Merge branch 'net-dsa-mt7530-PHYLINK-and-port-5'

René van Dorst says:

====================
net: dsa: mt7530: Convert to PHYLINK and add support for port 5

1. net: dsa: mt7530: Convert to PHYLINK API
   This patch converts mt7530 to PHYLINK API.
2. dt-bindings: net: dsa: mt7530: Add support for port 5
3. net: dsa: mt7530: Add support for port 5
   These 2 patches adding support for port 5 of the switch.

v2->v3:
 * Removed 'status = "okay"' lines in patch #2
 * Change a port 5 setup message in a debug message in patch #3
 * Added ack-by and tested-by tags
v1->v2:
 * Mostly phylink improvements after review.
rfc -> v1:
 * Mostly phylink improvements after review.
 * Drop phy isolation patches. Adds no value for now.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Documentation/devicetree/bindings/net/dsa/mt7530.txt

@@ -35,6 +35,42 @@ Required properties for the child nodes within ports container:
 - phy-mode: String, must be either "trgmii" or "rgmii" for port labeled
 	 "cpu".
 
+Port 5 of the switch is muxed between:
+1. GMAC5: GMAC5 can interface with another external MAC or PHY.
+2. PHY of port 0 or port 4: PHY interfaces with an external MAC like 2nd GMAC
+   of the SOC. Used in many setups where port 0/4 becomes the WAN port.
+   Note: On a MT7621 SOC with integrated switch: 2nd GMAC can only connected to
+	 GMAC5 when the gpios for RGMII2 (GPIO 22-33) are not used and not
+	 connected to external component!
+
+Port 5 modes/configurations:
+1. Port 5 is disabled and isolated: An external phy can interface to the 2nd
+   GMAC of the SOC.
+   In the case of a build-in MT7530 switch, port 5 shares the RGMII bus with 2nd
+   GMAC and an optional external phy. Mind the GPIO/pinctl settings of the SOC!
+2. Port 5 is muxed to PHY of port 0/4: Port 0/4 interfaces with 2nd GMAC.
+   It is a simple MAC to PHY interface, port 5 needs to be setup for xMII mode
+   and RGMII delay.
+3. Port 5 is muxed to GMAC5 and can interface to an external phy.
+   Port 5 becomes an extra switch port.
+   Only works on platform where external phy TX<->RX lines are swapped.
+   Like in the Ubiquiti ER-X-SFP.
+4. Port 5 is muxed to GMAC5 and interfaces with the 2nd GAMC as 2nd CPU port.
+   Currently a 2nd CPU port is not supported by DSA code.
+
+Depending on how the external PHY is wired:
+1. normal: The PHY can only connect to 2nd GMAC but not to the switch
+2. swapped: RGMII TX, RX are swapped; external phy interface with the switch as
+   a ethernet port. But can't interface to the 2nd GMAC.
+
+Based on the DT the port 5 mode is configured.
+
+Driver tries to lookup the phy-handle of the 2nd GMAC of the master device.
+When phy-handle matches PHY of port 0 or 4 then port 5 set-up as mode 2.
+phy-mode must be set, see also example 2 below!
+ * mt7621: phy-mode = "rgmii-txid";
+ * mt7623: phy-mode = "rgmii";
+
 See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of additional
 required, optional properties and how the integrated switch subnodes must
 be specified.
@@ -94,3 +130,181 @@ Example:
 			};
 		};
 	};
+
+Example 2: MT7621: Port 4 is WAN port: 2nd GMAC -> Port 5 -> PHY port 4.
+
+&eth {
+	gmac0: mac@0 {
+		compatible = "mediatek,eth-mac";
+		reg = <0>;
+		phy-mode = "rgmii";
+
+		fixed-link {
+			speed = <1000>;
+			full-duplex;
+			pause;
+		};
+	};
+
+	gmac1: mac@1 {
+		compatible = "mediatek,eth-mac";
+		reg = <1>;
+		phy-mode = "rgmii-txid";
+		phy-handle = <&phy4>;
+	};
+
+	mdio: mdio-bus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Internal phy */
+		phy4: ethernet-phy@4 {
+			reg = <4>;
+		};
+
+		mt7530: switch@1f {
+			compatible = "mediatek,mt7621";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x1f>;
+			pinctrl-names = "default";
+			mediatek,mcm;
+
+			resets = <&rstctrl 2>;
+			reset-names = "mcm";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					label = "lan0";
+				};
+
+				port@1 {
+					reg = <1>;
+					label = "lan1";
+				};
+
+				port@2 {
+					reg = <2>;
+					label = "lan2";
+				};
+
+				port@3 {
+					reg = <3>;
+					label = "lan3";
+				};
+
+/* Commented out. Port 4 is handled by 2nd GMAC.
+				port@4 {
+					reg = <4>;
+					label = "lan4";
+				};
+*/
+
+				cpu_port0: port@6 {
+					reg = <6>;
+					label = "cpu";
+					ethernet = <&gmac0>;
+					phy-mode = "rgmii";
+
+					fixed-link {
+						speed = <1000>;
+						full-duplex;
+						pause;
+					};
+				};
+			};
+		};
+	};
+};
+
+Example 3: MT7621: Port 5 is connected to external PHY: Port 5 -> external PHY.
+
+&eth {
+	gmac0: mac@0 {
+		compatible = "mediatek,eth-mac";
+		reg = <0>;
+		phy-mode = "rgmii";
+
+		fixed-link {
+			speed = <1000>;
+			full-duplex;
+			pause;
+		};
+	};
+
+	mdio: mdio-bus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* External phy */
+		ephy5: ethernet-phy@7 {
+			reg = <7>;
+		};
+
+		mt7530: switch@1f {
+			compatible = "mediatek,mt7621";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x1f>;
+			pinctrl-names = "default";
+			mediatek,mcm;
+
+			resets = <&rstctrl 2>;
+			reset-names = "mcm";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					label = "lan0";
+				};
+
+				port@1 {
+					reg = <1>;
+					label = "lan1";
+				};
+
+				port@2 {
+					reg = <2>;
+					label = "lan2";
+				};
+
+				port@3 {
+					reg = <3>;
+					label = "lan3";
+				};
+
+				port@4 {
+					reg = <4>;
+					label = "lan4";
+				};
+
+				port@5 {
+					reg = <5>;
+					label = "lan5";
+					phy-mode = "rgmii";
+					phy-handle = <&ephy5>;
+				};
+
+				cpu_port0: port@6 {
+					reg = <6>;
+					label = "cpu";
+					ethernet = <&gmac0>;
+					phy-mode = "rgmii";
+
+					fixed-link {
+						speed = <1000>;
+						full-duplex;
+						pause;
+					};
+				};
+			};
+		};
+	};
+};

