Merge branch 'powerpc-next' of master.kernel.org:/pub/scm/linux/kernel/git/galak/powerpc

Documentation/powerpc/booting-without-of.txt

@@ -1645,8 +1645,7 @@ platforms are moved over to use the flattened-device-tree model.
    - device_type : should be "network", "hldc", "uart", "transparent"
      "bisync", "atm", or "serial".
    - compatible : could be "ucc_geth" or "fsl_atm" and so on.
-   - model : should be "UCC".
-   - device-id : the ucc number(1-8), corresponding to UCCx in UM.
+   - cell-index : the ucc number(1-8), corresponding to UCCx in UM.
    - reg : Offset and length of the register set for the device
    - interrupts : <a b> where a is the interrupt number and b is a
      field that represents an encoding of the sense and level
@@ -1699,8 +1698,7 @@ platforms are moved over to use the flattened-device-tree model.
 	ucc@2000 {
 		device_type = "network";
 		compatible = "ucc_geth";
-		model = "UCC";
-		device-id = <1>;
+		cell-index = <1>;
 		reg = <2000 200>;
 		interrupts = <a0 0>;
 		interrupt-parent = <700>;

arch/powerpc/Kconfig

@@ -520,6 +520,11 @@ config FSL_PCI
 config 4xx_SOC
 	bool
 
+config FSL_LBC
+	bool
+	help
+	  Freescale Localbus support
+
 # Yes MCA RS/6000s exist but Linux-PPC does not currently support any
 config MCA
 	bool

arch/powerpc/Kconfig.debug

@@ -269,7 +269,7 @@ config PPC_EARLY_DEBUG_CPM_ADDR
 	hex "CPM UART early debug transmit descriptor address"
 	depends on PPC_EARLY_DEBUG_CPM
 	default "0xfa202008" if PPC_EP88XC
-	default "0xf0000008" if CPM2
+	default "0xf0001ff8" if CPM2
 	default "0xff002008" if CPM1
 	help
 	  This specifies the address of the transmit descriptor

arch/powerpc/boot/cpm-serial.c

@@ -11,6 +11,7 @@
 #include "types.h"
 #include "io.h"
 #include "ops.h"
+#include "page.h"
 
 struct cpm_scc {
 	u32 gsmrl;
@@ -42,6 +43,22 @@ struct cpm_param {
 	u16 tbase;
 	u8 rfcr;
 	u8 tfcr;
+	u16 mrblr;
+	u32 rstate;
+	u8 res1[4];
+	u16 rbptr;
+	u8 res2[6];
+	u32 tstate;
+	u8 res3[4];
+	u16 tbptr;
+	u8 res4[6];
+	u16 maxidl;
+	u16 idlc;
+	u16 brkln;
+	u16 brkec;
+	u16 brkcr;
+	u16 rmask;
+	u8 res5[4];
 };
 
 struct cpm_bd {
@@ -54,10 +71,10 @@ static void *cpcr;
 static struct cpm_param *param;
 static struct cpm_smc *smc;
 static struct cpm_scc *scc;
-struct cpm_bd *tbdf, *rbdf;
+static struct cpm_bd *tbdf, *rbdf;
 static u32 cpm_cmd;
-static u8 *muram_start;
-static u32 muram_offset;
+static void *cbd_addr;
+static u32 cbd_offset;
 
 static void (*do_cmd)(int op);
 static void (*enable_port)(void);
@@ -119,20 +136,25 @@ static int cpm_serial_open(void)
 
 	out_8(&param->rfcr, 0x10);
 	out_8(&param->tfcr, 0x10);
-
-	rbdf = (struct cpm_bd *)muram_start;
-	rbdf->addr = (u8 *)(rbdf + 2);
+	out_be16(&param->mrblr, 1);
+	out_be16(&param->maxidl, 0);
+	out_be16(&param->brkec, 0);
+	out_be16(&param->brkln, 0);
+	out_be16(&param->brkcr, 0);
+
+	rbdf = cbd_addr;
+	rbdf->addr = (u8 *)rbdf - 1;
 	rbdf->sc = 0xa000;
 	rbdf->len = 1;
 
 	tbdf = rbdf + 1;
-	tbdf->addr = (u8 *)(rbdf + 2) + 1;
+	tbdf->addr = (u8 *)rbdf - 2;
 	tbdf->sc = 0x2000;
 	tbdf->len = 1;
 
 	sync();
-	out_be16(&param->rbase, muram_offset);
-	out_be16(&param->tbase, muram_offset + sizeof(struct cpm_bd));
+	out_be16(&param->rbase, cbd_offset);
+	out_be16(&param->tbase, cbd_offset + sizeof(struct cpm_bd));
 
 	do_cmd(CPM_CMD_INIT_RX_TX);
 
@@ -175,10 +197,12 @@ static unsigned char cpm_serial_getc(void)
 
 int cpm_console_init(void *devp, struct serial_console_data *scdp)
 {
-	void *reg_virt[2];
-	int is_smc = 0, is_cpm2 = 0, n;
-	unsigned long reg_phys;
+	void *vreg[2];
+	u32 reg[2];
+	int is_smc = 0, is_cpm2 = 0;
 	void *parent, *muram;
+	void *muram_addr;
+	unsigned long muram_offset, muram_size;
 
 	if (dt_is_compatible(devp, "fsl,cpm1-smc-uart")) {
 		is_smc = 1;
@@ -202,63 +226,64 @@ int cpm_console_init(void *devp, struct serial_console_data *scdp)
 	else
 		do_cmd = cpm1_cmd;
 
-	n = getprop(devp, "fsl,cpm-command", &cpm_cmd, 4);
-	if (n < 4)
+	if (getprop(devp, "fsl,cpm-command", &cpm_cmd, 4) < 4)
 		return -1;
 
-	n = getprop(devp, "virtual-reg", reg_virt, sizeof(reg_virt));
-	if (n < (int)sizeof(reg_virt)) {
-		for (n = 0; n < 2; n++) {
-			if (!dt_xlate_reg(devp, n, &reg_phys, NULL))
+	if (dt_get_virtual_reg(devp, vreg, 2) < 2)
 		return -1;
 
-			reg_virt[n] = (void *)reg_phys;
-		}
-	}
-
 	if (is_smc)
-		smc = reg_virt[0];
+		smc = vreg[0];
 	else
-		scc = reg_virt[0];
+		scc = vreg[0];
 
-	param = reg_virt[1];
+	param = vreg[1];
 
 	parent = get_parent(devp);
 	if (!parent)
 		return -1;
 
-	n = getprop(parent, "virtual-reg", reg_virt, sizeof(reg_virt));
-	if (n < (int)sizeof(reg_virt)) {
-		if (!dt_xlate_reg(parent, 0, &reg_phys, NULL))
+	if (dt_get_virtual_reg(parent, &cpcr, 1) < 1)
 		return -1;
 
-		reg_virt[0] = (void *)reg_phys;
-	}
-
-	cpcr = reg_virt[0];
-
 	muram = finddevice("/soc/cpm/muram/data");
 	if (!muram)
 		return -1;
 
 	/* For bootwrapper-compatible device trees, we assume that the first
-	 * entry has at least 18 bytes, and that #address-cells/#data-cells
+	 * entry has at least 128 bytes, and that #address-cells/#data-cells
 	 * is one for both parent and child.
 	 */
 
-	n = getprop(muram, "virtual-reg", reg_virt, sizeof(reg_virt));
-	if (n < (int)sizeof(reg_virt)) {
-		if (!dt_xlate_reg(muram, 0, &reg_phys, NULL))
+	if (dt_get_virtual_reg(muram, &muram_addr, 1) < 1)
 		return -1;
 
-		reg_virt[0] = (void *)reg_phys;
-	}
+	if (getprop(muram, "reg", reg, 8) < 8)
+		return -1;
 
-	muram_start = reg_virt[0];
+	muram_offset = reg[0];
+	muram_size = reg[1];
 
-	n = getprop(muram, "reg", &muram_offset, 4);
-	if (n < 4)
-		return -1;
+	/* Store the buffer descriptors at the end of the first muram chunk.
+	 * For SMC ports on CPM2-based platforms, relocate the parameter RAM
+	 * just before the buffer descriptors.
+	 */
+
+	cbd_offset = muram_offset + muram_size - 2 * sizeof(struct cpm_bd);
+
+	if (is_cpm2 && is_smc) {
+		u16 *smc_base = (u16 *)param;
+		u16 pram_offset;
+
+		pram_offset = cbd_offset - 64;
+		pram_offset = _ALIGN_DOWN(pram_offset, 64);
+
+		disable_port();
+		out_be16(smc_base, pram_offset);
+		param = muram_addr - muram_offset + pram_offset;
+	}
+
+	cbd_addr = muram_addr - muram_offset + cbd_offset;
 
 	scdp->open = cpm_serial_open;
 	scdp->putc = cpm_serial_putc;

arch/powerpc/boot/cuboot-pq2.c

@@ -128,7 +128,7 @@ static void fixup_pci(void)
 	u8 *soc_regs;
 	int i, len;
 	void *node, *parent_node;
-	u32 naddr, nsize, mem_log2;
+	u32 naddr, nsize, mem_pow2, mem_mask;
 
 	node = finddevice("/pci");
 	if (!node || !dt_is_compatible(node, "fsl,pq2-pci"))
@@ -141,7 +141,7 @@ static void fixup_pci(void)
 
 	soc_regs = (u8 *)fsl_get_immr();
 	if (!soc_regs)
-		goto err;
+		goto unhandled;
 
 	dt_get_reg_format(node, &naddr, &nsize);
 	if (naddr != 3 || nsize != 2)
@@ -153,7 +153,7 @@ static void fixup_pci(void)
 
 	dt_get_reg_format(parent_node, &naddr, &nsize);
 	if (naddr != 1 || nsize != 1)
-		goto err;
+		goto unhandled;
 
 	len = getprop(node, "ranges", pci_ranges_buf,
 	              sizeof(pci_ranges_buf));
@@ -170,14 +170,20 @@ static void fixup_pci(void)
 	}
 
 	if (!mem || !mmio || !io)
-		goto err;
+		goto unhandled;
+	if (mem->size[1] != mmio->size[1])
+		goto unhandled;
+	if (mem->size[1] & (mem->size[1] - 1))
+		goto unhandled;
+	if (io->size[1] & (io->size[1] - 1))
+		goto unhandled;
 
 	if (mem->phys_addr + mem->size[1] == mmio->phys_addr)
 		mem_base = mem;
 	else if (mmio->phys_addr + mmio->size[1] == mem->phys_addr)
 		mem_base = mmio;
 	else
-		goto err;
+		goto unhandled;
 
 	out_be32(&pci_regs[1][0], mem_base->phys_addr | 1);
 	out_be32(&pci_regs[2][0], ~(mem->size[1] + mmio->size[1] - 1));
@@ -201,8 +207,9 @@ static void fixup_pci(void)
 	out_le32(&pci_regs[0][58], 0);
 	out_le32(&pci_regs[0][60], 0);
 
-	mem_log2 = 1 << (__ilog2_u32(bd.bi_memsize - 1) + 1);
-	out_le32(&pci_regs[0][62], 0xa0000000 | ~((1 << (mem_log2 - 12)) - 1));
+	mem_pow2 = 1 << (__ilog2_u32(bd.bi_memsize - 1) + 1);
+	mem_mask = ~(mem_pow2 - 1) >> 12;
+	out_le32(&pci_regs[0][62], 0xa0000000 | mem_mask);
 
 	/* If PCI is disabled, drive RST high to enable. */
 	if (!(in_le32(&pci_regs[0][32]) & 1)) {
@@ -228,7 +235,11 @@ static void fixup_pci(void)
 	return;
 
 err:
-	printf("Bad PCI node\r\n");
+	printf("Bad PCI node -- using existing firmware setup.\r\n");
+	return;
+
+unhandled:
+	printf("Unsupported PCI node -- using existing firmware setup.\r\n");
 }
 
 static void pq2_platform_fixups(void)

arch/powerpc/boot/devtree.c

@@ -350,3 +350,23 @@ int dt_is_compatible(void *node, const char *compat)
 
 	return 0;
 }
+
+int dt_get_virtual_reg(void *node, void **addr, int nres)
+{
+	unsigned long xaddr;
+	int n;
+
+	n = getprop(node, "virtual-reg", addr, nres * 4);
+	if (n > 0)
+		return n / 4;
+
+	for (n = 0; n < nres; n++) {
+		if (!dt_xlate_reg(node, n, &xaddr, NULL))
+			break;
+
+		addr[n] = (void *)xaddr;
+	}
+
+	return n;
+}
+

arch/powerpc/boot/dts/ep8248e.dts

@@ -121,8 +121,7 @@ muram {
 
 				data@0 {
 					compatible = "fsl,cpm-muram-data";
-					reg = <0 0x1100 0x1140
-					       0xec0 0x9800 0x800>;
+					reg = <0 0x2000 0x9800 0x800>;
 				};
 			};
 
