Merge tag 'tty-6.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty

Pull serial driver fixes from Greg KH:
 "Here are some small serial driver fixes for 6.7-rc4 to resolve some
  reported issues. Included in here are:

   - pl011 dma support fix

   - sc16is7xx driver fix

   - ma35d1 console index fix

   - 8250 driver fixes for small issues

  All of these have been in linux-next with no reported issues"

* tag 'tty-6.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  serial: 8250_dw: Add ACPI ID for Granite Rapids-D UART
  serial: ma35d1: Validate console index before assignment
  ARM: PL011: Fix DMA support
  serial: sc16is7xx: address RX timeout interrupt errata
  serial: 8250: 8250_omap: Clear UART_HAS_RHR_IT_DIS bit
  serial: 8250_omap: Add earlycon support for the AM654 UART controller
  serial: 8250: 8250_omap: Do not start RX DMA on THRI interrupt

drivers/tty/serial/8250/8250_dw.c

@@ -777,6 +777,7 @@ static const struct acpi_device_id dw8250_acpi_match[] = {
 	{ "INT33C5", (kernel_ulong_t)&dw8250_dw_apb },
 	{ "INT3434", (kernel_ulong_t)&dw8250_dw_apb },
 	{ "INT3435", (kernel_ulong_t)&dw8250_dw_apb },
+	{ "INTC10EE", (kernel_ulong_t)&dw8250_dw_apb },
 	{ },
 };
 MODULE_DEVICE_TABLE(acpi, dw8250_acpi_match);

drivers/tty/serial/8250/8250_early.c

@@ -189,5 +189,6 @@ static int __init early_omap8250_setup(struct earlycon_device *device,
 OF_EARLYCON_DECLARE(omap8250, "ti,omap2-uart", early_omap8250_setup);
 OF_EARLYCON_DECLARE(omap8250, "ti,omap3-uart", early_omap8250_setup);
 OF_EARLYCON_DECLARE(omap8250, "ti,omap4-uart", early_omap8250_setup);
+OF_EARLYCON_DECLARE(omap8250, "ti,am654-uart", early_omap8250_setup);
 
 #endif

drivers/tty/serial/8250/8250_omap.c

@@ -933,7 +933,7 @@ static void __dma_rx_do_complete(struct uart_8250_port *p)
 	if (priv->habit & UART_HAS_RHR_IT_DIS) {
 		reg = serial_in(p, UART_OMAP_IER2);
 		reg &= ~UART_OMAP_IER2_RHR_IT_DIS;
-		serial_out(p, UART_OMAP_IER2, UART_OMAP_IER2_RHR_IT_DIS);
+		serial_out(p, UART_OMAP_IER2, reg);
 	}
 
 	dmaengine_tx_status(rxchan, cookie, &state);
@@ -1079,7 +1079,7 @@ static int omap_8250_rx_dma(struct uart_8250_port *p)
 	if (priv->habit & UART_HAS_RHR_IT_DIS) {
 		reg = serial_in(p, UART_OMAP_IER2);
 		reg |= UART_OMAP_IER2_RHR_IT_DIS;
-		serial_out(p, UART_OMAP_IER2, UART_OMAP_IER2_RHR_IT_DIS);
+		serial_out(p, UART_OMAP_IER2, reg);
 	}
 
 	dma_async_issue_pending(dma->rxchan);
@@ -1298,10 +1298,12 @@ static int omap_8250_dma_handle_irq(struct uart_port *port)
 
 	status = serial_port_in(port, UART_LSR);
 
+	if ((iir & 0x3f) != UART_IIR_THRI) {
 		if (priv->habit & UART_HAS_EFR2)
 			am654_8250_handle_rx_dma(up, iir, status);
 		else
 			status = omap_8250_handle_rx_dma(up, iir, status);
+	}
 
 	serial8250_modem_status(up);
 	if (status & UART_LSR_THRE && up->dma->tx_err) {

drivers/tty/serial/amba-pl011.c

@@ -218,8 +218,9 @@ static struct vendor_data vendor_st = {
 
 /* Deals with DMA transactions */
 
-struct pl011_sgbuf {
-	struct scatterlist sg;
+struct pl011_dmabuf {
+	dma_addr_t		dma;
+	size_t			len;
 	char			*buf;
 };
 