drivers/net/dsa/mt7530.c

@@ -13,7 +13,7 @@
 #include <linux/of_mdio.h>
 #include <linux/of_net.h>
 #include <linux/of_platform.h>
-#include <linux/phy.h>
+#include <linux/phylink.h>
 #include <linux/regmap.h>
 #include <linux/regulator/consumer.h>
 #include <linux/reset.h>
@@ -633,61 +633,75 @@ mt7530_get_sset_count(struct dsa_switch *ds, int port, int sset)
 	return ARRAY_SIZE(mt7530_mib);
 }
 
-static void mt7530_adjust_link(struct dsa_switch *ds, int port,
-			       struct phy_device *phydev)
+static void mt7530_setup_port5(struct dsa_switch *ds, phy_interface_t interface)
 {
 	struct mt7530_priv *priv = ds->priv;
+	u8 tx_delay = 0;
+	int val;
 
-	if (phy_is_pseudo_fixed_link(phydev)) {
-		dev_dbg(priv->dev, "phy-mode for master device = %x\n",
-			phydev->interface);
+	mutex_lock(&priv->reg_mutex);
 
-		/* Setup TX circuit incluing relevant PAD and driving */
-		mt7530_pad_clk_setup(ds, phydev->interface);
+	val = mt7530_read(priv, MT7530_MHWTRAP);
 
-		if (priv->id == ID_MT7530) {
-			/* Setup RX circuit, relevant PAD and driving on the
-			 * host which must be placed after the setup on the
-			 * device side is all finished.
-			 */
-			mt7623_pad_clk_setup(ds);
-		}
-	} else {
-		u16 lcl_adv = 0, rmt_adv = 0;
-		u8 flowctrl;
-		u32 mcr = PMCR_USERP_LINK | PMCR_FORCE_MODE;
+	val |= MHWTRAP_MANUAL | MHWTRAP_P5_MAC_SEL | MHWTRAP_P5_DIS;
+	val &= ~MHWTRAP_P5_RGMII_MODE & ~MHWTRAP_PHY0_SEL;
 
-		switch (phydev->speed) {
-		case SPEED_1000:
-			mcr |= PMCR_FORCE_SPEED_1000;
-			break;
-		case SPEED_100:
-			mcr |= PMCR_FORCE_SPEED_100;
-			break;
-		}
+	switch (priv->p5_intf_sel) {
+	case P5_INTF_SEL_PHY_P0:
+		/* MT7530_P5_MODE_GPHY_P0: 2nd GMAC -> P5 -> P0 */
+		val |= MHWTRAP_PHY0_SEL;
+		/* fall through */
+	case P5_INTF_SEL_PHY_P4:
+		/* MT7530_P5_MODE_GPHY_P4: 2nd GMAC -> P5 -> P4 */
+		val &= ~MHWTRAP_P5_MAC_SEL & ~MHWTRAP_P5_DIS;
+
+		/* Setup the MAC by default for the cpu port */
+		mt7530_write(priv, MT7530_PMCR_P(5), 0x56300);
+		break;
+	case P5_INTF_SEL_GMAC5:
+		/* MT7530_P5_MODE_GMAC: P5 -> External phy or 2nd GMAC */
+		val &= ~MHWTRAP_P5_DIS;
+		break;
+	case P5_DISABLED:
+		interface = PHY_INTERFACE_MODE_NA;
+		break;
+	default:
+		dev_err(ds->dev, "Unsupported p5_intf_sel %d\n",
+			priv->p5_intf_sel);
+		goto unlock_exit;
+	}
 
-		if (phydev->link)
-			mcr |= PMCR_FORCE_LNK;
+	/* Setup RGMII settings */
+	if (phy_interface_mode_is_rgmii(interface)) {
+		val |= MHWTRAP_P5_RGMII_MODE;
 
-		if (phydev->duplex) {
-			mcr |= PMCR_FORCE_FDX;
+		/* P5 RGMII RX Clock Control: delay setting for 1000M */
+		mt7530_write(priv, MT7530_P5RGMIIRXCR, CSR_RGMII_EDGE_ALIGN);
 
-			if (phydev->pause)
-				rmt_adv = LPA_PAUSE_CAP;
-			if (phydev->asym_pause)
-				rmt_adv |= LPA_PAUSE_ASYM;
+		/* Don't set delay in DSA mode */
+		if (!dsa_is_dsa_port(priv->ds, 5) &&
+		    (interface == PHY_INTERFACE_MODE_RGMII_TXID ||
+		     interface == PHY_INTERFACE_MODE_RGMII_ID))
+			tx_delay = 4; /* n * 0.5 ns */
 
-			lcl_adv = linkmode_adv_to_lcl_adv_t(
-				phydev->advertising);
-			flowctrl = mii_resolve_flowctrl_fdx(lcl_adv, rmt_adv);
+		/* P5 RGMII TX Clock Control: delay x */
+		mt7530_write(priv, MT7530_P5RGMIITXCR,
+			     CSR_RGMII_TXC_CFG(0x10 + tx_delay));
 