@@ -138,7 +137,7 @@ smc1: serial@11a80 {
 				device_type = "serial";
 				compatible = "fsl,mpc8248-smc-uart",
 				             "fsl,cpm2-smc-uart";
-				reg = <0x11a80 0x20 0x1100 0x40>;
+				reg = <0x11a80 0x20 0x87fc 2>;
 				interrupts = <4 8>;
 				interrupt-parent = <&PIC>;
 				fsl,cpm-brg = <7>;

arch/powerpc/boot/dts/ep88xc.dts

@@ -2,7 +2,7 @@
  * EP88xC Device Tree Source
  *
  * Copyright 2006 MontaVista Software, Inc.
- * Copyright 2007 Freescale Semiconductor, Inc.
+ * Copyright 2007,2008 Freescale Semiconductor, Inc.
  *
  * This program is free software; you can redistribute  it and/or modify it
  * under  the terms of  the GNU General  Public License as published by the
@@ -10,6 +10,7 @@
  * option) any later version.
  */
 
+/dts-v1/;
 
 / {
 	model = "EP88xC";
@@ -23,44 +24,44 @@ cpus {
 
 		PowerPC,885@0 {
 			device_type = "cpu";
-			reg = <0>;
-			d-cache-line-size = <d#16>;
-			i-cache-line-size = <d#16>;
-			d-cache-size = <d#8192>;
-			i-cache-size = <d#8192>;
+			reg = <0x0>;
+			d-cache-line-size = <16>;
+			i-cache-line-size = <16>;
+			d-cache-size = <8192>;
+			i-cache-size = <8192>;
 			timebase-frequency = <0>;
 			bus-frequency = <0>;
 			clock-frequency = <0>;
-			interrupts = <f 2>;	// decrementer interrupt
+			interrupts = <15 2>;	// decrementer interrupt
 			interrupt-parent = <&PIC>;
 		};
 	};
 
 	memory {
 		device_type = "memory";
-		reg = <0 0>;
+		reg = <0x0 0x0>;
 	};
 
 	localbus@fa200100 {
 		compatible = "fsl,mpc885-localbus", "fsl,pq1-localbus";
 		#address-cells = <2>;
 		#size-cells = <1>;
-		reg = <fa200100 40>;
+		reg = <0xfa200100 0x40>;
 
 		ranges = <
-			0 0 fc000000 04000000
-			3 0 fa000000 01000000
+			0x0 0x0 0xfc000000 0x4000000
+			0x3 0x0 0xfa000000 0x1000000
 		>;
 
 		flash@0,2000000 {
 			compatible = "cfi-flash";
-			reg = <0 2000000 2000000>;
+			reg = <0x0 0x2000000 0x2000000>;
 			bank-width = <4>;
 			device-width = <2>;
 		};
 
 		board-control@3,400000 {
-			reg = <3 400000 10>;
+			reg = <0x3 0x400000 0x10>;
 			compatible = "fsl,ep88xc-bcsr";
 		};
 	};
@@ -70,25 +71,25 @@ soc@fa200000 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		device_type = "soc";
-		ranges = <0 fa200000 00004000>;
+		ranges = <0x0 0xfa200000 0x4000>;
 		bus-frequency = <0>;
 
 		// Temporary -- will go away once kernel uses ranges for get_immrbase().
-		reg = <fa200000 4000>;
+		reg = <0xfa200000 0x4000>;
 
 		mdio@e00 {
 			compatible = "fsl,mpc885-fec-mdio", "fsl,pq1-fec-mdio";
-			reg = <e00 188>;
+			reg = <0xe00 0x188>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 
 			PHY0: ethernet-phy@0 {
-				reg = <0>;
+				reg = <0x0>;
 				device_type = "ethernet-phy";
 			};
 
 			PHY1: ethernet-phy@1 {
-				reg = <1>;
+				reg = <0x1>;
 				device_type = "ethernet-phy";
 			};
 		};
@@ -97,7 +98,7 @@ ethernet@e00 {
 			device_type = "network";
 			compatible = "fsl,mpc885-fec-enet",
 			             "fsl,pq1-fec-enet";
-			reg = <e00 188>;
+			reg = <0xe00 0x188>;
 			local-mac-address = [ 00 00 00 00 00 00 ];
 			interrupts = <3 1>;
 			interrupt-parent = <&PIC>;
@@ -109,7 +110,7 @@ ethernet@1e00 {
 			device_type = "network";
 			compatible = "fsl,mpc885-fec-enet",
 			             "fsl,pq1-fec-enet";
-			reg = <1e00 188>;
+			reg = <0x1e00 0x188>;
 			local-mac-address = [ 00 00 00 00 00 00 ];
 			interrupts = <7 1>;
 			interrupt-parent = <&PIC>;
@@ -120,7 +121,7 @@ ethernet@1e00 {
 		PIC: interrupt-controller@0 {
 			interrupt-controller;
 			#interrupt-cells = <2>;
-			reg = <0 24>;
+			reg = <0x0 0x24>;
 			compatible = "fsl,mpc885-pic", "fsl,pq1-pic";
 		};
 
@@ -130,29 +131,29 @@ pcmcia@80 {
 			#size-cells = <2>;
 			compatible = "fsl,pq-pcmcia";
 			device_type = "pcmcia";
-			reg = <80 80>;
+			reg = <0x80 0x80>;
 			interrupt-parent = <&PIC>;
-			interrupts = <d 1>;
+			interrupts = <13 1>;
 		};
 
 		cpm@9c0 {
 			#address-cells = <1>;
 			#size-cells = <1>;
 			compatible = "fsl,mpc885-cpm", "fsl,cpm1";
-			command-proc = <9c0>;
+			command-proc = <0x9c0>;
 			interrupts = <0>;	// cpm error interrupt
 			interrupt-parent = <&CPM_PIC>;
-			reg = <9c0 40>;
+			reg = <0x9c0 0x40>;
 			ranges;
 
 			muram@2000 {
 				#address-cells = <1>;
 				#size-cells = <1>;
-				ranges = <0 2000 2000>;
+				ranges = <0x0 0x2000 0x2000>;
 
 				data@0 {
 					compatible = "fsl,cpm-muram-data";
-					reg = <0 1c00>;
+					reg = <0x0 0x1c00>;
 				};
 			};
 
@@ -160,7 +161,7 @@ brg@9f0 {
 				compatible = "fsl,mpc885-brg",
 				             "fsl,cpm1-brg",
 				             "fsl,cpm-brg";
-				reg = <9f0 10>;
+				reg = <0x9f0 0x10>;
 			};
 
 			CPM_PIC: interrupt-controller@930 {
@@ -168,7 +169,7 @@ CPM_PIC: interrupt-controller@930 {
 				#interrupt-cells = <1>;
 				interrupts = <5 2 0 2>;
 				interrupt-parent = <&PIC>;
-				reg = <930 20>;
+				reg = <0x930 0x20>;
 				compatible = "fsl,mpc885-cpm-pic",
 				             "fsl,cpm1-pic";
 			};
@@ -178,11 +179,11 @@ serial@a80 {
 				device_type = "serial";
 				compatible = "fsl,mpc885-smc-uart",
 				             "fsl,cpm1-smc-uart";
-				reg = <a80 10 3e80 40>;
+				reg = <0xa80 0x10 0x3e80 0x40>;
 				interrupts = <4>;
 				interrupt-parent = <&CPM_PIC>;
 				fsl,cpm-brg = <1>;
-				fsl,cpm-command = <0090>;
+				fsl,cpm-command = <0x90>;
 				linux,planetcore-label = "SMC1";
 			};
 
@@ -191,11 +192,11 @@ serial@a20 {
 				device_type = "serial";
 				compatible = "fsl,mpc885-scc-uart",
 				             "fsl,cpm1-scc-uart";
-				reg = <a20 20 3d00 80>;
-				interrupts = <1d>;
+				reg = <0xa20 0x20 0x3d00 0x80>;
+				interrupts = <29>;
 				interrupt-parent = <&CPM_PIC>;
 				fsl,cpm-brg = <2>;
-				fsl,cpm-command = <0040>;
+				fsl,cpm-command = <0x40>;
 				linux,planetcore-label = "SCC2";
 			};
 
@@ -204,9 +205,9 @@ usb@a00 {
 				#size-cells = <0>;
 				compatible = "fsl,mpc885-usb",
 				             "fsl,cpm1-usb";
-				reg = <a00 18 1c00 80>;
+				reg = <0xa00 0x18 0x1c00 0x80>;
 				interrupt-parent = <&CPM_PIC>;
-				interrupts = <1e>;
+				interrupts = <30>;
 				fsl,cpm-command = <0000>;
 			};
 		};

arch/powerpc/boot/dts/kuroboxHD.dts

@@ -7,6 +7,7 @@
  * Based on sandpoint.dts
  *
  * 2006 (c) G. Liakhovetski <g.liakhovetski@gmx.de>
+ * Copyright 2008 Freescale Semiconductor, Inc.
  *
  * This file is licensed under
  * the terms of the GNU General Public License version 2.  This program
@@ -17,6 +18,8 @@ XXXX add flash parts, rtc, ??
 
  */
 
+/dts-v1/;
+
 / {
 	model = "KuroboxHD";
 	compatible = "linkstation";
@@ -35,19 +38,19 @@ cpus {
 
 		PowerPC,603e { /* Really 8241 */
 			device_type = "cpu";
-			reg = <0>;
-			clock-frequency = <bebc200>;	/* Fixed by bootloader */
-			timebase-frequency = <1743000>; /* Fixed by bootloader */
+			reg = <0x0>;
+			clock-frequency = <200000000>;	/* Fixed by bootloader */
+			timebase-frequency = <24391680>; /* Fixed by bootloader */
 			bus-frequency = <0>;		/* Fixed by bootloader */
 			/* Following required by dtc but not used */
-			i-cache-size = <4000>;
-			d-cache-size = <4000>;
+			i-cache-size = <0x4000>;
+			d-cache-size = <0x4000>;
 		};
 	};
 
 	memory {
 		device_type = "memory";
-		reg = <00000000 04000000>;
+		reg = <0x0 0x4000000>;
 	};
 
 	soc10x { /* AFAICT need to make soc for 8245's uarts to be defined */
@@ -56,26 +59,26 @@ soc10x { /* AFAICT need to make soc for 8245's uarts to be defined */
 		device_type = "soc";
 		compatible = "mpc10x";
 		store-gathering = <0>; /* 0 == off, !0 == on */
-		reg = <80000000 00100000>;
-		ranges = <80000000 80000000 70000000	/* pci mem space */
-			  fc000000 fc000000 00100000	/* EUMB */
-			  fe000000 fe000000 00c00000	/* pci i/o space */
-			  fec00000 fec00000 00300000	/* pci cfg regs */
-			  fef00000 fef00000 00100000>;	/* pci iack */
+		reg = <0x80000000 0x100000>;
+		ranges = <0x80000000 0x80000000 0x70000000	/* pci mem space */
+			  0xfc000000 0xfc000000 0x100000	/* EUMB */
+			  0xfe000000 0xfe000000 0xc00000	/* pci i/o space */
+			  0xfec00000 0xfec00000 0x300000	/* pci cfg regs */
+			  0xfef00000 0xfef00000 0x100000>;	/* pci iack */
 
 		i2c@80003000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			cell-index = <0>;
 			compatible = "fsl-i2c";
-			reg = <80003000 1000>;
+			reg = <0x80003000 0x1000>;
 			interrupts = <5 2>;
 			interrupt-parent = <&mpic>;
 
 			rtc@32 {
 				device_type = "rtc";
 				compatible = "ricoh,rs5c372a";
-				reg = <32>;
+				reg = <0x32>;
 			};
 		};
 
@@ -83,9 +86,9 @@ serial0: serial@80004500 {
 			cell-index = <0>;
 			device_type = "serial";
 			compatible = "ns16550";
-			reg = <80004500 8>;
-			clock-frequency = <5d08d88>;
-			current-speed = <2580>;
+			reg = <0x80004500 0x8>;
+			clock-frequency = <97553800>;
+			current-speed = <9600>;
 			interrupts = <9 0>;
 			interrupt-parent = <&mpic>;
 		};
@@ -94,10 +97,10 @@ serial1: serial@80004600 {
 			cell-index = <1>;
 			device_type = "serial";
 			compatible = "ns16550";
-			reg = <80004600 8>;
-			clock-frequency = <5d08d88>;
-			current-speed = <e100>;
-			interrupts = <a 0>;
+			reg = <0x80004600 0x8>;
+			clock-frequency = <97553800>;
+			current-speed = <57600>;
+			interrupts = <10 0>;
 			interrupt-parent = <&mpic>;
 		};
 