@@ -227,8 +228,8 @@ struct pl011_dmarx_data {
 	struct dma_chan		*chan;
 	struct completion	complete;
 	bool			use_buf_b;
-	struct pl011_sgbuf	sgbuf_a;
-	struct pl011_sgbuf	sgbuf_b;
+	struct pl011_dmabuf	dbuf_a;
+	struct pl011_dmabuf	dbuf_b;
 	dma_cookie_t		cookie;
 	bool			running;
 	struct timer_list	timer;
@@ -241,7 +242,8 @@ struct pl011_dmarx_data {
 
 struct pl011_dmatx_data {
 	struct dma_chan		*chan;
-	struct scatterlist	sg;
+	dma_addr_t		dma;
+	size_t			len;
 	char			*buf;
 	bool			queued;
 };
@@ -366,32 +368,24 @@ static int pl011_fifo_to_tty(struct uart_amba_port *uap)
 
 #define PL011_DMA_BUFFER_SIZE PAGE_SIZE
 
-static int pl011_sgbuf_init(struct dma_chan *chan, struct pl011_sgbuf *sg,
+static int pl011_dmabuf_init(struct dma_chan *chan, struct pl011_dmabuf *db,
 	enum dma_data_direction dir)
 {
-	dma_addr_t dma_addr;
-
-	sg->buf = dma_alloc_coherent(chan->device->dev,
-		PL011_DMA_BUFFER_SIZE, &dma_addr, GFP_KERNEL);
-	if (!sg->buf)
+	db->buf = dma_alloc_coherent(chan->device->dev, PL011_DMA_BUFFER_SIZE,
+				     &db->dma, GFP_KERNEL);
+	if (!db->buf)
 		return -ENOMEM;
-
-	sg_init_table(&sg->sg, 1);
-	sg_set_page(&sg->sg, phys_to_page(dma_addr),
-		PL011_DMA_BUFFER_SIZE, offset_in_page(dma_addr));
-	sg_dma_address(&sg->sg) = dma_addr;
-	sg_dma_len(&sg->sg) = PL011_DMA_BUFFER_SIZE;
+	db->len = PL011_DMA_BUFFER_SIZE;
 
 	return 0;
 }
 
-static void pl011_sgbuf_free(struct dma_chan *chan, struct pl011_sgbuf *sg,
+static void pl011_dmabuf_free(struct dma_chan *chan, struct pl011_dmabuf *db,
 	enum dma_data_direction dir)
 {
-	if (sg->buf) {
+	if (db->buf) {
 		dma_free_coherent(chan->device->dev,
-			PL011_DMA_BUFFER_SIZE, sg->buf,
-			sg_dma_address(&sg->sg));
+				  PL011_DMA_BUFFER_SIZE, db->buf, db->dma);
 	}
 }
 
@@ -552,8 +546,8 @@ static void pl011_dma_tx_callback(void *data)
 
 	uart_port_lock_irqsave(&uap->port, &flags);
 	if (uap->dmatx.queued)
-		dma_unmap_sg(dmatx->chan->device->dev, &dmatx->sg, 1,
-			     DMA_TO_DEVICE);
+		dma_unmap_single(dmatx->chan->device->dev, dmatx->dma,
+				dmatx->len, DMA_TO_DEVICE);
 
 	dmacr = uap->dmacr;
 	uap->dmacr = dmacr & ~UART011_TXDMAE;
@@ -639,18 +633,19 @@ static int pl011_dma_tx_refill(struct uart_amba_port *uap)
 			memcpy(&dmatx->buf[first], &xmit->buf[0], second);
 	}
 
-	dmatx->sg.length = count;
-
-	if (dma_map_sg(dma_dev->dev, &dmatx->sg, 1, DMA_TO_DEVICE) != 1) {
+	dmatx->len = count;
+	dmatx->dma = dma_map_single(dma_dev->dev, dmatx->buf, count,
+				    DMA_TO_DEVICE);
+	if (dmatx->dma == DMA_MAPPING_ERROR) {
 		uap->dmatx.queued = false;
 		dev_dbg(uap->port.dev, "unable to map TX DMA\n");
 		return -EBUSY;
 	}
 