-			if (flowctrl & FLOW_CTRL_TX)
-				mcr |= PMCR_TX_FC_EN;
-			if (flowctrl & FLOW_CTRL_RX)
-				mcr |= PMCR_RX_FC_EN;
-		}
-		mt7530_write(priv, MT7530_PMCR_P(port), mcr);
+		/* reduce P5 RGMII Tx driving, 8mA */
+		mt7530_write(priv, MT7530_IO_DRV_CR,
+			     P5_IO_CLK_DRV(1) | P5_IO_DATA_DRV(1));
 	}
+
+	mt7530_write(priv, MT7530_MHWTRAP, val);
+
+	dev_dbg(ds->dev, "Setup P5, HWTRAP=0x%x, intf_sel=%s, phy-mode=%s\n",
+		val, p5_intf_modes(priv->p5_intf_sel), phy_modes(interface));
+
+	priv->p5_interface = interface;
+
+unlock_exit:
+	mutex_unlock(&priv->reg_mutex);
 }
 
 static int
@@ -698,9 +712,6 @@ mt7530_cpu_port_enable(struct mt7530_priv *priv,
 	mt7530_write(priv, MT7530_PVC_P(port),
 		     PORT_SPEC_TAG);
 
-	/* Setup the MAC by default for the cpu port */
-	mt7530_write(priv, MT7530_PMCR_P(port), PMCR_CPUP_LINK);
-
 	/* Disable auto learning on the cpu port */
 	mt7530_set(priv, MT7530_PSC_P(port), SA_DIS);
 
@@ -731,9 +742,6 @@ mt7530_port_enable(struct dsa_switch *ds, int port,
 
 	mutex_lock(&priv->reg_mutex);
 
-	/* Setup the MAC for the user port */
-	mt7530_write(priv, MT7530_PMCR_P(port), PMCR_USERP_LINK);
-
 	/* Allow the user port gets connected to the cpu port and also
 	 * restore the port matrix if the port is the member of a certain
 	 * bridge.
@@ -742,7 +750,7 @@ mt7530_port_enable(struct dsa_switch *ds, int port,
 	priv->ports[port].enable = true;
 	mt7530_rmw(priv, MT7530_PCR_P(port), PCR_MATRIX_MASK,
 		   priv->ports[port].pm);
-	mt7530_port_set_status(priv, port, 1);
+	mt7530_port_set_status(priv, port, 0);
 
 	mutex_unlock(&priv->reg_mutex);
 
@@ -1232,10 +1240,13 @@ static int
 mt7530_setup(struct dsa_switch *ds)
 {
 	struct mt7530_priv *priv = ds->priv;
-	int ret, i;
-	u32 id, val;
-	struct device_node *dn;
+	struct device_node *phy_node;
+	struct device_node *mac_np;
 	struct mt7530_dummy_poll p;
+	phy_interface_t interface;
+	struct device_node *dn;
+	u32 id, val;
+	int ret, i;
 
 	/* The parent node of master netdev which holds the common system
 	 * controller also is the container for two GMACs nodes representing
@@ -1305,6 +1316,8 @@ mt7530_setup(struct dsa_switch *ds)
 	val |= MHWTRAP_MANUAL;
 	mt7530_write(priv, MT7530_MHWTRAP, val);
 
+	priv->p6_interface = PHY_INTERFACE_MODE_NA;
+
 	/* Enable and reset MIB counters */
 	mt7530_mib_reset(ds);
 
@@ -1321,6 +1334,40 @@ mt7530_setup(struct dsa_switch *ds)
 			mt7530_port_disable(ds, i);
 	}
 