@@ -107,7 +110,7 @@ mpic: interrupt-controller@80040000 {
 			device_type = "open-pic";
 			compatible = "chrp,open-pic";
 			interrupt-controller;
-			reg = <80040000 40000>;
+			reg = <0x80040000 0x40000>;
 		};
 
 		pci0: pci@fec00000 {
@@ -116,29 +119,29 @@ pci0: pci@fec00000 {
 			#interrupt-cells = <1>;
 			device_type = "pci";
 			compatible = "mpc10x-pci";
-			reg = <fec00000 400000>;
-			ranges = <01000000 0        0 fe000000 0 00c00000
-				  02000000 0 80000000 80000000 0 70000000>;
-			bus-range = <0 ff>;
-			clock-frequency = <7f28155>;
+			reg = <0xfec00000 0x400000>;
+			ranges = <0x1000000 0x0        0x0 0xfe000000 0x0 0xc00000
+				  0x2000000 0x0 0x80000000 0x80000000 0x0 0x70000000>;
+			bus-range = <0 255>;
+			clock-frequency = <133333333>;
 			interrupt-parent = <&mpic>;
-			interrupt-map-mask = <f800 0 0 7>;
+			interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
 			interrupt-map = <
 				/* IDSEL 11 - IRQ0 ETH */
-				5800 0 0 1 &mpic 0 1
-				5800 0 0 2 &mpic 1 1
-				5800 0 0 3 &mpic 2 1
-				5800 0 0 4 &mpic 3 1
+				0x5800 0x0 0x0 0x1 &mpic 0x0 0x1
+				0x5800 0x0 0x0 0x2 &mpic 0x1 0x1
+				0x5800 0x0 0x0 0x3 &mpic 0x2 0x1
+				0x5800 0x0 0x0 0x4 &mpic 0x3 0x1
 				/* IDSEL 12 - IRQ1 IDE0 */
-				6000 0 0 1 &mpic 1 1
-				6000 0 0 2 &mpic 2 1
-				6000 0 0 3 &mpic 3 1
-				6000 0 0 4 &mpic 0 1
+				0x6000 0x0 0x0 0x1 &mpic 0x1 0x1
+				0x6000 0x0 0x0 0x2 &mpic 0x2 0x1
+				0x6000 0x0 0x0 0x3 &mpic 0x3 0x1
+				0x6000 0x0 0x0 0x4 &mpic 0x0 0x1
 				/* IDSEL 14 - IRQ3 USB2.0 */
-				7000 0 0 1 &mpic 3 1
-				7000 0 0 2 &mpic 3 1
-				7000 0 0 3 &mpic 3 1
-				7000 0 0 4 &mpic 3 1
+				0x7000 0x0 0x0 0x1 &mpic 0x3 0x1
+				0x7000 0x0 0x0 0x2 &mpic 0x3 0x1
+				0x7000 0x0 0x0 0x3 &mpic 0x3 0x1
+				0x7000 0x0 0x0 0x4 &mpic 0x3 0x1
 			>;
 		};
 	};

arch/powerpc/boot/dts/kuroboxHG.dts

@@ -7,6 +7,7 @@
  * Based on sandpoint.dts
  *
  * 2006 (c) G. Liakhovetski <g.liakhovetski@gmx.de>
+ * Copyright 2008 Freescale Semiconductor, Inc.
  *
  * This file is licensed under
  * the terms of the GNU General Public License version 2.  This program
@@ -17,6 +18,8 @@ XXXX add flash parts, rtc, ??
 
  */
 
+/dts-v1/;
+
 / {
 	model = "KuroboxHG";
 	compatible = "linkstation";
@@ -35,19 +38,19 @@ cpus {
 
 		PowerPC,603e { /* Really 8241 */
 			device_type = "cpu";
-			reg = <0>;
-			clock-frequency = <fdad680>;	/* Fixed by bootloader */
-			timebase-frequency = <1F04000>; /* Fixed by bootloader */
+			reg = <0x0>;
+			clock-frequency = <266000000>;	/* Fixed by bootloader */
+			timebase-frequency = <32522240>; /* Fixed by bootloader */
 			bus-frequency = <0>;		/* Fixed by bootloader */
 			/* Following required by dtc but not used */
-			i-cache-size = <4000>;
-			d-cache-size = <4000>;
+			i-cache-size = <0x4000>;
+			d-cache-size = <0x4000>;
 		};
 	};
 
 	memory {
 		device_type = "memory";
-		reg = <00000000 08000000>;
+		reg = <0x0 0x8000000>;
 	};
 
 	soc10x { /* AFAICT need to make soc for 8245's uarts to be defined */
@@ -56,26 +59,26 @@ soc10x { /* AFAICT need to make soc for 8245's uarts to be defined */
 		device_type = "soc";
 		compatible = "mpc10x";
 		store-gathering = <0>; /* 0 == off, !0 == on */
-		reg = <80000000 00100000>;
-		ranges = <80000000 80000000 70000000	/* pci mem space */
-			  fc000000 fc000000 00100000	/* EUMB */
-			  fe000000 fe000000 00c00000	/* pci i/o space */
-			  fec00000 fec00000 00300000	/* pci cfg regs */
-			  fef00000 fef00000 00100000>;	/* pci iack */
+		reg = <0x80000000 0x100000>;
+		ranges = <0x80000000 0x80000000 0x70000000	/* pci mem space */
+			  0xfc000000 0xfc000000 0x100000	/* EUMB */
+			  0xfe000000 0xfe000000 0xc00000	/* pci i/o space */
+			  0xfec00000 0xfec00000 0x300000	/* pci cfg regs */
+			  0xfef00000 0xfef00000 0x100000>;	/* pci iack */
 
 		i2c@80003000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			cell-index = <0>;
 			compatible = "fsl-i2c";
-			reg = <80003000 1000>;
+			reg = <0x80003000 0x1000>;
 			interrupts = <5 2>;
 			interrupt-parent = <&mpic>;
 
 			rtc@32 {
 				device_type = "rtc";
 				compatible = "ricoh,rs5c372a";
-				reg = <32>;
+				reg = <0x32>;
 			};
 		};
 
@@ -83,9 +86,9 @@ serial0: serial@80004500 {
 			cell-index = <0>;
 			device_type = "serial";
 			compatible = "ns16550";
-			reg = <80004500 8>;
-			clock-frequency = <7c044a8>;
-			current-speed = <2580>;
+			reg = <0x80004500 0x8>;
+			clock-frequency = <130041000>;
+			current-speed = <9600>;
 			interrupts = <9 0>;
 			interrupt-parent = <&mpic>;
 		};
@@ -94,10 +97,10 @@ serial1: serial@80004600 {
 			cell-index = <1>;
 			device_type = "serial";
 			compatible = "ns16550";
-			reg = <80004600 8>;
-			clock-frequency = <7c044a8>;
-			current-speed = <e100>;
-			interrupts = <a 0>;
+			reg = <0x80004600 0x8>;
+			clock-frequency = <130041000>;
+			current-speed = <57600>;
+			interrupts = <10 0>;
 			interrupt-parent = <&mpic>;
 		};
 
@@ -107,7 +110,7 @@ mpic: interrupt-controller@80040000 {
 			device_type = "open-pic";
 			compatible = "chrp,open-pic";
 			interrupt-controller;
-			reg = <80040000 40000>;
+			reg = <0x80040000 0x40000>;
 		};
 
 		pci0: pci@fec00000 {
@@ -116,29 +119,29 @@ pci0: pci@fec00000 {
 			#interrupt-cells = <1>;
 			device_type = "pci";
 			compatible = "mpc10x-pci";
-			reg = <fec00000 400000>;
-			ranges = <01000000 0        0 fe000000 0 00c00000
-				  02000000 0 80000000 80000000 0 70000000>;
-			bus-range = <0 ff>;
-			clock-frequency = <7f28155>;
+			reg = <0xfec00000 0x400000>;
+			ranges = <0x1000000 0x0        0x0 0xfe000000 0x0 0xc00000
+				  0x2000000 0x0 0x80000000 0x80000000 0x0 0x70000000>;
+			bus-range = <0 255>;
+			clock-frequency = <133333333>;
 			interrupt-parent = <&mpic>;
-			interrupt-map-mask = <f800 0 0 7>;
+			interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
 			interrupt-map = <
 				/* IDSEL 11 - IRQ0 ETH */
-				5800 0 0 1 &mpic 0 1
-				5800 0 0 2 &mpic 1 1
-				5800 0 0 3 &mpic 2 1
-				5800 0 0 4 &mpic 3 1
+				0x5800 0x0 0x0 0x1 &mpic 0x0 0x1
+				0x5800 0x0 0x0 0x2 &mpic 0x1 0x1
+				0x5800 0x0 0x0 0x3 &mpic 0x2 0x1
+				0x5800 0x0 0x0 0x4 &mpic 0x3 0x1
 				/* IDSEL 12 - IRQ1 IDE0 */
-				6000 0 0 1 &mpic 1 1
-				6000 0 0 2 &mpic 2 1
-				6000 0 0 3 &mpic 3 1
-				6000 0 0 4 &mpic 0 1
+				0x6000 0x0 0x0 0x1 &mpic 0x1 0x1
+				0x6000 0x0 0x0 0x2 &mpic 0x2 0x1
+				0x6000 0x0 0x0 0x3 &mpic 0x3 0x1
+				0x6000 0x0 0x0 0x4 &mpic 0x0 0x1
 				/* IDSEL 14 - IRQ3 USB2.0 */
-				7000 0 0 1 &mpic 3 1
-				7000 0 0 2 &mpic 3 1
-				7000 0 0 3 &mpic 3 1
-				7000 0 0 4 &mpic 3 1
+				0x7000 0x0 0x0 0x1 &mpic 0x3 0x1
+				0x7000 0x0 0x0 0x2 &mpic 0x3 0x1
+				0x7000 0x0 0x0 0x3 &mpic 0x3 0x1
+				0x7000 0x0 0x0 0x4 &mpic 0x3 0x1
 			>;
 		};
 	};

arch/powerpc/boot/dts/mpc7448hpc2.dts

 /*
  * MPC7448HPC2 (Taiga) board Device Tree Source
  *
- * Copyright 2006 Freescale Semiconductor Inc.
+ * Copyright 2006, 2008 Freescale Semiconductor Inc.
  * 2006 Roy Zang <Roy Zang at freescale.com>.
  *
  * This program is free software; you can redistribute  it and/or modify it
@@ -10,6 +10,7 @@
  * option) any later version.
  */
 
+/dts-v1/;
 
 / {
 	model = "mpc7448hpc2";
@@ -23,11 +24,11 @@ cpus {
 				
 		PowerPC,7448@0 {
 			device_type = "cpu";
-			reg = <0>;
-			d-cache-line-size = <20>;	// 32 bytes
-			i-cache-line-size = <20>;	// 32 bytes
-			d-cache-size = <8000>;		// L1, 32K bytes
-			i-cache-size = <8000>;		// L1, 32K bytes
+			reg = <0x0>;
+			d-cache-line-size = <32>;	// 32 bytes
+			i-cache-line-size = <32>;	// 32 bytes
+			d-cache-size = <0x8000>;		// L1, 32K bytes
+			i-cache-size = <0x8000>;		// L1, 32K bytes
 			timebase-frequency = <0>;	// 33 MHz, from uboot
 			clock-frequency = <0>;		// From U-Boot
 			bus-frequency = <0>;		// From U-Boot
@@ -36,7 +37,7 @@ PowerPC,7448@0 {
 
 	memory {
 		device_type = "memory";
-		reg = <00000000 20000000	// DDR2   512M at 0
+		reg = <0x0 0x20000000	// DDR2   512M at 0
 		       >;
 	};
 
@@ -44,14 +45,14 @@ tsi108@c0000000 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		device_type = "tsi-bridge";
-		ranges = <00000000 c0000000 00010000>;
-		reg = <c0000000 00010000>;
+		ranges = <0x0 0xc0000000 0x10000>;
+		reg = <0xc0000000 0x10000>;
 		bus-frequency = <0>;
 
 		i2c@7000 {
 			interrupt-parent = <&mpic>;
-			interrupts = <E 0>;
-			reg = <7000 400>;
+			interrupts = <14 0>;
+			reg = <0x7000 0x400>;
 			device_type = "i2c";
 			compatible  = "tsi108-i2c";
 		};
@@ -59,20 +60,20 @@ i2c@7000 {
 		MDIO: mdio@6000 {
 			device_type = "mdio";
 			compatible = "tsi108-mdio";
-			reg = <6000 50>;
+			reg = <0x6000 0x50>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 
 			phy8: ethernet-phy@8 {
 				interrupt-parent = <&mpic>;
 				interrupts = <2 1>;
-				reg = <8>;
+				reg = <0x8>;
 			};
 
 			phy9: ethernet-phy@9 {
 				interrupt-parent = <&mpic>;
 				interrupts = <2 1>;
-				reg = <9>;
+				reg = <0x9>;
 			};
 
