMII_SPEED |
MVPP2_GMAC_AN_SPEED_EN | MVPP2_GMAC_FC_ADV_EN |
MVPP2_GMAC_FC_ADV_ASM_EN | MVPP2_GMAC_FLOW_CTRL_AUTONEG |
MVPP2_GMAC_CONFIG_FULL_DUPLEX | MVPP2_GMAC_AN_DUPLEX_EN |
MVPP2_GMAC_FORCE_LINK_DOWN);
MVPP2_GMAC_IN_BAND_AUTONEG | MVPP2_GMAC_IN_BAND_AUTONEG_BYPASS);
ctrl0 &= ~MVPP2_GMAC_PORT_TYPE_MASK;
ctrl2 &= ~(MVPP2_GMAC_PORT_RESET_MASK | MVPP2_GMAC_PCS_ENABLE_MASK);
ctrl2 &= ~(MVPP2_GMAC_INBAND_AN_MASK | MVPP2_GMAC_PORT_RESET_MASK |
MVPP2_GMAC_PCS_ENABLE_MASK);
ctrl4 &= ~(MVPP22_CTRL4_RX_FC_EN | MVPP22_CTRL4_TX_FC_EN);
/* Configure port type */
if (phy_interface_mode_is_8023z(state->interface)) {
/* 1000BaseX and 2500BaseX ports cannot negotiate speed nor can
* they negotiate duplex: they are always operating with a fixed
* speed of 1000/2500Mbps in full duplex, so force 1000/2500
* speed and full duplex here.
*/
ctrl0 |= MVPP2_GMAC_PORT_TYPE_MASK;
an |= MVPP2_GMAC_CONFIG_GMII_SPEED |
MVPP2_GMAC_CONFIG_FULL_DUPLEX;
} else if (!phy_interface_mode_is_rgmii(state->interface)) {
an |= MVPP2_GMAC_AN_SPEED_EN | MVPP2_GMAC_FLOW_CTRL_AUTONEG;
ctrl2 |= MVPP2_GMAC_PCS_ENABLE_MASK;
ctrl4 &= ~MVPP22_CTRL4_EXT_PIN_GMII_SEL;
ctrl4 |= MVPP22_CTRL4_SYNC_BYPASS_DIS |
MVPP22_CTRL4_DP_CLK_SEL |
MVPP22_CTRL4_QSGMII_BYPASS_ACTIVE;
} else if (state->interface == PHY_INTERFACE_MODE_SGMII) {
ctrl2 |= MVPP2_GMAC_PCS_ENABLE_MASK | MVPP2_GMAC_INBAND_AN_MASK;
ctrl4 &= ~MVPP22_CTRL4_EXT_PIN_GMII_SEL;
ctrl4 |= MVPP22_CTRL4_SYNC_BYPASS_DIS |
MVPP22_CTRL4_DP_CLK_SEL |
MVPP22_CTRL4_QSGMII_BYPASS_ACTIVE;
} else if (phy_interface_mode_is_rgmii(state->interface)) {
ctrl4 &= ~MVPP22_CTRL4_DP_CLK_SEL;
ctrl4 |= MVPP22_CTRL4_EXT_PIN_GMII_SEL |
MVPP22_CTRL4_SYNC_BYPASS_DIS |
MVPP22_CTRL4_QSGMII_BYPASS_ACTIVE;
}
if (state->duplex)
an |= MVPP2_GMAC_CONFIG_FULL_DUPLEX;
/* Configure advertisement bits */
if (phylink_test(state->advertising, Pause))
an |= MVPP2_GMAC_FC_ADV_EN;
if (phylink_test(state->advertising, Asym_Pause))
an |= MVPP2_GMAC_FC_ADV_ASM_EN;
if (phy_interface_mode_is_8023z(state->interface) ||
state->interface == PHY_INTERFACE_MODE_SGMII) {
an |= MVPP2_GMAC_IN_BAND_AUTONEG;
ctrl2 |= MVPP2_GMAC_INBAND_AN_MASK | MVPP2_GMAC_PCS_ENABLE_MASK;
/* Configure negotiation style */
if (!phylink_autoneg_inband(mode)) {
/* Phy or fixed speed - no in-band AN */
if (state->duplex)
an |= MVPP2_GMAC_CONFIG_FULL_DUPLEX;
ctrl4 &= ~(MVPP22_CTRL4_EXT_PIN_GMII_SEL |
MVPP22_CTRL4_RX_FC_EN | MVPP22_CTRL4_TX_FC_EN);
ctrl4 |= MVPP22_CTRL4_SYNC_BYPASS_DIS |
MVPP22_CTRL4_DP_CLK_SEL |
MVPP22_CTRL4_QSGMII_BYPASS_ACTIVE;
if (state->speed == SPEED_1000 || state->speed == SPEED_2500)
an |= MVPP2_GMAC_CONFIG_GMII_SPEED;
else if (state->speed == SPEED_100)
an |= MVPP2_GMAC_CONFIG_MII_SPEED;
if (state->pause & MLO_PAUSE_TX)
ctrl4 |= MVPP22_CTRL4_TX_FC_EN;
if (state->pause & MLO_PAUSE_RX)
ctrl4 |= MVPP22_CTRL4_RX_FC_EN;
} else if (phy_interface_mode_is_rgmii(state->interface)) {