-	desc = dmaengine_prep_slave_sg(chan, &dmatx->sg, 1, DMA_MEM_TO_DEV,
+	desc = dmaengine_prep_slave_single(chan, dmatx->dma, dmatx->len, DMA_MEM_TO_DEV,
 					     DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
 	if (!desc) {
-		dma_unmap_sg(dma_dev->dev, &dmatx->sg, 1, DMA_TO_DEVICE);
+		dma_unmap_single(dma_dev->dev, dmatx->dma, dmatx->len, DMA_TO_DEVICE);
 		uap->dmatx.queued = false;
 		/*
 		 * If DMA cannot be used right now, we complete this
@@ -813,8 +808,8 @@ __acquires(&uap->port.lock)
 	dmaengine_terminate_async(uap->dmatx.chan);
 
 	if (uap->dmatx.queued) {
-		dma_unmap_sg(uap->dmatx.chan->device->dev, &uap->dmatx.sg, 1,
-			     DMA_TO_DEVICE);
+		dma_unmap_single(uap->dmatx.chan->device->dev, uap->dmatx.dma,
+				 uap->dmatx.len, DMA_TO_DEVICE);
 		uap->dmatx.queued = false;
 		uap->dmacr &= ~UART011_TXDMAE;
 		pl011_write(uap->dmacr, uap, REG_DMACR);
@@ -828,15 +823,15 @@ static int pl011_dma_rx_trigger_dma(struct uart_amba_port *uap)
 	struct dma_chan *rxchan = uap->dmarx.chan;
 	struct pl011_dmarx_data *dmarx = &uap->dmarx;
 	struct dma_async_tx_descriptor *desc;
-	struct pl011_sgbuf *sgbuf;
+	struct pl011_dmabuf *dbuf;
 
 	if (!rxchan)
 		return -EIO;
 
 	/* Start the RX DMA job */
-	sgbuf = uap->dmarx.use_buf_b ?
-		&uap->dmarx.sgbuf_b : &uap->dmarx.sgbuf_a;
-	desc = dmaengine_prep_slave_sg(rxchan, &sgbuf->sg, 1,
+	dbuf = uap->dmarx.use_buf_b ?
+		&uap->dmarx.dbuf_b : &uap->dmarx.dbuf_a;
+	desc = dmaengine_prep_slave_single(rxchan, dbuf->dma, dbuf->len,
 					DMA_DEV_TO_MEM,
 					DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
 	/*
@@ -876,8 +871,8 @@ static void pl011_dma_rx_chars(struct uart_amba_port *uap,
 			       bool readfifo)
 {
 	struct tty_port *port = &uap->port.state->port;
-	struct pl011_sgbuf *sgbuf = use_buf_b ?
-		&uap->dmarx.sgbuf_b : &uap->dmarx.sgbuf_a;
+	struct pl011_dmabuf *dbuf = use_buf_b ?
+		&uap->dmarx.dbuf_b : &uap->dmarx.dbuf_a;
 	int dma_count = 0;
 	u32 fifotaken = 0; /* only used for vdbg() */
 
@@ -886,7 +881,7 @@ static void pl011_dma_rx_chars(struct uart_amba_port *uap,
 
 	if (uap->dmarx.poll_rate) {
 		/* The data can be taken by polling */
-		dmataken = sgbuf->sg.length - dmarx->last_residue;
+		dmataken = dbuf->len - dmarx->last_residue;
 		/* Recalculate the pending size */
 		if (pending >= dmataken)
 			pending -= dmataken;
@@ -900,7 +895,7 @@ static void pl011_dma_rx_chars(struct uart_amba_port *uap,
 		 * Note that tty_insert_flip_buf() tries to take as many chars
 		 * as it can.
 		 */
-		dma_count = tty_insert_flip_string(port, sgbuf->buf + dmataken,
+		dma_count = tty_insert_flip_string(port, dbuf->buf + dmataken,
 				pending);
 
 		uap->port.icount.rx += dma_count;
@@ -911,7 +906,7 @@ static void pl011_dma_rx_chars(struct uart_amba_port *uap,
 
 	/* Reset the last_residue for Rx DMA poll */
 	if (uap->dmarx.poll_rate)
-		dmarx->last_residue = sgbuf->sg.length;
+		dmarx->last_residue = dbuf->len;
 