 		};
@@ -82,9 +83,9 @@ ethernet@6200 {
 			#size-cells = <0>;
 			device_type = "network";
 			compatible = "tsi108-ethernet";
-			reg = <6000 200>;
+			reg = <0x6000 0x200>;
 			address = [ 00 06 D2 00 00 01 ];
-			interrupts = <10 2>;
+			interrupts = <16 2>;
 			interrupt-parent = <&mpic>;
 			mdio-handle = <&MDIO>;
 			phy-handle = <&phy8>;
@@ -96,9 +97,9 @@ ethernet@6600 {
 			#size-cells = <0>;
 			device_type = "network";
 			compatible = "tsi108-ethernet";
-			reg = <6400 200>;
+			reg = <0x6400 0x200>;
 			address = [ 00 06 D2 00 00 02 ];
-			interrupts = <11 2>;
+			interrupts = <17 2>;
 			interrupt-parent = <&mpic>;
 			mdio-handle = <&MDIO>;
 			phy-handle = <&phy9>;
@@ -107,18 +108,18 @@ ethernet@6600 {
 		serial@7808 {
 			device_type = "serial";
 			compatible = "ns16550";
-			reg = <7808 200>;
-			clock-frequency = <3f6b5a00>;
-			interrupts = <c 0>;
+			reg = <0x7808 0x200>;
+			clock-frequency = <1064000000>;
+			interrupts = <12 0>;
 			interrupt-parent = <&mpic>;
 		};
 
 		serial@7c08 {
 			device_type = "serial";
 			compatible = "ns16550";
-			reg = <7c08 200>;
-			clock-frequency = <3f6b5a00>;
-			interrupts = <d 0>;
+			reg = <0x7c08 0x200>;
+			clock-frequency = <1064000000>;
+			interrupts = <13 0>;
 			interrupt-parent = <&mpic>;
 		};
 
@@ -127,7 +128,7 @@ mpic: pic@7400 {
 			interrupt-controller;
 			#address-cells = <0>;
 			#interrupt-cells = <2>;
-			reg = <7400 400>;
+			reg = <0x7400 0x400>;
 			compatible = "chrp,open-pic";
 			device_type = "open-pic";
                        	big-endian;
@@ -138,39 +139,39 @@ pci@1000 {
 			#interrupt-cells = <1>;
 			#size-cells = <2>;
 			#address-cells = <3>;
-			reg = <1000 1000>;
+			reg = <0x1000 0x1000>;
 			bus-range = <0 0>;
-			ranges = <02000000 0 e0000000 e0000000 0 1A000000	
-				  01000000 0 00000000 fa000000 0 00010000>;
-			clock-frequency = <7f28154>;
+			ranges = <0x2000000 0x0 0xe0000000 0xe0000000 0x0 0x1a000000	
+				  0x1000000 0x0 0x0 0xfa000000 0x0 0x10000>;
+			clock-frequency = <133333332>;
 			interrupt-parent = <&mpic>;
-			interrupts = <17 2>;
-			interrupt-map-mask = <f800 0 0 7>;
+			interrupts = <23 2>;
+			interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
 			interrupt-map = <
 
 				/* IDSEL 0x11 */
-				0800 0 0 1 &RT0 24 0
-				0800 0 0 2 &RT0 25 0
-				0800 0 0 3 &RT0 26 0
-				0800 0 0 4 &RT0 27 0
+				0x800 0x0 0x0 0x1 &RT0 0x24 0x0
+				0x800 0x0 0x0 0x2 &RT0 0x25 0x0
+				0x800 0x0 0x0 0x3 &RT0 0x26 0x0
+				0x800 0x0 0x0 0x4 &RT0 0x27 0x0
 
 				/* IDSEL 0x12 */
-				1000 0 0 1 &RT0 25 0
-				1000 0 0 2 &RT0 26 0
-				1000 0 0 3 &RT0 27 0
-				1000 0 0 4 &RT0 24 0
+				0x1000 0x0 0x0 0x1 &RT0 0x25 0x0
+				0x1000 0x0 0x0 0x2 &RT0 0x26 0x0
+				0x1000 0x0 0x0 0x3 &RT0 0x27 0x0
+				0x1000 0x0 0x0 0x4 &RT0 0x24 0x0
 
 				/* IDSEL 0x13 */
-				1800 0 0 1 &RT0 26 0
-				1800 0 0 2 &RT0 27 0
-				1800 0 0 3 &RT0 24 0
-				1800 0 0 4 &RT0 25 0
+				0x1800 0x0 0x0 0x1 &RT0 0x26 0x0
+				0x1800 0x0 0x0 0x2 &RT0 0x27 0x0
+				0x1800 0x0 0x0 0x3 &RT0 0x24 0x0
+				0x1800 0x0 0x0 0x4 &RT0 0x25 0x0
 
 				/* IDSEL 0x14 */
-				2000 0 0 1 &RT0 27 0
-				2000 0 0 2 &RT0 24 0
-				2000 0 0 3 &RT0 25 0
-				2000 0 0 4 &RT0 26 0
+				0x2000 0x0 0x0 0x1 &RT0 0x27 0x0
+				0x2000 0x0 0x0 0x2 &RT0 0x24 0x0
+				0x2000 0x0 0x0 0x3 &RT0 0x25 0x0
+				0x2000 0x0 0x0 0x4 &RT0 0x26 0x0
 				>;
 
 			RT0: router@1180 {
@@ -180,7 +181,7 @@ RT0: router@1180 {
 				#address-cells = <0>;
 				#interrupt-cells = <2>;
 				big-endian;
-				interrupts = <17 2>;
+				interrupts = <23 2>;
 				interrupt-parent = <&mpic>;
 			};
 		};

arch/powerpc/boot/dts/mpc8272ads.dts

 /*
  * MPC8272 ADS Device Tree Source
  *
- * Copyright 2005 Freescale Semiconductor Inc.
+ * Copyright 2005,2008 Freescale Semiconductor Inc.
  *
  * This program is free software; you can redistribute  it and/or modify it
  * under  the terms of  the GNU General  Public License as published by the
@@ -9,6 +9,8 @@
  * option) any later version.
  */
 
+/dts-v1/;
+
 / {
 	model = "MPC8272ADS";
 	compatible = "fsl,mpc8272ads";
@@ -21,11 +23,11 @@ cpus {
 
 		PowerPC,8272@0 {
 			device_type = "cpu";
-			reg = <0>;
-			d-cache-line-size = <d#32>;
-			i-cache-line-size = <d#32>;
-			d-cache-size = <d#16384>;
-			i-cache-size = <d#16384>;
+			reg = <0x0>;
+			d-cache-line-size = <32>;
+			i-cache-line-size = <32>;
+			d-cache-size = <16384>;
+			i-cache-size = <16384>;
 			timebase-frequency = <0>;
 			bus-frequency = <0>;
 			clock-frequency = <0>;
@@ -34,7 +36,7 @@ PowerPC,8272@0 {
 
 	memory {
 		device_type = "memory";
-		reg = <0 0>;
+		reg = <0x0 0x0>;
 	};
 
 	localbus@f0010100 {
@@ -42,21 +44,21 @@ localbus@f0010100 {
 		             "fsl,pq2-localbus";
 		#address-cells = <2>;
 		#size-cells = <1>;
-		reg = <f0010100 40>;
+		reg = <0xf0010100 0x40>;
 
-		ranges = <0 0 fe000000 02000000
-		          1 0 f4500000 00008000
-		          3 0 f8200000 00008000>;
+		ranges = <0x0 0x0 0xfe000000 0x2000000
+		          0x1 0x0 0xf4500000 0x8000
+		          0x3 0x0 0xf8200000 0x8000>;
 
 		flash@0,0 {
 			compatible = "jedec-flash";
-			reg = <0 0 2000000>;
+			reg = <0x0 0x0 0x2000000>;
 			bank-width = <4>;
 			device-width = <1>;
 		};
 
 		board-control@1,0 {
-			reg = <1 0 20>;
+			reg = <0x1 0x0 0x20>;
 			compatible = "fsl,mpc8272ads-bcsr";
 		};
 
@@ -65,46 +67,46 @@ PCI_PIC: interrupt-controller@3,0 {
 			             "fsl,pq2ads-pci-pic";
 			#interrupt-cells = <1>;
 			interrupt-controller;
-			reg = <3 0 8>;
+			reg = <0x3 0x0 0x8>;
 			interrupt-parent = <&PIC>;
-			interrupts = <14 8>;
+			interrupts = <20 8>;
 		};
 	};
 
 
 	pci@f0010800 {
 		device_type = "pci";
-		reg = <f0010800 10c f00101ac 8 f00101c4 8>;
+		reg = <0xf0010800 0x10c 0xf00101ac 0x8 0xf00101c4 0x8>;
 		compatible = "fsl,mpc8272-pci", "fsl,pq2-pci";
 		#interrupt-cells = <1>;
 		#size-cells = <2>;
 		#address-cells = <3>;
-		clock-frequency = <d#66666666>;
-		interrupt-map-mask = <f800 0 0 7>;
+		clock-frequency = <66666666>;
+		interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
 		interrupt-map = <
 		                 /* IDSEL 0x16 */
-		                 b000 0 0 1 &PCI_PIC 0
-		                 b000 0 0 2 &PCI_PIC 1
-		                 b000 0 0 3 &PCI_PIC 2
-		                 b000 0 0 4 &PCI_PIC 3
+		                 0xb000 0x0 0x0 0x1 &PCI_PIC 0
+		                 0xb000 0x0 0x0 0x2 &PCI_PIC 1
+		                 0xb000 0x0 0x0 0x3 &PCI_PIC 2
+		                 0xb000 0x0 0x0 0x4 &PCI_PIC 3
 
 		                 /* IDSEL 0x17 */
-		                 b800 0 0 1 &PCI_PIC 4
-		                 b800 0 0 2 &PCI_PIC 5
-		                 b800 0 0 3 &PCI_PIC 6
-		                 b800 0 0 4 &PCI_PIC 7
+		                 0xb800 0x0 0x0 0x1 &PCI_PIC 4
+		                 0xb800 0x0 0x0 0x2 &PCI_PIC 5
+		                 0xb800 0x0 0x0 0x3 &PCI_PIC 6
+		                 0xb800 0x0 0x0 0x4 &PCI_PIC 7
 
 		                 /* IDSEL 0x18 */
-		                 c000 0 0 1 &PCI_PIC 8
-		                 c000 0 0 2 &PCI_PIC 9
-		                 c000 0 0 3 &PCI_PIC a
-		                 c000 0 0 4 &PCI_PIC b>;
+		                 0xc000 0x0 0x0 0x1 &PCI_PIC 8
+		                 0xc000 0x0 0x0 0x2 &PCI_PIC 9
+		                 0xc000 0x0 0x0 0x3 &PCI_PIC 10
+		                 0xc000 0x0 0x0 0x4 &PCI_PIC 11>;
 
 		interrupt-parent = <&PIC>;
-		interrupts = <12 8>;
-		ranges = <42000000 0 80000000 80000000 0 20000000
-		          02000000 0 a0000000 a0000000 0 20000000
-		          01000000 0 00000000 f6000000 0 02000000>;
+		interrupts = <18 8>;
+		ranges = <0x42000000 0x0 0x80000000 0x80000000 0x0 0x20000000
+		          0x2000000 0x0 0xa0000000 0xa0000000 0x0 0x20000000
+		          0x1000000 0x0 0x0 0xf6000000 0x0 0x2000000>;
 	};
 
 	soc@f0000000 {
@@ -112,26 +114,26 @@ soc@f0000000 {
 		#size-cells = <1>;
 		device_type = "soc";
 		compatible = "fsl,mpc8272", "fsl,pq2-soc";
-		ranges = <00000000 f0000000 00053000>;
+		ranges = <0x0 0xf0000000 0x53000>;
 
 		// Temporary -- will go away once kernel uses ranges for get_immrbase().
-		reg = <f0000000 00053000>;
+		reg = <0xf0000000 0x53000>;
 
 		cpm@119c0 {
 			#address-cells = <1>;
 			#size-cells = <1>;
 			compatible = "fsl,mpc8272-cpm", "fsl,cpm2";
-			reg = <119c0 30>;
+			reg = <0x119c0 0x30>;
 			ranges;
 
 			muram@0 {
 				#address-cells = <1>;
 				#size-cells = <1>;
-				ranges = <0 0 10000>;
+				ranges = <0x0 0x0 0x10000>;
 
 				data@0 {
 					compatible = "fsl,cpm-muram-data";
-					reg = <0 2000 9800 800>;
+					reg = <0x0 0x2000 0x9800 0x800>;
 				};
 			};
 