+	/* Setup port 5 */
+	priv->p5_intf_sel = P5_DISABLED;
+	interface = PHY_INTERFACE_MODE_NA;
+
+	if (!dsa_is_unused_port(ds, 5)) {
+		priv->p5_intf_sel = P5_INTF_SEL_GMAC5;
+		interface = of_get_phy_mode(ds->ports[5].dn);
+	} else {
+		/* Scan the ethernet nodes. look for GMAC1, lookup used phy */
+		for_each_child_of_node(dn, mac_np) {
+			if (!of_device_is_compatible(mac_np,
+						     "mediatek,eth-mac"))
+				continue;
+
+			ret = of_property_read_u32(mac_np, "reg", &id);
+			if (ret < 0 || id != 1)
+				continue;
+
+			phy_node = of_parse_phandle(mac_np, "phy-handle", 0);
+			if (phy_node->parent == priv->dev->of_node->parent) {
+				interface = of_get_phy_mode(mac_np);
+				id = of_mdio_parse_addr(ds->dev, phy_node);
+				if (id == 0)
+					priv->p5_intf_sel = P5_INTF_SEL_PHY_P0;
+				if (id == 4)
+					priv->p5_intf_sel = P5_INTF_SEL_PHY_P4;
+			}
+			of_node_put(phy_node);
+			break;
+		}
+	}
+
+	mt7530_setup_port5(ds, interface);
+
 	/* Flush the FDB table */
 	ret = mt7530_fdb_cmd(priv, MT7530_FDB_FLUSH, NULL);
 	if (ret < 0)
@@ -1329,6 +1376,216 @@ mt7530_setup(struct dsa_switch *ds)
 	return 0;
 }
 