 	/*
 	 * Only continue with trying to read the FIFO if all DMA chars have
@@ -946,8 +941,8 @@ static void pl011_dma_rx_irq(struct uart_amba_port *uap)
 {
 	struct pl011_dmarx_data *dmarx = &uap->dmarx;
 	struct dma_chan *rxchan = dmarx->chan;
-	struct pl011_sgbuf *sgbuf = dmarx->use_buf_b ?
-		&dmarx->sgbuf_b : &dmarx->sgbuf_a;
+	struct pl011_dmabuf *dbuf = dmarx->use_buf_b ?
+		&dmarx->dbuf_b : &dmarx->dbuf_a;
 	size_t pending;
 	struct dma_tx_state state;
 	enum dma_status dmastat;
@@ -969,7 +964,7 @@ static void pl011_dma_rx_irq(struct uart_amba_port *uap)
 	pl011_write(uap->dmacr, uap, REG_DMACR);
 	uap->dmarx.running = false;
 
-	pending = sgbuf->sg.length - state.residue;
+	pending = dbuf->len - state.residue;
 	BUG_ON(pending > PL011_DMA_BUFFER_SIZE);
 	/* Then we terminate the transfer - we now know our residue */
 	dmaengine_terminate_all(rxchan);
@@ -996,8 +991,8 @@ static void pl011_dma_rx_callback(void *data)
 	struct pl011_dmarx_data *dmarx = &uap->dmarx;
 	struct dma_chan *rxchan = dmarx->chan;
 	bool lastbuf = dmarx->use_buf_b;
-	struct pl011_sgbuf *sgbuf = dmarx->use_buf_b ?
-		&dmarx->sgbuf_b : &dmarx->sgbuf_a;
+	struct pl011_dmabuf *dbuf = dmarx->use_buf_b ?
+		&dmarx->dbuf_b : &dmarx->dbuf_a;
 	size_t pending;
 	struct dma_tx_state state;
 	int ret;
@@ -1015,7 +1010,7 @@ static void pl011_dma_rx_callback(void *data)
 	 * the DMA irq handler. So we check the residue here.
 	 */
 	rxchan->device->device_tx_status(rxchan, dmarx->cookie, &state);
-	pending = sgbuf->sg.length - state.residue;
+	pending = dbuf->len - state.residue;
 	BUG_ON(pending > PL011_DMA_BUFFER_SIZE);
 	/* Then we terminate the transfer - we now know our residue */
 	dmaengine_terminate_all(rxchan);
@@ -1067,16 +1062,16 @@ static void pl011_dma_rx_poll(struct timer_list *t)
 	unsigned long flags;
 	unsigned int dmataken = 0;
 	unsigned int size = 0;
-	struct pl011_sgbuf *sgbuf;
+	struct pl011_dmabuf *dbuf;
 	int dma_count;
 	struct dma_tx_state state;
 
-	sgbuf = dmarx->use_buf_b ? &uap->dmarx.sgbuf_b : &uap->dmarx.sgbuf_a;
+	dbuf = dmarx->use_buf_b ? &uap->dmarx.dbuf_b : &uap->dmarx.dbuf_a;
 	rxchan->device->device_tx_status(rxchan, dmarx->cookie, &state);
 	if (likely(state.residue < dmarx->last_residue)) {
-		dmataken = sgbuf->sg.length - dmarx->last_residue;
+		dmataken = dbuf->len - dmarx->last_residue;
 		size = dmarx->last_residue - state.residue;
-		dma_count = tty_insert_flip_string(port, sgbuf->buf + dmataken,
+		dma_count = tty_insert_flip_string(port, dbuf->buf + dmataken,
 				size);
 		if (dma_count == size)
 			dmarx->last_residue =  state.residue;
@@ -1123,7 +1118,7 @@ static void pl011_dma_startup(struct uart_amba_port *uap)
 		return;
 	}
 
-	sg_init_one(&uap->dmatx.sg, uap->dmatx.buf, PL011_DMA_BUFFER_SIZE);
+	uap->dmatx.len = PL011_DMA_BUFFER_SIZE;
 
 	/* The DMA buffer is now the FIFO the TTY subsystem can use */
 	uap->port.fifosize = PL011_DMA_BUFFER_SIZE;
@@ -1133,7 +1128,7 @@ static void pl011_dma_startup(struct uart_amba_port *uap)
 		goto skip_rx;
 
 	/* Allocate and map DMA RX buffers */
-	ret = pl011_sgbuf_init(uap->dmarx.chan, &uap->dmarx.sgbuf_a,
+	ret = pl011_dmabuf_init(uap->dmarx.chan, &uap->dmarx.dbuf_a,
 			       DMA_FROM_DEVICE);
 	if (ret) {
 		dev_err(uap->port.dev, "failed to init DMA %s: %d\n",
@@ -1141,12 +1136,12 @@ static void pl011_dma_startup(struct uart_amba_port *uap)
 		goto skip_rx;
 	}
 
-	ret = pl011_sgbuf_init(uap->dmarx.chan, &uap->dmarx.sgbuf_b,
+	ret = pl011_dmabuf_init(uap->dmarx.chan, &uap->dmarx.dbuf_b,
 			       DMA_FROM_DEVICE);
 	if (ret) {
 		dev_err(uap->port.dev, "failed to init DMA %s: %d\n",
 			"RX buffer B", ret);
-		pl011_sgbuf_free(uap->dmarx.chan, &uap->dmarx.sgbuf_a,
+		pl011_dmabuf_free(uap->dmarx.chan, &uap->dmarx.dbuf_a,
 				 DMA_FROM_DEVICE);
 		goto skip_rx;
 	}
@@ -1200,7 +1195,8 @@ static void pl011_dma_shutdown(struct uart_amba_port *uap)
 		/* In theory, this should already be done by pl011_dma_flush_buffer */
 		dmaengine_terminate_all(uap->dmatx.chan);
 		if (uap->dmatx.queued) {
-			dma_unmap_sg(uap->dmatx.chan->device->dev, &uap->dmatx.sg, 1,
+			dma_unmap_single(uap->dmatx.chan->device->dev,
+					 uap->dmatx.dma, uap->dmatx.len,
 					 DMA_TO_DEVICE);
 			uap->dmatx.queued = false;
 		}
@@ -1212,8 +1208,8 @@ static void pl011_dma_shutdown(struct uart_amba_port *uap)
 	if (uap->using_rx_dma) {
 		dmaengine_terminate_all(uap->dmarx.chan);
 		/* Clean up the RX DMA */
-		pl011_sgbuf_free(uap->dmarx.chan, &uap->dmarx.sgbuf_a, DMA_FROM_DEVICE);
-		pl011_sgbuf_free(uap->dmarx.chan, &uap->dmarx.sgbuf_b, DMA_FROM_DEVICE);
+		pl011_dmabuf_free(uap->dmarx.chan, &uap->dmarx.dbuf_a, DMA_FROM_DEVICE);
+		pl011_dmabuf_free(uap->dmarx.chan, &uap->dmarx.dbuf_b, DMA_FROM_DEVICE);
 		if (uap->dmarx.poll_rate)
 			del_timer_sync(&uap->dmarx.timer);
 		uap->using_rx_dma = false;

drivers/tty/serial/ma35d1_serial.c

@@ -552,11 +552,19 @@ static void ma35d1serial_console_putchar(struct uart_port *port, unsigned char c
  */
 static void ma35d1serial_console_write(struct console *co, const char *s, u32 count)
 {
-	struct uart_ma35d1_port *up = &ma35d1serial_ports[co->index];
+	struct uart_ma35d1_port *up;
 	unsigned long flags;
 	int locked = 1;
 	u32 ier;
 
+	if ((co->index < 0) || (co->index >= MA35_UART_NR)) {
+		pr_warn("Failed to write on ononsole port %x, out of range\n",
+			co->index);
+		return;
+	}
+
+	up = &ma35d1serial_ports[co->index];
+
 	if (up->port.sysrq)
 		locked = 0;
 	else if (oops_in_progress)

drivers/tty/serial/sc16is7xx.c

@@ -766,6 +766,18 @@ static bool sc16is7xx_port_irq(struct sc16is7xx_port *s, int portno)
 		case SC16IS7XX_IIR_RTOI_SRC:
 		case SC16IS7XX_IIR_XOFFI_SRC:
 			rxlen = sc16is7xx_port_read(port, SC16IS7XX_RXLVL_REG);
+
+			/*
+			 * There is a silicon bug that makes the chip report a
+			 * time-out interrupt but no data in the FIFO. This is
+			 * described in errata section 18.1.4.
+			 *
+			 * When this happens, read one byte from the FIFO to
+			 * clear the interrupt.
+			 */
+			if (iir == SC16IS7XX_IIR_RTOI_SRC && !rxlen)
+				rxlen = 1;
+
 			if (rxlen)
 				sc16is7xx_handle_rx(port, rxlen, iir);
 			break;