@@ -139,29 +141,29 @@ brg@119f0 {
 				compatible = "fsl,mpc8272-brg",
 				             "fsl,cpm2-brg",
 				             "fsl,cpm-brg";
-				reg = <119f0 10 115f0 10>;
+				reg = <0x119f0 0x10 0x115f0 0x10>;
 			};
 
 			serial@11a00 {
 				device_type = "serial";
 				compatible = "fsl,mpc8272-scc-uart",
 				             "fsl,cpm2-scc-uart";
-				reg = <11a00 20 8000 100>;
-				interrupts = <28 8>;
+				reg = <0x11a00 0x20 0x8000 0x100>;
+				interrupts = <40 8>;
 				interrupt-parent = <&PIC>;
 				fsl,cpm-brg = <1>;
-				fsl,cpm-command = <00800000>;
+				fsl,cpm-command = <0x800000>;
 			};
 
 			serial@11a60 {
 				device_type = "serial";
 				compatible = "fsl,mpc8272-scc-uart",
 				             "fsl,cpm2-scc-uart";
-				reg = <11a60 20 8300 100>;
-				interrupts = <2b 8>;
+				reg = <0x11a60 0x20 0x8300 0x100>;
+				interrupts = <43 8>;
 				interrupt-parent = <&PIC>;
 				fsl,cpm-brg = <4>;
-				fsl,cpm-command = <0ce00000>;
+				fsl,cpm-command = <0xce00000>;
 			};
 
 			mdio@10d40 {
@@ -169,23 +171,23 @@ mdio@10d40 {
 				compatible = "fsl,mpc8272ads-mdio-bitbang",
 				             "fsl,mpc8272-mdio-bitbang",
 				             "fsl,cpm2-mdio-bitbang";
-				reg = <10d40 14>;
+				reg = <0x10d40 0x14>;
 				#address-cells = <1>;
 				#size-cells = <0>;
-				fsl,mdio-pin = <12>;
-				fsl,mdc-pin = <13>;
+				fsl,mdio-pin = <18>;
+				fsl,mdc-pin = <19>;
 
 				PHY0: ethernet-phy@0 {
 					interrupt-parent = <&PIC>;
-					interrupts = <17 8>;
-					reg = <0>;
+					interrupts = <23 8>;
+					reg = <0x0>;
 					device_type = "ethernet-phy";
 				};
 
 				PHY1: ethernet-phy@1 {
 					interrupt-parent = <&PIC>;
-					interrupts = <17 8>;
-					reg = <3>;
+					interrupts = <23 8>;
+					reg = <0x3>;
 					device_type = "ethernet-phy";
 				};
 			};
@@ -194,33 +196,33 @@ ethernet@11300 {
 				device_type = "network";
 				compatible = "fsl,mpc8272-fcc-enet",
 				             "fsl,cpm2-fcc-enet";
-				reg = <11300 20 8400 100 11390 1>;
+				reg = <0x11300 0x20 0x8400 0x100 0x11390 0x1>;
 				local-mac-address = [ 00 00 00 00 00 00 ];
-				interrupts = <20 8>;
+				interrupts = <32 8>;
 				interrupt-parent = <&PIC>;
 				phy-handle = <&PHY0>;
 				linux,network-index = <0>;
-				fsl,cpm-command = <12000300>;
+				fsl,cpm-command = <0x12000300>;
 			};
 
 			ethernet@11320 {
 				device_type = "network";
 				compatible = "fsl,mpc8272-fcc-enet",
 				             "fsl,cpm2-fcc-enet";
-				reg = <11320 20 8500 100 113b0 1>;
+				reg = <0x11320 0x20 0x8500 0x100 0x113b0 0x1>;
 				local-mac-address = [ 00 00 00 00 00 00 ];
-				interrupts = <21 8>;
+				interrupts = <33 8>;
 				interrupt-parent = <&PIC>;
 				phy-handle = <&PHY1>;
 				linux,network-index = <1>;
-				fsl,cpm-command = <16200300>;
+				fsl,cpm-command = <0x16200300>;
 			};
 		};
 
 		PIC: interrupt-controller@10c00 {
 			#interrupt-cells = <2>;
 			interrupt-controller;
-			reg = <10c00 80>;
+			reg = <0x10c00 0x80>;
 			compatible = "fsl,mpc8272-pic", "fsl,cpm2-pic";
 		};
 
@@ -232,14 +234,14 @@ crypto@30000 {
 			             "fsl,talitos-sec2",
 			             "fsl,talitos",
 			             "talitos";
-			reg = <30000 10000>;
-			interrupts = <b 8>;
+			reg = <0x30000 0x10000>;
+			interrupts = <11 8>;
 			interrupt-parent = <&PIC>;
 			num-channels = <4>;
-			channel-fifo-len = <18>;
-			exec-units-mask = <0000007e>;
+			channel-fifo-len = <24>;
+			exec-units-mask = <0x7e>;
 /* desc mask is for rev1.x, we need runtime fixup for >=2.x */
-			descriptor-types-mask = <01010ebf>;
+			descriptor-types-mask = <0x1010ebf>;
 		};
 	};
 

arch/powerpc/boot/dts/mpc832x_mds.dts

@@ -255,9 +255,7 @@ usb@6c0 {
 		enet0: ucc@2200 {
 			device_type = "network";
 			compatible = "ucc_geth";
-			model = "UCC";
 			cell-index = <3>;
-			device-id = <3>;
 			reg = <0x2200 0x200>;
 			interrupts = <34>;
 			interrupt-parent = <&qeic>;
@@ -271,9 +269,7 @@ enet0: ucc@2200 {
 		enet1: ucc@3200 {
 			device_type = "network";
 			compatible = "ucc_geth";
-			model = "UCC";
 			cell-index = <4>;
-			device-id = <4>;
 			reg = <0x3200 0x200>;
 			interrupts = <35>;
 			interrupt-parent = <&qeic>;
@@ -287,8 +283,7 @@ enet1: ucc@3200 {
 		ucc@2400 {
 			device_type = "serial";
 			compatible = "ucc_uart";
-			model = "UCC";
-			device-id = <5>;	/* The UCC number, 1-7*/
+			cell-index = <5>;	/* The UCC number, 1-7*/
 			port-number = <0>;	/* Which ttyQEx device */
 			soft-uart;		/* We need Soft-UART */
 			reg = <0x2400 0x200>;

arch/powerpc/boot/dts/mpc832x_rdb.dts

@@ -208,9 +208,7 @@ spi@500 {
 		enet0: ucc@3000 {
 			device_type = "network";
 			compatible = "ucc_geth";
-			model = "UCC";
 			cell-index = <2>;
-			device-id = <2>;
 			reg = <0x3000 0x200>;
 			interrupts = <33>;
 			interrupt-parent = <&qeic>;
@@ -224,9 +222,7 @@ enet0: ucc@3000 {
 		enet1: ucc@2200 {
 			device_type = "network";
 			compatible = "ucc_geth";
-			model = "UCC";
 			cell-index = <3>;
-			device-id = <3>;
 			reg = <0x2200 0x200>;
 			interrupts = <34>;
 			interrupt-parent = <&qeic>;

arch/powerpc/boot/dts/mpc836x_mds.dts

@@ -257,9 +257,7 @@ usb@6c0 {
 		enet0: ucc@2000 {
 			device_type = "network";
 			compatible = "ucc_geth";
-			model = "UCC";
 			cell-index = <1>;
-			device-id = <1>;
 			reg = <0x2000 0x200>;
 			interrupts = <32>;
 			interrupt-parent = <&qeic>;
@@ -274,9 +272,7 @@ enet0: ucc@2000 {
 		enet1: ucc@3000 {
 			device_type = "network";
 			compatible = "ucc_geth";
-			model = "UCC";
 			cell-index = <2>;
-			device-id = <2>;
 			reg = <0x3000 0x200>;
 			interrupts = <33>;
 			interrupt-parent = <&qeic>;

arch/powerpc/boot/dts/mpc8540ads.dts

 /*
  * MPC8540 ADS Device Tree Source
  *
- * Copyright 2006 Freescale Semiconductor Inc.
+ * Copyright 2006, 2008 Freescale Semiconductor Inc.
  *
  * This program is free software; you can redistribute  it and/or modify it
  * under  the terms of  the GNU General  Public License as published by the
@@ -9,6 +9,7 @@
  * option) any later version.
  */
 
+/dts-v1/;
 
 / {
 	model = "MPC8540ADS";
@@ -31,11 +32,11 @@ cpus {
 
 		PowerPC,8540@0 {
 			device_type = "cpu";
-			reg = <0>;
-			d-cache-line-size = <20>;	// 32 bytes
-			i-cache-line-size = <20>;	// 32 bytes
-			d-cache-size = <8000>;		// L1, 32K
-			i-cache-size = <8000>;		// L1, 32K
+			reg = <0x0>;
+			d-cache-line-size = <32>;	// 32 bytes
+			i-cache-line-size = <32>;	// 32 bytes
+			d-cache-size = <0x8000>;		// L1, 32K
+			i-cache-size = <0x8000>;		// L1, 32K
 			timebase-frequency = <0>;	//  33 MHz, from uboot
 			bus-frequency = <0>;	// 166 MHz
 			clock-frequency = <0>;	// 825 MHz, from uboot
@@ -44,31 +45,31 @@ PowerPC,8540@0 {
 
 	memory {
 		device_type = "memory";
-		reg = <00000000 08000000>;	// 128M at 0x0
+		reg = <0x0 0x8000000>;	// 128M at 0x0
 	};
 
 	soc8540@e0000000 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		device_type = "soc";
-		ranges = <0 e0000000 00100000>;
-		reg = <e0000000 00100000>;	// CCSRBAR 1M
+		ranges = <0x0 0xe0000000 0x100000>;
+		reg = <0xe0000000 0x100000>;	// CCSRBAR 1M
 		bus-frequency = <0>;
 
 		memory-controller@2000 {
 			compatible = "fsl,8540-memory-controller";
-			reg = <2000 1000>;
+			reg = <0x2000 0x1000>;
 			interrupt-parent = <&mpic>;
-			interrupts = <12 2>;
+			interrupts = <18 2>;
 		};
 
 		l2-cache-controller@20000 {
 			compatible = "fsl,8540-l2-cache-controller";
-			reg = <20000 1000>;
-			cache-line-size = <20>;	// 32 bytes
-			cache-size = <40000>;	// L2, 256K
+			reg = <0x20000 0x1000>;
+			cache-line-size = <32>;	// 32 bytes
+			cache-size = <0x40000>;	// L2, 256K
 			interrupt-parent = <&mpic>;
-			interrupts = <10 2>;
+			interrupts = <16 2>;
 		};
 
 		i2c@3000 {
@@ -76,8 +77,8 @@ i2c@3000 {
 			#size-cells = <0>;
 			cell-index = <0>;
 			compatible = "fsl-i2c";
-			reg = <3000 100>;
-			interrupts = <2b 2>;
+			reg = <0x3000 0x100>;
+			interrupts = <43 2>;
 			interrupt-parent = <&mpic>;
 			dfsrr;
 		};
@@ -86,24 +87,24 @@ mdio@24520 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "fsl,gianfar-mdio";
-			reg = <24520 20>;
+			reg = <0x24520 0x20>;
 
 			phy0: ethernet-phy@0 {
 				interrupt-parent = <&mpic>;
 				interrupts = <5 1>;
-				reg = <0>;
+				reg = <0x0>;
 				device_type = "ethernet-phy";
 			};
 			phy1: ethernet-phy@1 {
 				interrupt-parent = <&mpic>;
 				interrupts = <5 1>;
-				reg = <1>;
+				reg = <0x1>;
 				device_type = "ethernet-phy";
 			};
 			phy3: ethernet-phy@3 {
 				interrupt-parent = <&mpic>;
 				interrupts = <7 1>;
-				reg = <3>;
+				reg = <0x3>;
 				device_type = "ethernet-phy";
 			};
 		};
@@ -113,9 +114,9 @@ enet0: ethernet@24000 {
 			device_type = "network";
 			model = "TSEC";
 			compatible = "gianfar";
-			reg = <24000 1000>;
+			reg = <0x24000 0x1000>;
 			local-mac-address = [ 00 00 00 00 00 00 ];
-			interrupts = <1d 2 1e 2 22 2>;
+			interrupts = <29 2 30 2 34 2>;
 			interrupt-parent = <&mpic>;
 			phy-handle = <&phy0>;
 		};
@@ -125,9 +126,9 @@ enet1: ethernet@25000 {
 			device_type = "network";
 			model = "TSEC";
 			compatible = "gianfar";
-			reg = <25000 1000>;
+			reg = <0x25000 0x1000>;
 			local-mac-address = [ 00 00 00 00 00 00 ];
-			interrupts = <23 2 24 2 28 2>;
+			interrupts = <35 2 36 2 40 2>;
 			interrupt-parent = <&mpic>;
 			phy-handle = <&phy1>;
 		};
@@ -137,9 +138,9 @@ enet2: ethernet@26000 {
 			device_type = "network";
 			model = "FEC";
 			compatible = "gianfar";
-			reg = <26000 1000>;
+			reg = <0x26000 0x1000>;
 			local-mac-address = [ 00 00 00 00 00 00 ];
-			interrupts = <29 2>;
+			interrupts = <41 2>;
 			interrupt-parent = <&mpic>;
 			phy-handle = <&phy3>;
 		};
@@ -148,9 +149,9 @@ serial0: serial@4500 {
 			cell-index = <0>;
 			device_type = "serial";
 			compatible = "ns16550";
-			reg = <4500 100>; 	// reg base, size
+			reg = <0x4500 0x100>; 	// reg base, size
 			clock-frequency = <0>; 	// should we fill in in uboot?
-			interrupts = <2a 2>;
+			interrupts = <42 2>;
 			interrupt-parent = <&mpic>;
 		};
 
@@ -158,9 +159,9 @@ serial1: serial@4600 {
 			cell-index = <1>;
 			device_type = "serial";
 			compatible = "ns16550";
-			reg = <4600 100>;	// reg base, size
+			reg = <0x4600 0x100>;	// reg base, size
 			clock-frequency = <0>; 	// should we fill in in uboot?
-			interrupts = <2a 2>;
+			interrupts = <42 2>;
 			interrupt-parent = <&mpic>;
 		};
 		mpic: pic@40000 {
@@ -168,7 +169,7 @@ mpic: pic@40000 {
 			interrupt-controller;
 			#address-cells = <0>;
 			#interrupt-cells = <2>;
-			reg = <40000 40000>;
+			reg = <0x40000 0x40000>;
 			compatible = "chrp,open-pic";
 			device_type = "open-pic";
 			big-endian;
@@ -177,90 +178,90 @@ mpic: pic@40000 {
 
 	pci0: pci@e0008000 {
 		cell-index = <0>;
-		interrupt-map-mask = <f800 0 0 7>;
+		interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
 		interrupt-map = <
 
 			/* IDSEL 0x02 */
-			1000 0 0 1 &mpic 1 1
-			1000 0 0 2 &mpic 2 1
-			1000 0 0 3 &mpic 3 1
-			1000 0 0 4 &mpic 4 1
+			0x1000 0x0 0x0 0x1 &mpic 0x1 0x1
+			0x1000 0x0 0x0 0x2 &mpic 0x2 0x1
+			0x1000 0x0 0x0 0x3 &mpic 0x3 0x1
+			0x1000 0x0 0x0 0x4 &mpic 0x4 0x1
 
 			/* IDSEL 0x03 */
-			1800 0 0 1 &mpic 4 1
-			1800 0 0 2 &mpic 1 1
-			1800 0 0 3 &mpic 2 1
-			1800 0 0 4 &mpic 3 1
+			0x1800 0x0 0x0 0x1 &mpic 0x4 0x1
+			0x1800 0x0 0x0 0x2 &mpic 0x1 0x1
+			0x1800 0x0 0x0 0x3 &mpic 0x2 0x1
+			0x1800 0x0 0x0 0x4 &mpic 0x3 0x1
 
 			/* IDSEL 0x04 */
-			2000 0 0 1 &mpic 3 1
-			2000 0 0 2 &mpic 4 1
-			2000 0 0 3 &mpic 1 1
-			2000 0 0 4 &mpic 2 1
+			0x2000 0x0 0x0 0x1 &mpic 0x3 0x1
+			0x2000 0x0 0x0 0x2 &mpic 0x4 0x1
+			0x2000 0x0 0x0 0x3 &mpic 0x1 0x1
+			0x2000 0x0 0x0 0x4 &mpic 0x2 0x1
 
 			/* IDSEL 0x05 */
-			2800 0 0 1 &mpic 2 1
-			2800 0 0 2 &mpic 3 1
-			2800 0 0 3 &mpic 4 1
-			2800 0 0 4 &mpic 1 1
+			0x2800 0x0 0x0 0x1 &mpic 0x2 0x1
+			0x2800 0x0 0x0 0x2 &mpic 0x3 0x1
+			0x2800 0x0 0x0 0x3 &mpic 0x4 0x1
+			0x2800 0x0 0x0 0x4 &mpic 0x1 0x1
 
 			/* IDSEL 0x0c */
-			6000 0 0 1 &mpic 1 1
-			6000 0 0 2 &mpic 2 1
-			6000 0 0 3 &mpic 3 1
-			6000 0 0 4 &mpic 4 1
+			0x6000 0x0 0x0 0x1 &mpic 0x1 0x1
+			0x6000 0x0 0x0 0x2 &mpic 0x2 0x1
+			0x6000 0x0 0x0 0x3 &mpic 0x3 0x1
+			0x6000 0x0 0x0 0x4 &mpic 0x4 0x1
 
 			/* IDSEL 0x0d */
-			6800 0 0 1 &mpic 4 1
-			6800 0 0 2 &mpic 1 1
-			6800 0 0 3 &mpic 2 1
-			6800 0 0 4 &mpic 3 1
+			0x6800 0x0 0x0 0x1 &mpic 0x4 0x1
+			0x6800 0x0 0x0 0x2 &mpic 0x1 0x1
+			0x6800 0x0 0x0 0x3 &mpic 0x2 0x1
+			0x6800 0x0 0x0 0x4 &mpic 0x3 0x1
 
 			/* IDSEL 0x0e */
-			7000 0 0 1 &mpic 3 1
-			7000 0 0 2 &mpic 4 1
-			7000 0 0 3 &mpic 1 1
-			7000 0 0 4 &mpic 2 1
+			0x7000 0x0 0x0 0x1 &mpic 0x3 0x1
+			0x7000 0x0 0x0 0x2 &mpic 0x4 0x1
+			0x7000 0x0 0x0 0x3 &mpic 0x1 0x1
+			0x7000 0x0 0x0 0x4 &mpic 0x2 0x1
 
 			/* IDSEL 0x0f */
-			7800 0 0 1 &mpic 2 1
-			7800 0 0 2 &mpic 3 1
-			7800 0 0 3 &mpic 4 1
-			7800 0 0 4 &mpic 1 1
+			0x7800 0x0 0x0 0x1 &mpic 0x2 0x1
+			0x7800 0x0 0x0 0x2 &mpic 0x3 0x1
+			0x7800 0x0 0x0 0x3 &mpic 0x4 0x1
+			0x7800 0x0 0x0 0x4 &mpic 0x1 0x1
 
 			/* IDSEL 0x12 */
-			9000 0 0 1 &mpic 1 1
-			9000 0 0 2 &mpic 2 1
-			9000 0 0 3 &mpic 3 1
-			9000 0 0 4 &mpic 4 1
+			0x9000 0x0 0x0 0x1 &mpic 0x1 0x1
+			0x9000 0x0 0x0 0x2 &mpic 0x2 0x1
+			0x9000 0x0 0x0 0x3 &mpic 0x3 0x1
+			0x9000 0x0 0x0 0x4 &mpic 0x4 0x1
 
 			/* IDSEL 0x13 */
-			9800 0 0 1 &mpic 4 1
-			9800 0 0 2 &mpic 1 1
-			9800 0 0 3 &mpic 2 1
-			9800 0 0 4 &mpic 3 1
+			0x9800 0x0 0x0 0x1 &mpic 0x4 0x1
+			0x9800 0x0 0x0 0x2 &mpic 0x1 0x1
+			0x9800 0x0 0x0 0x3 &mpic 0x2 0x1
+			0x9800 0x0 0x0 0x4 &mpic 0x3 0x1
 
 			/* IDSEL 0x14 */
-			a000 0 0 1 &mpic 3 1
-			a000 0 0 2 &mpic 4 1
-			a000 0 0 3 &mpic 1 1
-			a000 0 0 4 &mpic 2 1
+			0xa000 0x0 0x0 0x1 &mpic 0x3 0x1
+			0xa000 0x0 0x0 0x2 &mpic 0x4 0x1
+			0xa000 0x0 0x0 0x3 &mpic 0x1 0x1
+			0xa000 0x0 0x0 0x4 &mpic 0x2 0x1
 
 			/* IDSEL 0x15 */
-			a800 0 0 1 &mpic 2 1
-			a800 0 0 2 &mpic 3 1
-			a800 0 0 3 &mpic 4 1
-			a800 0 0 4 &mpic 1 1>;
+			0xa800 0x0 0x0 0x1 &mpic 0x2 0x1
+			0xa800 0x0 0x0 0x2 &mpic 0x3 0x1
+			0xa800 0x0 0x0 0x3 &mpic 0x4 0x1
+			0xa800 0x0 0x0 0x4 &mpic 0x1 0x1>;
 		interrupt-parent = <&mpic>;
-		interrupts = <18 2>;
+		interrupts = <24 2>;
 		bus-range = <0 0>;
-		ranges = <02000000 0 80000000 80000000 0 20000000
-			  01000000 0 00000000 e2000000 0 00100000>;
-		clock-frequency = <3f940aa>;
+		ranges = <0x2000000 0x0 0x80000000 0x80000000 0x0 0x20000000
+			  0x1000000 0x0 0x0 0xe2000000 0x0 0x100000>;
+		clock-frequency = <66666666>;
 		#interrupt-cells = <1>;
 		#size-cells = <2>;
 		#address-cells = <3>;
-		reg = <e0008000 1000>;
+		reg = <0xe0008000 0x1000>;
 		compatible = "fsl,mpc8540-pcix", "fsl,mpc8540-pci";
 		device_type = "pci";
 	};

arch/powerpc/boot/dts/mpc8541cds.dts

 /*
  * MPC8541 CDS Device Tree Source
  *
- * Copyright 2006 Freescale Semiconductor Inc.
+ * Copyright 2006, 2008 Freescale Semiconductor Inc.
  *
  * This program is free software; you can redistribute  it and/or modify it
  * under  the terms of  the GNU General  Public License as published by the
@@ -9,6 +9,7 @@
  * option) any later version.
  */
 
+/dts-v1/;
 
 / {
 	model = "MPC8541CDS";
@@ -31,11 +32,11 @@ cpus {
 
 		PowerPC,8541@0 {
 			device_type = "cpu";
-			reg = <0>;
-			d-cache-line-size = <20>;	// 32 bytes
-			i-cache-line-size = <20>;	// 32 bytes
-			d-cache-size = <8000>;		// L1, 32K
-			i-cache-size = <8000>;		// L1, 32K
+			reg = <0x0>;
+			d-cache-line-size = <32>;	// 32 bytes
+			i-cache-line-size = <32>;	// 32 bytes
+			d-cache-size = <0x8000>;		// L1, 32K
+			i-cache-size = <0x8000>;		// L1, 32K
 			timebase-frequency = <0>;	//  33 MHz, from uboot
 			bus-frequency = <0>;	// 166 MHz
 			clock-frequency = <0>;	// 825 MHz, from uboot
@@ -44,31 +45,31 @@ PowerPC,8541@0 {
 
 	memory {
 		device_type = "memory";
-		reg = <00000000 08000000>;	// 128M at 0x0
+		reg = <0x0 0x8000000>;	// 128M at 0x0
 	};
 
 	soc8541@e0000000 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		device_type = "soc";
-		ranges = <0 e0000000 00100000>;
-		reg = <e0000000 00001000>;	// CCSRBAR 1M
+		ranges = <0x0 0xe0000000 0x100000>;
+		reg = <0xe0000000 0x1000>;	// CCSRBAR 1M
 		bus-frequency = <0>;
 
 		memory-controller@2000 {
 			compatible = "fsl,8541-memory-controller";
-			reg = <2000 1000>;
+			reg = <0x2000 0x1000>;
 			interrupt-parent = <&mpic>;
-			interrupts = <12 2>;
+			interrupts = <18 2>;
 		};
 
 		l2-cache-controller@20000 {
 			compatible = "fsl,8541-l2-cache-controller";
-			reg = <20000 1000>;
-			cache-line-size = <20>;	// 32 bytes
-			cache-size = <40000>;	// L2, 256K
+			reg = <0x20000 0x1000>;
+			cache-line-size = <32>;	// 32 bytes
+			cache-size = <0x40000>;	// L2, 256K
 			interrupt-parent = <&mpic>;
-			interrupts = <10 2>;
+			interrupts = <16 2>;
 		};
 
 		i2c@3000 {
@@ -76,8 +77,8 @@ i2c@3000 {
 			#size-cells = <0>;
 			cell-index = <0>;
 			compatible = "fsl-i2c";
-			reg = <3000 100>;
-			interrupts = <2b 2>;
+			reg = <0x3000 0x100>;
+			interrupts = <43 2>;
 			interrupt-parent = <&mpic>;
 			dfsrr;
 		};
@@ -86,18 +87,18 @@ mdio@24520 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "fsl,gianfar-mdio";
-			reg = <24520 20>;
+			reg = <0x24520 0x20>;
 
 			phy0: ethernet-phy@0 {
 				interrupt-parent = <&mpic>;
 				interrupts = <5 1>;
-				reg = <0>;
+				reg = <0x0>;
 				device_type = "ethernet-phy";
 			};
 			phy1: ethernet-phy@1 {
 				interrupt-parent = <&mpic>;
 				interrupts = <5 1>;
-				reg = <1>;
+				reg = <0x1>;
 				device_type = "ethernet-phy";
 			};
 		};
@@ -107,9 +108,9 @@ enet0: ethernet@24000 {
 			device_type = "network";
 			model = "TSEC";
 			compatible = "gianfar";
-			reg = <24000 1000>;
+			reg = <0x24000 0x1000>;
 			local-mac-address = [ 00 00 00 00 00 00 ];
-			interrupts = <1d 2 1e 2 22 2>;
+			interrupts = <29 2 30 2 34 2>;
 			interrupt-parent = <&mpic>;
 			phy-handle = <&phy0>;
 		};
@@ -119,9 +120,9 @@ enet1: ethernet@25000 {
 			device_type = "network";
 			model = "TSEC";
 			compatible = "gianfar";
-			reg = <25000 1000>;
+			reg = <0x25000 0x1000>;
 			local-mac-address = [ 00 00 00 00 00 00 ];
-			interrupts = <23 2 24 2 28 2>;
+			interrupts = <35 2 36 2 40 2>;
 			interrupt-parent = <&mpic>;
 			phy-handle = <&phy1>;
 		};
@@ -130,9 +131,9 @@ serial0: serial@4500 {
 			cell-index = <0>;
 			device_type = "serial";
 			compatible = "ns16550";
-			reg = <4500 100>; 	// reg base, size
+			reg = <0x4500 0x100>; 	// reg base, size
 			clock-frequency = <0>; 	// should we fill in in uboot?
-			interrupts = <2a 2>;
+			interrupts = <42 2>;
 			interrupt-parent = <&mpic>;
 		};
 