+static void mt7530_phylink_mac_config(struct dsa_switch *ds, int port,
+				      unsigned int mode,
+				      const struct phylink_link_state *state)
+{
+	struct mt7530_priv *priv = ds->priv;
+	u32 mcr_cur, mcr_new;
+
+	switch (port) {
+	case 0: /* Internal phy */
+	case 1:
+	case 2:
+	case 3:
+	case 4:
+		if (state->interface != PHY_INTERFACE_MODE_GMII)
+			return;
+		break;
+	case 5: /* 2nd cpu port with phy of port 0 or 4 / external phy */
+		if (priv->p5_interface == state->interface)
+			break;
+		if (!phy_interface_mode_is_rgmii(state->interface) &&
+		    state->interface != PHY_INTERFACE_MODE_MII &&
+		    state->interface != PHY_INTERFACE_MODE_GMII)
+			return;
+
+		mt7530_setup_port5(ds, state->interface);
+		break;
+	case 6: /* 1st cpu port */
+		if (priv->p6_interface == state->interface)
+			break;
+
+		if (state->interface != PHY_INTERFACE_MODE_RGMII &&
+		    state->interface != PHY_INTERFACE_MODE_TRGMII)
+			return;
+
+		/* Setup TX circuit incluing relevant PAD and driving */
+		mt7530_pad_clk_setup(ds, state->interface);
+
+		if (priv->id == ID_MT7530) {
+			/* Setup RX circuit, relevant PAD and driving on the
+			 * host which must be placed after the setup on the
+			 * device side is all finished.
+			 */
+			mt7623_pad_clk_setup(ds);
+		}
+
+		priv->p6_interface = state->interface;
+		break;
+	default:
+		dev_err(ds->dev, "%s: unsupported port: %i\n", __func__, port);
+		return;
+	}
+
+	if (phylink_autoneg_inband(mode)) {
+		dev_err(ds->dev, "%s: in-band negotiation unsupported\n",
+			__func__);
+		return;
+	}
+
+	mcr_cur = mt7530_read(priv, MT7530_PMCR_P(port));
+	mcr_new = mcr_cur;
+	mcr_new &= ~(PMCR_FORCE_SPEED_1000 | PMCR_FORCE_SPEED_100 |
+		     PMCR_FORCE_FDX | PMCR_TX_FC_EN | PMCR_RX_FC_EN);
+	mcr_new |= PMCR_IFG_XMIT(1) | PMCR_MAC_MODE | PMCR_BACKOFF_EN |
+		   PMCR_BACKPR_EN | PMCR_FORCE_MODE | PMCR_FORCE_LNK;
+
+	/* Are we connected to external phy */
+	if (port == 5 && dsa_is_user_port(ds, 5))
+		mcr_new |= PMCR_EXT_PHY;
+
+	switch (state->speed) {
+	case SPEED_1000:
+		mcr_new |= PMCR_FORCE_SPEED_1000;
+		break;
+	case SPEED_100:
+		mcr_new |= PMCR_FORCE_SPEED_100;
+		break;
+	}
+	if (state->duplex == DUPLEX_FULL) {
+		mcr_new |= PMCR_FORCE_FDX;
+		if (state->pause & MLO_PAUSE_TX)
+			mcr_new |= PMCR_TX_FC_EN;
+		if (state->pause & MLO_PAUSE_RX)
+			mcr_new |= PMCR_RX_FC_EN;
+	}
+
+	if (mcr_new != mcr_cur)
+		mt7530_write(priv, MT7530_PMCR_P(port), mcr_new);
+}
+
+static void mt7530_phylink_mac_link_down(struct dsa_switch *ds, int port,
+					 unsigned int mode,
+					 phy_interface_t interface)
+{
+	struct mt7530_priv *priv = ds->priv;
+
+	mt7530_port_set_status(priv, port, 0);
+}
+
+static void mt7530_phylink_mac_link_up(struct dsa_switch *ds, int port,
+				       unsigned int mode,
+				       phy_interface_t interface,
+				       struct phy_device *phydev)
+{
+	struct mt7530_priv *priv = ds->priv;
+
+	mt7530_port_set_status(priv, port, 1);
+}
+
+static void mt7530_phylink_validate(struct dsa_switch *ds, int port,
+				    unsigned long *supported,
+				    struct phylink_link_state *state)
+{
+	__ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = { 0, };
+
+	switch (port) {
+	case 0: /* Internal phy */
+	case 1:
+	case 2:
+	case 3:
+	case 4:
+		if (state->interface != PHY_INTERFACE_MODE_NA &&
