ppc440spe-adma: adds updated ppc440spe adma driver

This patch adds new version of the PPC440SPe ADMA driver.
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

Documentation/powerpc/dts-bindings/4xx/ppc440spe-adma.txt

+PPC440SPe DMA/XOR (DMA Controller and XOR Accelerator)
+
+Device nodes needed for operation of the ppc440spe-adma driver
+are specified hereby. These are I2O/DMA, DMA and XOR nodes
+for DMA engines and Memory Queue Module node. The latter is used
+by ADMA driver for configuration of RAID-6 H/W capabilities of
+the PPC440SPe. In addition to the nodes and properties described
+below, the ranges property of PLB node must specify ranges for
+DMA devices.
+
+ i) The I2O node
+
+ Required properties:
+
+ - compatible		: "ibm,i2o-440spe";
+ - reg			: <registers mapping>
+ - dcr-reg		: <DCR registers range>
+
+ Example:
+
+	I2O: i2o@400100000 {
+		compatible = "ibm,i2o-440spe";
+		reg = <0x00000004 0x00100000 0x100>;
+		dcr-reg = <0x060 0x020>;
+	};
+
+
+ ii) The DMA node
+
+ Required properties:
+
+ - compatible		: "ibm,dma-440spe";
+ - cell-index		: 1 cell, hardware index of the DMA engine
+			  (typically 0x0 and 0x1 for DMA0 and DMA1)
+ - reg			: <registers mapping>
+ - dcr-reg		: <DCR registers range>
+ - interrupts		: <interrupt mapping for DMA0/1 interrupts sources:
+			   2 sources: DMAx CS FIFO Needs Service IRQ (on UIC0)
+			   and DMA Error IRQ (on UIC1). The latter is common
+			   for both DMA engines>.
+ - interrupt-parent	: needed for interrupt mapping
+
+ Example:
+
+	DMA0: dma0@400100100 {
+		compatible = "ibm,dma-440spe";
+		cell-index = <0>;
+		reg = <0x00000004 0x00100100 0x100>;
+		dcr-reg = <0x060 0x020>;
+		interrupt-parent = <&DMA0>;
+		interrupts = <0 1>;
+		#interrupt-cells = <1>;
+		#address-cells = <0>;
+		#size-cells = <0>;
+		interrupt-map = <
+			0 &UIC0 0x14 4
+			1 &UIC1 0x16 4>;
+	};
+
+
+ iii) XOR Accelerator node
+
+ Required properties:
+
+ - compatible		: "amcc,xor-accelerator";
+ - reg			: <registers mapping>
+ - interrupts		: <interrupt mapping for XOR interrupt source>
+ - interrupt-parent	: for interrupt mapping
+
+ Example:
+
+	xor-accel@400200000 {
+		compatible = "amcc,xor-accelerator";
+		reg = <0x00000004 0x00200000 0x400>;
+		interrupt-parent = <&UIC1>;
+		interrupts = <0x1f 4>;
+	};
+
+
+ iv) Memory Queue Module node
+
+ Required properties:
+
+ - compatible		: "ibm,mq-440spe";
+ - dcr-reg		: <DCR registers range>
+
+ Example:
+
+	MQ0: mq {
+		compatible = "ibm,mq-440spe";
+		dcr-reg = <0x040 0x020>;
+	};
+

arch/powerpc/include/asm/async_tx.h

+/*
+ * Copyright (C) 2008-2009 DENX Software Engineering.
+ *
+ * Author: Yuri Tikhonov <yur@emcraft.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the Free
+ * Software Foundation; either version 2 of the License, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program; if not, write to the Free Software Foundation, Inc., 59
+ * Temple Place - Suite 330, Boston, MA  02111-1307, USA.
+ *
+ * The full GNU General Public License is included in this distribution in the
+ * file called COPYING.
+ */
+#ifndef _ASM_POWERPC_ASYNC_TX_H_
+#define _ASM_POWERPC_ASYNC_TX_H_
+
+#if defined(CONFIG_440SPe) || defined(CONFIG_440SP)
+extern struct dma_chan *
+ppc440spe_async_tx_find_best_channel(enum dma_transaction_type cap,
+	struct page **dst_lst, int dst_cnt, struct page **src_lst,
+	int src_cnt, size_t src_sz);
+
+#define async_tx_find_channel(dep, cap, dst_lst, dst_cnt, src_lst, \
+			      src_cnt, src_sz) \
+	ppc440spe_async_tx_find_best_channel(cap, dst_lst, dst_cnt, src_lst, \
+					     src_cnt, src_sz)
+#else
+
+#define async_tx_find_channel(dep, type, dst, dst_count, src, src_count, len) \
+	__async_tx_find_channel(dep, type)
+
+struct dma_chan *
+__async_tx_find_channel(struct async_submit_ctl *submit,
+			enum dma_transaction_type tx_type);
+
+#endif
+
+#endif