@@ -140,9 +141,9 @@ serial1: serial@4600 {
 			cell-index = <1>;
 			device_type = "serial";
 			compatible = "ns16550";
-			reg = <4600 100>;	// reg base, size
+			reg = <0x4600 0x100>;	// reg base, size
 			clock-frequency = <0>; 	// should we fill in in uboot?
-			interrupts = <2a 2>;
+			interrupts = <42 2>;
 			interrupt-parent = <&mpic>;
 		};
 
@@ -151,7 +152,7 @@ mpic: pic@40000 {
 			interrupt-controller;
 			#address-cells = <0>;
 			#interrupt-cells = <2>;
-			reg = <40000 40000>;
+			reg = <0x40000 0x40000>;
 			compatible = "chrp,open-pic";
 			device_type = "open-pic";
                         big-endian;
@@ -161,17 +162,17 @@ cpm@919c0 {
 			#address-cells = <1>;
 			#size-cells = <1>;
 			compatible = "fsl,mpc8541-cpm", "fsl,cpm2";
-			reg = <919c0 30>;
+			reg = <0x919c0 0x30>;
 			ranges;
 
 			muram@80000 {
 				#address-cells = <1>;
 				#size-cells = <1>;
-				ranges = <0 80000 10000>;
+				ranges = <0x0 0x80000 0x10000>;
 
 				data@0 {
 					compatible = "fsl,cpm-muram-data";
-					reg = <0 2000 9000 1000>;
+					reg = <0x0 0x2000 0x9000 0x1000>;
 				};
 			};
 
@@ -179,16 +180,16 @@ brg@919f0 {
 				compatible = "fsl,mpc8541-brg",
 				             "fsl,cpm2-brg",
 				             "fsl,cpm-brg";
-				reg = <919f0 10 915f0 10>;
+				reg = <0x919f0 0x10 0x915f0 0x10>;
 			};
 
 			cpmpic: pic@90c00 {
 				interrupt-controller;
 				#address-cells = <0>;
 				#interrupt-cells = <2>;
-				interrupts = <2e 2>;
+				interrupts = <46 2>;
 				interrupt-parent = <&mpic>;
-				reg = <90c00 80>;
+				reg = <0x90c00 0x80>;
 				compatible = "fsl,mpc8541-cpm-pic", "fsl,cpm2-pic";
 			};
 		};
@@ -196,68 +197,68 @@ cpmpic: pic@90c00 {
 
 	pci0: pci@e0008000 {
 		cell-index = <0>;
-		interrupt-map-mask = <1f800 0 0 7>;
+		interrupt-map-mask = <0x1f800 0x0 0x0 0x7>;
 		interrupt-map = <
 
 			/* IDSEL 0x10 */
-			08000 0 0 1 &mpic 0 1
-			08000 0 0 2 &mpic 1 1
-			08000 0 0 3 &mpic 2 1
-			08000 0 0 4 &mpic 3 1
+			0x8000 0x0 0x0 0x1 &mpic 0x0 0x1
+			0x8000 0x0 0x0 0x2 &mpic 0x1 0x1
+			0x8000 0x0 0x0 0x3 &mpic 0x2 0x1
+			0x8000 0x0 0x0 0x4 &mpic 0x3 0x1
 
 			/* IDSEL 0x11 */
-			08800 0 0 1 &mpic 0 1
-			08800 0 0 2 &mpic 1 1
-			08800 0 0 3 &mpic 2 1
-			08800 0 0 4 &mpic 3 1
+			0x8800 0x0 0x0 0x1 &mpic 0x0 0x1
+			0x8800 0x0 0x0 0x2 &mpic 0x1 0x1
+			0x8800 0x0 0x0 0x3 &mpic 0x2 0x1
+			0x8800 0x0 0x0 0x4 &mpic 0x3 0x1
 
 			/* IDSEL 0x12 (Slot 1) */
-			09000 0 0 1 &mpic 0 1
-			09000 0 0 2 &mpic 1 1
-			09000 0 0 3 &mpic 2 1
-			09000 0 0 4 &mpic 3 1
+			0x9000 0x0 0x0 0x1 &mpic 0x0 0x1
+			0x9000 0x0 0x0 0x2 &mpic 0x1 0x1
+			0x9000 0x0 0x0 0x3 &mpic 0x2 0x1
+			0x9000 0x0 0x0 0x4 &mpic 0x3 0x1
 
 			/* IDSEL 0x13 (Slot 2) */
-			09800 0 0 1 &mpic 1 1
-			09800 0 0 2 &mpic 2 1
-			09800 0 0 3 &mpic 3 1
-			09800 0 0 4 &mpic 0 1
+			0x9800 0x0 0x0 0x1 &mpic 0x1 0x1
+			0x9800 0x0 0x0 0x2 &mpic 0x2 0x1
+			0x9800 0x0 0x0 0x3 &mpic 0x3 0x1
+			0x9800 0x0 0x0 0x4 &mpic 0x0 0x1
 
 			/* IDSEL 0x14 (Slot 3) */
-			0a000 0 0 1 &mpic 2 1
-			0a000 0 0 2 &mpic 3 1
-			0a000 0 0 3 &mpic 0 1
-			0a000 0 0 4 &mpic 1 1
+			0xa000 0x0 0x0 0x1 &mpic 0x2 0x1
+			0xa000 0x0 0x0 0x2 &mpic 0x3 0x1
+			0xa000 0x0 0x0 0x3 &mpic 0x0 0x1
+			0xa000 0x0 0x0 0x4 &mpic 0x1 0x1
 
 			/* IDSEL 0x15 (Slot 4) */
-			0a800 0 0 1 &mpic 3 1
-			0a800 0 0 2 &mpic 0 1
-			0a800 0 0 3 &mpic 1 1
-			0a800 0 0 4 &mpic 2 1
+			0xa800 0x0 0x0 0x1 &mpic 0x3 0x1
+			0xa800 0x0 0x0 0x2 &mpic 0x0 0x1
+			0xa800 0x0 0x0 0x3 &mpic 0x1 0x1
+			0xa800 0x0 0x0 0x4 &mpic 0x2 0x1
 
 			/* Bus 1 (Tundra Bridge) */
 			/* IDSEL 0x12 (ISA bridge) */
-			19000 0 0 1 &mpic 0 1
-			19000 0 0 2 &mpic 1 1
-			19000 0 0 3 &mpic 2 1
-			19000 0 0 4 &mpic 3 1>;
+			0x19000 0x0 0x0 0x1 &mpic 0x0 0x1
+			0x19000 0x0 0x0 0x2 &mpic 0x1 0x1
+			0x19000 0x0 0x0 0x3 &mpic 0x2 0x1
+			0x19000 0x0 0x0 0x4 &mpic 0x3 0x1>;
 		interrupt-parent = <&mpic>;
-		interrupts = <18 2>;
+		interrupts = <24 2>;
 		bus-range = <0 0>;
-		ranges = <02000000 0 80000000 80000000 0 20000000
-			  01000000 0 00000000 e2000000 0 00100000>;
-		clock-frequency = <3f940aa>;
+		ranges = <0x2000000 0x0 0x80000000 0x80000000 0x0 0x20000000
+			  0x1000000 0x0 0x0 0xe2000000 0x0 0x100000>;
+		clock-frequency = <66666666>;
 		#interrupt-cells = <1>;
 		#size-cells = <2>;
 		#address-cells = <3>;
-		reg = <e0008000 1000>;
+		reg = <0xe0008000 0x1000>;
 		compatible = "fsl,mpc8540-pci";
 		device_type = "pci";
 
 		i8259@19000 {
 			interrupt-controller;
 			device_type = "interrupt-controller";
-			reg = <19000 0 0 0 1>;
+			reg = <0x19000 0x0 0x0 0x0 0x1>;
 			#address-cells = <0>;
 			#interrupt-cells = <2>;
 			compatible = "chrp,iic";
@@ -268,24 +269,24 @@ i8259@19000 {
 
 	pci1: pci@e0009000 {
 		cell-index = <1>;
-		interrupt-map-mask = <f800 0 0 7>;
+		interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
 		interrupt-map = <
 
 			/* IDSEL 0x15 */
-			a800 0 0 1 &mpic b 1
-			a800 0 0 2 &mpic b 1
-			a800 0 0 3 &mpic b 1
-			a800 0 0 4 &mpic b 1>;
+			0xa800 0x0 0x0 0x1 &mpic 0xb 0x1
+			0xa800 0x0 0x0 0x2 &mpic 0xb 0x1
+			0xa800 0x0 0x0 0x3 &mpic 0xb 0x1
+			0xa800 0x0 0x0 0x4 &mpic 0xb 0x1>;
 		interrupt-parent = <&mpic>;
-		interrupts = <19 2>;
+		interrupts = <25 2>;
 		bus-range = <0 0>;
-		ranges = <02000000 0 a0000000 a0000000 0 20000000
-			  01000000 0 00000000 e3000000 0 00100000>;
-		clock-frequency = <3f940aa>;
+		ranges = <0x2000000 0x0 0xa0000000 0xa0000000 0x0 0x20000000
+			  0x1000000 0x0 0x0 0xe3000000 0x0 0x100000>;
+		clock-frequency = <66666666>;
 		#interrupt-cells = <1>;
 		#size-cells = <2>;
 		#address-cells = <3>;
-		reg = <e0009000 1000>;
+		reg = <0xe0009000 0x1000>;
 		compatible = "fsl,mpc8540-pci";
 		device_type = "pci";
 	};

arch/powerpc/boot/dts/mpc8555cds.dts

 /*
  * MPC8555 CDS Device Tree Source
  *
- * Copyright 2006 Freescale Semiconductor Inc.
+ * Copyright 2006, 2008 Freescale Semiconductor Inc.
  *
  * This program is free software; you can redistribute  it and/or modify it
  * under  the terms of  the GNU General  Public License as published by the
@@ -9,6 +9,7 @@
  * option) any later version.
  */
 
+/dts-v1/;
 