+		    state->interface != PHY_INTERFACE_MODE_GMII)
+			goto unsupported;
+		break;
+	case 5: /* 2nd cpu port with phy of port 0 or 4 / external phy */
+		if (state->interface != PHY_INTERFACE_MODE_NA &&
+		    !phy_interface_mode_is_rgmii(state->interface) &&
+		    state->interface != PHY_INTERFACE_MODE_MII &&
+		    state->interface != PHY_INTERFACE_MODE_GMII)
+			goto unsupported;
+		break;
+	case 6: /* 1st cpu port */
+		if (state->interface != PHY_INTERFACE_MODE_NA &&
+		    state->interface != PHY_INTERFACE_MODE_RGMII &&
+		    state->interface != PHY_INTERFACE_MODE_TRGMII)
+			goto unsupported;
+		break;
+	default:
+		dev_err(ds->dev, "%s: unsupported port: %i\n", __func__, port);
+unsupported:
+		linkmode_zero(supported);
+		return;
+	}
+
+	phylink_set_port_modes(mask);
+	phylink_set(mask, Autoneg);
+
+	if (state->interface == PHY_INTERFACE_MODE_TRGMII) {
+		phylink_set(mask, 1000baseT_Full);
+	} else {
+		phylink_set(mask, 10baseT_Half);
+		phylink_set(mask, 10baseT_Full);
+		phylink_set(mask, 100baseT_Half);
+		phylink_set(mask, 100baseT_Full);
+
+		if (state->interface != PHY_INTERFACE_MODE_MII) {
+			phylink_set(mask, 1000baseT_Half);
+			phylink_set(mask, 1000baseT_Full);
+			if (port == 5)
+				phylink_set(mask, 1000baseX_Full);
+		}
+	}
+
+	phylink_set(mask, Pause);
+	phylink_set(mask, Asym_Pause);
+
+	linkmode_and(supported, supported, mask);
+	linkmode_and(state->advertising, state->advertising, mask);
+}
+
+static int
+mt7530_phylink_mac_link_state(struct dsa_switch *ds, int port,
+			      struct phylink_link_state *state)
+{
+	struct mt7530_priv *priv = ds->priv;
+	u32 pmsr;
+
+	if (port < 0 || port >= MT7530_NUM_PORTS)
+		return -EINVAL;
+
+	pmsr = mt7530_read(priv, MT7530_PMSR_P(port));
+
+	state->link = (pmsr & PMSR_LINK);
+	state->an_complete = state->link;
+	state->duplex = !!(pmsr & PMSR_DPX);
+
+	switch (pmsr & PMSR_SPEED_MASK) {
+	case PMSR_SPEED_10:
+		state->speed = SPEED_10;
+		break;
+	case PMSR_SPEED_100:
+		state->speed = SPEED_100;
+		break;
+	case PMSR_SPEED_1000:
+		state->speed = SPEED_1000;
+		break;
+	default:
+		state->speed = SPEED_UNKNOWN;
+		break;
+	}
+
+	state->pause &= ~(MLO_PAUSE_RX | MLO_PAUSE_TX);
+	if (pmsr & PMSR_RX_FC)
+		state->pause |= MLO_PAUSE_RX;
+	if (pmsr & PMSR_TX_FC)
+		state->pause |= MLO_PAUSE_TX;
+
+	return 1;
+}
+
 static const struct dsa_switch_ops mt7530_switch_ops = {
 	.get_tag_protocol	= mtk_get_tag_protocol,
 	.setup			= mt7530_setup,
@@ -1337,7 +1594,6 @@ static const struct dsa_switch_ops mt7530_switch_ops = {
 	.phy_write		= mt7530_phy_write,
 	.get_ethtool_stats	= mt7530_get_ethtool_stats,
 	.get_sset_count		= mt7530_get_sset_count,
-	.adjust_link		= mt7530_adjust_link,
 	.port_enable		= mt7530_port_enable,
 	.port_disable		= mt7530_port_disable,
 	.port_stp_state_set	= mt7530_stp_state_set,
@@ -1350,6 +1606,11 @@ static const struct dsa_switch_ops mt7530_switch_ops = {
 	.port_vlan_prepare	= mt7530_port_vlan_prepare,
 	.port_vlan_add		= mt7530_port_vlan_add,
 	.port_vlan_del		= mt7530_port_vlan_del,
+	.phylink_validate	= mt7530_phylink_validate,
+	.phylink_mac_link_state = mt7530_phylink_mac_link_state,
+	.phylink_mac_config	= mt7530_phylink_mac_config,
+	.phylink_mac_link_down	= mt7530_phylink_mac_link_down,
+	.phylink_mac_link_up	= mt7530_phylink_mac_link_up,
 };
 