arch/powerpc/include/asm/dcr-regs.h

@@ -157,4 +157,27 @@
 #define  L2C_SNP_SSR_32G	0x0000f000
 #define  L2C_SNP_ESR		0x00000800
 
+/*
+ * DCR register offsets for 440SP/440SPe I2O/DMA controller.
+ * The base address is configured in the device tree.
+ */
+#define DCRN_I2O0_IBAL		0x006
+#define DCRN_I2O0_IBAH		0x007
+#define I2O_REG_ENABLE		0x00000001	/* Enable I2O/DMA access */
+
+/* 440SP/440SPe Software Reset DCR */
+#define DCRN_SDR0_SRST		0x0200
+#define DCRN_SDR0_SRST_I2ODMA	(0x80000000 >> 15)	/* Reset I2O/DMA */
+
+/* 440SP/440SPe Memory Queue DCR offsets */
+#define DCRN_MQ0_XORBA		0x04
+#define DCRN_MQ0_CF2H		0x06
+#define DCRN_MQ0_CFBHL		0x0f
+#define DCRN_MQ0_BAUH		0x10
+
+/* HB/LL Paths Configuration Register */
+#define MQ0_CFBHL_TPLM		28
+#define MQ0_CFBHL_HBCL		23
+#define MQ0_CFBHL_POLY		15
+
 #endif /* __DCR_REGS_H__ */

drivers/dma/Kconfig

@@ -116,6 +116,17 @@ config COH901318
 	help
 	  Enable support for ST-Ericsson COH 901 318 DMA.
 
+config AMCC_PPC440SPE_ADMA
+	tristate "AMCC PPC440SPe ADMA support"
+	depends on 440SPe || 440SP
+	select DMA_ENGINE
+	select ARCH_HAS_ASYNC_TX_FIND_CHANNEL
+	help
+	  Enable support for the AMCC PPC440SPe RAID engines.
+
+config ARCH_HAS_ASYNC_TX_FIND_CHANNEL
+	bool
+
 config DMA_ENGINE
 	bool
 

drivers/dma/Makefile

@@ -11,3 +11,4 @@ obj-$(CONFIG_MX3_IPU) += ipu/
 obj-$(CONFIG_TXX9_DMAC) += txx9dmac.o
 obj-$(CONFIG_SH_DMAE) += shdma.o
 obj-$(CONFIG_COH901318) += coh901318.o coh901318_lli.o
+obj-$(CONFIG_AMCC_PPC440SPE_ADMA) += ppc4xx/