 / {
 	model = "MPC8555CDS";
@@ -31,11 +32,11 @@ cpus {
 
 		PowerPC,8555@0 {
 			device_type = "cpu";
-			reg = <0>;
-			d-cache-line-size = <20>;	// 32 bytes
-			i-cache-line-size = <20>;	// 32 bytes
-			d-cache-size = <8000>;		// L1, 32K
-			i-cache-size = <8000>;		// L1, 32K
+			reg = <0x0>;
+			d-cache-line-size = <32>;	// 32 bytes
+			i-cache-line-size = <32>;	// 32 bytes
+			d-cache-size = <0x8000>;		// L1, 32K
+			i-cache-size = <0x8000>;		// L1, 32K
 			timebase-frequency = <0>;	//  33 MHz, from uboot
 			bus-frequency = <0>;	// 166 MHz
 			clock-frequency = <0>;	// 825 MHz, from uboot
@@ -44,31 +45,31 @@ PowerPC,8555@0 {
 
 	memory {
 		device_type = "memory";
-		reg = <00000000 08000000>;	// 128M at 0x0
+		reg = <0x0 0x8000000>;	// 128M at 0x0
 	};
 
 	soc8555@e0000000 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		device_type = "soc";
-		ranges = <0 e0000000 00100000>;
-		reg = <e0000000 00001000>;	// CCSRBAR 1M
+		ranges = <0x0 0xe0000000 0x100000>;
+		reg = <0xe0000000 0x1000>;	// CCSRBAR 1M
 		bus-frequency = <0>;
 
 		memory-controller@2000 {
 			compatible = "fsl,8555-memory-controller";
-			reg = <2000 1000>;
+			reg = <0x2000 0x1000>;
 			interrupt-parent = <&mpic>;
-			interrupts = <12 2>;
+			interrupts = <18 2>;
 		};
 
 		l2-cache-controller@20000 {
 			compatible = "fsl,8555-l2-cache-controller";
-			reg = <20000 1000>;
-			cache-line-size = <20>;	// 32 bytes
-			cache-size = <40000>;	// L2, 256K
+			reg = <0x20000 0x1000>;
+			cache-line-size = <32>;	// 32 bytes
+			cache-size = <0x40000>;	// L2, 256K
 			interrupt-parent = <&mpic>;
-			interrupts = <10 2>;
+			interrupts = <16 2>;
 		};
 
 		i2c@3000 {
@@ -76,8 +77,8 @@ i2c@3000 {
 			#size-cells = <0>;
 			cell-index = <0>;
 			compatible = "fsl-i2c";
-			reg = <3000 100>;
-			interrupts = <2b 2>;
+			reg = <0x3000 0x100>;
+			interrupts = <43 2>;
 			interrupt-parent = <&mpic>;
 			dfsrr;
 		};
@@ -86,18 +87,18 @@ mdio@24520 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "fsl,gianfar-mdio";
-			reg = <24520 20>;
+			reg = <0x24520 0x20>;
 
 			phy0: ethernet-phy@0 {
 				interrupt-parent = <&mpic>;
 				interrupts = <5 1>;
-				reg = <0>;
+				reg = <0x0>;
 				device_type = "ethernet-phy";
 			};
 			phy1: ethernet-phy@1 {
 				interrupt-parent = <&mpic>;
 				interrupts = <5 1>;
-				reg = <1>;
+				reg = <0x1>;
 				device_type = "ethernet-phy";
 			};
 		};
@@ -107,9 +108,9 @@ enet0: ethernet@24000 {
 			device_type = "network";
 			model = "TSEC";
 			compatible = "gianfar";
-			reg = <24000 1000>;
+			reg = <0x24000 0x1000>;
 			local-mac-address = [ 00 00 00 00 00 00 ];
-			interrupts = <1d 2 1e 2 22 2>;
+			interrupts = <29 2 30 2 34 2>;
 			interrupt-parent = <&mpic>;
 			phy-handle = <&phy0>;
 		};
@@ -119,9 +120,9 @@ enet1: ethernet@25000 {
 			device_type = "network";
 			model = "TSEC";
 			compatible = "gianfar";
-			reg = <25000 1000>;
+			reg = <0x25000 0x1000>;
 			local-mac-address = [ 00 00 00 00 00 00 ];
-			interrupts = <23 2 24 2 28 2>;
+			interrupts = <35 2 36 2 40 2>;
 			interrupt-parent = <&mpic>;
 			phy-handle = <&phy1>;
 		};
@@ -130,9 +131,9 @@ serial0: serial@4500 {
 			cell-index = <0>;
 			device_type = "serial";
 			compatible = "ns16550";
-			reg = <4500 100>; 	// reg base, size
+			reg = <0x4500 0x100>; 	// reg base, size
 			clock-frequency = <0>; 	// should we fill in in uboot?
-			interrupts = <2a 2>;
+			interrupts = <42 2>;
 			interrupt-parent = <&mpic>;
 		};
 
@@ -140,9 +141,9 @@ serial1: serial@4600 {
 			cell-index = <1>;
 			device_type = "serial";
 			compatible = "ns16550";
-			reg = <4600 100>;	// reg base, size
+			reg = <0x4600 0x100>;	// reg base, size
 			clock-frequency = <0>; 	// should we fill in in uboot?
-			interrupts = <2a 2>;
+			interrupts = <42 2>;
 			interrupt-parent = <&mpic>;
 		};
 
@@ -151,7 +152,7 @@ mpic: pic@40000 {
 			interrupt-controller;
 			#address-cells = <0>;
 			#interrupt-cells = <2>;
-			reg = <40000 40000>;
+			reg = <0x40000 0x40000>;
 			compatible = "chrp,open-pic";
 			device_type = "open-pic";
                         big-endian;
@@ -161,17 +162,17 @@ cpm@919c0 {
 			#address-cells = <1>;
 			#size-cells = <1>;
 			compatible = "fsl,mpc8555-cpm", "fsl,cpm2";
-			reg = <919c0 30>;
+			reg = <0x919c0 0x30>;
 			ranges;
 
 			muram@80000 {
 				#address-cells = <1>;
 				#size-cells = <1>;
-				ranges = <0 80000 10000>;
+				ranges = <0x0 0x80000 0x10000>;
 
 				data@0 {
 					compatible = "fsl,cpm-muram-data";
-					reg = <0 2000 9000 1000>;
+					reg = <0x0 0x2000 0x9000 0x1000>;
 				};
 			};
 
@@ -179,16 +180,16 @@ brg@919f0 {
 				compatible = "fsl,mpc8555-brg",
 				             "fsl,cpm2-brg",
 				             "fsl,cpm-brg";
-				reg = <919f0 10 915f0 10>;
+				reg = <0x919f0 0x10 0x915f0 0x10>;
 			};
 
 			cpmpic: pic@90c00 {
 				interrupt-controller;
 				#address-cells = <0>;
 				#interrupt-cells = <2>;
-				interrupts = <2e 2>;
+				interrupts = <46 2>;
 				interrupt-parent = <&mpic>;
-				reg = <90c00 80>;
+				reg = <0x90c00 0x80>;
 				compatible = "fsl,mpc8555-cpm-pic", "fsl,cpm2-pic";
 			};
 		};
@@ -196,68 +197,68 @@ cpmpic: pic@90c00 {
 
 	pci0: pci@e0008000 {
 		cell-index = <0>;
-		interrupt-map-mask = <1f800 0 0 7>;
+		interrupt-map-mask = <0x1f800 0x0 0x0 0x7>;
 		interrupt-map = <
 
 			/* IDSEL 0x10 */
-			08000 0 0 1 &mpic 0 1
-			08000 0 0 2 &mpic 1 1
-			08000 0 0 3 &mpic 2 1
-			08000 0 0 4 &mpic 3 1
+			0x8000 0x0 0x0 0x1 &mpic 0x0 0x1
+			0x8000 0x0 0x0 0x2 &mpic 0x1 0x1
+			0x8000 0x0 0x0 0x3 &mpic 0x2 0x1
+			0x8000 0x0 0x0 0x4 &mpic 0x3 0x1
 
 			/* IDSEL 0x11 */
-			08800 0 0 1 &mpic 0 1
-			08800 0 0 2 &mpic 1 1
-			08800 0 0 3 &mpic 2 1
-			08800 0 0 4 &mpic 3 1
+			0x8800 0x0 0x0 0x1 &mpic 0x0 0x1
+			0x8800 0x0 0x0 0x2 &mpic 0x1 0x1
+			0x8800 0x0 0x0 0x3 &mpic 0x2 0x1
+			0x8800 0x0 0x0 0x4 &mpic 0x3 0x1
 
 			/* IDSEL 0x12 (Slot 1) */
-			09000 0 0 1 &mpic 0 1
-			09000 0 0 2 &mpic 1 1
-			09000 0 0 3 &mpic 2 1
-			09000 0 0 4 &mpic 3 1
+			0x9000 0x0 0x0 0x1 &mpic 0x0 0x1
+			0x9000 0x0 0x0 0x2 &mpic 0x1 0x1
+			0x9000 0x0 0x0 0x3 &mpic 0x2 0x1
+			0x9000 0x0 0x0 0x4 &mpic 0x3 0x1
 
 			/* IDSEL 0x13 (Slot 2) */
-			09800 0 0 1 &mpic 1 1
-			09800 0 0 2 &mpic 2 1
-			09800 0 0 3 &mpic 3 1
-			09800 0 0 4 &mpic 0 1
+			0x9800 0x0 0x0 0x1 &mpic 0x1 0x1
+			0x9800 0x0 0x0 0x2 &mpic 0x2 0x1
+			0x9800 0x0 0x0 0x3 &mpic 0x3 0x1
+			0x9800 0x0 0x0 0x4 &mpic 0x0 0x1
 
 			/* IDSEL 0x14 (Slot 3) */
-			0a000 0 0 1 &mpic 2 1
-			0a000 0 0 2 &mpic 3 1
-			0a000 0 0 3 &mpic 0 1
-			0a000 0 0 4 &mpic 1 1
+			0xa000 0x0 0x0 0x1 &mpic 0x2 0x1
+			0xa000 0x0 0x0 0x2 &mpic 0x3 0x1
+			0xa000 0x0 0x0 0x3 &mpic 0x0 0x1
+			0xa000 0x0 0x0 0x4 &mpic 0x1 0x1
 
 			/* IDSEL 0x15 (Slot 4) */
-			0a800 0 0 1 &mpic 3 1
-			0a800 0 0 2 &mpic 0 1
-			0a800 0 0 3 &mpic 1 1
-			0a800 0 0 4 &mpic 2 1
+			0xa800 0x0 0x0 0x1 &mpic 0x3 0x1
+			0xa800 0x0 0x0 0x2 &mpic 0x0 0x1
+			0xa800 0x0 0x0 0x3 &mpic 0x1 0x1
+			0xa800 0x0 0x0 0x4 &mpic 0x2 0x1
 
 			/* Bus 1 (Tundra Bridge) */
 			/* IDSEL 0x12 (ISA bridge) */
-			19000 0 0 1 &mpic 0 1
-			19000 0 0 2 &mpic 1 1
-			19000 0 0 3 &mpic 2 1
-			19000 0 0 4 &mpic 3 1>;
+			0x19000 0x0 0x0 0x1 &mpic 0x0 0x1
+			0x19000 0x0 0x0 0x2 &mpic 0x1 0x1
+			0x19000 0x0 0x0 0x3 &mpic 0x2 0x1
+			0x19000 0x0 0x0 0x4 &mpic 0x3 0x1>;
 		interrupt-parent = <&mpic>;
-		interrupts = <18 2>;
+		interrupts = <24 2>;
 		bus-range = <0 0>;
-		ranges = <02000000 0 80000000 80000000 0 20000000
-			  01000000 0 00000000 e2000000 0 00100000>;
-		clock-frequency = <3f940aa>;
+		ranges = <0x2000000 0x0 0x80000000 0x80000000 0x0 0x20000000
+			  0x1000000 0x0 0x0 0xe2000000 0x0 0x100000>;
+		clock-frequency = <66666666>;
 		#interrupt-cells = <1>;
 		#size-cells = <2>;
 		#address-cells = <3>;
-		reg = <e0008000 1000>;
+		reg = <0xe0008000 0x1000>;
 		compatible = "fsl,mpc8540-pci";
 		device_type = "pci";
 
 		i8259@19000 {
 			interrupt-controller;
 			device_type = "interrupt-controller";
-			reg = <19000 0 0 0 1>;
+			reg = <0x19000 0x0 0x0 0x0 0x1>;
 			#address-cells = <0>;
 			#interrupt-cells = <2>;
 			compatible = "chrp,iic";
@@ -268,24 +269,24 @@ i8259@19000 {
 
 	pci1: pci@e0009000 {
 		cell-index = <1>;
-		interrupt-map-mask = <f800 0 0 7>;
+		interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
 		interrupt-map = <
 
 			/* IDSEL 0x15 */
-			a800 0 0 1 &mpic b 1
-			a800 0 0 2 &mpic b 1
-			a800 0 0 3 &mpic b 1
-			a800 0 0 4 &mpic b 1>;
+			0xa800 0x0 0x0 0x1 &mpic 0xb 0x1
+			0xa800 0x0 0x0 0x2 &mpic 0xb 0x1
+			0xa800 0x0 0x0 0x3 &mpic 0xb 0x1
+			0xa800 0x0 0x0 0x4 &mpic 0xb 0x1>;
 		interrupt-parent = <&mpic>;
-		interrupts = <19 2>;
+		interrupts = <25 2>;
 		bus-range = <0 0>;
-		ranges = <02000000 0 a0000000 a0000000 0 20000000
-			  01000000 0 00000000 e3000000 0 00100000>;
-		clock-frequency = <3f940aa>;
+		ranges = <0x2000000 0x0 0xa0000000 0xa0000000 0x0 0x20000000
+			  0x1000000 0x0 0x0 0xe3000000 0x0 0x100000>;
+		clock-frequency = <66666666>;
 		#interrupt-cells = <1>;
 		#size-cells = <2>;
 		#address-cells = <3>;
-		reg = <e0009000 1000>;
+		reg = <0xe0009000 0x1000>;
 		compatible = "fsl,mpc8540-pci";
 		device_type = "pci";
 	};

arch/powerpc/boot/ops.h

@@ -95,6 +95,7 @@ int dt_xlate_reg(void *node, int res, unsigned long *addr, unsigned long *size);
 int dt_xlate_addr(void *node, u32 *buf, int buflen, unsigned long *xlated_addr);
 int dt_is_compatible(void *node, const char *compat);
 void dt_get_reg_format(void *node, u32 *naddr, u32 *nsize);
+int dt_get_virtual_reg(void *node, void **addr, int nres);
 
 static inline void *finddevice(const char *name)
 {