 static const struct of_device_id mt7530_of_match[] = {

drivers/net/dsa/mt7530.h

@@ -186,6 +186,7 @@ enum mt7530_vlan_port_attr {
 /* Register for port MAC control register */
 #define MT7530_PMCR_P(x)		(0x3000 + ((x) * 0x100))
 #define  PMCR_IFG_XMIT(x)		(((x) & 0x3) << 18)
+#define  PMCR_EXT_PHY			BIT(17)
 #define  PMCR_MAC_MODE			BIT(16)
 #define  PMCR_FORCE_MODE		BIT(15)
 #define  PMCR_TX_EN			BIT(14)
@@ -198,26 +199,20 @@ enum mt7530_vlan_port_attr {
 #define  PMCR_FORCE_SPEED_100		BIT(2)
 #define  PMCR_FORCE_FDX			BIT(1)
 #define  PMCR_FORCE_LNK			BIT(0)
-#define  PMCR_COMMON_LINK		(PMCR_IFG_XMIT(1) | PMCR_MAC_MODE | \
-					 PMCR_BACKOFF_EN | PMCR_BACKPR_EN | \
-					 PMCR_TX_EN | PMCR_RX_EN | \
-					 PMCR_TX_FC_EN | PMCR_RX_FC_EN)
-#define  PMCR_CPUP_LINK			(PMCR_COMMON_LINK | PMCR_FORCE_MODE | \
-					 PMCR_FORCE_SPEED_1000 | \
-					 PMCR_FORCE_FDX | \
-					 PMCR_FORCE_LNK)
-#define  PMCR_USERP_LINK		PMCR_COMMON_LINK
-#define  PMCR_FIXED_LINK		(PMCR_IFG_XMIT(1) | PMCR_MAC_MODE | \
-					 PMCR_FORCE_MODE | PMCR_TX_EN | \
-					 PMCR_RX_EN | PMCR_BACKPR_EN | \
-					 PMCR_BACKOFF_EN | \
-					 PMCR_FORCE_SPEED_1000 | \
-					 PMCR_FORCE_FDX | \
-					 PMCR_FORCE_LNK)
-#define PMCR_FIXED_LINK_FC		(PMCR_FIXED_LINK | \
-					 PMCR_TX_FC_EN | PMCR_RX_FC_EN)
+#define  PMCR_SPEED_MASK		(PMCR_FORCE_SPEED_100 | \
+					 PMCR_FORCE_SPEED_1000)
 
 #define MT7530_PMSR_P(x)		(0x3008 + (x) * 0x100)
+#define  PMSR_EEE1G			BIT(7)
+#define  PMSR_EEE100M			BIT(6)
+#define  PMSR_RX_FC			BIT(5)
+#define  PMSR_TX_FC			BIT(4)
+#define  PMSR_SPEED_1000		BIT(3)
+#define  PMSR_SPEED_100			BIT(2)
+#define  PMSR_SPEED_10			0x00
+#define  PMSR_SPEED_MASK		(PMSR_SPEED_100 | PMSR_SPEED_1000)
+#define  PMSR_DPX			BIT(1)
+#define  PMSR_LINK			BIT(0)
 
 /* Register for MIB */
 #define MT7530_PORT_MIB_COUNTER(x)	(0x4000 + (x) * 0x100)
@@ -251,6 +246,7 @@ enum mt7530_vlan_port_attr {
 
 /* Register for hw trap modification */
 #define MT7530_MHWTRAP			0x7804
+#define  MHWTRAP_PHY0_SEL		BIT(20)
 #define  MHWTRAP_MANUAL			BIT(16)
 #define  MHWTRAP_P5_MAC_SEL		BIT(13)
 #define  MHWTRAP_P6_DIS			BIT(8)
@@ -408,6 +404,30 @@ struct mt7530_port {
 	u16 pvid;
 };
 
+/* Port 5 interface select definitions */
+enum p5_interface_select {
+	P5_DISABLED = 0,
+	P5_INTF_SEL_PHY_P0,
+	P5_INTF_SEL_PHY_P4,
+	P5_INTF_SEL_GMAC5,
+};
+
+static const char *p5_intf_modes(unsigned int p5_interface)
+{
+	switch (p5_interface) {
+	case P5_DISABLED:
+		return "DISABLED";
+	case P5_INTF_SEL_PHY_P0:
+		return "PHY P0";
+	case P5_INTF_SEL_PHY_P4:
+		return "PHY P4";
+	case P5_INTF_SEL_GMAC5:
+		return "GMAC5";
+	default:
+		return "unknown";
+	}
+}
+
 /* struct mt7530_priv -	This is the main data structure for holding the state
  *			of the driver
  * @dev:		The device pointer
@@ -423,6 +443,8 @@ struct mt7530_port {
  * @ports:		Holding the state among ports
  * @reg_mutex:		The lock for protecting among process accessing
  *			registers
+ * @p6_interface	Holding the current port 6 interface
+ * @p5_intf_sel:	Holding the current port 5 interface select
  */
 struct mt7530_priv {
 	struct device		*dev;
@@ -435,6 +457,9 @@ struct mt7530_priv {
 	struct gpio_desc	*reset;
 	unsigned int		id;
 	bool			mcm;
+	phy_interface_t		p6_interface;
+	phy_interface_t		p5_interface;
+	unsigned int		p5_intf_sel;
 
 	struct mt7530_port	ports[MT7530_NUM_PORTS];
 	/* protect among processes for registers access*/