Merge tag 'imx-dt-4.10' of...

Merge tag 'imx-dt-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt

i.MX device tree updates for 4.10:
 - New boards support: i.MX6SX UDOO Neo, Boundary Devices Nitrogen6_SOM2,
   Engicam i.CoreM6, Grinn i.MX6UL liteSOM/liteBoard, Toradex Colibri
   iMX6 module, i.MX6ULL and EVK board.
 - Remove skeleton.dtsi inclusion from all i.MX SoC dts files, as it's
   been deprecated, since commit 9c0da3cc ("ARM: dts: explicitly
   mark skeleton.dtsi as deprecated").
 - Misc device addition and enabling: OCOTP for Vybrid, MMDC for i.MX6QP,
   TMU for LS1021A, FEC for imx6qdl-icore, DMA for Vybrid DSPI.
 - A few cleanups: use hyphens for node names, fix white spaces, move
   imx-weim parameters into SoC dtsi, replace gpio-key,wakeup with
   wakeup-source, remove pwm-leds from imx6q-apalis-ixora, remove I2C3
   from vf610-zii-dev-rev-b.
 - Other small random changes: calibrate USB PHY for b650v3 board,
   update TX D_CAL for USBPHY, use enable-gpios for backlight on
   imx6qdl-apalis, etc.

* tag 'imx-dt-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (38 commits)
  ARM: dts: imx6ull: add imx6ull support
  ARM: dts: imx6q: replace gpio-key,wakeup with wakeup-source for Utilite Pro
  ARM: dts: vfxxx: Enable DMA for DSPI2 and DSPI3
  ARM: dts: imx: Remove skeleton.dtsi
  ARM: dts: imx6q-utilite-pro: i2c1 is muxed
  ARM: dts: add new compatible string for i.MX6QP mmdc
  ARM: dts: imx6sx-udoo: Add board specific compatible strings
  ARM: dts: mx5: Add new M53EVK manufacturer compat
  ARM: dts: mxs: Add new M28EVK manufacturer compat
  ARM: dts: imx6ul-14x14-evk: update TX D_CAL for USBPHY
  ARM: dts: imx6sx-sdb: update TX D_CAL for USBPHY
  ARM: dts: imx6: Add imx-weim parameters to dtsi's
  ARM: dts: imx: Fix "ERROR: code indent should use tabs where possible"
  ARM: dts: imx6qdl-nitrogen6_max: use hyphens for nodes name
  ARM: dts: imx6qdl-nit6xlite: use hyphens for nodes name
  ARM: dts: imx6qdl-nitrogen6x: use hyphens for nodes name
  ARM: dts: imx6qdl-sabrelite: use hyphens for nodes name
  ARM: dts: imx: add Boundary Devices Nitrogen6_SOM2 support
  ARM: dts: imx6qdl-icore: Add FEC support
  ARM: dts: imx6q: Add Engicam i.CoreM6 DualLite/Solo initial support
  ...
Signed-off-by: Olof Johansson <olof@lixom.net>

arch/arm/boot/dts/Makefile

@@ -331,6 +331,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
 	imx6dl-aristainetos_7.dtb \
 	imx6dl-aristainetos2_4.dtb \
 	imx6dl-aristainetos2_7.dtb \
+	imx6dl-colibri-eval-v3.dtb \
 	imx6dl-cubox-i.dtb \
 	imx6dl-dfi-fs700-m60.dtb \
 	imx6dl-gw51xx.dtb \
@@ -341,6 +342,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
 	imx6dl-gw552x.dtb \
 	imx6dl-gw553x.dtb \
 	imx6dl-hummingboard.dtb \
+	imx6dl-icore.dtb \
 	imx6dl-nit6xlite.dtb \
 	imx6dl-nitrogen6x.dtb \
 	imx6dl-phytec-pbab01.dtb \
@@ -382,10 +384,12 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
 	imx6q-gw553x.dtb \
 	imx6q-h100.dtb \
 	imx6q-hummingboard.dtb \
+	imx6q-icore.dtb \
 	imx6q-icore-rqs.dtb \
 	imx6q-marsboard.dtb \
 	imx6q-nitrogen6x.dtb \
 	imx6q-nitrogen6_max.dtb \
+	imx6q-nitrogen6_som2.dtb \
 	imx6q-novena.dtb \
 	imx6q-phytec-pbab01.dtb \
 	imx6q-rex-pro.dtb \
@@ -417,14 +421,19 @@ dtb-$(CONFIG_SOC_IMX6SX) += \
 	imx6sx-sabreauto.dtb \
 	imx6sx-sdb-reva.dtb \
 	imx6sx-sdb-sai.dtb \
-	imx6sx-sdb.dtb
+	imx6sx-sdb.dtb \
+	imx6sx-udoo-neo-basic.dtb \
+	imx6sx-udoo-neo-extended.dtb \
+	imx6sx-udoo-neo-full.dtb
 dtb-$(CONFIG_SOC_IMX6UL) += \
 	imx6ul-14x14-evk.dtb \
 	imx6ul-geam-kit.dtb \
+	imx6ul-liteboard.dtb \
 	imx6ul-pico-hobbit.dtb \
 	imx6ul-tx6ul-0010.dtb \
 	imx6ul-tx6ul-0011.dtb \
-	imx6ul-tx6ul-mainboard.dtb
+	imx6ul-tx6ul-mainboard.dtb \
+	imx6ull-14x14-evk.dtb
 dtb-$(CONFIG_SOC_IMX7D) += \
 	imx7d-cl-som-imx7.dtb \
 	imx7d-colibri-eval-v3.dtb \

arch/arm/boot/dts/imx1.dtsi

@@ -9,7 +9,6 @@
  * http://www.gnu.org/copyleft/gpl.html
  */
 
-#include "skeleton.dtsi"
 #include "imx1-pinfunc.h"
 
 #include <dt-bindings/clock/imx1-clock.h>
@@ -17,6 +16,9 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 
 / {
+	#address-cells = <1>;
+	#size-cells = <1>;
+
 	aliases {
 		gpio0 = &gpio1;
 		gpio1 = &gpio2;

arch/arm/boot/dts/imx23.dtsi

@@ -9,10 +9,12 @@
  * http://www.gnu.org/copyleft/gpl.html
  */
 
-#include "skeleton.dtsi"
 #include "imx23-pinfunc.h"
 
 / {
+	#address-cells = <1>;
+	#size-cells = <1>;
+
 	interrupt-parent = <&icoll>;
 
 	aliases {

arch/arm/boot/dts/imx25.dtsi

@@ -9,10 +9,12 @@
  * http://www.gnu.org/copyleft/gpl.html
  */
 
-#include "skeleton.dtsi"
 #include "imx25-pinfunc.h"
 
 / {
+	#address-cells = <1>;
+	#size-cells = <1>;
+
 	aliases {
 		ethernet0 = &fec;
 		gpio0 = &gpio1;

arch/arm/boot/dts/imx27.dtsi

@@ -9,7 +9,6 @@
  * http://www.gnu.org/copyleft/gpl.html
  */
 
-#include "skeleton.dtsi"
 #include "imx27-pinfunc.h"
 
 #include <dt-bindings/clock/imx27-clock.h>
@@ -18,6 +17,9 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 
 / {
+	#address-cells = <1>;
+	#size-cells = <1>;
+
 	aliases {
 		ethernet0 = &fec;
 		gpio0 = &gpio1;

arch/arm/boot/dts/imx28-m28.dtsi

@@ -12,8 +12,8 @@
 #include "imx28.dtsi"
 
 / {
-	model = "DENX M28";
-	compatible = "denx,m28", "fsl,imx28";
+	model = "Aries/DENX M28";
+	compatible = "aries,m28", "denx,m28", "fsl,imx28";
 
 	memory {
 		reg = <0x40000000 0x08000000>;

arch/arm/boot/dts/imx28-m28evk.dts

@@ -13,8 +13,8 @@
 #include "imx28-m28.dtsi"
 
 / {
-	model = "DENX M28EVK";
-	compatible = "denx,m28evk", "fsl,imx28";
+	model = "Aries/DENX M28EVK";
+	compatible = "aries,m28evk", "denx,m28evk", "fsl,imx28";
 
 	apb@80000000 {
 		apbh@80000000 {

arch/arm/boot/dts/imx28.dtsi

@@ -10,10 +10,12 @@
  */
 
 #include <dt-bindings/gpio/gpio.h>
-#include "skeleton.dtsi"
 #include "imx28-pinfunc.h"
 
 / {
+	#address-cells = <1>;
+	#size-cells = <1>;
+
 	interrupt-parent = <&icoll>;
 
 	aliases {

arch/arm/boot/dts/imx31.dtsi

@@ -9,9 +9,10 @@
  * http://www.gnu.org/copyleft/gpl.html
  */
 
-#include "skeleton.dtsi"
-
 / {
+	#address-cells = <1>;
+	#size-cells = <1>;
+
 	aliases {
 		serial0 = &uart1;
 		serial1 = &uart2;

arch/arm/boot/dts/imx35.dtsi

@@ -8,10 +8,12 @@
  * Free Software Foundation.
  */
 
-#include "skeleton.dtsi"
 #include "imx35-pinfunc.h"
 
 / {
+	#address-cells = <1>;
+	#size-cells = <1>;
+
 	aliases {
 		ethernet0 = &fec;
 		gpio0 = &gpio1;

arch/arm/boot/dts/imx50.dtsi

@@ -11,11 +11,13 @@
  * http://www.gnu.org/copyleft/gpl.html
  */
 
-#include "skeleton.dtsi"
 #include "imx50-pinfunc.h"
 #include <dt-bindings/clock/imx5-clock.h>
 
 / {
+	#address-cells = <1>;
+	#size-cells = <1>;
+
 	aliases {
 		ethernet0 = &fec;
 		gpio0 = &gpio1;

arch/arm/boot/dts/imx51.dtsi

@@ -10,7 +10,6 @@
  * http://www.gnu.org/copyleft/gpl.html
  */
 
-#include "skeleton.dtsi"
 #include "imx51-pinfunc.h"
 #include <dt-bindings/clock/imx5-clock.h>
 #include <dt-bindings/gpio/gpio.h>
@@ -18,6 +17,9 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 
 / {
+	#address-cells = <1>;
+	#size-cells = <1>;
+
 	aliases {
 		ethernet0 = &fec;
 		gpio0 = &gpio1;

arch/arm/boot/dts/imx53-m53.dtsi

@@ -12,8 +12,8 @@
 #include "imx53.dtsi"
 
 / {
-	model = "DENX M53";
-	compatible = "denx,imx53-m53", "fsl,imx53";
+	model = "Aries/DENX M53";
+	compatible = "aries,imx53-m53", "denx,imx53-m53", "fsl,imx53";
 
 	memory {
 		reg = <0x70000000 0x20000000>,

arch/arm/boot/dts/imx53-m53evk.dts

@@ -13,8 +13,8 @@
 #include "imx53-m53.dtsi"
 
 / {
-	model = "DENX M53EVK";
-	compatible = "denx,imx53-m53evk", "fsl,imx53";
+	model = "Aries/DENX M53EVK";
+	compatible = "aries,imx53-m53evk", "denx,imx53-m53evk", "fsl,imx53";
 
 	display1: display@di1 {
 		compatible = "fsl,imx-parallel-display";

arch/arm/boot/dts/imx53.dtsi

@@ -10,7 +10,6 @@
  * http://www.gnu.org/copyleft/gpl.html
  */
 
-#include "skeleton.dtsi"
 #include "imx53-pinfunc.h"
 #include <dt-bindings/clock/imx5-clock.h>
 #include <dt-bindings/gpio/gpio.h>
@@ -18,6 +17,9 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 
 / {
+	#address-cells = <1>;
+	#size-cells = <1>;
+
 	aliases {
 		ethernet0 = &fec;
 		gpio0 = &gpio1;

arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts

+/*
+ * Copyright 2014-2016 Toradex AG
+ * Copyright 2012 Freescale Semiconductor, Inc.
+ * Copyright 2011 Linaro Ltd.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License
+ *     version 2 as published by the Free Software Foundation.
+ *
+ *     This file is distributed in the hope that it will be useful
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include "imx6dl.dtsi"
+#include "imx6qdl-colibri.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX6DL/S on Colibri Evaluation Board V3";
+	compatible = "toradex,colibri_imx6dl-eval-v3", "toradex,colibri_imx6dl",
+		     "fsl,imx6dl";
+
+	aliases {
+		i2c0 = &i2c2;
+		i2c1 = &i2c3;
+	};
+
+	aliases {
+		rtc0 = &rtc_i2c;
+		rtc1 = &snvs_rtc;
+	};
+
+	clocks {
+		/* Fixed crystal dedicated to mcp251x */
+		clk16m: clk@1 {
+			compatible = "fixed-clock";
+			reg = <1>;
+			#clock-cells = <0>;
+			clock-frequency = <16000000>;
+			clock-output-names = "clk16m";
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_keys>;
+
+		wakeup {
+			label = "Wake-Up";
+			gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>; /* SODIMM 45 */
+			linux,code = <KEY_WAKEUP>;
+			debounce-interval = <10>;
+			wakeup-source;
+		};
+	};
+
+	lcd_display: display@di0 {
+		compatible = "fsl,imx-parallel-display";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		interface-pix-fmt = "bgr666";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ipu1_lcdif>;
+		status = "okay";
+
+		port@0 {
+			reg = <0>;
+
+			lcd_display_in: endpoint {
+				remote-endpoint = <&ipu1_di0_disp0>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			lcd_display_out: endpoint {
+				remote-endpoint = <&lcd_panel_in>;
+			};
+		};
+	};
+
+	panel: panel {
+		/*
+		 * edt,et057090dhu: EDT 5.7" LCD TFT
+		 * edt,et070080dh6: EDT 7.0" LCD TFT
+		 */
+		compatible = "edt,et057090dhu";
+		backlight = <&backlight>;
+
+		port {
+			lcd_panel_in: endpoint {
+				remote-endpoint = <&lcd_display_out>;
+			};
+		};
+	};
+};
+
+&backlight {
+	brightness-levels = <0 127 191 223 239 247 251 255>;
+	default-brightness-level = <1>;
+	status = "okay";
+};
+
+/* Colibri SSP */
+&ecspi4 {
+	status = "okay";
+
+	mcp251x0: mcp251x@1 {
+		compatible = "microchip,mcp2515";
+		reg = <0>;
+		clocks = <&clk16m>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <27 0x2>;
+		spi-max-frequency = <10000000>;
+		status = "okay";
+	};
+};
+
+&hdmi {
+	status = "okay";
+};
+
+/*
+ * Colibri I2C: I2C3_SDA/SCL on SODIMM 194/196 (e.g. RTC on carrier board)
+ */
+&i2c3 {
+	status = "okay";
+
+	/* M41T0M6 real time clock on carrier board */
+	rtc_i2c: rtc@68 {
+		compatible = "st,m41t00";
+		reg = <0x68>;
+	};
+};
+
+&ipu1_di0_disp0 {
+	remote-endpoint = <&lcd_display_in>;
+};
+
+&pwm1 {
+	status = "okay";
+};
+
+&pwm2 {
+	status = "okay";
+};
+
+&pwm3 {
+	status = "okay";
+};
+
+&pwm4 {
+	status = "okay";
+};
+
+&reg_usb_host_vbus {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&usbh1 {
+	vbus-supply = <&reg_usb_host_vbus>;
+	status = "okay";
+};
+
+&usbotg {
+	status = "okay";
+};
+
+/* Colibri MMC */
+&usdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_mmc_cd>;
+	cd-gpios = <&gpio2 5 GPIO_ACTIVE_LOW>; /* MMCD */
+	status = "okay";
+};
+
+&weim {
+	status = "okay";
+
+	/* weim memory map: 32MB on CS0, 32MB on CS1, 32MB on CS2 */
+	ranges = <0 0 0x08000000 0x02000000
+		  1 0 0x0a000000 0x02000000
+		  2 0 0x0c000000 0x02000000>;
+
+	/* SRAM on Colibri nEXT_CS0 */
+	sram@0,0 {
+		compatible = "cypress,cy7c1019dv33-10zsxi, mtd-ram";
+		reg = <0 0 0x00010000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		bank-width = <2>;
+		fsl,weim-cs-timing = <0x00010081 0x00000000 0x04000000
+				      0x00000000 0x04000040 0x00000000>;
+	};
+
+	/* SRAM on Colibri nEXT_CS1 */
+	sram@1,0 {
+		compatible = "cypress,cy7c1019dv33-10zsxi, mtd-ram";
+		reg = <1 0 0x00010000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		bank-width = <2>;
+		fsl,weim-cs-timing = <0x00010081 0x00000000 0x04000000
+				      0x00000000 0x04000040 0x00000000>;
+	};
+};

arch/arm/boot/dts/imx6dl-icore.dts

+/*
+ * Copyright (C) 2016 Amarula Solutions B.V.
+ * Copyright (C) 2016 Engicam S.r.l.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License
+ *     version 2 as published by the Free Software Foundation.
+ *
+ *     This file is distributed in the hope that it will be useful
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "imx6dl.dtsi"
+#include "imx6qdl-icore.dtsi"
+
+/ {
+	model = "Engicam i.CoreM6 DualLite/Solo Starter Kit";
+	compatible = "engicam,imx6-icore", "fsl,imx6dl";
+};
+
+&can1 {
+	status = "okay";
+};
+
+&can2 {
+	status = "okay";
+};

arch/arm/boot/dts/imx6q-apalis-ixora.dts

@@ -147,28 +147,6 @@ led5-red {
 			gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>;
 		};
 	};
-
-	pwmleds {
-		compatible = "pwm-leds";
-
-		ledpwm1 {
-			label = "PWM1";
-			pwms = <&pwm1 0 50000>;
-			max-brightness = <255>;
-		};
-
-		ledpwm2 {
-			label = "PWM2";
-			pwms = <&pwm2 0 50000>;
-			max-brightness = <255>;
-		};
-
-		ledpwm3 {
-			label = "PWM3";
-			pwms = <&pwm3 0 50000>;
-			max-brightness = <255>;
-		};
-	};
 };
 
 &backlight {

arch/arm/boot/dts/imx6q-b650v3.dts

@@ -98,3 +98,9 @@ P05 {
 		line-name = "PCA9539-P05";
 	};
 };
+
+&usbphy1 {
+	fsl,tx-cal-45-dn-ohms = <55>;
+	fsl,tx-cal-45-dp-ohms = <55>;
+	fsl,tx-d-cal = <100>;
+};

arch/arm/boot/dts/imx6q-evi.dts

@@ -232,10 +232,7 @@ &usdhc1 {
 };
 
 &weim {
-	#address-cells = <2>;
-	#size-cells = <1>;
 	ranges = <0 0 0x08000000 0x08000000>;
-	fsl,weim-cs-gpr = <&gpr>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_weimfpga &pinctrl_weimcs>;
 	status = "okay";

arch/arm/boot/dts/imx6q-icore.dts

+/*
+ * Copyright (C) 2016 Amarula Solutions B.V.
+ * Copyright (C) 2016 Engicam S.r.l.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License
+ *     version 2 as published by the Free Software Foundation.
+ *
+ *     This file is distributed in the hope that it will be useful
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "imx6q.dtsi"
+#include "imx6qdl-icore.dtsi"
+
+/ {
+	model = "Engicam i.CoreM6 Quad/Dual Starter Kit";
+	compatible = "engicam,imx6-icore", "fsl,imx6q";
+};
+
+&can1 {
+	status = "okay";
+};
+
+&can2 {
+	status = "okay";
+};

arch/arm/boot/dts/imx6q-nitrogen6_som2.dts

+/*
+ * Copyright 2016 Boundary Devices, Inc.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License
+ *     version 2 as published by the Free Software Foundation.
+ *
+ *     This file is distributed in the hope that it will be useful
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+/dts-v1/;
+
+#include "imx6q.dtsi"
+#include "imx6qdl-nitrogen6_som2.dtsi"
+
+/ {
+	model = "Boundary Devices i.MX6 Quad Nitrogen6_SOM2 Board";
+	compatible = "boundary,imx6q-nitrogen6_som2", "fsl,imx6q";
+};
+
+&sata {
+	status = "okay";
+};

arch/arm/boot/dts/imx6q-novena.dts

@@ -451,6 +451,10 @@ &pcie {
 	status = "okay";
 };
 
+&pwm1 {
+	status = "okay";
+};
+
 &sata {
 	target-supply = <&reg_sata>;
 	fsl,transmit-level-mV = <1025>;

arch/arm/boot/dts/imx6q-utilite-pro.dts

@@ -68,20 +68,24 @@ power {
 			label = "Power Button";
 			gpios = <&gpio1 29 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 	};
-};
-
-&hdmi {
-	ddc-i2c-bus = <&i2c2>;
-	status = "okay";
-};
 
-&i2c1 {
+	i2cmux {
+		compatible = "i2c-mux-gpio";
 		pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c1>;
-	status = "okay";
+		pinctrl-0 = <&pinctrl_i2c1mux>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		mux-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+		i2c-parent = <&i2c1>;
+
+		i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
 
 			eeprom@50 {
 				compatible = "at24,24c02";
@@ -93,6 +97,25 @@ em3027: rtc@56 {
 				compatible = "emmicro,em3027";
 				reg = <0x56>;
 			};
+		};
+
+		i2c_dvi_ddc: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+};
+
+&hdmi {
+	ddc-i2c-bus = <&i2c2>;
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
 };
 
 &i2c2 {
@@ -115,6 +138,12 @@ MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1
 		>;
 	};
 
+	pinctrl_i2c1mux: i2c1muxgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0
+		>;
+	};
+
 	pinctrl_i2c2: i2c2grp {
 		fsl,pins = <
 			MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1

arch/arm/boot/dts/imx6qdl-apalis.dtsi

@@ -49,7 +49,10 @@ / {
 
 	backlight: backlight {
 		compatible = "pwm-backlight";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_bl_on>;
 		pwms = <&pwm4 0 5000000>;
+		enable-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
 		status = "disabled";
 	};
 
@@ -620,6 +623,12 @@ MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0x1b0b0
 		>;
 	};
 
+	pinctrl_gpio_bl_on: gpioblon {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_DA13__GPIO3_IO13 0x1b0b0
+		>;
+	};
+
 	pinctrl_gpio_keys: gpio1io04grp {
 		fsl,pins = <
 			/* Power button */

arch/arm/boot/dts/imx6qdl-icore.dtsi

+/*
+ * Copyright (C) 2016 Amarula Solutions B.V.
+ * Copyright (C) 2016 Engicam S.r.l.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License
+ *     version 2 as published by the Free Software Foundation.
+ *
+ *     This file is distributed in the hope that it will be useful
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	memory {
+		reg = <0x10000000 0x80000000>;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	reg_usb_h1_vbus: regulator-usb-h1-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_h1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	reg_usb_otg_vbus: regulator-usb-otg-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	rmii_clk: clock-rmii-clk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <25000000>;  /* 25MHz for example */
+	};
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan1>;
+	xceiver-supply = <&reg_3p3v>;
+};
+
+&can2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan2>;
+	xceiver-supply = <&reg_3p3v>;
+};
+
+&clks {
+	assigned-clocks = <&clks IMX6QDL_CLK_LVDS2_SEL>;
+	assigned-clock-parents = <&clks IMX6QDL_CLK_OSC>;
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-reset-gpios = <&gpio7 12 GPIO_ACTIVE_LOW>;
+	clocks = <&clks IMX6QDL_CLK_ENET>, <&clks IMX6QDL_CLK_ENET>, <&rmii_clk>;
+	phy-mode = "rmii";
+	status = "okay";
+};
+
+&gpmi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpmi_nand>;
+	nand-on-flash-bbt;
+	status = "okay";
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	status = "okay";
+};
+
+&usbh1 {
+	vbus-supply = <&reg_usb_h1_vbus>;
+	disable-over-current;
+	status = "okay";
+};
+
+&usbotg {
+	vbus-supply = <&reg_usb_otg_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	disable-over-current;
+	status = "okay";
+};
+
+&usdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+	no-1-8-v;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN	0x1b0b0
+			MX6QDL_PAD_GPIO_16__ENET_REF_CLK	0x1b0b1
+			MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN	0x1b0b0
+			MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1	0x1b0b0
+			MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0	0x1b0b0
+			MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1	0x1b0b0
+			MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0	0x1b0b0
+			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
+			MX6QDL_PAD_ENET_REF_CLK__GPIO1_IO23	0x1b0b0
+			MX6QDL_PAD_GPIO_17__GPIO7_IO12		0x1b0b0
+		>;
+	};
+
+	pinctrl_flexcan1: flexcan1grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x1b020
+			MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x1b020
+		>;
+	};
+
+	pinctrl_flexcan2: flexcan2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0x1b020
+			MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0x1b020
+		>;
+	};
+
+	pinctrl_gpmi_nand: gpmi-nand {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_CLE__NAND_CLE     0xb0b1
+			MX6QDL_PAD_NANDF_ALE__NAND_ALE     0xb0b1
+			MX6QDL_PAD_NANDF_WP_B__NAND_WP_B   0xb0b1
+			MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000
+			MX6QDL_PAD_NANDF_CS0__NAND_CE0_B   0xb0b1
+			MX6QDL_PAD_NANDF_CS1__NAND_CE1_B   0xb0b1
+			MX6QDL_PAD_SD4_CMD__NAND_RE_B      0xb0b1
+			MX6QDL_PAD_SD4_CLK__NAND_WE_B      0xb0b1
+			MX6QDL_PAD_NANDF_D0__NAND_DATA00   0xb0b1
+			MX6QDL_PAD_NANDF_D1__NAND_DATA01   0xb0b1
+			MX6QDL_PAD_NANDF_D2__NAND_DATA02   0xb0b1
+			MX6QDL_PAD_NANDF_D3__NAND_DATA03   0xb0b1
+			MX6QDL_PAD_NANDF_D4__NAND_DATA04   0xb0b1
+			MX6QDL_PAD_NANDF_D5__NAND_DATA05   0xb0b1
+			MX6QDL_PAD_NANDF_D6__NAND_DATA06   0xb0b1
+			MX6QDL_PAD_NANDF_D7__NAND_DATA07   0xb0b1
+			MX6QDL_PAD_SD4_DAT0__NAND_DQS      0x00b1
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1
+			MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_EB2__I2C2_SCL  0x4001b8b1
+			MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_5__I2C3_SCL  0x4001b8b1
+			MX6QDL_PAD_EIM_D18__I2C3_SDA 0x4001b8b1
+			MX6QDL_PAD_GPIO_0__CCM_CLKO1	0x130b0
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
+			MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
+		>;
+	};
+
+	pinctrl_usbotg: usbotggrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_CMD__SD1_CMD    0x17070
+			MX6QDL_PAD_SD1_CLK__SD1_CLK    0x10070
+			MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x17070
+			MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17070
+			MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17070
+			MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17070
+		>;
+	};
+};

arch/arm/boot/dts/imx6qdl-nit6xlite.dtsi

@@ -97,15 +97,6 @@ reg_wlan_vmmc: regulator@3 {
 		};
 	};
 
-	bt_rfkill {
-		compatible = "rfkill-gpio";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_bt_rfkill>;
-		gpios = <&gpio6 8 GPIO_ACTIVE_HIGH>;
-		name = "bt_rfkill";
-		type = <2>;
-	};
-
 	gpio-keys {
 		compatible = "gpio-keys";
 		pinctrl-names = "default";
@@ -160,7 +151,7 @@ j46-pin3 {
 		};
 	};
 
-	backlight_lcd {
+	backlight-lcd {
 		compatible = "pwm-backlight";
 		pwms = <&pwm1 0 5000000>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
@@ -169,7 +160,7 @@ backlight_lcd {
 		status = "okay";
 	};
 
-	backlight_lvds0: backlight_lvds0 {
+	backlight_lvds0: backlight-lvds0 {
 		compatible = "pwm-backlight";
 		pwms = <&pwm4 0 5000000>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
@@ -178,7 +169,7 @@ backlight_lvds0: backlight_lvds0 {
 		status = "okay";
 	};
 
-	panel_lvds0 {
+	panel-lvds0 {
 		compatible = "hannstar,hsd100pxn1";
 		backlight = <&backlight_lvds0>;
 
@@ -328,19 +319,6 @@ MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS		0x130b0
 			>;
 		};
 
-		pinctrl_bt_rfkill: bt_rfkillgrp {
-			fsl,pins = <
-				/* BT wake */
-				MX6QDL_PAD_NANDF_D2__GPIO2_IO02		0x1b0b0
-				/* BT reset */
-				MX6QDL_PAD_NANDF_ALE__GPIO6_IO08	0x0b0b0
-				/* BT reg en */
-				MX6QDL_PAD_NANDF_CS2__GPIO6_IO15	0x1b0b0
-				/* BT host wake irq */
-				MX6QDL_PAD_NANDF_CS3__GPIO6_IO16	0x100b0
-			>;
-		};
-
 		pinctrl_ecspi1: ecspi1grp {
 			fsl,pins = <
 				MX6QDL_PAD_EIM_D17__ECSPI1_MISO		0x100b1
@@ -374,7 +352,7 @@ MX6QDL_PAD_GPIO_6__ENET_IRQ		0x000b1
 			>;
 		};
 
-		pinctrl_gpio_keys: gpio_keysgrp {
+		pinctrl_gpio_keys: gpio-keysgrp {
 			fsl,pins = <
 				/* Home Button: J14 pin 5 */
 				MX6QDL_PAD_GPIO_18__GPIO7_IO13		0x1b0b0
@@ -457,7 +435,7 @@ MX6QDL_PAD_SD1_CMD__PWM4_OUT		0x1b0b1
 			>;
 		};
 
-		pinctrl_wlan_vmmc: wlan_vmmcgrp {
+		pinctrl_wlan_vmmc: wlan-vmmcgrp {
 			fsl,pins = <
 				MX6QDL_PAD_NANDF_CLE__GPIO6_IO07	0x030b0
 			>;

arch/arm/boot/dts/imx6qdl-nitrogen6_max.dtsi

@@ -229,7 +229,7 @@ ttymxc4-rs232 {
 		};
 	};
 
-	backlight_lcd: backlight_lcd {
+	backlight_lcd: backlight-lcd {
 		compatible = "pwm-backlight";
 		pwms = <&pwm1 0 5000000>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
@@ -238,7 +238,7 @@ backlight_lcd: backlight_lcd {
 		status = "okay";
 	};
 
-	backlight_lvds0: backlight_lvds0 {
+	backlight_lvds0: backlight-lvds0 {
 		compatible = "pwm-backlight";
 		pwms = <&pwm4 0 5000000>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
@@ -247,7 +247,7 @@ backlight_lvds0: backlight_lvds0 {
 		status = "okay";
 	};
 
-	backlight_lvds1: backlight_lvds1 {
+	backlight_lvds1: backlight-lvds1 {
 		compatible = "pwm-backlight";
 		pwms = <&pwm2 0 5000000>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
@@ -282,7 +282,7 @@ lcd_display_out: endpoint {
 		};
 	};
 
-	panel_lcd {
+	panel-lcd {
 		compatible = "okaya,rs800480t-7x0gp";
 		backlight = <&backlight_lcd>;
 
@@ -293,7 +293,7 @@ lcd_panel_in: endpoint {
 		};
 	};
 
-	panel_lvds0 {
+	panel-lvds0 {
 		compatible = "hannstar,hsd100pxn1";
 		backlight = <&backlight_lvds0>;
 
@@ -304,7 +304,7 @@ panel_in_lvds0: endpoint {
 		};
 	};
 
-	panel_lvds1 {
+	panel-lvds1 {
 		compatible = "hannstar,hsd100pxn1";
 		backlight = <&backlight_lvds1>;
 
@@ -447,7 +447,7 @@ touchscreen@38 {
 };
 
 &iomuxc {
-	imx6q-nitrogen6_max {
+	imx6q-nitrogen6-max {
 		pinctrl_audmux: audmuxgrp {
 			fsl,pins = <
 				MX6QDL_PAD_CSI0_DAT7__AUD3_RXD		0x130b0
@@ -504,7 +504,7 @@ MX6QDL_PAD_GPIO_6__ENET_IRQ		0x000b1
 			>;
 		};
 
-		pinctrl_gpio_keys: gpio_keysgrp {
+		pinctrl_gpio_keys: gpio-keysgrp {
 			fsl,pins = <
 				/* Power Button */
 				MX6QDL_PAD_NANDF_D3__GPIO2_IO03		0x1b0b0
@@ -720,7 +720,7 @@ MX6QDL_PAD_SD4_DAT7__SD4_DATA7		0x17059
 			>;
 		};
 
-		pinctrl_wlan_vmmc: wlan_vmmcgrp {
+		pinctrl_wlan_vmmc: wlan-vmmcgrp {
 			fsl,pins = <
 				MX6QDL_PAD_NANDF_CS0__GPIO6_IO11	0x100b0
 				MX6QDL_PAD_NANDF_CS2__GPIO6_IO15	0x000b0

arch/arm/boot/dts/imx6qdl-nitrogen6x.dtsi

@@ -167,7 +167,7 @@ sound {
 		mux-ext-port = <3>;
 	};
 
-	backlight_lcd: backlight_lcd {
+	backlight_lcd: backlight-lcd {
 		compatible = "pwm-backlight";
 		pwms = <&pwm1 0 5000000>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
@@ -176,7 +176,7 @@ backlight_lcd: backlight_lcd {
 		status = "okay";
 	};
 
-	backlight_lvds: backlight_lvds {
+	backlight_lvds: backlight-lvds {
 		compatible = "pwm-backlight";
 		pwms = <&pwm4 0 5000000>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
@@ -211,7 +211,7 @@ lcd_display_out: endpoint {
 		};
 	};
 
-	lcd_panel {
+	panel-lcd {
 		compatible = "okaya,rs800480t-7x0gp";
 		backlight = <&backlight_lcd>;
 
@@ -222,7 +222,7 @@ lcd_panel_in: endpoint {
 		};
 	};
 
-	panel {
+	panel-lvds0 {
 		compatible = "hannstar,hsd100pxn1";
 		backlight = <&backlight_lvds>;
 
@@ -413,7 +413,7 @@ MX6QDL_PAD_GPIO_6__ENET_IRQ		0x000b1
 			>;
 		};
 
-		pinctrl_gpio_keys: gpio_keysgrp {
+		pinctrl_gpio_keys: gpio-keysgrp {
 			fsl,pins = <
 				/* Power Button */
 				MX6QDL_PAD_NANDF_D3__GPIO2_IO03		0x1b0b0
@@ -561,7 +561,7 @@ MX6QDL_PAD_NANDF_D6__GPIO2_IO06 0x1b0b0	/* CD */
 			>;
 		};
 
-		pinctrl_wlan_vmmc: wlan_vmmcgrp {
+		pinctrl_wlan_vmmc: wlan-vmmcgrp {
 			fsl,pins = <
 				MX6QDL_PAD_NANDF_CS0__GPIO6_IO11	0x100b0
 				MX6QDL_PAD_NANDF_CS2__GPIO6_IO15	0x000b0

arch/arm/boot/dts/imx6qdl-sabreauto.dtsi

@@ -613,8 +613,6 @@ &usdhc3 {
 &weim {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_weim_nor &pinctrl_weim_cs0>;
-	#address-cells = <2>;
-	#size-cells = <1>;
 	ranges = <0 0 0x08000000 0x08000000>;
 	status = "disabled"; /* pin conflict with SPI NOR */
 

arch/arm/boot/dts/imx6qdl-sabrelite.dtsi

@@ -153,7 +153,7 @@ sound {
 		mux-ext-port = <4>;
 	};
 
-	backlight_lcd: backlight_lcd {
+	backlight_lcd: backlight-lcd {
 		compatible = "pwm-backlight";
 		pwms = <&pwm1 0 5000000>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
@@ -162,7 +162,7 @@ backlight_lcd: backlight_lcd {
 		status = "okay";
 	};
 
-	backlight_lvds: backlight_lvds {
+	backlight_lvds: backlight-lvds {
 		compatible = "pwm-backlight";
 		pwms = <&pwm4 0 5000000>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
@@ -197,7 +197,7 @@ lcd_display_out: endpoint {
 		};
 	};
 
-	lcd_panel {
+	panel-lcd {
 		compatible = "okaya,rs800480t-7x0gp";
 		backlight = <&backlight_lcd>;
 
@@ -208,7 +208,7 @@ lcd_panel_in: endpoint {
 		};
 	};
 
-	panel {
+	panel-lvds0 {
 		compatible = "hannstar,hsd100pxn1";
 		backlight = <&backlight_lvds>;
 
@@ -378,7 +378,7 @@ MX6QDL_PAD_GPIO_6__ENET_IRQ		0x000b1
 			>;
 		};
 
-		pinctrl_gpio_keys: gpio_keysgrp {
+		pinctrl_gpio_keys: gpio-keysgrp {
 			fsl,pins = <
 				/* Power Button */
 				MX6QDL_PAD_NANDF_D3__GPIO2_IO03		0x1b0b0

arch/arm/boot/dts/imx6qdl.dtsi

@@ -13,9 +13,10 @@
 #include <dt-bindings/clock/imx6qdl-clock.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 
-#include "skeleton.dtsi"
-
 / {
+	#address-cells = <1>;
+	#size-cells = <1>;
+
 	aliases {
 		ethernet0 = &fec;
 		can0 = &can1;
@@ -1092,10 +1093,13 @@ mmdc1: mmdc@021b4000 { /* MMDC1 */
 			};
 
 			weim: weim@021b8000 {
+				#address-cells = <2>;
+				#size-cells = <1>;
 				compatible = "fsl,imx6q-weim";
 				reg = <0x021b8000 0x4000>;
 				interrupts = <0 14 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX6QDL_CLK_EIM_SLOW>;
+				fsl,weim-cs-gpr = <&gpr>;
 			};
 
 			ocotp: ocotp@021bc000 {

arch/arm/boot/dts/imx6qp.dtsi

@@ -85,5 +85,12 @@ ipu2: ipu@02800000 {
 		pcie: pcie@0x01000000 {
 			compatible = "fsl,imx6qp-pcie", "snps,dw-pcie";
 		};
+
+		aips-bus@02100000 {
+			mmdc0: mmdc@021b0000 { /* MMDC0 */
+				compatible = "fsl,imx6qp-mmdc", "fsl,imx6q-mmdc";
+				reg = <0x021b0000 0x4000>;
+			};
+		};
 	};
 };

arch/arm/boot/dts/imx6sl.dtsi

@@ -8,11 +8,13 @@
  */
 
 #include <dt-bindings/interrupt-controller/irq.h>
-#include "skeleton.dtsi"
 #include "imx6sl-pinfunc.h"
 #include <dt-bindings/clock/imx6sl-clock.h>
 
 / {
+	#address-cells = <1>;
+	#size-cells = <1>;
+
 	aliases {
 		ethernet0 = &fec;
 		gpio0 = &gpio1;
@@ -893,8 +895,11 @@ rngb: rngb@021b4000 {
 			};
 
 			weim: weim@021b8000 {
+				#address-cells = <2>;
+				#size-cells = <1>;
 				reg = <0x021b8000 0x4000>;
 				interrupts = <0 14 IRQ_TYPE_LEVEL_HIGH>;
+				fsl,weim-cs-gpr = <&gpr>;
 			};
 
 			ocotp: ocotp@021bc000 {

arch/arm/boot/dts/imx6sx-sdb.dtsi

@@ -290,6 +290,14 @@ &usbotg2 {
 	status = "okay";
 };
 
+&usbphy1 {
+	fsl,tx-d-cal = <106>;
+};
+
+&usbphy2 {
+	fsl,tx-d-cal = <106>;
+};
+
 &usdhc2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc2>;

arch/arm/boot/dts/imx6sx-udoo-neo-basic.dts

+/*
+ * Copyright (c) 2016 Andreas Färber
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This library is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This library is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "imx6sx-udoo-neo.dtsi"
+
+/ {
+	model = "UDOO Neo Basic";
+	compatible = "udoo,neobasic", "fsl,imx6sx";
+
+	memory {
+		reg = <0x80000000 0x20000000>;
+	};
+};
+
+&fec1 {
+	phy-handle = <&ethphy1>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy1: ethernet-phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <0>;
+		};
+	};
+};

arch/arm/boot/dts/imx6sx-udoo-neo-extended.dts

+/*
+ * Copyright (c) 2016 Andreas Färber
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This library is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This library is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "imx6sx-udoo-neo.dtsi"
+
+/ {
+	model = "UDOO Neo Extended";
+	compatible = "udoo,neoextended", "fsl,imx6sx";
+
+	memory {
+		reg = <0x80000000 0x40000000>;
+	};
+};

arch/arm/boot/dts/imx6sx-udoo-neo-full.dts

+/*
+ * Copyright (c) 2016 Andreas Färber
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This library is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This library is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "imx6sx-udoo-neo.dtsi"
+
+/ {
+	model = "UDOO Neo Full";
+	compatible = "udoo,neofull", "fsl,imx6sx";
+
+	memory {
+		reg = <0x80000000 0x40000000>;
+	};
+};
+
+&fec1 {
+	phy-handle = <&ethphy1>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy1: ethernet-phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <0>;
+		};
+	};
+};

arch/arm/boot/dts/imx6sx-udoo-neo.dtsi

+/*
+ * Copyright (c) 2016 Andreas Färber
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This library is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This library is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "imx6sx.dtsi"
+
+/ {
+	compatible = "fsl,imx6sx";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		red {
+			label = "udoo-neo:red:mmc";
+			gpios = <&gpio6 0 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+			linux,default-trigger = "mmc0";
+		};
+
+		orange {
+			label = "udoo-neo:orange:user";
+			gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>;
+			default-state = "keep";
+		};
+	};
+
+	reg_sdio_pwr: regulator-sdio-pwr {
+		compatible = "regulator-fixed";
+		gpio = <&gpio6 1 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-name = "SDIO_PWR";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+	};
+};
+
+&cpu0 {
+	arm-supply = <&sw1a_reg>;
+	soc-supply = <&sw1c_reg>;
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet1>;
+	phy-mode = "rmii";
+	phy-reset-gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	clock-frequency = <100000>;
+	status = "okay";
+
+	pmic: pmic@08 {
+		compatible = "fsl,pfuze3000";
+		reg = <0x08>;
+
+		regulators {
+			sw1a_reg: sw1a {
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1475000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <6250>;
+			};
+
+			sw1c_reg: sw1b {
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1475000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <6250>;
+			};
+
+			sw2_reg: sw2 {
+				regulator-min-microvolt = <1500000>;
+				regulator-max-microvolt = <1850000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw3a_reg: sw3 {
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1650000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			swbst_reg: swbst {
+				regulator-min-microvolt = <5000000>;
+				regulator-max-microvolt = <5150000>;
+			};
+
+			snvs_reg: vsnvs {
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vref_reg: vrefddr {
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vgen1_reg: vldo1 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen2_reg: vldo2 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+			};
+
+			vgen3_reg: vccsd {
+				regulator-min-microvolt = <2850000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen4_reg: v33 {
+				regulator-min-microvolt = <2850000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen5_reg: vldo3 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen6_reg: vldo4 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+		};
+	};
+};
+
+&iomuxc {
+	pinctrl_enet1: enet1grp {
+		fsl,pins =
+			<MX6SX_PAD_ENET1_CRS__GPIO2_IO_1	0xa0b1>,
+			<MX6SX_PAD_ENET1_MDC__ENET1_MDC		0xa0b1>,
+			<MX6SX_PAD_ENET1_MDIO__ENET1_MDIO	0xa0b1>,
+			<MX6SX_PAD_RGMII1_TD0__ENET1_TX_DATA_0	0xa0b1>,
+			<MX6SX_PAD_RGMII1_TD1__ENET1_TX_DATA_1	0xa0b1>,
+			<MX6SX_PAD_RGMII1_TX_CTL__ENET1_TX_EN	0xa0b1>,
+
+			<MX6SX_PAD_ENET1_TX_CLK__ENET1_REF_CLK1	0x3081>,
+			<MX6SX_PAD_ENET2_TX_CLK__GPIO2_IO_9	0x3081>,
+			<MX6SX_PAD_RGMII1_RD0__ENET1_RX_DATA_0	0x3081>,
+			<MX6SX_PAD_RGMII1_RD1__ENET1_RX_DATA_1	0x3081>,
+			<MX6SX_PAD_RGMII1_RX_CTL__ENET1_RX_EN	0x3081>,
+			<MX6SX_PAD_RGMII1_RXC__ENET1_RX_ER	0x3081>,
+
+			<MX6SX_PAD_ENET2_RX_CLK__ENET2_REF_CLK_25M	0x91>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins =
+			<MX6SX_PAD_GPIO1_IO00__I2C1_SCL		0x4001b8b1>,
+			<MX6SX_PAD_GPIO1_IO01__I2C1_SDA		0x4001b8b1>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins =
+			<MX6SX_PAD_GPIO1_IO04__UART1_TX		0x1b0b1>,
+			<MX6SX_PAD_GPIO1_IO05__UART1_RX		0x1b0b1>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins =
+			<MX6SX_PAD_GPIO1_IO06__UART2_TX		0x1b0b1>,
+			<MX6SX_PAD_GPIO1_IO07__UART2_RX		0x1b0b1>;
+	};
+
+	pinctrl_uart5: uart5grp {
+		fsl,pins =
+			<MX6SX_PAD_SD4_DATA4__UART5_RX		0x1b0b1>,
+			<MX6SX_PAD_SD4_DATA5__UART5_TX		0x1b0b1>;
+	};
+
+	pinctrl_uart6: uart6grp {
+		fsl,pins =
+			<MX6SX_PAD_CSI_DATA00__UART6_RI_B	0x1b0b1>,
+			<MX6SX_PAD_CSI_DATA01__UART6_DSR_B	0x1b0b1>,
+			<MX6SX_PAD_CSI_DATA02__UART6_DTR_B	0x1b0b1>,
+			<MX6SX_PAD_CSI_DATA03__UART6_DCD_B	0x1b0b1>,
+			<MX6SX_PAD_CSI_DATA04__UART6_RX		0x1b0b1>,
+			<MX6SX_PAD_CSI_DATA05__UART6_TX		0x1b0b1>,
+			<MX6SX_PAD_CSI_DATA06__UART6_RTS_B	0x1b0b1>,
+			<MX6SX_PAD_CSI_DATA07__UART6_CTS_B	0x1b0b1>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins =
+			<MX6SX_PAD_SD2_CMD__USDHC2_CMD		0x17059>,
+			<MX6SX_PAD_SD2_CLK__USDHC2_CLK		0x10059>,
+			<MX6SX_PAD_SD2_DATA0__USDHC2_DATA0	0x17059>,
+			<MX6SX_PAD_SD2_DATA1__USDHC2_DATA1	0x17059>,
+			<MX6SX_PAD_SD2_DATA2__USDHC2_DATA2	0x17059>,
+			<MX6SX_PAD_SD2_DATA3__USDHC2_DATA3	0x17059>,
+			<MX6SX_PAD_SD1_DATA0__GPIO6_IO_2	0x17059>; /* CD */
+	};
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+/* Cortex-M4 serial */
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "disabled";
+};
+
+/* Arduino serial */
+&uart5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart5>;
+	status = "disabled";
+};
+
+&uart6 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart6>;
+	uart-has-rtscts;
+	status = "disabled";
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	vmmc-supply = <&reg_sdio_pwr>;
+	bus-width = <4>;
+	cd-gpios = <&gpio6 2 GPIO_ACTIVE_LOW>;
+	no-1-8-v;
+	keep-power-in-suspend;
+	wakeup-source;
+	status = "okay";
+};

arch/arm/boot/dts/imx6sx.dtsi

@@ -11,9 +11,11 @@
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include "imx6sx-pinfunc.h"
-#include "skeleton.dtsi"
 
 / {
+	#address-cells = <1>;
+	#size-cells = <1>;
+
 	aliases {
 		can0 = &flexcan1;
 		can1 = &flexcan2;
@@ -968,10 +970,13 @@ fec2: ethernet@021b4000 {
 			};
 
 			weim: weim@021b8000 {
+				#address-cells = <2>;
+				#size-cells = <1>;
 				compatible = "fsl,imx6sx-weim", "fsl,imx6q-weim";
 				reg = <0x021b8000 0x4000>;
 				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX6SX_CLK_EIM_SLOW>;
+				fsl,weim-cs-gpr = <&gpr>;
 			};
 
 			ocotp: ocotp@021bc000 {
@@ -1143,7 +1148,7 @@ csi2: csi@0221c000 {
 				lcdif1: lcdif@02220000 {
 					compatible = "fsl,imx6sx-lcdif", "fsl,imx28-lcdif";
 					reg = <0x02220000 0x4000>;
-					interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
+					interrupts = <GIC_SPI 5 IRQ_TYPE_EDGE_RISING>;
 					clocks = <&clks IMX6SX_CLK_LCDIF1_PIX>,
 						 <&clks IMX6SX_CLK_LCDIF_APB>,
 						 <&clks IMX6SX_CLK_DISPLAY_AXI>;
@@ -1154,7 +1159,7 @@ lcdif1: lcdif@02220000 {
 				lcdif2: lcdif@02224000 {
 					compatible = "fsl,imx6sx-lcdif", "fsl,imx28-lcdif";
 					reg = <0x02224000 0x4000>;
-					interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+					interrupts = <GIC_SPI 6 IRQ_TYPE_EDGE_RISING>;
 					clocks = <&clks IMX6SX_CLK_LCDIF2_PIX>,
 						 <&clks IMX6SX_CLK_LCDIF_APB>,
 						 <&clks IMX6SX_CLK_DISPLAY_AXI>;

arch/arm/boot/dts/imx6ul-14x14-evk.dts

@@ -225,7 +225,7 @@ &uart2 {
 };
 
 &usbotg1 {
-	dr_mode = "peripheral";
+	dr_mode = "otg";
 	status = "okay";
 };
 
@@ -235,6 +235,14 @@ &usbotg2 {
 	status = "okay";
 };
 
+&usbphy1 {
+	fsl,tx-d-cal = <106>;
+};
+
+&usbphy2 {
+	fsl,tx-d-cal = <106>;
+};
+
 &usdhc1 {
 	pinctrl-names = "default", "state_100mhz", "state_200mhz";
 	pinctrl-0 = <&pinctrl_usdhc1>;

arch/arm/boot/dts/imx6ul-liteboard.dts

+/*
+ * Copyright 2016 Grinn
+ *
+ * Author: Marcin Niestroj <m.niestroj@grinn-global.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License
+ *     version 2 as published by the Free Software Foundation.
+ *
+ *     This file is distributed in the hope that it will be useful
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "imx6ul-litesom.dtsi"
+
+/ {
+	model = "Grinn i.MX6UL liteBoard";
+	compatible = "grinn,imx6ul-liteboard", "grinn,imx6ul-litesom",
+		     "fsl,imx6ul";
+
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	reg_usb_otg1_vbus: regulator-usb-otg1-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usb_otg1_vbus>;
+		regulator-name = "usb_otg1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio2 8 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&iomuxc {
+	pinctrl_enet1: enet1grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO07__ENET1_MDC		0x1b0b0
+			MX6UL_PAD_GPIO1_IO06__ENET1_MDIO	0x1b0b0
+			MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN	0x1b0b0
+			MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER	0x1b0b0
+			MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00 0x1b0b0
+			MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01 0x1b0b0
+			MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN	0x1b0b0
+			MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00 0x1b0b0
+			MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01 0x1b0b0
+			MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1	0x4001b031
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX	0x1b0b1
+			MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX	0x1b0b1
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX6UL_PAD_UART1_RTS_B__GPIO1_IO19	0x17059
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x17059
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x10071
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x17059
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x17059
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x17059
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x17059
+		>;
+	};
+
+	pinctrl_usb_otg1_vbus: usb-otg1-vbus {
+		fsl,pins = <
+			MX6UL_PAD_ENET2_RX_DATA0__GPIO2_IO08	0x79
+		>;
+	};
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet1>;
+	phy-mode = "rmii";
+	phy-handle = <&ethphy0>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@0 {
+			reg = <0>;
+		};
+	};
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&usbotg1 {
+	vbus-supply = <&reg_usb_otg1_vbus>;
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
+	no-1-8-v;
+	keep-power-in-suspend;
+	wakeup-source;
+	status = "okay";
+};

arch/arm/boot/dts/imx6ul-litesom.dtsi

+/*
+ * Copyright 2016 Grinn
+ *
+ * Author: Marcin Niestroj <m.niestroj@grinn-global.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License
+ *     version 2 as published by the Free Software Foundation.
+ *
+ *     This file is distributed in the hope that it will be useful
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "imx6ul.dtsi"
+
+/ {
+	model = "Grinn i.MX6UL liteSOM";
+	compatible = "grinn,imx6ul-litesom", "fsl,imx6ul";
+
+	memory {
+		reg = <0x80000000 0x20000000>;
+	};
+};
+
+&iomuxc {
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK	    0x10069
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD	    0x17059
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x17059
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x17059
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x17059
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x17059
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x17059
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x17059
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x17059
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x17059
+			MX6UL_PAD_NAND_ALE__USDHC2_RESET_B  0x17059
+		>;
+	};
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	no-1-8-v;
+	non-removable;
+	keep-power-in-suspend;
+	wakeup-source;
+	bus-width = <8>;
+	status = "okay";
+};

arch/arm/boot/dts/imx6ul.dtsi

@@ -11,9 +11,11 @@
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include "imx6ul-pinfunc.h"
-#include "skeleton.dtsi"
 
 / {
+	#address-cells = <1>;
+	#size-cells = <1>;
+
 	aliases {
 		ethernet0 = &fec1;
 		ethernet1 = &fec2;

arch/arm/boot/dts/imx6ull-14x14-evk.dts

+/*
+ * Copyright (C) 2016 Freescale Semiconductor, Inc.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License
+ *     version 2 as published by the Free Software Foundation.
+ *
+ *     This file is distributed in the hope that it will be useful
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "imx6ul-14x14-evk.dts"
+
+/ {
+	model = "Freescale i.MX6 UlltraLite 14x14 EVK Board";
+	compatible = "fsl,imx6ull-14x14-evk", "fsl,imx6ull";
+};
+
+&clks {
+	assigned-clocks = <&clks IMX6UL_CLK_PLL3_PFD2>;
+	assigned-clock-rates = <320000000>;
+};

arch/arm/boot/dts/imx6ull-pinfunc.h

+/*
+ * Copyright (C) 2016 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __DTS_IMX6ULL_PINFUNC_H
+#define __DTS_IMX6ULL_PINFUNC_H
+
+#include "imx6ul-pinfunc.h"
+/*
+ * The pin function ID is a tuple of
+ * <mux_reg conf_reg input_reg mux_mode input_val>
+ */
+#define MX6ULL_PAD_ENET2_RX_DATA0__EPDC_SDDO08                    0x00E4 0x0370 0x0000 0x9 0x0
+#define MX6ULL_PAD_ENET2_RX_DATA1__EPDC_SDDO09                    0x00E8 0x0374 0x0000 0x9 0x0
+#define MX6ULL_PAD_ENET2_RX_EN__EPDC_SDDO10                       0x00EC 0x0378 0x0000 0x9 0x0
+#define MX6ULL_PAD_ENET2_TX_DATA0__EPDC_SDDO11                    0x00F0 0x037C 0x0000 0x9 0x0
+#define MX6ULL_PAD_ENET2_TX_DATA1__EPDC_SDDO12                    0x00F4 0x0380 0x0000 0x9 0x0
+#define MX6ULL_PAD_ENET2_TX_EN__EPDC_SDDO13                       0x00F8 0x0384 0x0000 0x9 0x0
+#define MX6ULL_PAD_ENET2_TX_CLK__EPDC_SDDO14                      0x00FC 0x0388 0x0000 0x9 0x0
+#define MX6ULL_PAD_ENET2_RX_ER__EPDC_SDDO15                       0x0100 0x038C 0x0000 0x9 0x0
+#define MX6ULL_PAD_LCD_CLK__EPDC_SDCLK                            0x0104 0x0390 0x0000 0x9 0x0
+#define MX6ULL_PAD_LCD_ENABLE__EPDC_SDLE                          0x0108 0x0394 0x0000 0x9 0x0
+#define MX6ULL_PAD_LCD_HSYNC__EPDC_SDOE                           0x010C 0x0398 0x0000 0x9 0x0
+#define MX6ULL_PAD_LCD_VSYNC__EPDC_SDCE0                          0x0110 0x039C 0x0000 0x9 0x0
+#define MX6ULL_PAD_LCD_RESET__EPDC_GDOE                           0x0114 0x03A0 0x0000 0x9 0x0
+#define MX6ULL_PAD_LCD_DATA00__EPDC_SDDO00                        0x0118 0x03A4 0x0000 0x9 0x0
+#define MX6ULL_PAD_LCD_DATA01__EPDC_SDDO01                        0x011C 0x03A8 0x0000 0x9 0x0
+#define MX6ULL_PAD_LCD_DATA02__EPDC_SDDO02                        0x0120 0x03AC 0x0000 0x9 0x0
+#define MX6ULL_PAD_LCD_DATA03__EPDC_SDDO03                        0x0124 0x03B0 0x0000 0x9 0x0
+#define MX6ULL_PAD_LCD_DATA04__EPDC_SDDO04                        0x0128 0x03B4 0x0000 0x9 0x0
+#define MX6ULL_PAD_LCD_DATA05__EPDC_SDDO05                        0x012C 0x03B8 0x0000 0x9 0x0
+#define MX6ULL_PAD_LCD_DATA06__EPDC_SDDO06                        0x0130 0x03BC 0x0000 0x9 0x0
+#define MX6ULL_PAD_LCD_DATA07__EPDC_SDDO07                        0x0134 0x03C0 0x0000 0x9 0x0
+#define MX6ULL_PAD_LCD_DATA14__EPDC_SDSHR                         0x0150 0x03DC 0x0000 0x9 0x0
+#define MX6ULL_PAD_LCD_DATA15__EPDC_GDRL                          0x0154 0x03E0 0x0000 0x9 0x0
+#define MX6ULL_PAD_LCD_DATA16__EPDC_GDCLK                         0x0158 0x03E4 0x0000 0x9 0x0
+#define MX6ULL_PAD_LCD_DATA17__EPDC_GDSP                          0x015C 0x03E8 0x0000 0x9 0x0
+#define MX6ULL_PAD_LCD_DATA21__EPDC_SDCE1                         0x016C 0x03F8 0x0000 0x9 0x0
+#define MX6ULL_PAD_CSI_MCLK__ESAI_TX3_RX2                         0x01D4 0x0460 0x0000 0x9 0x0
+#define MX6ULL_PAD_CSI_PIXCLK__ESAI_TX2_RX3                       0x01D8 0x0464 0x0000 0x9 0x0
+#define MX6ULL_PAD_CSI_VSYNC__ESAI_TX4_RX1                        0x01DC 0x0468 0x0000 0x9 0x0
+#define MX6ULL_PAD_CSI_HSYNC__ESAI_TX1                            0x01E0 0x046C 0x0000 0x9 0x0
+#define MX6ULL_PAD_CSI_DATA00__ESAI_TX_HF_CLK                     0x01E4 0x0470 0x0000 0x9 0x0
+#define MX6ULL_PAD_CSI_DATA01__ESAI_RX_HF_CLK                     0x01E8 0x0474 0x0000 0x9 0x0
+#define MX6ULL_PAD_CSI_DATA02__ESAI_RX_FS                         0x01EC 0x0478 0x0000 0x9 0x0
+#define MX6ULL_PAD_CSI_DATA03__ESAI_RX_CLK                        0x01F0 0x047C 0x0000 0x9 0x0
+#define MX6ULL_PAD_CSI_DATA04__ESAI_TX_FS                         0x01F4 0x0480 0x0000 0x9 0x0
+#define MX6ULL_PAD_CSI_DATA05__ESAI_TX_CLK                        0x01F8 0x0484 0x0000 0x9 0x0
+#define MX6ULL_PAD_CSI_DATA06__ESAI_TX5_RX0                       0x01FC 0x0488 0x0000 0x9 0x0
+#define MX6ULL_PAD_CSI_DATA07__ESAI_T0                            0x0200 0x048C 0x0000 0x9 0x0
+
+#endif /* __DTS_IMX6ULL_PINFUNC_H */