an |= MVPP2_GMAC_IN_BAND_AUTONEG_BYPASS;
} else if (state->interface == PHY_INTERFACE_MODE_SGMII) {
/* SGMII in-band mode receives the speed and duplex from
* the PHY. Flow control information is not received. */
an &= ~(MVPP2_GMAC_FORCE_LINK_DOWN | MVPP2_GMAC_FORCE_LINK_PASS);
an |= MVPP2_GMAC_IN_BAND_AUTONEG |
MVPP2_GMAC_AN_SPEED_EN |
MVPP2_GMAC_AN_DUPLEX_EN;
if (state->speed == SPEED_1000)
an |= MVPP2_GMAC_CONFIG_GMII_SPEED;
else if (state->speed == SPEED_100)
an |= MVPP2_GMAC_CONFIG_MII_SPEED;
if (state->pause & MLO_PAUSE_TX)
ctrl4 |= MVPP22_CTRL4_TX_FC_EN;
if (state->pause & MLO_PAUSE_RX)
ctrl4 |= MVPP22_CTRL4_RX_FC_EN;
} else if (phy_interface_mode_is_8023z(state->interface)) {
/* 1000BaseX and 2500BaseX ports cannot negotiate speed nor can
* they negotiate duplex: they are always operating with a fixed
* speed of 1000/2500Mbps in full duplex, so force 1000/2500
* speed and full duplex here.
*/
ctrl0 |= MVPP2_GMAC_PORT_TYPE_MASK;
an &= ~(MVPP2_GMAC_FORCE_LINK_DOWN | MVPP2_GMAC_FORCE_LINK_PASS);
an |= MVPP2_GMAC_IN_BAND_AUTONEG |
MVPP2_GMAC_CONFIG_GMII_SPEED |
MVPP2_GMAC_CONFIG_FULL_DUPLEX;
ctrl4 &= ~MVPP22_CTRL4_DP_CLK_SEL;
ctrl4 |= MVPP22_CTRL4_EXT_PIN_GMII_SEL |
MVPP22_CTRL4_SYNC_BYPASS_DIS |
MVPP22_CTRL4_QSGMII_BYPASS_ACTIVE;
if (state->pause & MLO_PAUSE_AN && state->an_enabled) {
an |= MVPP2_GMAC_FLOW_CTRL_AUTONEG;
} else {
if (state->pause & MLO_PAUSE_TX)
ctrl4 |= MVPP22_CTRL4_TX_FC_EN;
if (state->pause & MLO_PAUSE_RX)
ctrl4 |= MVPP22_CTRL4_RX_FC_EN;
}
}
if ((old_ctrl0 ^ ctrl0) & MVPP2_GMAC_PORT_TYPE_MASK ||
(old_ctrl2 ^ ctrl2) & MVPP2_GMAC_INBAND_AN_MASK ||
(old_an ^ an) & MVPP2_GMAC_IN_BAND_AUTONEG) {
/* Force link down */
old_an &= ~MVPP2_GMAC_FORCE_LINK_PASS;
old_an |= MVPP2_GMAC_FORCE_LINK_DOWN;
writel(old_an, port->base + MVPP2_GMAC_AUTONEG_CONFIG);
/* Set the GMAC in a reset state - do this in a way that
* ensures we clear it below.
*/
old_ctrl2 |= MVPP2_GMAC_PORT_RESET_MASK;
writel(old_ctrl2, port->base + MVPP2_GMAC_CTRL_2_REG);
}
if (old_ctrl0 != ctrl0)
writel(ctrl0, port->base + MVPP2_GMAC_CTRL_0_REG);
if (old_ctrl2 != ctrl2)
writel(ctrl2, port->base + MVPP2_GMAC_CTRL_2_REG);
if (old_ctrl4 != ctrl4)
writel(ctrl4, port->base + MVPP22_GMAC_CTRL_4_REG);
if (old_an != an)
writel(an, port->base + MVPP2_GMAC_AUTONEG_CONFIG);
if (old_ctrl2 & MVPP2_GMAC_PORT_RESET_MASK) {
while (readl(port->base + MVPP2_GMAC_CTRL_2_REG) &
MVPP2_GMAC_PORT_RESET_MASK)
continue;
}
}
static void mvpp2_mac_config(struct net_device *dev, unsigned int mode,
......@@ -4670,7 +4708,6 @@ static void mvpp2_mac_link_up(struct net_device *dev, unsigned int mode,
interface != PHY_INTERFACE_MODE_10GKR) {
val = readl(port->base + MVPP2_GMAC_AUTONEG_CONFIG);
val &= ~MVPP2_GMAC_FORCE_LINK_DOWN;
if (phy_interface_mode_is_rgmii(interface))
val |= MVPP2_GMAC_FORCE_LINK_PASS;
writel(val, port->base + MVPP2_GMAC_AUTONEG_CONFIG);
}
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment