Merge tag 'spi-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi

Pull spi updates from Mark Brown:
 "Not much going on in the core for SPI this time but a reasonable
  amount of change in the drivers:

   - Removal of dmal_request_slave_channel() from Peter Ujfalusi.

   - More conversions of drivers to GPIO descriptors from Linus Walleij.

   - A big rework of the sh-msiof driver from Geert Uytterhoeven moving
     it over to the generic native chipselect support.

   - DMA support for the uniphier driver from Kunihiko Hayashi.

   - New driver support for HiSilcon v3xx SPI NOR controllers from John
     Garry"

* tag 'spi-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (52 commits)
  dt-binding: spi: add NPCM PSPI reset binding
  spi: pxa2xx: Avoid touching SSCR0_SSE on MMP2
  spi: spi-fsl-qspi: Ensure width is respected in spi-mem operations
  spi: npcm-pspi: modify reset support
  spi: npcm-pspi: improve spi transfer performance
  spi: spi-ti-qspi: fix warning
  spi: npcm-pspi: fix 16 bit send and receive support
  spi: pxa2xx: Add support for Intel Comet Lake PCH-V
  spi: fsl: simplify error path in of_fsl_spi_probe()
  spi: fsl-lpspi: fix only one cs-gpio working
  spi: spi-ti-qspi: optimize byte-transfers
  spi: spi-ti-qspi: support large flash devices
  spi: spi-qcom-qspi: Use device managed memory for clk_bulk_data
  MAINTAINERS: Add a maintainer for the HiSilicon v3xx SFC driver
  spi: Add HiSilicon v3xx SPI NOR flash controller driver
  dt-bindings: spi_atmel: add microchip,sam9x60-spi
  spi: bcm2835: Raise maximum number of slaves to 4
  spi: sh-msiof: Do not redefine STR while compile testing
  spi: rspi: Add support for GPIO chip selects
  spi: rspi: Add support for multiple native chip selects
  ...

Documentation/devicetree/bindings/spi/nuvoton,npcm-pspi.txt

@@ -12,6 +12,7 @@ Required properties:
  - clock-names: Should be "clk_apb5".
  - pinctrl-names : a pinctrl state named "default" must be defined.
  - pinctrl-0 : phandle referencing pin configuration of the device.
+ - resets : phandle to the reset control for this device.
  - cs-gpios: Specifies the gpio pins to be used for chipselects.
             See: Documentation/devicetree/bindings/spi/spi-bus.txt
 
@@ -19,16 +20,6 @@ Optional properties:
 - clock-frequency : Input clock frequency to the PSPI block in Hz.
 		    Default is 25000000 Hz.
 
-Aliases:
-- All the SPI controller nodes should be represented in the aliases node using
-  the following format 'spi{n}' withe the correct numbered in "aliases" node.
-
-Example:
-
-aliases {
-	spi0 = &spi0;
-};
-
 spi0: spi@f0200000 {
 	compatible = "nuvoton,npcm750-pspi";
 	reg = <0xf0200000 0x1000>;
@@ -39,5 +30,6 @@ spi0: spi@f0200000 {
 	interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
 	clocks = <&clk NPCM7XX_CLK_APB5>;
 	clock-names = "clk_apb5";
+	resets = <&rstc NPCM7XX_RESET_IPSRST2 NPCM7XX_RESET_PSPI1>
 	cs-gpios = <&gpio6 11 GPIO_ACTIVE_LOW>;
 };

Documentation/devicetree/bindings/spi/spi-stm32.txt

-STMicroelectronics STM32 SPI Controller
-
-The STM32 SPI controller is used to communicate with external devices using
-the Serial Peripheral Interface. It supports full-duplex, half-duplex and
-simplex synchronous serial communication with external devices. It supports
-from 4 to 32-bit data size. Although it can be configured as master or slave,
-only master is supported by the driver.
-
-Required properties:
-- compatible: Should be one of:
-  "st,stm32h7-spi"
-  "st,stm32f4-spi"
-- reg: Offset and length of the device's register set.
-- interrupts: Must contain the interrupt id.
-- clocks: Must contain an entry for spiclk (which feeds the internal clock
-	  generator).
-- #address-cells:  Number of cells required to define a chip select address.
-- #size-cells: Should be zero.
-
-Optional properties:
-- resets: Must contain the phandle to the reset controller.
-- A pinctrl state named "default" may be defined to set pins in mode of
-  operation for SPI transfer.
-- dmas: DMA specifiers for tx and rx dma. DMA fifo mode must be used. See the
-  STM32 DMA bindings, Documentation/devicetree/bindings/dma/stm32-dma.txt.
-- dma-names: DMA request names should include "tx" and "rx" if present.
-- cs-gpios: list of GPIO chip selects. See the SPI bus bindings,
-  Documentation/devicetree/bindings/spi/spi-bus.txt
-
-
-Child nodes represent devices on the SPI bus
-  See ../spi/spi-bus.txt
-
-Optional properties:
-- st,spi-midi-ns: Only for STM32H7, (Master Inter-Data Idleness) minimum time
-		  delay in nanoseconds inserted between two consecutive data
-		  frames.
-
-
-Example:
-	spi2: spi@40003800 {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		compatible = "st,stm32h7-spi";
-		reg = <0x40003800 0x400>;
-		interrupts = <36>;
-		clocks = <&rcc SPI2_CK>;
-		resets = <&rcc 1166>;
-		dmas = <&dmamux1 0 39 0x400 0x01>,
-		       <&dmamux1 1 40 0x400 0x01>;
-		dma-names = "rx", "tx";
-		pinctrl-0 = <&spi2_pins_b>;
-		pinctrl-names = "default";
-		cs-gpios = <&gpioa 11 0>;
-
-		aardvark@0 {
-			compatible = "totalphase,aardvark";
-			reg = <0>;
-			spi-max-frequency = <4000000>;
-			st,spi-midi-ns = <4000>;
-		};
-	};

Documentation/devicetree/bindings/spi/spi_atmel.txt

 Atmel SPI device
 
 Required properties:
-- compatible : should be "atmel,at91rm9200-spi".
+- compatible : should be "atmel,at91rm9200-spi" or "microchip,sam9x60-spi".
 - reg: Address and length of the register set for the device
 - interrupts: Should contain spi interrupt
 - cs-gpios: chipselects (optional for SPI controller version >= 2 with the

Documentation/devicetree/bindings/spi/st,stm32-spi.yaml

+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/spi/st,stm32-spi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: STMicroelectronics STM32 SPI Controller bindings
+
+description: |
+  The STM32 SPI controller is used to communicate with external devices using
+  the Serial Peripheral Interface. It supports full-duplex, half-duplex and
+  simplex synchronous serial communication with external devices. It supports
+  from 4 to 32-bit data size.
+
+maintainers:
+  - Erwan Leray <erwan.leray@st.com>
+  - Fabrice Gasnier <fabrice.gasnier@st.com>
+
+allOf:
+  - $ref: "spi-controller.yaml#"
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: st,stm32f4-spi
+
+    then:
+      properties:
+        st,spi-midi-ns: false
+
+properties:
+  compatible:
+    enum:
+      - st,stm32f4-spi
+      - st,stm32h7-spi
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  resets:
+    maxItems: 1
+
+  dmas:
+    description: |
+      DMA specifiers for tx and rx dma. DMA fifo mode must be used. See
+      the STM32 DMA bindings Documentation/devicetree/bindings/dma/stm32-dma.txt.
+    items:
+      - description: rx DMA channel
+      - description: tx DMA channel
+
+  dma-names:
+    items:
+      - const: rx
+      - const: tx
+
+patternProperties:
+  "^[a-zA-Z][a-zA-Z0-9,+\\-._]{0,63}@[0-9a-f]+$":
+    type: object
+    # SPI slave nodes must be children of the SPI master node and can
+    # contain the following properties.
+    properties:
+      st,spi-midi-ns:
+        description: |
+          Only for STM32H7, (Master Inter-Data Idleness) minimum time
+          delay in nanoseconds inserted between two consecutive data frames.
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - interrupts
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/clock/stm32mp1-clks.h>
+    #include <dt-bindings/reset/stm32mp1-resets.h>
+    spi@4000b000 {
+      #address-cells = <1>;
+      #size-cells = <0>;
+      compatible = "st,stm32h7-spi";
+      reg = <0x4000b000 0x400>;
+      interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+      clocks = <&rcc SPI2_K>;
+      resets = <&rcc SPI2_R>;
+      dmas = <&dmamux1 0 39 0x400 0x05>,
+             <&dmamux1 1 40 0x400 0x05>;
+      dma-names = "rx", "tx";
+      cs-gpios = <&gpioa 11 0>;
+
+      aardvark@0 {
+        compatible = "totalphase,aardvark";
+        reg = <0>;
+        spi-max-frequency = <4000000>;
+        st,spi-midi-ns = <4000>;
+      };
+    };
+
+...

MAINTAINERS

@@ -7509,6 +7509,12 @@ S:	Supported
 F:	drivers/scsi/hisi_sas/
 F:	Documentation/devicetree/bindings/scsi/hisilicon-sas.txt
 
+HISILICON V3XX SPI NOR FLASH Controller Driver
+M:	John Garry <john.garry@huawei.com>
+W:	http://www.hisilicon.com
+S:	Maintained
+F:	drivers/spi/spi-hisi-sfc-v3xx.c
+
 HISILICON QM AND ZIP Controller DRIVER
 M:	Zhou Wang <wangzhou1@hisilicon.com>
 L:	linux-crypto@vger.kernel.org

drivers/spi/Kconfig

@@ -281,6 +281,15 @@ config SPI_FSL_QUADSPI
 	  This controller does not support generic SPI messages. It only
 	  supports the high-level SPI memory interface.
 
+config SPI_HISI_SFC_V3XX
+	tristate "HiSilicon SPI-NOR Flash Controller for Hi16XX chipsets"
+	depends on (ARM64 && ACPI) || COMPILE_TEST
+	depends on HAS_IOMEM
+	select CONFIG_MTD_SPI_NOR
+	help
+	  This enables support for HiSilicon v3xx SPI-NOR flash controller
+	  found in hi16xx chipsets.
+
 config SPI_NXP_FLEXSPI
 	tristate "NXP Flex SPI controller"
 	depends on ARCH_LAYERSCAPE || HAS_IOMEM

drivers/spi/Makefile

@@ -48,6 +48,7 @@ obj-$(CONFIG_SPI_FSL_LPSPI)		+= spi-fsl-lpspi.o
 obj-$(CONFIG_SPI_FSL_QUADSPI)		+= spi-fsl-qspi.o
 obj-$(CONFIG_SPI_FSL_SPI)		+= spi-fsl-spi.o
 obj-$(CONFIG_SPI_GPIO)			+= spi-gpio.o
+obj-$(CONFIG_SPI_HISI_SFC_V3XX)		+= spi-hisi-sfc-v3xx.o
 obj-$(CONFIG_SPI_IMG_SPFI)		+= spi-img-spfi.o
 obj-$(CONFIG_SPI_IMX)			+= spi-imx.o
 obj-$(CONFIG_SPI_LANTIQ_SSC)		+= spi-lantiq-ssc.o

drivers/spi/spi-atmel.c

@@ -514,26 +514,19 @@ static int atmel_spi_configure_dma(struct spi_master *master,
 	master->dma_tx = dma_request_chan(dev, "tx");
 	if (IS_ERR(master->dma_tx)) {
 		err = PTR_ERR(master->dma_tx);
-		if (err == -EPROBE_DEFER) {
-			dev_warn(dev, "no DMA channel available at the moment\n");
-			goto error_clear;
-		}
-		dev_err(dev,
-			"DMA TX channel not available, SPI unable to use DMA\n");
-		err = -EBUSY;
+		if (err != -EPROBE_DEFER)
+			dev_err(dev, "No TX DMA channel, DMA is disabled\n");
 		goto error_clear;
 	}
 
+	master->dma_rx = dma_request_chan(dev, "rx");
+	if (IS_ERR(master->dma_rx)) {
+		err = PTR_ERR(master->dma_rx);
 		/*
-	 * No reason to check EPROBE_DEFER here since we have already requested
-	 * tx channel. If it fails here, it's for another reason.
+		 * No reason to check EPROBE_DEFER here since we have already
+		 * requested tx channel.
 		 */
-	master->dma_rx = dma_request_slave_channel(dev, "rx");
-
-	if (!master->dma_rx) {
-		dev_err(dev,
-			"DMA RX channel not available, SPI unable to use DMA\n");
-		err = -EBUSY;
+		dev_err(dev, "No RX DMA channel, DMA is disabled\n");
 		goto error;
 	}
 
@@ -548,7 +541,7 @@ static int atmel_spi_configure_dma(struct spi_master *master,
 
 	return 0;
 error:
-	if (master->dma_rx)
+	if (!IS_ERR(master->dma_rx))
 		dma_release_channel(master->dma_rx);
 	if (!IS_ERR(master->dma_tx))
 		dma_release_channel(master->dma_tx);

drivers/spi/spi-bcm-qspi.c

@@ -1293,7 +1293,7 @@ int bcm_qspi_probe(struct platform_device *pdev,
 		name = qspi_irq_tab[val].irq_name;
 		if (qspi_irq_tab[val].irq_source == SINGLE_L2) {
 			/* get the l2 interrupts */
-			irq = platform_get_irq_byname(pdev, name);
+			irq = platform_get_irq_byname_optional(pdev, name);
 		} else if (!num_ints && soc_intc) {
 			/* all mspi, bspi intrs muxed to one L1 intr */
 			irq = platform_get_irq(pdev, 0);

drivers/spi/spi-bcm2835.c

@@ -68,7 +68,7 @@
 #define BCM2835_SPI_FIFO_SIZE		64
 #define BCM2835_SPI_FIFO_SIZE_3_4	48
 #define BCM2835_SPI_DMA_MIN_LENGTH	96
-#define BCM2835_SPI_NUM_CS		3   /* raise as necessary */
+#define BCM2835_SPI_NUM_CS		4   /* raise as necessary */
 #define BCM2835_SPI_MODE_BITS	(SPI_CPOL | SPI_CPHA | SPI_CS_HIGH \
 				| SPI_NO_CS | SPI_3WIRE)
 
@@ -888,7 +888,7 @@ static void bcm2835_dma_release(struct spi_controller *ctlr,
 	}
 }
 
-static void bcm2835_dma_init(struct spi_controller *ctlr, struct device *dev,
+static int bcm2835_dma_init(struct spi_controller *ctlr, struct device *dev,
 			    struct bcm2835_spi *bs)
 {
 	struct dma_slave_config slave_config;
@@ -900,19 +900,24 @@ static void bcm2835_dma_init(struct spi_controller *ctlr, struct device *dev,
 	addr = of_get_address(ctlr->dev.of_node, 0, NULL, NULL);
 	if (!addr) {
 		dev_err(dev, "could not get DMA-register address - not using dma mode\n");
-		goto err;
+		/* Fall back to interrupt mode */
+		return 0;
 	}
 	dma_reg_base = be32_to_cpup(addr);
 
 	/* get tx/rx dma */
-	ctlr->dma_tx = dma_request_slave_channel(dev, "tx");
-	if (!ctlr->dma_tx) {
+	ctlr->dma_tx = dma_request_chan(dev, "tx");
+	if (IS_ERR(ctlr->dma_tx)) {
 		dev_err(dev, "no tx-dma configuration found - not using dma mode\n");
+		ret = PTR_ERR(ctlr->dma_tx);
+		ctlr->dma_tx = NULL;
 		goto err;
 	}
-	ctlr->dma_rx = dma_request_slave_channel(dev, "rx");
-	if (!ctlr->dma_rx) {
+	ctlr->dma_rx = dma_request_chan(dev, "rx");
+	if (IS_ERR(ctlr->dma_rx)) {
 		dev_err(dev, "no rx-dma configuration found - not using dma mode\n");
+		ret = PTR_ERR(ctlr->dma_rx);
+		ctlr->dma_rx = NULL;
 		goto err_release;
 	}
 
@@ -997,7 +1002,7 @@ static void bcm2835_dma_init(struct spi_controller *ctlr, struct device *dev,
 	/* all went well, so set can_dma */
 	ctlr->can_dma = bcm2835_spi_can_dma;
 
-	return;
+	return 0;
 
 err_config:
 	dev_err(dev, "issue configuring dma: %d - not using DMA mode\n",
@@ -1005,7 +1010,14 @@ static void bcm2835_dma_init(struct spi_controller *ctlr, struct device *dev,
 err_release:
 	bcm2835_dma_release(ctlr, bs);
 err:
-	return;
+	/*
+	 * Only report error for deferred probing, otherwise fall back to
+	 * interrupt mode
+	 */
+	if (ret != -EPROBE_DEFER)
+		ret = 0;
+
+	return ret;
 }
 
 static int bcm2835_spi_transfer_one_poll(struct spi_controller *ctlr,
@@ -1305,6 +1317,9 @@ static int bcm2835_spi_probe(struct platform_device *pdev)
 	bs->clk = devm_clk_get(&pdev->dev, NULL);
 	if (IS_ERR(bs->clk)) {
 		err = PTR_ERR(bs->clk);
+		if (err == -EPROBE_DEFER)
+			dev_dbg(&pdev->dev, "could not get clk: %d\n", err);
+		else
 			dev_err(&pdev->dev, "could not get clk: %d\n", err);
 		goto out_controller_put;
 	}
@@ -1317,7 +1332,9 @@ static int bcm2835_spi_probe(struct platform_device *pdev)
 
 	clk_prepare_enable(bs->clk);
 
-	bcm2835_dma_init(ctlr, &pdev->dev, bs);
+	err = bcm2835_dma_init(ctlr, &pdev->dev, bs);
+	if (err)
+		goto out_clk_disable;
 
 	/* initialise the hardware with the default polarities */
 	bcm2835_wr(bs, BCM2835_SPI_CS,
@@ -1327,20 +1344,22 @@ static int bcm2835_spi_probe(struct platform_device *pdev)
 			       dev_name(&pdev->dev), ctlr);
 	if (err) {
 		dev_err(&pdev->dev, "could not request IRQ: %d\n", err);
-		goto out_clk_disable;
+		goto out_dma_release;
 	}
 
 	err = devm_spi_register_controller(&pdev->dev, ctlr);
 	if (err) {
 		dev_err(&pdev->dev, "could not register SPI controller: %d\n",
 			err);
-		goto out_clk_disable;
+		goto out_dma_release;
 	}
 
 	bcm2835_debugfs_create(bs, dev_name(&pdev->dev));
 
 	return 0;
 
+out_dma_release:
+	bcm2835_dma_release(ctlr, bs);
 out_clk_disable:
 	clk_disable_unprepare(bs->clk);
 out_controller_put:

drivers/spi/spi-bitbang.c

@@ -329,8 +329,20 @@ static void spi_bitbang_set_cs(struct spi_device *spi, bool enable)
 int spi_bitbang_init(struct spi_bitbang *bitbang)
 {
 	struct spi_master *master = bitbang->master;
+	bool custom_cs;
 
-	if (!master || !bitbang->chipselect)
+	if (!master)
+		return -EINVAL;
+	/*
+	 * We only need the chipselect callback if we are actually using it.
+	 * If we just use GPIO descriptors, it is surplus. If the
+	 * SPI_MASTER_GPIO_SS flag is set, we always need to call the
+	 * driver-specific chipselect routine.
+	 */
+	custom_cs = (!master->use_gpio_descriptors ||
+		     (master->flags & SPI_MASTER_GPIO_SS));
+
+	if (custom_cs && !bitbang->chipselect)
 		return -EINVAL;
 
 	mutex_init(&bitbang->lock);
@@ -344,6 +356,11 @@ int spi_bitbang_init(struct spi_bitbang *bitbang)
 	master->prepare_transfer_hardware = spi_bitbang_prepare_hardware;
 	master->unprepare_transfer_hardware = spi_bitbang_unprepare_hardware;
 	master->transfer_one = spi_bitbang_transfer_one;
+	/*
+	 * When using GPIO descriptors, the ->set_cs() callback doesn't even
+	 * get called unless SPI_MASTER_GPIO_SS is set.
+	 */
+	if (custom_cs)
 		master->set_cs = spi_bitbang_set_cs;
 
 	if (!bitbang->txrx_bufs) {

drivers/spi/spi-dw.c

@@ -297,6 +297,9 @@ static int dw_spi_transfer_one(struct spi_controller *master,
 	dws->len = transfer->len;
 	spin_unlock_irqrestore(&dws->buf_lock, flags);
 
+	/* Ensure dw->rx and dw->rx_end are visible */
+	smp_mb();
+
 	spi_enable_chip(dws, 0);
 
 	/* Handle per transfer options for bpw and speed */
@@ -469,7 +472,8 @@ int dw_spi_add_host(struct device *dev, struct dw_spi *dws)
 	struct spi_controller *master;
 	int ret;
 
-	BUG_ON(dws == NULL);
+	if (!dws)
+		return -EINVAL;
 
 	master = spi_alloc_master(dev, 0);
 	if (!master)

drivers/spi/spi-fsl-dspi.c

@@ -396,17 +396,17 @@ static int dspi_request_dma(struct fsl_dspi *dspi, phys_addr_t phy_addr)
 	if (!dma)
 		return -ENOMEM;
 
-	dma->chan_rx = dma_request_slave_channel(dev, "rx");
-	if (!dma->chan_rx) {
+	dma->chan_rx = dma_request_chan(dev, "rx");
+	if (IS_ERR(dma->chan_rx)) {
 		dev_err(dev, "rx dma channel not available\n");
-		ret = -ENODEV;
+		ret = PTR_ERR(dma->chan_rx);
 		return ret;
 	}
 
-	dma->chan_tx = dma_request_slave_channel(dev, "tx");
-	if (!dma->chan_tx) {
+	dma->chan_tx = dma_request_chan(dev, "tx");
+	if (IS_ERR(dma->chan_tx)) {
 		dev_err(dev, "tx dma channel not available\n");
-		ret = -ENODEV;
+		ret = PTR_ERR(dma->chan_tx);
 		goto err_tx_channel;
 	}
 

drivers/spi/spi-fsl-lpspi.c

@@ -469,9 +469,9 @@ static int fsl_lpspi_setup_transfer(struct spi_controller *controller,
 		fsl_lpspi->watermark = fsl_lpspi->txfifosize;
 
 	if (fsl_lpspi_can_dma(controller, spi, t))
-		fsl_lpspi->usedma = 1;
+		fsl_lpspi->usedma = true;
 	else
-		fsl_lpspi->usedma = 0;
+		fsl_lpspi->usedma = false;
 
 	return fsl_lpspi_config(fsl_lpspi);
 }
@@ -862,6 +862,22 @@ static int fsl_lpspi_probe(struct platform_device *pdev)
 	fsl_lpspi->dev = &pdev->dev;
 	fsl_lpspi->is_slave = is_slave;
 
+	controller->bits_per_word_mask = SPI_BPW_RANGE_MASK(8, 32);
+	controller->transfer_one = fsl_lpspi_transfer_one;
+	controller->prepare_transfer_hardware = lpspi_prepare_xfer_hardware;
+	controller->unprepare_transfer_hardware = lpspi_unprepare_xfer_hardware;
+	controller->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH;
+	controller->flags = SPI_MASTER_MUST_RX | SPI_MASTER_MUST_TX;
+	controller->dev.of_node = pdev->dev.of_node;
+	controller->bus_num = pdev->id;
+	controller->slave_abort = fsl_lpspi_slave_abort;
+
+	ret = devm_spi_register_controller(&pdev->dev, controller);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "spi_register_controller error.\n");
+		goto out_controller_put;
+	}
+
 	if (!fsl_lpspi->is_slave) {
 		for (i = 0; i < controller->num_chipselect; i++) {
 			int cs_gpio = of_get_named_gpio(np, "cs-gpios", i);
@@ -885,16 +901,6 @@ static int fsl_lpspi_probe(struct platform_device *pdev)
 		controller->prepare_message = fsl_lpspi_prepare_message;
 	}
 
-	controller->bits_per_word_mask = SPI_BPW_RANGE_MASK(8, 32);
-	controller->transfer_one = fsl_lpspi_transfer_one;
-	controller->prepare_transfer_hardware = lpspi_prepare_xfer_hardware;
-	controller->unprepare_transfer_hardware = lpspi_unprepare_xfer_hardware;
-	controller->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH;
-	controller->flags = SPI_MASTER_MUST_RX | SPI_MASTER_MUST_TX;
-	controller->dev.of_node = pdev->dev.of_node;
-	controller->bus_num = pdev->id;
-	controller->slave_abort = fsl_lpspi_slave_abort;
-
 	init_completion(&fsl_lpspi->xfer_done);
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
@@ -952,12 +958,6 @@ static int fsl_lpspi_probe(struct platform_device *pdev)
 	if (ret < 0)
 		dev_err(&pdev->dev, "dma setup error %d, use pio\n", ret);
 
-	ret = devm_spi_register_controller(&pdev->dev, controller);
-	if (ret < 0) {
-		dev_err(&pdev->dev, "spi_register_controller error.\n");
-		goto out_controller_put;
-	}
-
 	return 0;
 
 out_controller_put:

drivers/spi/spi-fsl-qspi.c

@@ -410,7 +410,7 @@ static bool fsl_qspi_supports_op(struct spi_mem *mem,
 	    op->data.nbytes > q->devtype_data->txfifo)
 		return false;
 
-	return true;
+	return spi_mem_default_supports_op(mem, op);
 }
 
 static void fsl_qspi_prepare_lut(struct fsl_qspi *q,

drivers/spi/spi-fsl-spi.c

@@ -706,8 +706,8 @@ static int of_fsl_spi_probe(struct platform_device *ofdev)
 	struct device_node *np = ofdev->dev.of_node;
 	struct spi_master *master;
 	struct resource mem;
-	int irq = 0, type;
-	int ret = -ENOMEM;
+	int irq, type;
+	int ret;
 
 	ret = of_mpc8xxx_spi_probe(ofdev);
 	if (ret)
@@ -722,10 +722,8 @@ static int of_fsl_spi_probe(struct platform_device *ofdev)
 
 		if (spisel_boot) {
 			pinfo->immr_spi_cs = ioremap(get_immrbase() + IMMR_SPI_CS_OFFSET, 4);
-			if (!pinfo->immr_spi_cs) {
-				ret = -ENOMEM;
-				goto err;
-			}
+			if (!pinfo->immr_spi_cs)
+				return -ENOMEM;
 		}
 #endif
 		/*
@@ -744,24 +742,15 @@ static int of_fsl_spi_probe(struct platform_device *ofdev)
 
 	ret = of_address_to_resource(np, 0, &mem);
 	if (ret)
-		goto err;
+		return ret;
 
 	irq = platform_get_irq(ofdev, 0);
-	if (irq < 0) {
-		ret = irq;
-		goto err;
-	}
+	if (irq < 0)
+		return irq;
 
 	master = fsl_spi_probe(dev, &mem, irq);
-	if (IS_ERR(master)) {
-		ret = PTR_ERR(master);
-		goto err;
-	}
-
-	return 0;
 
-err:
-	return ret;
+	return PTR_ERR_OR_ZERO(master);
 }
 
 static int of_fsl_spi_remove(struct platform_device *ofdev)

drivers/spi/spi-hisi-sfc-v3xx.c

+// SPDX-License-Identifier: GPL-2.0-only
+//
+// HiSilicon SPI NOR V3XX Flash Controller Driver for hi16xx chipsets
+//
+// Copyright (c) 2019 HiSilicon Technologies Co., Ltd.
+// Author: John Garry <john.garry@huawei.com>
+
+#include <linux/acpi.h>
+#include <linux/bitops.h>
+#include <linux/iopoll.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/spi-mem.h>
+
+#define HISI_SFC_V3XX_VERSION (0x1f8)
+
+#define HISI_SFC_V3XX_CMD_CFG (0x300)
+#define HISI_SFC_V3XX_CMD_CFG_DATA_CNT_OFF 9
+#define HISI_SFC_V3XX_CMD_CFG_RW_MSK BIT(8)
+#define HISI_SFC_V3XX_CMD_CFG_DATA_EN_MSK BIT(7)
+#define HISI_SFC_V3XX_CMD_CFG_DUMMY_CNT_OFF 4
+#define HISI_SFC_V3XX_CMD_CFG_ADDR_EN_MSK BIT(3)
+#define HISI_SFC_V3XX_CMD_CFG_CS_SEL_OFF 1
+#define HISI_SFC_V3XX_CMD_CFG_START_MSK BIT(0)
+#define HISI_SFC_V3XX_CMD_INS (0x308)
+#define HISI_SFC_V3XX_CMD_ADDR (0x30c)
+#define HISI_SFC_V3XX_CMD_DATABUF0 (0x400)
+
+struct hisi_sfc_v3xx_host {
+	struct device *dev;
+	void __iomem *regbase;
+	int max_cmd_dword;
+};
+
+#define HISI_SFC_V3XX_WAIT_TIMEOUT_US		1000000
+#define HISI_SFC_V3XX_WAIT_POLL_INTERVAL_US	10
+
+static int hisi_sfc_v3xx_wait_cmd_idle(struct hisi_sfc_v3xx_host *host)
+{
+	u32 reg;
+
+	return readl_poll_timeout(host->regbase + HISI_SFC_V3XX_CMD_CFG, reg,
+				  !(reg & HISI_SFC_V3XX_CMD_CFG_START_MSK),
+				  HISI_SFC_V3XX_WAIT_POLL_INTERVAL_US,
+				  HISI_SFC_V3XX_WAIT_TIMEOUT_US);
+}
+
+static int hisi_sfc_v3xx_adjust_op_size(struct spi_mem *mem,
+					struct spi_mem_op *op)
+{
+	struct spi_device *spi = mem->spi;
+	struct hisi_sfc_v3xx_host *host;
+	uintptr_t addr = (uintptr_t)op->data.buf.in;
+	int max_byte_count;
+
+	host = spi_controller_get_devdata(spi->master);
+
+	max_byte_count = host->max_cmd_dword * 4;
+
+	if (!IS_ALIGNED(addr, 4) && op->data.nbytes >= 4)
+		op->data.nbytes = 4 - (addr % 4);
+	else if (op->data.nbytes > max_byte_count)
+		op->data.nbytes = max_byte_count;
+
+	return 0;
+}
+
+/*
+ * memcpy_{to,from}io doesn't gurantee 32b accesses - which we require for the
+ * DATABUF registers -so use __io{read,write}32_copy when possible. For
+ * trailing bytes, copy them byte-by-byte from the DATABUF register, as we
+ * can't clobber outside the source/dest buffer.
+ *
+ * For efficient data read/write, we try to put any start 32b unaligned data
+ * into a separate transaction in hisi_sfc_v3xx_adjust_op_size().
+ */
+static void hisi_sfc_v3xx_read_databuf(struct hisi_sfc_v3xx_host *host,
+				       u8 *to, unsigned int len)
+{
+	void __iomem *from;
+	int i;
+
+	from = host->regbase + HISI_SFC_V3XX_CMD_DATABUF0;
+
+	if (IS_ALIGNED((uintptr_t)to, 4)) {
+		int words = len / 4;
+
+		__ioread32_copy(to, from, words);
+
+		len -= words * 4;
+		if (len) {
+			u32 val;
+
+			to += words * 4;
+			from += words * 4;
+
+			val = __raw_readl(from);
+
+			for (i = 0; i < len; i++, val >>= 8, to++)
+				*to = (u8)val;
+		}
+	} else {
+		for (i = 0; i < DIV_ROUND_UP(len, 4); i++, from += 4) {
+			u32 val = __raw_readl(from);
+			int j;
+
+			for (j = 0; j < 4 && (j + (i * 4) < len);
+			     to++, val >>= 8, j++)
+				*to = (u8)val;
+		}
+	}
+}
+
+static void hisi_sfc_v3xx_write_databuf(struct hisi_sfc_v3xx_host *host,
+					const u8 *from, unsigned int len)
+{
+	void __iomem *to;
+	int i;
+
+	to = host->regbase + HISI_SFC_V3XX_CMD_DATABUF0;
+
+	if (IS_ALIGNED((uintptr_t)from, 4)) {
+		int words = len / 4;
+
+		__iowrite32_copy(to, from, words);
+
+		len -= words * 4;
+		if (len) {
+			u32 val = 0;
+
+			to += words * 4;
+			from += words * 4;
+
+			for (i = 0; i < len; i++, from++)
+				val |= *from << i * 8;
+			__raw_writel(val, to);
+		}
+
+	} else {
+		for (i = 0; i < DIV_ROUND_UP(len, 4); i++, to += 4) {
+			u32 val = 0;
+			int j;
+
+			for (j = 0; j < 4 && (j + (i * 4) < len);
+			     from++, j++)
+				val |= *from << j * 8;
+			__raw_writel(val, to);
+		}
+	}
+}
+
+static int hisi_sfc_v3xx_generic_exec_op(struct hisi_sfc_v3xx_host *host,
+					 const struct spi_mem_op *op,
+					 u8 chip_select)
+{
+	int ret, len = op->data.nbytes;
+	u32 config = 0;
+
+	if (op->addr.nbytes)
+		config |= HISI_SFC_V3XX_CMD_CFG_ADDR_EN_MSK;
+
+	if (op->data.dir != SPI_MEM_NO_DATA) {
+		config |= (len - 1) << HISI_SFC_V3XX_CMD_CFG_DATA_CNT_OFF;
+		config |= HISI_SFC_V3XX_CMD_CFG_DATA_EN_MSK;
+	}
+
+	if (op->data.dir == SPI_MEM_DATA_OUT)
+		hisi_sfc_v3xx_write_databuf(host, op->data.buf.out, len);
+	else if (op->data.dir == SPI_MEM_DATA_IN)
+		config |= HISI_SFC_V3XX_CMD_CFG_RW_MSK;
+
+	config |= op->dummy.nbytes << HISI_SFC_V3XX_CMD_CFG_DUMMY_CNT_OFF |
+		  chip_select << HISI_SFC_V3XX_CMD_CFG_CS_SEL_OFF |
+		  HISI_SFC_V3XX_CMD_CFG_START_MSK;
+
+	writel(op->addr.val, host->regbase + HISI_SFC_V3XX_CMD_ADDR);
+	writel(op->cmd.opcode, host->regbase + HISI_SFC_V3XX_CMD_INS);
+
+	writel(config, host->regbase + HISI_SFC_V3XX_CMD_CFG);
+
+	ret = hisi_sfc_v3xx_wait_cmd_idle(host);
+	if (ret)
+		return ret;
+
+	if (op->data.dir == SPI_MEM_DATA_IN)
+		hisi_sfc_v3xx_read_databuf(host, op->data.buf.in, len);
+
+	return 0;
+}
+
+static int hisi_sfc_v3xx_exec_op(struct spi_mem *mem,
+				 const struct spi_mem_op *op)
+{
+	struct hisi_sfc_v3xx_host *host;
+	struct spi_device *spi = mem->spi;
+	u8 chip_select = spi->chip_select;
+
+	host = spi_controller_get_devdata(spi->master);
+
+	return hisi_sfc_v3xx_generic_exec_op(host, op, chip_select);
+}
+
+static const struct spi_controller_mem_ops hisi_sfc_v3xx_mem_ops = {
+	.adjust_op_size = hisi_sfc_v3xx_adjust_op_size,
+	.exec_op = hisi_sfc_v3xx_exec_op,
+};
+
+static int hisi_sfc_v3xx_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct hisi_sfc_v3xx_host *host;
+	struct spi_controller *ctlr;
+	u32 version;
+	int ret;
+
+	ctlr = spi_alloc_master(&pdev->dev, sizeof(*host));
+	if (!ctlr)
+		return -ENOMEM;
+
+	ctlr->mode_bits = SPI_RX_DUAL | SPI_RX_QUAD |
+			  SPI_TX_DUAL | SPI_TX_QUAD;
+
+	host = spi_controller_get_devdata(ctlr);
+	host->dev = dev;
+
+	platform_set_drvdata(pdev, host);
+
+	host->regbase = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(host->regbase)) {
+		ret = PTR_ERR(host->regbase);
+		goto err_put_master;
+	}
+
+	ctlr->bus_num = -1;
+	ctlr->num_chipselect = 1;
+	ctlr->mem_ops = &hisi_sfc_v3xx_mem_ops;
+
+	version = readl(host->regbase + HISI_SFC_V3XX_VERSION);
+
+	switch (version) {
+	case 0x351:
+		host->max_cmd_dword = 64;
+		break;
+	default:
+		host->max_cmd_dword = 16;
+		break;
+	}
+
+	ret = devm_spi_register_controller(dev, ctlr);
+	if (ret)
+		goto err_put_master;
+
+	dev_info(&pdev->dev, "hw version 0x%x\n", version);
+
+	return 0;
+
+err_put_master:
+	spi_master_put(ctlr);
+	return ret;
+}
+
+#if IS_ENABLED(CONFIG_ACPI)
+static const struct acpi_device_id hisi_sfc_v3xx_acpi_ids[] = {
+	{"HISI0341", 0},
+	{}
+};
+MODULE_DEVICE_TABLE(acpi, hisi_sfc_v3xx_acpi_ids);
+#endif
+
+static struct platform_driver hisi_sfc_v3xx_spi_driver = {
+	.driver = {
+		.name	= "hisi-sfc-v3xx",
+		.acpi_match_table = ACPI_PTR(hisi_sfc_v3xx_acpi_ids),
+	},
+	.probe	= hisi_sfc_v3xx_probe,
+};
+
+module_platform_driver(hisi_sfc_v3xx_spi_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("John Garry <john.garry@huawei.com>");
+MODULE_DESCRIPTION("HiSilicon SPI NOR V3XX Flash Controller Driver for hi16xx chipsets");

drivers/spi/spi-img-spfi.c

@@ -666,8 +666,22 @@ static int img_spfi_probe(struct platform_device *pdev)
 	master->unprepare_message = img_spfi_unprepare;
 	master->handle_err = img_spfi_handle_err;
 
-	spfi->tx_ch = dma_request_slave_channel(spfi->dev, "tx");
-	spfi->rx_ch = dma_request_slave_channel(spfi->dev, "rx");
+	spfi->tx_ch = dma_request_chan(spfi->dev, "tx");
+	if (IS_ERR(spfi->tx_ch)) {
+		ret = PTR_ERR(spfi->tx_ch);
+		spfi->tx_ch = NULL;
+		if (ret == -EPROBE_DEFER)
+			goto disable_pm;
+	}
+
+	spfi->rx_ch = dma_request_chan(spfi->dev, "rx");
+	if (IS_ERR(spfi->rx_ch)) {
+		ret = PTR_ERR(spfi->rx_ch);
+		spfi->rx_ch = NULL;
+		if (ret == -EPROBE_DEFER)
+			goto disable_pm;
+	}
+
 	if (!spfi->tx_ch || !spfi->rx_ch) {
 		if (spfi->tx_ch)
 			dma_release_channel(spfi->tx_ch);

drivers/spi/spi-imx.c

@@ -1230,9 +1230,9 @@ static int spi_imx_setupxfer(struct spi_device *spi,
 	}
 
 	if (spi_imx_can_dma(spi_imx->bitbang.master, spi, t))
-		spi_imx->usedma = 1;
+		spi_imx->usedma = true;
 	else
-		spi_imx->usedma = 0;
+		spi_imx->usedma = false;
 
 	if (is_imx53_ecspi(spi_imx) && spi_imx->slave_mode) {
 		spi_imx->rx = mx53_ecspi_rx_slave;

drivers/spi/spi-meson-spicc.c

@@ -19,7 +19,6 @@
 #include <linux/types.h>
 #include <linux/interrupt.h>
 #include <linux/reset.h>
-#include <linux/gpio.h>
 
 /*
  * The Meson SPICC controller could support DMA based transfers, but is not
@@ -467,35 +466,14 @@ static int meson_spicc_unprepare_transfer(struct spi_master *master)
 
 static int meson_spicc_setup(struct spi_device *spi)
 {
-	int ret = 0;
-
 	if (!spi->controller_state)
 		spi->controller_state = spi_master_get_devdata(spi->master);
-	else if (gpio_is_valid(spi->cs_gpio))
-		goto out_gpio;
-	else if (spi->cs_gpio == -ENOENT)
-		return 0;
 
-	if (gpio_is_valid(spi->cs_gpio)) {
-		ret = gpio_request(spi->cs_gpio, dev_name(&spi->dev));
-		if (ret) {
-			dev_err(&spi->dev, "failed to request cs gpio\n");
-			return ret;
-		}
-	}
-
-out_gpio:
-	ret = gpio_direction_output(spi->cs_gpio,
-			!(spi->mode & SPI_CS_HIGH));
-
-	return ret;
+	return 0;
 }
 
 static void meson_spicc_cleanup(struct spi_device *spi)
 {
-	if (gpio_is_valid(spi->cs_gpio))
-		gpio_free(spi->cs_gpio);
-
 	spi->controller_state = NULL;
 }
 
@@ -564,6 +542,7 @@ static int meson_spicc_probe(struct platform_device *pdev)
 	master->prepare_message = meson_spicc_prepare_message;
 	master->unprepare_transfer_hardware = meson_spicc_unprepare_transfer;
 	master->transfer_one = meson_spicc_transfer_one;
+	master->use_gpio_descriptors = true;
 
 	/* Setup max rate according to the Meson GX datasheet */
 	if ((rate >> 2) > SPICC_MAX_FREQ)

drivers/spi/spi-mxs.c

@@ -590,10 +590,10 @@ static int mxs_spi_probe(struct platform_device *pdev)
 	if (ret)
 		goto out_master_free;
 
-	ssp->dmach = dma_request_slave_channel(&pdev->dev, "rx-tx");
-	if (!ssp->dmach) {
+	ssp->dmach = dma_request_chan(&pdev->dev, "rx-tx");
+	if (IS_ERR(ssp->dmach)) {
 		dev_err(ssp->dev, "Failed to request DMA\n");
-		ret = -ENODEV;
+		ret = PTR_ERR(ssp->dmach);
 		goto out_master_free;
 	}
 

drivers/spi/spi-npcm-pspi.c

@@ -12,6 +12,7 @@
 #include <linux/spi/spi.h>
 #include <linux/gpio.h>
 #include <linux/of_gpio.h>
+#include <linux/reset.h>
 
 #include <asm/unaligned.h>
 
@@ -20,7 +21,7 @@
 
 struct npcm_pspi {
 	struct completion xfer_done;
-	struct regmap *rst_regmap;
+	struct reset_control *reset;
 	struct spi_master *master;
 	unsigned int tx_bytes;
 	unsigned int rx_bytes;
@@ -59,12 +60,6 @@ struct npcm_pspi {
 #define NPCM_PSPI_MIN_CLK_DIVIDER	4
 #define NPCM_PSPI_DEFAULT_CLK		25000000
 
-/* reset register */
-#define NPCM7XX_IPSRST2_OFFSET	0x24
-
-#define NPCM7XX_PSPI1_RESET	BIT(22)
-#define NPCM7XX_PSPI2_RESET	BIT(23)
-
 static inline unsigned int bytes_per_word(unsigned int bits)
 {
 	return bits <= 8 ? 1 : 2;
@@ -178,6 +173,13 @@ static void npcm_pspi_setup_transfer(struct spi_device *spi,
 		priv->mode = spi->mode;
 	}
 
+	/*
+	 * If transfer is even length, and 8 bits per word transfer,
+	 * then implement 16 bits-per-word transfer.
+	 */
+	if (priv->bits_per_word == 8 && !(t->len & 0x1))
+		t->bits_per_word = 16;
+
 	if (!priv->is_save_param || priv->bits_per_word != t->bits_per_word) {
 		npcm_pspi_set_transfer_size(priv, t->bits_per_word);
 		priv->bits_per_word = t->bits_per_word;
@@ -195,6 +197,7 @@ static void npcm_pspi_setup_transfer(struct spi_device *spi,
 static void npcm_pspi_send(struct npcm_pspi *priv)
 {
 	int wsize;
+	u16 val;
 
 	wsize = min(bytes_per_word(priv->bits_per_word), priv->tx_bytes);
 	priv->tx_bytes -= wsize;
@@ -204,17 +207,18 @@ static void npcm_pspi_send(struct npcm_pspi *priv)
 
 	switch (wsize) {
 	case 1:
-		iowrite8(*priv->tx_buf, NPCM_PSPI_DATA + priv->base);
+		val = *priv->tx_buf++;
+		iowrite8(val, NPCM_PSPI_DATA + priv->base);
 		break;
 	case 2:
-		iowrite16(*priv->tx_buf, NPCM_PSPI_DATA + priv->base);
+		val = *priv->tx_buf++;
+		val = *priv->tx_buf++ | (val << 8);
+		iowrite16(val, NPCM_PSPI_DATA + priv->base);
 		break;
 	default:
 		WARN_ON_ONCE(1);
 		return;
 	}
-
-	priv->tx_buf += wsize;
 }
 
 static void npcm_pspi_recv(struct npcm_pspi *priv)
@@ -230,18 +234,17 @@ static void npcm_pspi_recv(struct npcm_pspi *priv)
 
 	switch (rsize) {
 	case 1:
-		val = ioread8(priv->base + NPCM_PSPI_DATA);
+		*priv->rx_buf++ = ioread8(priv->base + NPCM_PSPI_DATA);
 		break;
 	case 2:
 		val = ioread16(priv->base + NPCM_PSPI_DATA);
+		*priv->rx_buf++ = (val >> 8);
+		*priv->rx_buf++ = val & 0xff;
 		break;
 	default:
 		WARN_ON_ONCE(1);
 		return;
 	}
-
-	*priv->rx_buf = val;
-	priv->rx_buf += rsize;
 }
 
 static int npcm_pspi_transfer_one(struct spi_master *master,
@@ -285,9 +288,9 @@ static int npcm_pspi_unprepare_transfer_hardware(struct spi_master *master)
 
 static void npcm_pspi_reset_hw(struct npcm_pspi *priv)
 {
-	regmap_write(priv->rst_regmap, NPCM7XX_IPSRST2_OFFSET,
-		     NPCM7XX_PSPI1_RESET << priv->id);
-	regmap_write(priv->rst_regmap, NPCM7XX_IPSRST2_OFFSET, 0x0);
+	reset_control_assert(priv->reset);
+	udelay(5);
+	reset_control_deassert(priv->reset);
 }
 
 static irqreturn_t npcm_pspi_handler(int irq, void *dev_id)
@@ -351,10 +354,6 @@ static int npcm_pspi_probe(struct platform_device *pdev)
 	if (num_cs < 0)
 		return num_cs;
 
-	pdev->id = of_alias_get_id(np, "spi");
-	if (pdev->id < 0)
-		pdev->id = 0;
-
 	master = spi_alloc_master(&pdev->dev, sizeof(*priv));
 	if (!master)
 		return -ENOMEM;
@@ -364,7 +363,6 @@ static int npcm_pspi_probe(struct platform_device *pdev)
 	priv = spi_master_get_devdata(master);
 	priv->master = master;
 	priv->is_save_param = false;
-	priv->id = pdev->id;
 
 	priv->base = devm_platform_ioremap_resource(pdev, 0);
 	if (IS_ERR(priv->base)) {
@@ -389,11 +387,10 @@ static int npcm_pspi_probe(struct platform_device *pdev)
 		goto out_disable_clk;
 	}
 
-	priv->rst_regmap =
-		syscon_regmap_lookup_by_compatible("nuvoton,npcm750-rst");
-	if (IS_ERR(priv->rst_regmap)) {
-		dev_err(&pdev->dev, "failed to find nuvoton,npcm750-rst\n");
-		return PTR_ERR(priv->rst_regmap);
+	priv->reset = devm_reset_control_get(&pdev->dev, NULL);
+	if (IS_ERR(priv->reset)) {
+		ret = PTR_ERR(priv->reset);
+		goto out_disable_clk;
 	}
 
 	/* reset SPI-HW block */
@@ -414,7 +411,7 @@ static int npcm_pspi_probe(struct platform_device *pdev)
 	master->min_speed_hz = DIV_ROUND_UP(clk_hz, NPCM_PSPI_MAX_CLK_DIVIDER);
 	master->mode_bits = SPI_CPHA | SPI_CPOL;
 	master->dev.of_node = pdev->dev.of_node;
-	master->bus_num = pdev->id;
+	master->bus_num = -1;
 	master->bits_per_word_mask = SPI_BPW_MASK(8) | SPI_BPW_MASK(16);
 	master->transfer_one = npcm_pspi_transfer_one;
 	master->prepare_transfer_hardware =
@@ -447,7 +444,7 @@ static int npcm_pspi_probe(struct platform_device *pdev)
 	if (ret)
 		goto out_disable_clk;
 
-	pr_info("NPCM Peripheral SPI %d probed\n", pdev->id);
+	pr_info("NPCM Peripheral SPI %d probed\n", master->bus_num);
 
 	return 0;
 

drivers/spi/spi-oc-tiny.c

@@ -20,7 +20,6 @@
 #include <linux/spi/spi_bitbang.h>
 #include <linux/spi/spi_oc_tiny.h>
 #include <linux/io.h>
-#include <linux/gpio.h>
 #include <linux/of.h>
 
 #define DRV_NAME "spi_oc_tiny"
@@ -50,8 +49,6 @@ struct tiny_spi {
 	unsigned int txc, rxc;
 	const u8 *txp;
 	u8 *rxp;
-	int gpio_cs_count;
-	int *gpio_cs;
 };
 
 static inline struct tiny_spi *tiny_spi_to_hw(struct spi_device *sdev)
@@ -66,16 +63,6 @@ static unsigned int tiny_spi_baud(struct spi_device *spi, unsigned int hz)
 	return min(DIV_ROUND_UP(hw->freq, hz * 2), (1U << hw->baudwidth)) - 1;
 }
 
-static void tiny_spi_chipselect(struct spi_device *spi, int is_active)
-{
-	struct tiny_spi *hw = tiny_spi_to_hw(spi);
-
-	if (hw->gpio_cs_count > 0) {
-		gpio_set_value(hw->gpio_cs[spi->chip_select],
-			(spi->mode & SPI_CS_HIGH) ? is_active : !is_active);
-	}
-}
-
 static int tiny_spi_setup_transfer(struct spi_device *spi,
 				   struct spi_transfer *t)
 {
@@ -203,24 +190,10 @@ static int tiny_spi_of_probe(struct platform_device *pdev)
 {
 	struct tiny_spi *hw = platform_get_drvdata(pdev);
 	struct device_node *np = pdev->dev.of_node;
-	unsigned int i;
 	u32 val;
 
 	if (!np)
 		return 0;
-	hw->gpio_cs_count = of_gpio_count(np);
-	if (hw->gpio_cs_count > 0) {
-		hw->gpio_cs = devm_kcalloc(&pdev->dev,
-				hw->gpio_cs_count, sizeof(unsigned int),
-				GFP_KERNEL);
-		if (!hw->gpio_cs)
-			return -ENOMEM;
-	}
-	for (i = 0; i < hw->gpio_cs_count; i++) {
-		hw->gpio_cs[i] = of_get_gpio_flags(np, i, NULL);
-		if (hw->gpio_cs[i] < 0)
-			return -ENODEV;
-	}
 	hw->bitbang.master->dev.of_node = pdev->dev.of_node;
 	if (!of_property_read_u32(np, "clock-frequency", &val))
 		hw->freq = val;
@@ -240,7 +213,6 @@ static int tiny_spi_probe(struct platform_device *pdev)
 	struct tiny_spi_platform_data *platp = dev_get_platdata(&pdev->dev);
 	struct tiny_spi *hw;
 	struct spi_master *master;
-	unsigned int i;
 	int err = -ENODEV;
 
 	master = spi_alloc_master(&pdev->dev, sizeof(struct tiny_spi));
@@ -249,9 +221,9 @@ static int tiny_spi_probe(struct platform_device *pdev)
 
 	/* setup the master state. */
 	master->bus_num = pdev->id;
-	master->num_chipselect = 255;
 	master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH;
 	master->setup = tiny_spi_setup;
+	master->use_gpio_descriptors = true;
 
 	hw = spi_master_get_devdata(master);
 	platform_set_drvdata(pdev, hw);
@@ -259,7 +231,6 @@ static int tiny_spi_probe(struct platform_device *pdev)
 	/* setup the state for the bitbang driver */
 	hw->bitbang.master = master;
 	hw->bitbang.setup_transfer = tiny_spi_setup_transfer;
-	hw->bitbang.chipselect = tiny_spi_chipselect;
 	hw->bitbang.txrx_bufs = tiny_spi_txrx_bufs;
 
 	/* find and map our resources */
@@ -279,12 +250,6 @@ static int tiny_spi_probe(struct platform_device *pdev)
 	}
 	/* find platform data */
 	if (platp) {
-		hw->gpio_cs_count = platp->gpio_cs_count;
-		hw->gpio_cs = platp->gpio_cs;
-		if (platp->gpio_cs_count && !platp->gpio_cs) {
-			err = -EBUSY;
-			goto exit;
-		}
 		hw->freq = platp->freq;
 		hw->baudwidth = platp->baudwidth;
 	} else {
@@ -292,13 +257,6 @@ static int tiny_spi_probe(struct platform_device *pdev)
 		if (err)
 			goto exit;
 	}
-	for (i = 0; i < hw->gpio_cs_count; i++) {
-		err = gpio_request(hw->gpio_cs[i], dev_name(&pdev->dev));
-		if (err)
-			goto exit_gpio;
-		gpio_direction_output(hw->gpio_cs[i], 1);
-	}
-	hw->bitbang.master->num_chipselect = max(1, hw->gpio_cs_count);
 
 	/* register our spi controller */
 	err = spi_bitbang_start(&hw->bitbang);
@@ -308,9 +266,6 @@ static int tiny_spi_probe(struct platform_device *pdev)
 
 	return 0;
 
-exit_gpio:
-	while (i-- > 0)
-		gpio_free(hw->gpio_cs[i]);
 exit:
 	spi_master_put(master);
 	return err;
@@ -320,11 +275,8 @@ static int tiny_spi_remove(struct platform_device *pdev)
 {
 	struct tiny_spi *hw = platform_get_drvdata(pdev);
 	struct spi_master *master = hw->bitbang.master;
-	unsigned int i;
 
 	spi_bitbang_stop(&hw->bitbang);
-	for (i = 0; i < hw->gpio_cs_count; i++)
-		gpio_free(hw->gpio_cs[i]);
 	spi_master_put(master);
 	return 0;
 }

drivers/spi/spi-pxa2xx.c

@@ -461,6 +461,16 @@ int pxa2xx_spi_flush(struct driver_data *drv_data)
 	return limit;
 }
 
+static void pxa2xx_spi_off(struct driver_data *drv_data)
+{
+	/* On MMP, disabling SSE seems to corrupt the rx fifo */
+	if (drv_data->ssp_type == MMP2_SSP)
+		return;
+
+	pxa2xx_spi_write(drv_data, SSCR0,
+			 pxa2xx_spi_read(drv_data, SSCR0) & ~SSCR0_SSE);
+}
+
 static int null_writer(struct driver_data *drv_data)
 {
 	u8 n_bytes = drv_data->n_bytes;
@@ -587,8 +597,7 @@ static void int_error_stop(struct driver_data *drv_data, const char* msg)
 	if (!pxa25x_ssp_comp(drv_data))
 		pxa2xx_spi_write(drv_data, SSTO, 0);
 	pxa2xx_spi_flush(drv_data);
-	pxa2xx_spi_write(drv_data, SSCR0,
-			 pxa2xx_spi_read(drv_data, SSCR0) & ~SSCR0_SSE);
+	pxa2xx_spi_off(drv_data);
 
 	dev_err(&drv_data->pdev->dev, "%s\n", msg);
 
@@ -686,8 +695,7 @@ static irqreturn_t interrupt_transfer(struct driver_data *drv_data)
 
 static void handle_bad_msg(struct driver_data *drv_data)
 {
-	pxa2xx_spi_write(drv_data, SSCR0,
-			 pxa2xx_spi_read(drv_data, SSCR0) & ~SSCR0_SSE);
+	pxa2xx_spi_off(drv_data);
 	pxa2xx_spi_write(drv_data, SSCR1,
 			 pxa2xx_spi_read(drv_data, SSCR1) & ~drv_data->int_cr1);
 	if (!pxa25x_ssp_comp(drv_data))
@@ -1062,6 +1070,7 @@ static int pxa2xx_spi_transfer_one(struct spi_controller *controller,
 	    || (pxa2xx_spi_read(drv_data, SSCR1) & change_mask)
 	    != (cr1 & change_mask)) {
 		/* stop the SSP, and update the other bits */
+		if (drv_data->ssp_type != MMP2_SSP)
 			pxa2xx_spi_write(drv_data, SSCR0, cr0 & ~SSCR0_SSE);
 		if (!pxa25x_ssp_comp(drv_data))
 			pxa2xx_spi_write(drv_data, SSTO, chip->timeout);
@@ -1118,8 +1127,7 @@ static int pxa2xx_spi_slave_abort(struct spi_controller *controller)
 	if (!pxa25x_ssp_comp(drv_data))
 		pxa2xx_spi_write(drv_data, SSTO, 0);
 	pxa2xx_spi_flush(drv_data);
-	pxa2xx_spi_write(drv_data, SSCR0,
-			 pxa2xx_spi_read(drv_data, SSCR0) & ~SSCR0_SSE);
+	pxa2xx_spi_off(drv_data);
 
 	dev_dbg(&drv_data->pdev->dev, "transfer aborted\n");
 
@@ -1135,8 +1143,7 @@ static void pxa2xx_spi_handle_err(struct spi_controller *controller,
 	struct driver_data *drv_data = spi_controller_get_devdata(controller);
 
 	/* Disable the SSP */
-	pxa2xx_spi_write(drv_data, SSCR0,
-			 pxa2xx_spi_read(drv_data, SSCR0) & ~SSCR0_SSE);
+	pxa2xx_spi_off(drv_data);
 	/* Clear and disable interrupts and service requests */
 	write_SSSR_CS(drv_data, drv_data->clear_sr);
 	pxa2xx_spi_write(drv_data, SSCR1,
@@ -1161,8 +1168,7 @@ static int pxa2xx_spi_unprepare_transfer(struct spi_controller *controller)
 	struct driver_data *drv_data = spi_controller_get_devdata(controller);
 
 	/* Disable the SSP now */
-	pxa2xx_spi_write(drv_data, SSCR0,
-			 pxa2xx_spi_read(drv_data, SSCR0) & ~SSCR0_SSE);
+	pxa2xx_spi_off(drv_data);
 
 	return 0;
 }
@@ -1423,6 +1429,9 @@ static const struct pci_device_id pxa2xx_spi_pci_compound_match[] = {
 	/* KBL-H */
 	{ PCI_VDEVICE(INTEL, 0xa2a9), LPSS_SPT_SSP },
 	{ PCI_VDEVICE(INTEL, 0xa2aa), LPSS_SPT_SSP },
+	/* CML-V */
+	{ PCI_VDEVICE(INTEL, 0xa3a9), LPSS_SPT_SSP },
+	{ PCI_VDEVICE(INTEL, 0xa3aa), LPSS_SPT_SSP },
 	/* BXT A-Step */
 	{ PCI_VDEVICE(INTEL, 0x0ac2), LPSS_BXT_SSP },
 	{ PCI_VDEVICE(INTEL, 0x0ac4), LPSS_BXT_SSP },

drivers/spi/spi-qcom-qspi.c

@@ -137,7 +137,7 @@ enum qspi_clocks {
 struct qcom_qspi {
 	void __iomem *base;
 	struct device *dev;
-	struct clk_bulk_data clks[QSPI_NUM_CLKS];
+	struct clk_bulk_data *clks;
 	struct qspi_xfer xfer;
 	/* Lock to protect xfer and IRQ accessed registers */
 	spinlock_t lock;
@@ -445,6 +445,13 @@ static int qcom_qspi_probe(struct platform_device *pdev)
 		goto exit_probe_master_put;
 	}
 
+	ctrl->clks = devm_kcalloc(dev, QSPI_NUM_CLKS,
+				  sizeof(*ctrl->clks), GFP_KERNEL);
+	if (!ctrl->clks) {
+		ret = -ENOMEM;
+		goto exit_probe_master_put;
+	}
+
 	ctrl->clks[QSPI_CLK_CORE].id = "core";
 	ctrl->clks[QSPI_CLK_IFACE].id = "iface";
 	ret = devm_clk_bulk_get(dev, QSPI_NUM_CLKS, ctrl->clks);

drivers/spi/spi-rspi.c

@@ -159,7 +159,7 @@
 #define SPCMD_SPIMOD_DUAL	SPCMD_SPIMOD0
 #define SPCMD_SPIMOD_QUAD	SPCMD_SPIMOD1
 #define SPCMD_SPRW		0x0010	/* SPI Read/Write Access (Dual/Quad) */
-#define SPCMD_SSLA_MASK		0x0030	/* SSL Assert Signal Setting (RSPI) */
+#define SPCMD_SSLA(i)		((i) << 4)	/* SSL Assert Signal Setting */
 #define SPCMD_BRDV_MASK		0x000c	/* Bit Rate Division Setting */
 #define SPCMD_CPOL		0x0002	/* Clock Polarity Setting */
 #define SPCMD_CPHA		0x0001	/* Clock Phase Setting */
@@ -242,6 +242,7 @@ struct spi_ops {
 	u16 mode_bits;
 	u16 flags;
 	u16 fifo_size;
+	u8 num_hw_ss;
 };
 
 /*
@@ -426,8 +427,6 @@ static int qspi_set_receive_trigger(struct rspi_data *rspi, unsigned int len)
 	return n;
 }
 
-#define set_config_register(spi, n) spi->ops->set_config_register(spi, n)
-
 static void rspi_enable_irq(const struct rspi_data *rspi, u8 enable)
 {
 	rspi_write8(rspi, rspi_read8(rspi, RSPI_SPCR) | enable, RSPI_SPCR);
@@ -620,9 +619,8 @@ static int rspi_dma_transfer(struct rspi_data *rspi, struct sg_table *tx,
 		dmaengine_terminate_all(rspi->ctlr->dma_rx);
 no_dma_rx:
 	if (ret == -EAGAIN) {
-		pr_warn_once("%s %s: DMA not available, falling back to PIO\n",
-			     dev_driver_string(&rspi->ctlr->dev),
-			     dev_name(&rspi->ctlr->dev));
+		dev_warn_once(&rspi->ctlr->dev,
+			      "DMA not available, falling back to PIO\n");
 	}
 	return ret;
 }
@@ -936,12 +934,16 @@ static int rspi_prepare_message(struct spi_controller *ctlr,
 	if (spi->mode & SPI_CPHA)
 		rspi->spcmd |= SPCMD_CPHA;
 
+	/* Configure slave signal to assert */
+	rspi->spcmd |= SPCMD_SSLA(spi->cs_gpiod ? rspi->ctlr->unused_native_cs
+						: spi->chip_select);
+
 	/* CMOS output mode and MOSI signal from previous transfer */
 	rspi->sppcr = 0;
 	if (spi->mode & SPI_LOOP)
 		rspi->sppcr |= SPPCR_SPLP;
 
-	set_config_register(rspi, 8);
+	rspi->ops->set_config_register(rspi, 8);
 
 	if (msg->spi->mode &
 	    (SPI_TX_DUAL | SPI_TX_QUAD | SPI_RX_DUAL | SPI_RX_QUAD)) {
@@ -1123,6 +1125,7 @@ static const struct spi_ops rspi_ops = {
 	.mode_bits =		SPI_CPHA | SPI_CPOL | SPI_LOOP,
 	.flags =		SPI_CONTROLLER_MUST_TX,
 	.fifo_size =		8,
+	.num_hw_ss =		2,
 };
 
 static const struct spi_ops rspi_rz_ops = {
@@ -1131,6 +1134,7 @@ static const struct spi_ops rspi_rz_ops = {
 	.mode_bits =		SPI_CPHA | SPI_CPOL | SPI_LOOP,
 	.flags =		SPI_CONTROLLER_MUST_RX | SPI_CONTROLLER_MUST_TX,
 	.fifo_size =		8,	/* 8 for TX, 32 for RX */
+	.num_hw_ss =		1,
 };
 
 static const struct spi_ops qspi_ops = {
@@ -1141,6 +1145,7 @@ static const struct spi_ops qspi_ops = {
 				SPI_RX_DUAL | SPI_RX_QUAD,
 	.flags =		SPI_CONTROLLER_MUST_RX | SPI_CONTROLLER_MUST_TX,
 	.fifo_size =		32,
+	.num_hw_ss =		1,
 };
 
 #ifdef CONFIG_OF
@@ -1256,6 +1261,8 @@ static int rspi_probe(struct platform_device *pdev)
 	ctlr->mode_bits = ops->mode_bits;
 	ctlr->flags = ops->flags;
 	ctlr->dev.of_node = pdev->dev.of_node;
+	ctlr->use_gpio_descriptors = true;
+	ctlr->max_native_cs = rspi->ops->num_hw_ss;
 
 	ret = platform_get_irq_byname_optional(pdev, "rx");
 	if (ret < 0) {
@@ -1314,8 +1321,6 @@ static int rspi_probe(struct platform_device *pdev)
 
 static const struct platform_device_id spi_driver_ids[] = {
 	{ "rspi",	(kernel_ulong_t)&rspi_ops },
-	{ "rspi-rz",	(kernel_ulong_t)&rspi_rz_ops },
-	{ "qspi",	(kernel_ulong_t)&qspi_ops },
 	{},
 };
 

drivers/spi/spi-sirf.c

@@ -1126,16 +1126,16 @@ static int spi_sirfsoc_probe(struct platform_device *pdev)
 	sspi->bitbang.master->dev.of_node = pdev->dev.of_node;
 
 	/* request DMA channels */
-	sspi->rx_chan = dma_request_slave_channel(&pdev->dev, "rx");
-	if (!sspi->rx_chan) {
+	sspi->rx_chan = dma_request_chan(&pdev->dev, "rx");
+	if (IS_ERR(sspi->rx_chan)) {
 		dev_err(&pdev->dev, "can not allocate rx dma channel\n");
-		ret = -ENODEV;
+		ret = PTR_ERR(sspi->rx_chan);
 		goto free_master;
 	}
-	sspi->tx_chan = dma_request_slave_channel(&pdev->dev, "tx");
-	if (!sspi->tx_chan) {
+	sspi->tx_chan = dma_request_chan(&pdev->dev, "tx");
+	if (IS_ERR(sspi->tx_chan)) {
 		dev_err(&pdev->dev, "can not allocate tx dma channel\n");
-		ret = -ENODEV;
+		ret = PTR_ERR(sspi->tx_chan);
 		goto free_rx_dma;
 	}
 

drivers/spi/spi-stm32-qspi.c

@@ -470,10 +470,11 @@ static int stm32_qspi_setup(struct spi_device *spi)
 	return 0;
 }
 
-static void stm32_qspi_dma_setup(struct stm32_qspi *qspi)
+static int stm32_qspi_dma_setup(struct stm32_qspi *qspi)
 {
 	struct dma_slave_config dma_cfg;
 	struct device *dev = qspi->dev;
+	int ret = 0;
 
 	memset(&dma_cfg, 0, sizeof(dma_cfg));
 
@@ -484,8 +485,13 @@ static void stm32_qspi_dma_setup(struct stm32_qspi *qspi)
 	dma_cfg.src_maxburst = 4;
 	dma_cfg.dst_maxburst = 4;
 
-	qspi->dma_chrx = dma_request_slave_channel(dev, "rx");
-	if (qspi->dma_chrx) {
+	qspi->dma_chrx = dma_request_chan(dev, "rx");
+	if (IS_ERR(qspi->dma_chrx)) {
+		ret = PTR_ERR(qspi->dma_chrx);
+		qspi->dma_chrx = NULL;
+		if (ret == -EPROBE_DEFER)
+			goto out;
+	} else {
 		if (dmaengine_slave_config(qspi->dma_chrx, &dma_cfg)) {
 			dev_err(dev, "dma rx config failed\n");
 			dma_release_channel(qspi->dma_chrx);
@@ -493,8 +499,11 @@ static void stm32_qspi_dma_setup(struct stm32_qspi *qspi)
 		}
 	}
 
-	qspi->dma_chtx = dma_request_slave_channel(dev, "tx");
-	if (qspi->dma_chtx) {
+	qspi->dma_chtx = dma_request_chan(dev, "tx");
+	if (IS_ERR(qspi->dma_chtx)) {
+		ret = PTR_ERR(qspi->dma_chtx);
+		qspi->dma_chtx = NULL;
+	} else {
 		if (dmaengine_slave_config(qspi->dma_chtx, &dma_cfg)) {
 			dev_err(dev, "dma tx config failed\n");
 			dma_release_channel(qspi->dma_chtx);
@@ -502,7 +511,13 @@ static void stm32_qspi_dma_setup(struct stm32_qspi *qspi)
 		}
 	}
 
+out:
 	init_completion(&qspi->dma_completion);
+
+	if (ret != -EPROBE_DEFER)
+		ret = 0;
+
+	return ret;
 }
 
 static void stm32_qspi_dma_free(struct stm32_qspi *qspi)
@@ -608,7 +623,10 @@ static int stm32_qspi_probe(struct platform_device *pdev)
 
 	qspi->dev = dev;
 	platform_set_drvdata(pdev, qspi);
-	stm32_qspi_dma_setup(qspi);
+	ret = stm32_qspi_dma_setup(qspi);
+	if (ret)
+		goto err;
+
 	mutex_init(&qspi->lock);
 
 	ctrl->mode_bits = SPI_RX_DUAL | SPI_RX_QUAD

drivers/spi/spi-stm32.c

@@ -9,7 +9,6 @@
 #include <linux/clk.h>
 #include <linux/delay.h>
 #include <linux/dmaengine.h>
-#include <linux/gpio.h>
 #include <linux/interrupt.h>
 #include <linux/iopoll.h>
 #include <linux/module.h>
@@ -973,29 +972,6 @@ static irqreturn_t stm32h7_spi_irq_thread(int irq, void *dev_id)
 	return IRQ_HANDLED;
 }
 
-/**
- * stm32_spi_setup - setup device chip select
- */
-static int stm32_spi_setup(struct spi_device *spi_dev)
-{
-	int ret = 0;
-
-	if (!gpio_is_valid(spi_dev->cs_gpio)) {
-		dev_err(&spi_dev->dev, "%d is not a valid gpio\n",
-			spi_dev->cs_gpio);
-		return -EINVAL;
-	}
-
-	dev_dbg(&spi_dev->dev, "%s: set gpio%d output %s\n", __func__,
-		spi_dev->cs_gpio,
-		(spi_dev->mode & SPI_CS_HIGH) ? "low" : "high");
-
-	ret = gpio_direction_output(spi_dev->cs_gpio,
-				    !(spi_dev->mode & SPI_CS_HIGH));
-
-	return ret;
-}
-
 /**
  * stm32_spi_prepare_msg - set up the controller to transfer a single message
  */
@@ -1810,7 +1786,7 @@ static int stm32_spi_probe(struct platform_device *pdev)
 	struct spi_master *master;
 	struct stm32_spi *spi;
 	struct resource *res;
-	int i, ret;
+	int ret;
 
 	master = spi_alloc_master(&pdev->dev, sizeof(struct stm32_spi));
 	if (!master) {
@@ -1898,22 +1874,34 @@ static int stm32_spi_probe(struct platform_device *pdev)
 	master->bits_per_word_mask = spi->cfg->get_bpw_mask(spi);
 	master->max_speed_hz = spi->clk_rate / spi->cfg->baud_rate_div_min;
 	master->min_speed_hz = spi->clk_rate / spi->cfg->baud_rate_div_max;
-	master->setup = stm32_spi_setup;
+	master->use_gpio_descriptors = true;
 	master->prepare_message = stm32_spi_prepare_msg;
 	master->transfer_one = stm32_spi_transfer_one;
 	master->unprepare_message = stm32_spi_unprepare_msg;
 
-	spi->dma_tx = dma_request_slave_channel(spi->dev, "tx");
-	if (!spi->dma_tx)
+	spi->dma_tx = dma_request_chan(spi->dev, "tx");
+	if (IS_ERR(spi->dma_tx)) {
+		ret = PTR_ERR(spi->dma_tx);
+		spi->dma_tx = NULL;
+		if (ret == -EPROBE_DEFER)
+			goto err_clk_disable;
+
 		dev_warn(&pdev->dev, "failed to request tx dma channel\n");
-	else
+	} else {
 		master->dma_tx = spi->dma_tx;
+	}
+
+	spi->dma_rx = dma_request_chan(spi->dev, "rx");
+	if (IS_ERR(spi->dma_rx)) {
+		ret = PTR_ERR(spi->dma_rx);
+		spi->dma_rx = NULL;
+		if (ret == -EPROBE_DEFER)
+			goto err_dma_release;
 
-	spi->dma_rx = dma_request_slave_channel(spi->dev, "rx");
-	if (!spi->dma_rx)
 		dev_warn(&pdev->dev, "failed to request rx dma channel\n");
-	else
+	} else {
 		master->dma_rx = spi->dma_rx;
+	}
 
 	if (spi->dma_tx || spi->dma_rx)
 		master->can_dma = stm32_spi_can_dma;
@@ -1925,43 +1913,26 @@ static int stm32_spi_probe(struct platform_device *pdev)
 	if (ret) {
 		dev_err(&pdev->dev, "spi master registration failed: %d\n",
 			ret);
-		goto err_dma_release;
+		goto err_pm_disable;
 	}
 
-	if (!master->cs_gpios) {
+	if (!master->cs_gpiods) {
 		dev_err(&pdev->dev, "no CS gpios available\n");
 		ret = -EINVAL;
-		goto err_dma_release;
-	}
-
-	for (i = 0; i < master->num_chipselect; i++) {
-		if (!gpio_is_valid(master->cs_gpios[i])) {
-			dev_err(&pdev->dev, "%i is not a valid gpio\n",
-				master->cs_gpios[i]);
-			ret = -EINVAL;
-			goto err_dma_release;
-		}
-
-		ret = devm_gpio_request(&pdev->dev, master->cs_gpios[i],
-					DRIVER_NAME);
-		if (ret) {
-			dev_err(&pdev->dev, "can't get CS gpio %i\n",
-				master->cs_gpios[i]);
-			goto err_dma_release;
-		}
+		goto err_pm_disable;
 	}
 
 	dev_info(&pdev->dev, "driver initialized\n");
 
 	return 0;
 
+err_pm_disable:
+	pm_runtime_disable(&pdev->dev);
 err_dma_release:
 	if (spi->dma_tx)
 		dma_release_channel(spi->dma_tx);
 	if (spi->dma_rx)
 		dma_release_channel(spi->dma_rx);
-
-	pm_runtime_disable(&pdev->dev);
 err_clk_disable:
 	clk_disable_unprepare(spi->clk);
 err_master_put:

drivers/spi/spi-tegra114.c

@@ -269,10 +269,10 @@ static unsigned tegra_spi_calculate_curr_xfer_param(
 
 	if ((bits_per_word == 8 || bits_per_word == 16 ||
 	     bits_per_word == 32) && t->len > 3) {
-		tspi->is_packed = 1;
+		tspi->is_packed = true;
 		tspi->words_per_32bit = 32/bits_per_word;
 	} else {
-		tspi->is_packed = 0;
+		tspi->is_packed = false;
 		tspi->words_per_32bit = 1;
 	}
 

drivers/spi/spi-ti-qspi.c

@@ -80,8 +80,6 @@ struct ti_qspi {
 
 #define QSPI_COMPLETION_TIMEOUT		msecs_to_jiffies(2000)
 
-#define QSPI_FCLK			192000000
-
 /* Clock Control */
 #define QSPI_CLK_EN			(1 << 31)
 #define QSPI_CLK_DIV_MAX		0xffff
@@ -316,6 +314,8 @@ static int qspi_read_msg(struct ti_qspi *qspi, struct spi_transfer *t,
 {
 	int wlen;
 	unsigned int cmd;
+	u32 rx;
+	u8 rxlen, rx_wlen;
 	u8 *rxbuf;
 
 	rxbuf = t->rx_buf;
@@ -332,20 +332,67 @@ static int qspi_read_msg(struct ti_qspi *qspi, struct spi_transfer *t,
 		break;
 	}
 	wlen = t->bits_per_word >> 3;	/* in bytes */
+	rx_wlen = wlen;
 
 	while (count) {
 		dev_dbg(qspi->dev, "rx cmd %08x dc %08x\n", cmd, qspi->dc);
 		if (qspi_is_busy(qspi))
 			return -EBUSY;
 
+		switch (wlen) {
+		case 1:
+			/*
+			 * Optimize the 8-bit words transfers, as used by
+			 * the SPI flash devices.
+			 */
+			if (count >= QSPI_WLEN_MAX_BYTES) {
+				rxlen = QSPI_WLEN_MAX_BYTES;
+			} else {
+				rxlen = min(count, 4);
+			}
+			rx_wlen = rxlen << 3;
+			cmd &= ~QSPI_WLEN_MASK;
+			cmd |= QSPI_WLEN(rx_wlen);
+			break;
+		default:
+			rxlen = wlen;
+			break;
+		}
+
 		ti_qspi_write(qspi, cmd, QSPI_SPI_CMD_REG);
 		if (ti_qspi_poll_wc(qspi)) {
 			dev_err(qspi->dev, "read timed out\n");
 			return -ETIMEDOUT;
 		}
+
 		switch (wlen) {
 		case 1:
-			*rxbuf = readb(qspi->base + QSPI_SPI_DATA_REG);
+			/*
+			 * Optimize the 8-bit words transfers, as used by
+			 * the SPI flash devices.
+			 */
+			if (count >= QSPI_WLEN_MAX_BYTES) {
+				u32 *rxp = (u32 *) rxbuf;
+				rx = readl(qspi->base + QSPI_SPI_DATA_REG_3);
+				*rxp++ = be32_to_cpu(rx);
+				rx = readl(qspi->base + QSPI_SPI_DATA_REG_2);
+				*rxp++ = be32_to_cpu(rx);
+				rx = readl(qspi->base + QSPI_SPI_DATA_REG_1);
+				*rxp++ = be32_to_cpu(rx);
+				rx = readl(qspi->base + QSPI_SPI_DATA_REG);
+				*rxp++ = be32_to_cpu(rx);
+			} else {
+				u8 *rxp = rxbuf;
+				rx = readl(qspi->base + QSPI_SPI_DATA_REG);
+				if (rx_wlen >= 8)
+					*rxp++ = rx >> (rx_wlen - 8);
+				if (rx_wlen >= 16)
+					*rxp++ = rx >> (rx_wlen - 16);
+				if (rx_wlen >= 24)
+					*rxp++ = rx >> (rx_wlen - 24);
+				if (rx_wlen >= 32)
+					*rxp++ = rx;
+			}
 			break;
 		case 2:
 			*((u16 *)rxbuf) = readw(qspi->base + QSPI_SPI_DATA_REG);
@@ -354,8 +401,8 @@ static int qspi_read_msg(struct ti_qspi *qspi, struct spi_transfer *t,
 			*((u32 *)rxbuf) = readl(qspi->base + QSPI_SPI_DATA_REG);
 			break;
 		}
-		rxbuf += wlen;
-		count -= wlen;
+		rxbuf += rxlen;
+		count -= rxlen;
 	}
 
 	return 0;
@@ -527,6 +574,35 @@ static void ti_qspi_setup_mmap_read(struct spi_device *spi, u8 opcode,
 		      QSPI_SPI_SETUP_REG(spi->chip_select));
 }
 
+static int ti_qspi_adjust_op_size(struct spi_mem *mem, struct spi_mem_op *op)
+{
+	struct ti_qspi *qspi = spi_controller_get_devdata(mem->spi->master);
+	size_t max_len;
+
+	if (op->data.dir == SPI_MEM_DATA_IN) {
+		if (op->addr.val < qspi->mmap_size) {
+			/* Limit MMIO to the mmaped region */
+			if (op->addr.val + op->data.nbytes > qspi->mmap_size) {
+				max_len = qspi->mmap_size - op->addr.val;
+				op->data.nbytes = min((size_t) op->data.nbytes,
+						      max_len);
+			}
+		} else {
+			/*
+			 * Use fallback mode (SW generated transfers) above the
+			 * mmaped region.
+			 * Adjust size to comply with the QSPI max frame length.
+			 */
+			max_len = QSPI_FRAME;
+			max_len -= 1 + op->addr.nbytes + op->dummy.nbytes;
+			op->data.nbytes = min((size_t) op->data.nbytes,
+					      max_len);
+		}
+	}
+
+	return 0;
+}
+
 static int ti_qspi_exec_mem_op(struct spi_mem *mem,
 			       const struct spi_mem_op *op)
 {
@@ -577,6 +653,7 @@ static int ti_qspi_exec_mem_op(struct spi_mem *mem,
 
 static const struct spi_controller_mem_ops ti_qspi_mem_ops = {
 	.exec_op = ti_qspi_exec_mem_op,
+	.adjust_op_size = ti_qspi_adjust_op_size,
 };
 
 static int ti_qspi_start_transfer_one(struct spi_master *master,

drivers/spi/spi-topcliff-pch.c

@@ -863,7 +863,7 @@ static void pch_spi_request_dma(struct pch_spi_data *data, int bpw)
 	/* Set Tx DMA */
 	param = &dma->param_tx;
 	param->dma_dev = &dma_dev->dev;
-	param->chan_id = data->ch * 2; /* Tx = 0, 2 */;
+	param->chan_id = data->ch * 2; /* Tx = 0, 2 */
 	param->tx_reg = data->io_base_addr + PCH_SPDWR;
 	param->width = width;
 	chan = dma_request_channel(mask, pch_spi_filter, param);
@@ -878,7 +878,7 @@ static void pch_spi_request_dma(struct pch_spi_data *data, int bpw)
 	/* Set Rx DMA */
 	param = &dma->param_rx;
 	param->dma_dev = &dma_dev->dev;
-	param->chan_id = data->ch * 2 + 1; /* Rx = Tx + 1 */;
+	param->chan_id = data->ch * 2 + 1; /* Rx = Tx + 1 */
 	param->rx_reg = data->io_base_addr + PCH_SPDRR;
 	param->width = width;
 	chan = dma_request_channel(mask, pch_spi_filter, param);

drivers/spi/spi.c

@@ -1674,6 +1674,13 @@ void spi_finalize_current_message(struct spi_controller *ctlr)
 		}
 	}
 
+	if (unlikely(ctlr->ptp_sts_supported)) {
+		list_for_each_entry(xfer, &mesg->transfers, transfer_list) {
+			WARN_ON_ONCE(xfer->ptp_sts && !xfer->timestamped_pre);
+			WARN_ON_ONCE(xfer->ptp_sts && !xfer->timestamped_post);
+		}
+	}
+
 	spi_unmap_msg(ctlr, mesg);
 
 	if (ctlr->cur_msg_prepared && ctlr->unprepare_message) {
@@ -2451,6 +2458,8 @@ static int spi_get_gpio_descs(struct spi_controller *ctlr)
 	int nb, i;
 	struct gpio_desc **cs;
 	struct device *dev = &ctlr->dev;
+	unsigned long native_cs_mask = 0;
+	unsigned int num_cs_gpios = 0;
 
 	nb = gpiod_count(dev, "cs");
 	ctlr->num_chipselect = max_t(int, nb, ctlr->num_chipselect);
@@ -2492,7 +2501,22 @@ static int spi_get_gpio_descs(struct spi_controller *ctlr)
 			if (!gpioname)
 				return -ENOMEM;
 			gpiod_set_consumer_name(cs[i], gpioname);
+			num_cs_gpios++;
+			continue;
 		}
+
+		if (ctlr->max_native_cs && i >= ctlr->max_native_cs) {
+			dev_err(dev, "Invalid native chip select %d\n", i);
+			return -EINVAL;
+		}
+		native_cs_mask |= BIT(i);
+	}
+
+	ctlr->unused_native_cs = ffz(native_cs_mask);
+	if (num_cs_gpios && ctlr->max_native_cs &&
+	    ctlr->unused_native_cs >= ctlr->max_native_cs) {
+		dev_err(dev, "No unused native chip select available\n");
+		return -EINVAL;
 	}
 
 	return 0;

include/linux/spi/spi.h

@@ -423,6 +423,12 @@ static inline void spi_unregister_driver(struct spi_driver *sdrv)
  *	GPIO descriptors rather than using global GPIO numbers grabbed by the
  *	driver. This will fill in @cs_gpiods and @cs_gpios should not be used,
  *	and SPI devices will have the cs_gpiod assigned rather than cs_gpio.
+ * @unused_native_cs: When cs_gpiods is used, spi_register_controller() will
+ *	fill in this field with the first unused native CS, to be used by SPI
+ *	controller drivers that need to drive a native CS when using GPIO CS.
+ * @max_native_cs: When cs_gpiods is used, and this field is filled in,
+ *	spi_register_controller() will validate all native CS (including the
+ *	unused native CS) against this value.
  * @statistics: statistics for the spi_controller
  * @dma_tx: DMA transmit channel
  * @dma_rx: DMA receive channel
@@ -624,6 +630,8 @@ struct spi_controller {
 	int			*cs_gpios;
 	struct gpio_desc	**cs_gpiods;
 	bool			use_gpio_descriptors;
+	u8			unused_native_cs;
+	u8			max_native_cs;
 
 	/* statistics */
 	struct spi_statistics	statistics;

include/linux/spi/spi_oc_tiny.h

@@ -6,16 +6,12 @@
  * struct tiny_spi_platform_data - platform data of the OpenCores tiny SPI
  * @freq:	input clock freq to the core.
  * @baudwidth:	baud rate divider width of the core.
- * @gpio_cs_count:	number of gpio pins used for chipselect.
- * @gpio_cs:	array of gpio pins used for chipselect.
  *
  * freq and baudwidth are used only if the divider is programmable.
  */
 struct tiny_spi_platform_data {
 	unsigned int freq;
 	unsigned int baudwidth;
-	unsigned int gpio_cs_count;
-	int *gpio_cs;
 };
 
 #endif /* _LINUX_SPI_SPI_OC_TINY_H */