Commit 1ec6360d authored by Walter Heymans's avatar Walter Heymans Committed by Jakub Kicinski

Documentation: nfp: update documentation

The NFP documentation is updated to include information about Corigine,
and the new NFP3800 chips. The 'Acquiring Firmware' section is updated
with new information about where to find firmware.

Two new sections are added to expand the coverage of the documentation.
The new sections include:
- Devlink Info
- Configure Device
Signed-off-by: default avatarWalter Heymans <walter.heymans@corigine.com>
Reviewed-by: default avatarNiklas Söderlund <niklas.soderlund@corigine.com>
Reviewed-by: default avatarLouis Peens <louis.peens@corigine.com>
Signed-off-by: default avatarSimon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20221115090834.738645-1-simon.horman@corigine.comSigned-off-by: default avatarJakub Kicinski <kuba@kernel.org>
parent 0f54d36e
.. SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
.. include:: <isonum.txt>
=============================================
Netronome Flow Processor (NFP) Kernel Drivers
=============================================
===========================================
Network Flow Processor (NFP) Kernel Drivers
===========================================
Copyright (c) 2019, Netronome Systems, Inc.
:Copyright: |copy| 2019, Netronome Systems, Inc.
:Copyright: |copy| 2022, Corigine, Inc.
Contents
========
- `Overview`_
- `Acquiring Firmware`_
- `Devlink Info`_
- `Configure Device`_
- `Statistics`_
Overview
========
This driver supports Netronome's line of Flow Processor devices,
including the NFP4000, NFP5000, and NFP6000 models, which are also
incorporated in the company's family of Agilio SmartNICs. The SR-IOV
physical and virtual functions for these devices are supported by
the driver.
This driver supports Netronome and Corigine's line of Network Flow Processor
devices, including the NFP3800, NFP4000, NFP5000, and NFP6000 models, which
are also incorporated in the companies' family of Agilio SmartNICs. The SR-IOV
physical and virtual functions for these devices are supported by the driver.
Acquiring Firmware
==================
The NFP4000 and NFP6000 devices require application specific firmware
The NFP3800, NFP4000 and NFP6000 devices require application specific firmware
to function. Application firmware can be located either on the host file system
or in the device flash (if supported by management firmware).
......@@ -35,6 +39,9 @@ load firmware from the host file system.
Firmware for basic NIC operation is available in the upstream
`linux-firmware.git` repository.
A more comprehensive list of firmware can be downloaded from the
`Corigine Support site <https://www.corigine.com/DPUDownload.html>`_.
Firmware in NVRAM
-----------------
......@@ -89,9 +96,9 @@ Selecting firmware per device
-----------------------------
Most commonly all cards on the system use the same type of firmware.
If you want to load specific firmware image for a specific card, you
can use either the PCI bus address or serial number. Driver will print
which files it's looking for when it recognizes a NFP device::
If you want to load a specific firmware image for a specific card, you
can use either the PCI bus address or serial number. The driver will
print which files it's looking for when it recognizes a NFP device::
nfp: Looking for firmware file in order of priority:
nfp: netronome/serial-00-12-34-aa-bb-cc-10-ff.nffw: not found
......@@ -106,6 +113,15 @@ Note that `serial-*` and `pci-*` files are **not** automatically included
in initramfs, you will have to refer to documentation of appropriate tools
to find out how to include them.
Running firmware version
------------------------
The version of the loaded firmware for a particular <netdev> interface,
(e.g. enp4s0), or an interface's port <netdev port> (e.g. enp4s0np0) can
be displayed with the ethtool command::
$ ethtool -i <netdev>
Firmware loading policy
-----------------------
......@@ -132,6 +148,115 @@ abi_drv_load_ifc
Defines a list of PF devices allowed to load FW on the device.
This variable is not currently user configurable.
Devlink Info
============
The devlink info command displays the running and stored firmware versions
on the device, serial number and board information.
Devlink info command example (replace PCI address)::
$ devlink dev info pci/0000:03:00.0
pci/0000:03:00.0:
driver nfp
serial_number CSAAMDA2001-1003000111
versions:
fixed:
board.id AMDA2001-1003
board.rev 01
board.manufacture CSA
board.model mozart
running:
fw.mgmt 22.10.0-rc3
fw.cpld 0x1000003
fw.app nic-22.09.0
chip.init AMDA-2001-1003 1003000111
stored:
fw.bundle_id bspbundle_1003000111
fw.mgmt 22.10.0-rc3
fw.cpld 0x0
chip.init AMDA-2001-1003 1003000111
Configure Device
================
This section explains how to use Agilio SmartNICs running basic NIC firmware.
Configure interface link-speed
------------------------------
The following steps explains how to change between 10G mode and 25G mode on
Agilio CX 2x25GbE cards. The changing of port speed must be done in order,
port 0 (p0) must be set to 10G before port 1 (p1) may be set to 10G.
Down the respective interface(s)::
$ ip link set dev <netdev port 0> down
$ ip link set dev <netdev port 1> down
Set interface link-speed to 10G::
$ ethtool -s <netdev port 0> speed 10000
$ ethtool -s <netdev port 1> speed 10000
Set interface link-speed to 25G::
$ ethtool -s <netdev port 0> speed 25000
$ ethtool -s <netdev port 1> speed 25000
Reload driver for changes to take effect::
$ rmmod nfp; modprobe nfp
Configure interface Maximum Transmission Unit (MTU)
---------------------------------------------------
The MTU of interfaces can temporarily be set using the iproute2, ip link or
ifconfig tools. Note that this change will not persist. Setting this via
Network Manager, or another appropriate OS configuration tool, is
recommended as changes to the MTU using Network Manager can be made to
persist.
Set interface MTU to 9000 bytes::
$ ip link set dev <netdev port> mtu 9000
It is the responsibility of the user or the orchestration layer to set
appropriate MTU values when handling jumbo frames or utilizing tunnels. For
example, if packets sent from a VM are to be encapsulated on the card and
egress a physical port, then the MTU of the VF should be set to lower than
that of the physical port to account for the extra bytes added by the
additional header. If a setup is expected to see fallback traffic between
the SmartNIC and the kernel then the user should also ensure that the PF MTU
is appropriately set to avoid unexpected drops on this path.
Configure Forward Error Correction (FEC) modes
----------------------------------------------
Agilio SmartNICs support FEC mode configuration, e.g. Auto, Firecode Base-R,
ReedSolomon and Off modes. Each physical port's FEC mode can be set
independently using ethtool. The supported FEC modes for an interface can
be viewed using::
$ ethtool <netdev>
The currently configured FEC mode can be viewed using::
$ ethtool --show-fec <netdev>
To force the FEC mode for a particular port, auto-negotiation must be disabled
(see the `Auto-negotiation`_ section). An example of how to set the FEC mode
to Reed-Solomon is::
$ ethtool --set-fec <netdev> encoding rs
Auto-negotiation
----------------
To change auto-negotiation settings, the link must first be put down. After the
link is down, auto-negotiation can be enabled or disabled using::
ethtool -s <netdev> autoneg <on|off>
Statistics
==========
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment