ethernet: Remove vf rate limit check for drivers

The commit a14857c2 ("rtnetlink: verify rate parameters for calls to
ndo_set_vf_rate") has been merged to master, so we can to remove the
now-duplicate checks in drivers.
Signed-off-by: Bin Chen <bin.chen@corigine.com>
Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20220609084717.155154-1-simon.horman@corigine.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

drivers/net/ethernet/broadcom/bnxt/bnxt_sriov.c

@@ -307,7 +307,7 @@ int bnxt_set_vf_bw(struct net_device *dev, int vf_id, int min_tx_rate,
 		return -EINVAL;
 	}
 
-	if (min_tx_rate > pf_link_speed || min_tx_rate > max_tx_rate) {
+	if (min_tx_rate > pf_link_speed) {
 		netdev_info(bp->dev, "min tx rate %d is invalid for VF %d\n",
 			    min_tx_rate, vf_id);
 		return -EINVAL;

drivers/net/ethernet/huawei/hinic/hinic_sriov.c

@@ -852,12 +852,6 @@ int hinic_ndo_set_vf_bw(struct net_device *netdev,
 		return -EINVAL;
 	}
 
-	if (max_tx_rate < min_tx_rate) {
-		netif_err(nic_dev, drv, netdev, "Max rate %d must be greater than or equal to min rate %d\n",
-			  max_tx_rate, min_tx_rate);
-		return -EINVAL;
-	}
-
 	err = hinic_port_link_state(nic_dev, &link_state);
 	if (err) {
 		netif_err(nic_dev, drv, netdev,

drivers/net/ethernet/intel/ice/ice_sriov.c

@@ -1593,16 +1593,6 @@ ice_set_vf_bw(struct net_device *netdev, int vf_id, int min_tx_rate,
 		goto out_put_vf;
 	}
 
-	/* when max_tx_rate is zero that means no max Tx rate limiting, so only
-	 * check if max_tx_rate is non-zero
-	 */
-	if (max_tx_rate && min_tx_rate > max_tx_rate) {
-		dev_err(dev, "Cannot set min Tx rate %d Mbps greater than max Tx rate %d Mbps\n",
-			min_tx_rate, max_tx_rate);
-		ret = -EINVAL;
-		goto out_put_vf;
-	}
-
 	if (min_tx_rate && ice_is_dcb_active(pf)) {
 		dev_err(dev, "DCB on PF is currently enabled. VF min Tx rate limiting not allowed on this PF.\n");
 		ret = -EOPNOTSUPP;

drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c

@@ -1869,8 +1869,7 @@ int qlcnic_sriov_set_vf_tx_rate(struct net_device *netdev, int vf,
 	if (!min_tx_rate)
 		min_tx_rate = QLC_VF_MIN_TX_RATE;
 
-	if (max_tx_rate &&
-	    (max_tx_rate >= 10000 || max_tx_rate < min_tx_rate)) {
+	if (max_tx_rate && max_tx_rate >= 10000) {
 		netdev_err(netdev,
 			   "Invalid max Tx rate, allowed range is [%d - %d]",
 			   min_tx_rate, QLC_VF_MAX_TX_RATE);
@@ -1880,8 +1879,7 @@ int qlcnic_sriov_set_vf_tx_rate(struct net_device *netdev, int vf,
 	if (!max_tx_rate)
 		max_tx_rate = 10000;
 
-	if (min_tx_rate &&
-	    (min_tx_rate > max_tx_rate || min_tx_rate < QLC_VF_MIN_TX_RATE)) {
+	if (min_tx_rate && min_tx_rate < QLC_VF_MIN_TX_RATE) {
 		netdev_err(netdev,
 			   "Invalid min Tx rate, allowed range is [%d - %d]",
 			   QLC_VF_MIN_TX_RATE, max_tx_rate);