drivers/dma/ppc4xx/Makefile

+obj-$(CONFIG_AMCC_PPC440SPE_ADMA) += adma.o

drivers/dma/ppc4xx/adma.h

+/*
+ * 2006-2009 (C) DENX Software Engineering.
+ *
+ * Author: Yuri Tikhonov <yur@emcraft.com>
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2.  This program is licensed "as is" without any warranty of
+ * any kind, whether express or implied.
+ */
+
+#ifndef _PPC440SPE_ADMA_H
+#define _PPC440SPE_ADMA_H
+
+#include <linux/types.h>
+#include "dma.h"
+#include "xor.h"
+
+#define to_ppc440spe_adma_chan(chan) \
+		container_of(chan, struct ppc440spe_adma_chan, common)
+#define to_ppc440spe_adma_device(dev) \
+		container_of(dev, struct ppc440spe_adma_device, common)
+#define tx_to_ppc440spe_adma_slot(tx) \
+		container_of(tx, struct ppc440spe_adma_desc_slot, async_tx)
+
+/* Default polynomial (for 440SP is only available) */
+#define PPC440SPE_DEFAULT_POLY	0x4d
+
+#define PPC440SPE_ADMA_ENGINES_NUM	(XOR_ENGINES_NUM + DMA_ENGINES_NUM)
+
+#define PPC440SPE_ADMA_WATCHDOG_MSEC	3
+#define PPC440SPE_ADMA_THRESHOLD	1
+
+#define PPC440SPE_DMA0_ID	0
+#define PPC440SPE_DMA1_ID	1
+#define PPC440SPE_XOR_ID	2
+
+#define PPC440SPE_ADMA_DMA_MAX_BYTE_COUNT	0xFFFFFFUL
+/* this is the XOR_CBBCR width */
+#define PPC440SPE_ADMA_XOR_MAX_BYTE_COUNT	(1 << 31)
+#define PPC440SPE_ADMA_ZERO_SUM_MAX_BYTE_COUNT PPC440SPE_ADMA_XOR_MAX_BYTE_COUNT
+
+#define PPC440SPE_RXOR_RUN	0
+
+#define MQ0_CF2H_RXOR_BS_MASK	0x1FF
+
+#undef ADMA_LL_DEBUG
+
+/**
+ * struct ppc440spe_adma_device - internal representation of an ADMA device
+ * @dev: device
+ * @dma_reg: base for DMAx register access
+ * @xor_reg: base for XOR register access
+ * @i2o_reg: base for I2O register access
+ * @id: HW ADMA Device selector
+ * @dma_desc_pool_virt: base of DMA descriptor region (CPU address)
+ * @dma_desc_pool: base of DMA descriptor region (DMA address)
+ * @pool_size: size of the pool
+ * @irq: DMAx or XOR irq number
+ * @err_irq: DMAx error irq number
+ * @common: embedded struct dma_device
+ */
+struct ppc440spe_adma_device {
+	struct device *dev;
+	struct dma_regs __iomem *dma_reg;
+	struct xor_regs __iomem *xor_reg;
+	struct i2o_regs __iomem *i2o_reg;
+	int id;
+	void *dma_desc_pool_virt;
+	dma_addr_t dma_desc_pool;
+	size_t pool_size;
+	int irq;
+	int err_irq;
+	struct dma_device common;
+};
+
+/**
+ * struct ppc440spe_adma_chan - internal representation of an ADMA channel
+ * @lock: serializes enqueue/dequeue operations to the slot pool
+ * @device: parent device
+ * @chain: device chain view of the descriptors
+ * @common: common dmaengine channel object members
+ * @all_slots: complete domain of slots usable by the channel
+ * @pending: allows batching of hardware operations
+ * @completed_cookie: identifier for the most recently completed operation
+ * @slots_allocated: records the actual size of the descriptor slot pool
+ * @hw_chain_inited: h/w descriptor chain initialization flag
+ * @irq_tasklet: bottom half where ppc440spe_adma_slot_cleanup runs
+ * @needs_unmap: if buffers should not be unmapped upon final processing
+ * @pdest_page: P destination page for async validate operation
+ * @qdest_page: Q destination page for async validate operation
+ * @pdest: P dma addr for async validate operation
+ * @qdest: Q dma addr for async validate operation
+ */
+struct ppc440spe_adma_chan {
+	spinlock_t lock;
+	struct ppc440spe_adma_device *device;
+	struct list_head chain;
+	struct dma_chan common;
+	struct list_head all_slots;
+	struct ppc440spe_adma_desc_slot *last_used;
+	int pending;
+	dma_cookie_t completed_cookie;
+	int slots_allocated;
+	int hw_chain_inited;
+	struct tasklet_struct irq_tasklet;
+	u8 needs_unmap;
+	struct page *pdest_page;
+	struct page *qdest_page;
+	dma_addr_t pdest;
+	dma_addr_t qdest;
+};
+
+struct ppc440spe_rxor {
+	u32 addrl;
+	u32 addrh;
+	int len;
+	int xor_count;
+	int addr_count;
+	int desc_count;
+	int state;
+};
+
+/**
+ * struct ppc440spe_adma_desc_slot - PPC440SPE-ADMA software descriptor
+ * @phys: hardware address of the hardware descriptor chain
+ * @group_head: first operation in a transaction
+ * @hw_next: pointer to the next descriptor in chain
+ * @async_tx: support for the async_tx api
+ * @slot_node: node on the iop_adma_chan.all_slots list
+ * @chain_node: node on the op_adma_chan.chain list
+ * @group_list: list of slots that make up a multi-descriptor transaction
+ *              for example transfer lengths larger than the supported hw max
+ * @unmap_len: transaction bytecount
+ * @hw_desc: virtual address of the hardware descriptor chain
+ * @stride: currently chained or not
+ * @idx: pool index
+ * @slot_cnt: total slots used in an transaction (group of operations)
+ * @src_cnt: number of sources set in this descriptor
+ * @dst_cnt: number of destinations set in the descriptor
+ * @slots_per_op: number of slots per operation
+ * @descs_per_op: number of slot per P/Q operation see comment
+ *                for ppc440spe_prep_dma_pqxor function
+ * @flags: desc state/type
+ * @reverse_flags: 1 if a corresponding rxor address uses reversed address order
+ * @xor_check_result: result of zero sum
+ * @crc32_result: result crc calculation
+ */
+struct ppc440spe_adma_desc_slot {
+	dma_addr_t phys;
+	struct ppc440spe_adma_desc_slot *group_head;
+	struct ppc440spe_adma_desc_slot *hw_next;
+	struct dma_async_tx_descriptor async_tx;
+	struct list_head slot_node;
+	struct list_head chain_node; /* node in channel ops list */
+	struct list_head group_list; /* list */
+	unsigned int unmap_len;
+	void *hw_desc;
+	u16 stride;
+	u16 idx;
+	u16 slot_cnt;
+	u8 src_cnt;
+	u8 dst_cnt;
+	u8 slots_per_op;
+	u8 descs_per_op;
+	unsigned long flags;
+	unsigned long reverse_flags[8];
+
+#define PPC440SPE_DESC_INT	0	/* generate interrupt on complete */
+#define PPC440SPE_ZERO_P	1	/* clear P destionaion */
+#define PPC440SPE_ZERO_Q	2	/* clear Q destination */
+#define PPC440SPE_COHERENT	3	/* src/dst are coherent */
+
+#define PPC440SPE_DESC_WXOR	4	/* WXORs are in chain */
+#define PPC440SPE_DESC_RXOR	5	/* RXOR is in chain */
+
+#define PPC440SPE_DESC_RXOR123	8	/* CDB for RXOR123 operation */
+#define PPC440SPE_DESC_RXOR124	9	/* CDB for RXOR124 operation */
+#define PPC440SPE_DESC_RXOR125	10	/* CDB for RXOR125 operation */
+#define PPC440SPE_DESC_RXOR12	11	/* CDB for RXOR12 operation */
+#define PPC440SPE_DESC_RXOR_REV	12	/* CDB has srcs in reversed order */
+
+#define PPC440SPE_DESC_PCHECK	13
+#define PPC440SPE_DESC_QCHECK	14
+
+#define PPC440SPE_DESC_RXOR_MSK	0x3
+
+	struct ppc440spe_rxor rxor_cursor;
+
+	union {
+		u32 *xor_check_result;
+		u32 *crc32_result;
+	};
+};
+
+#endif /* _PPC440SPE_ADMA_H */

drivers/dma/ppc4xx/dma.h

+/*
+ * 440SPe's DMA engines support header file
+ *
+ * 2006-2009 (C) DENX Software Engineering.
+ *
+ * Author: Yuri Tikhonov <yur@emcraft.com>
+ *
+ * This file is licensed under the term of  the GNU General Public License
+ * version 2. The program licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+#ifndef	_PPC440SPE_DMA_H
+#define _PPC440SPE_DMA_H
+
+#include <linux/types.h>
+
+/* Number of elements in the array with statical CDBs */
+#define	MAX_STAT_DMA_CDBS	16
+/* Number of DMA engines available on the contoller */
+#define DMA_ENGINES_NUM		2
+
+/* Maximum h/w supported number of destinations */
+#define DMA_DEST_MAX_NUM	2
+
+/* FIFO's params */
+#define DMA0_FIFO_SIZE		0x1000
+#define DMA1_FIFO_SIZE		0x1000
+#define DMA_FIFO_ENABLE		(1<<12)
+
+/* DMA Configuration Register. Data Transfer Engine PLB Priority: */
+#define DMA_CFG_DXEPR_LP	(0<<26)
+#define DMA_CFG_DXEPR_HP	(3<<26)
+#define DMA_CFG_DXEPR_HHP	(2<<26)
+#define DMA_CFG_DXEPR_HHHP	(1<<26)
+
+/* DMA Configuration Register. DMA FIFO Manager PLB Priority: */
+#define DMA_CFG_DFMPP_LP	(0<<23)
+#define DMA_CFG_DFMPP_HP	(3<<23)
+#define DMA_CFG_DFMPP_HHP	(2<<23)
+#define DMA_CFG_DFMPP_HHHP	(1<<23)
+
+/* DMA Configuration Register. Force 64-byte Alignment */
+#define DMA_CFG_FALGN		(1 << 19)
+
+/*UIC0:*/
+#define D0CPF_INT		(1<<12)
+#define D0CSF_INT		(1<<11)
+#define D1CPF_INT		(1<<10)
+#define D1CSF_INT		(1<<9)
+/*UIC1:*/
+#define DMAE_INT		(1<<9)
+
+/* I2O IOP Interrupt Mask Register */
+#define I2O_IOPIM_P0SNE		(1<<3)
+#define I2O_IOPIM_P0EM		(1<<5)
+#define I2O_IOPIM_P1SNE		(1<<6)
+#define I2O_IOPIM_P1EM		(1<<8)
+
+/* DMA CDB fields */
+#define DMA_CDB_MSK		(0xF)
+#define DMA_CDB_64B_ADDR	(1<<2)
+#define DMA_CDB_NO_INT		(1<<3)
+#define DMA_CDB_STATUS_MSK	(0x3)
+#define DMA_CDB_ADDR_MSK	(0xFFFFFFF0)
+
+/* DMA CDB OpCodes */
+#define DMA_CDB_OPC_NO_OP	(0x00)
+#define DMA_CDB_OPC_MV_SG1_SG2	(0x01)
+#define DMA_CDB_OPC_MULTICAST	(0x05)
+#define DMA_CDB_OPC_DFILL128	(0x24)
+#define DMA_CDB_OPC_DCHECK128	(0x23)
+
+#define DMA_CUED_XOR_BASE	(0x10000000)
+#define DMA_CUED_XOR_HB		(0x00000008)
+
+#ifdef CONFIG_440SP
+#define DMA_CUED_MULT1_OFF	0
+#define DMA_CUED_MULT2_OFF	8
+#define DMA_CUED_MULT3_OFF	16
+#define DMA_CUED_REGION_OFF	24
+#define DMA_CUED_XOR_WIN_MSK	(0xFC000000)
+#else
+#define DMA_CUED_MULT1_OFF	2
+#define DMA_CUED_MULT2_OFF	10
+#define DMA_CUED_MULT3_OFF	18
+#define DMA_CUED_REGION_OFF	26
+#define DMA_CUED_XOR_WIN_MSK	(0xF0000000)
+#endif
+
+#define DMA_CUED_REGION_MSK	0x3
+#define DMA_RXOR123		0x0
+#define DMA_RXOR124		0x1
+#define DMA_RXOR125		0x2
+#define DMA_RXOR12		0x3
+
+/* S/G addresses */
+#define DMA_CDB_SG_SRC		1
+#define DMA_CDB_SG_DST1		2
+#define DMA_CDB_SG_DST2		3
+
+/*
+ * DMAx engines Command Descriptor Block Type
+ */
+struct dma_cdb {
+	/*
+	 * Basic CDB structure (Table 20-17, p.499, 440spe_um_1_22.pdf)
+	 */
+	u8	pad0[2];        /* reserved */
+	u8	attr;		/* attributes */
+	u8	opc;		/* opcode */
+	u32	sg1u;		/* upper SG1 address */
+	u32	sg1l;		/* lower SG1 address */
+	u32	cnt;		/* SG count, 3B used */
+	u32	sg2u;		/* upper SG2 address */
+	u32	sg2l;		/* lower SG2 address */
+	u32	sg3u;		/* upper SG3 address */
+	u32	sg3l;		/* lower SG3 address */
+};
+
+/*
+ * DMAx hardware registers (p.515 in 440SPe UM 1.22)
+ */
+struct dma_regs {
+	u32	cpfpl;
+	u32	cpfph;
+	u32	csfpl;
+	u32	csfph;
+	u32	dsts;
+	u32	cfg;
+	u8	pad0[0x8];
+	u16	cpfhp;
+	u16	cpftp;
+	u16	csfhp;
+	u16	csftp;
+	u8	pad1[0x8];
+	u32	acpl;
+	u32	acph;
+	u32	s1bpl;
+	u32	s1bph;
+	u32	s2bpl;
+	u32	s2bph;
+	u32	s3bpl;
+	u32	s3bph;
+	u8	pad2[0x10];
+	u32	earl;
+	u32	earh;
+	u8	pad3[0x8];
+	u32	seat;
+	u32	sead;
+	u32	op;
+	u32	fsiz;
+};
+
+/*
+ * I2O hardware registers (p.528 in 440SPe UM 1.22)
+ */
+struct i2o_regs {
+	u32	ists;
+	u32	iseat;
+	u32	isead;
+	u8	pad0[0x14];
+	u32	idbel;
+	u8	pad1[0xc];
+	u32	ihis;
+	u32	ihim;
+	u8	pad2[0x8];
+	u32	ihiq;
+	u32	ihoq;
+	u8	pad3[0x8];
+	u32	iopis;
+	u32	iopim;
+	u32	iopiq;
+	u8	iopoq;
+	u8	pad4[3];
+	u16	iiflh;
+	u16	iiflt;
+	u16	iiplh;
+	u16	iiplt;
+	u16	ioflh;
+	u16	ioflt;
+	u16	ioplh;
+	u16	ioplt;
+	u32	iidc;
+	u32	ictl;
+	u32	ifcpp;
+	u8	pad5[0x4];
+	u16	mfac0;
+	u16	mfac1;
+	u16	mfac2;
+	u16	mfac3;
+	u16	mfac4;
+	u16	mfac5;
+	u16	mfac6;
+	u16	mfac7;
+	u16	ifcfh;
+	u16	ifcht;
+	u8	pad6[0x4];
+	u32	iifmc;
+	u32	iodb;
+	u32	iodbc;
+	u32	ifbal;
+	u32	ifbah;
+	u32	ifsiz;
+	u32	ispd0;
+	u32	ispd1;
+	u32	ispd2;
+	u32	ispd3;
+	u32	ihipl;
+	u32	ihiph;
+	u32	ihopl;
+	u32	ihoph;
+	u32	iiipl;
+	u32	iiiph;
+	u32	iiopl;
+	u32	iioph;
+	u32	ifcpl;
+	u32	ifcph;
+	u8	pad7[0x8];
+	u32	iopt;
+};
+
+#endif /* _PPC440SPE_DMA_H */

drivers/dma/ppc4xx/xor.h

+/*
+ * 440SPe's XOR engines support header file
+ *
+ * 2006-2009 (C) DENX Software Engineering.
+ *
+ * Author: Yuri Tikhonov <yur@emcraft.com>
+ *
+ * This file is licensed under the term of  the GNU General Public License
+ * version 2. The program licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+#ifndef _PPC440SPE_XOR_H
+#define _PPC440SPE_XOR_H
+
+#include <linux/types.h>
+
+/* Number of XOR engines available on the contoller */
+#define XOR_ENGINES_NUM		1
+
+/* Number of operands supported in the h/w */
+#define XOR_MAX_OPS		16
+
+/*
+ * XOR Command Block Control Register bits
+ */
+#define XOR_CBCR_LNK_BIT        (1<<31) /* link present */
+#define XOR_CBCR_TGT_BIT        (1<<30) /* target present */
+#define XOR_CBCR_CBCE_BIT       (1<<29) /* command block compete enable */
+#define XOR_CBCR_RNZE_BIT       (1<<28) /* result not zero enable */
+#define XOR_CBCR_XNOR_BIT       (1<<15) /* XOR/XNOR */
+#define XOR_CDCR_OAC_MSK        (0x7F)  /* operand address count */
+
+/*
+ * XORCore Status Register bits
+ */
+#define XOR_SR_XCP_BIT		(1<<31)	/* core processing */
+#define XOR_SR_ICB_BIT		(1<<17)	/* invalid CB */
+#define XOR_SR_IC_BIT		(1<<16)	/* invalid command */
+#define XOR_SR_IPE_BIT		(1<<15)	/* internal parity error */
+#define XOR_SR_RNZ_BIT		(1<<2)	/* result not Zero */
+#define XOR_SR_CBC_BIT		(1<<1)	/* CB complete */
+#define XOR_SR_CBLC_BIT		(1<<0)	/* CB list complete */
+
+/*
+ * XORCore Control Set and Reset Register bits
+ */
+#define XOR_CRSR_XASR_BIT	(1<<31)	/* soft reset */
+#define XOR_CRSR_XAE_BIT	(1<<30)	/* enable */
+#define XOR_CRSR_RCBE_BIT	(1<<29)	/* refetch CB enable */
+#define XOR_CRSR_PAUS_BIT	(1<<28)	/* pause */
+#define XOR_CRSR_64BA_BIT	(1<<27) /* 64/32 CB format */
+#define XOR_CRSR_CLP_BIT	(1<<25)	/* continue list processing */
+
+/*
+ * XORCore Interrupt Enable Register
+ */
+#define XOR_IE_ICBIE_BIT	(1<<17)	/* Invalid Command Block IRQ Enable */
+#define XOR_IE_ICIE_BIT		(1<<16)	/* Invalid Command IRQ Enable */
+#define XOR_IE_RPTIE_BIT	(1<<14)	/* Read PLB Timeout Error IRQ Enable */
+#define XOR_IE_CBCIE_BIT	(1<<1)	/* CB complete interrupt enable */
+#define XOR_IE_CBLCI_BIT	(1<<0)	/* CB list complete interrupt enable */
+
+/*
+ * XOR Accelerator engine Command Block Type
+ */
+struct xor_cb {
+	/*
+	 * Basic 64-bit format XOR CB (Table 19-1, p.463, 440spe_um_1_22.pdf)
+	 */
+	u32	cbc;		/* control */
+	u32	cbbc;		/* byte count */
+	u32	cbs;		/* status */
+	u8	pad0[4];	/* reserved */
+	u32	cbtah;		/* target address high */
+	u32	cbtal;		/* target address low */
+	u32	cblah;		/* link address high */
+	u32	cblal;		/* link address low */
+	struct {
+		u32 h;
+		u32 l;
+	} __attribute__ ((packed)) ops[16];
+} __attribute__ ((packed));
+
+/*
+ * XOR hardware registers Table 19-3, UM 1.22
+ */
+struct xor_regs {
+	u32	op_ar[16][2];	/* operand address[0]-high,[1]-low registers */
+	u8	pad0[352];	/* reserved */
+	u32	cbcr;		/* CB control register */
+	u32	cbbcr;		/* CB byte count register */
+	u32	cbsr;		/* CB status register */
+	u8	pad1[4];	/* reserved */
+	u32	cbtahr;		/* operand target address high register */
+	u32	cbtalr;		/* operand target address low register */
+	u32	cblahr;		/* CB link address high register */
+	u32	cblalr;		/* CB link address low register */
+	u32	crsr;		/* control set register */
+	u32	crrr;		/* control reset register */
+	u32	ccbahr;		/* current CB address high register */
+	u32	ccbalr;		/* current CB address low register */
+	u32	plbr;		/* PLB configuration register */
+	u32	ier;		/* interrupt enable register */
+	u32	pecr;		/* parity error count register */
+	u32	sr;		/* status register */
+	u32	revidr;		/* revision ID register */
+};
+
+#endif /* _PPC440SPE_XOR_H */