arch/arm/boot/dts/imx6ull.dtsi

+/*
+ * Copyright 2016 Freescale Semiconductor, Inc.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License
+ *     version 2 as published by the Free Software Foundation.
+ *
+ *     This file is distributed in the hope that it will be useful
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "imx6ul.dtsi"
+#include "imx6ull-pinfunc.h"

arch/arm/boot/dts/imx7s.dtsi

@@ -46,9 +46,11 @@
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include "imx7d-pinfunc.h"
-#include "skeleton.dtsi"
 
 / {
+	#address-cells = <1>;
+	#size-cells = <1>;
+
 	aliases {
 		gpio0 = &gpio1;
 		gpio1 = &gpio2;

arch/arm/boot/dts/ls1021a.dtsi

@@ -47,6 +47,7 @@
 
 #include "skeleton64.dtsi"
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/thermal/thermal.h>
 
 / {
 	compatible = "fsl,ls1021a";
@@ -70,14 +71,15 @@ cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		cpu@f00 {
+		cpu0: cpu@f00 {
 			compatible = "arm,cortex-a7";
 			device_type = "cpu";
 			reg = <0xf00>;
 			clocks = <&cluster1_clk>;
+			#cooling-cells = <2>;
 		};
 
-		cpu@f01 {
+		cpu1: cpu@f01 {
 			compatible = "arm,cortex-a7";
 			device_type = "cpu";
 			reg = <0xf01>;
@@ -251,6 +253,84 @@ cluster1_clk: clk0c0@0 {
 			};
 		};
 
+		tmu: tmu@1f00000 {
+			compatible = "fsl,qoriq-tmu";
+			reg = <0x0 0x1f00000 0x0 0x10000>;
+			interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
+			fsl,tmu-range = <0xb0000 0xa0026 0x80048 0x30061>;
+			fsl,tmu-calibration = <0x00000000 0x0000000f
+					       0x00000001 0x00000017
+					       0x00000002 0x0000001e
+					       0x00000003 0x00000026
+					       0x00000004 0x0000002e
+					       0x00000005 0x00000035
+					       0x00000006 0x0000003d
+					       0x00000007 0x00000044
+					       0x00000008 0x0000004c
+					       0x00000009 0x00000053
+					       0x0000000a 0x0000005b
+					       0x0000000b 0x00000064
+
+					       0x00010000 0x00000011
+					       0x00010001 0x0000001c
+					       0x00010002 0x00000024
+					       0x00010003 0x0000002b
+					       0x00010004 0x00000034
+					       0x00010005 0x00000039
+					       0x00010006 0x00000042
+					       0x00010007 0x0000004c
+					       0x00010008 0x00000051
+					       0x00010009 0x0000005a
+					       0x0001000a 0x00000063
+
+					       0x00020000 0x00000013
+					       0x00020001 0x00000019
+					       0x00020002 0x00000024
+					       0x00020003 0x0000002c
+					       0x00020004 0x00000035
+					       0x00020005 0x0000003d
+					       0x00020006 0x00000046
+					       0x00020007 0x00000050
+					       0x00020008 0x00000059
+
+					       0x00030000 0x00000002
+					       0x00030001 0x0000000d
+					       0x00030002 0x00000019
+					       0x00030003 0x00000024>;
+			#thermal-sensor-cells = <1>;
+		};
+
+		thermal-zones {
+			cpu_thermal: cpu-thermal {
+				polling-delay-passive = <1000>;
+				polling-delay = <5000>;
+
+				thermal-sensors = <&tmu 0>;
+
+				trips {
+					cpu_alert: cpu-alert {
+						temperature = <85000>;
+						hysteresis = <2000>;
+						type = "passive";
+					};
+					cpu_crit: cpu-crit {
+						temperature = <95000>;
+						hysteresis = <2000>;
+						type = "critical";
+					};
+				};
+
+				cooling-maps {
+					map0 {
+						trip = <&cpu_alert>;
+						cooling-device =
+							<&cpu0 THERMAL_NO_LIMIT
+							THERMAL_NO_LIMIT>;
+					};
+				};
+			};
+		};
+
 		dspi0: dspi@2100000 {
 			compatible = "fsl,ls1021a-v1.0-dspi";
 			#address-cells = <1>;

arch/arm/boot/dts/vf-colibri.dtsi

@@ -108,6 +108,10 @@ &edma0 {
 	status = "okay";
 };
 
+&edma1 {
+	status = "okay";
+};
+
 &esdhc1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_esdhc1>;

arch/arm/boot/dts/vf610-zii-dev-rev-b.dts

@@ -499,13 +499,6 @@ i2c@4 {
 	};
 };
 
-&i2c3 {
-	clock-frequency = <100000>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c3>;
-	status = "okay";
-};
-
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart0>;
@@ -663,13 +656,6 @@ VF610_PAD_PTA23__I2C2_SDA	0x37ff
 		>;
 	};
 
-	pinctrl_i2c3: i2c3grp {
-		fsl,pins = <
-			VF610_PAD_PTA30__I2C3_SCL	0x37ff
-			VF610_PAD_PTA31__I2C3_SDA	0x37ff
-		>;
-	};
-
 	pinctrl_leds_debug: pinctrl-leds-debug {
 		fsl,pins = <
 			 VF610_PAD_PTD20__GPIO_74	0x31c2

arch/arm/boot/dts/vfxxx.dtsi

@@ -194,6 +194,9 @@ dspi0: dspi0@4002c000 {
 				clocks = <&clks VF610_CLK_DSPI0>;
 				clock-names = "dspi";
 				spi-num-chipselects = <6>;
+				dmas = <&edma1 1 12>,
+					<&edma1 1 13>;
+				dma-names = "rx", "tx";
 				status = "disabled";
 			};
 
@@ -206,6 +209,9 @@ dspi1: dspi1@4002d000 {
 				clocks = <&clks VF610_CLK_DSPI1>;
 				clock-names = "dspi";
 				spi-num-chipselects = <4>;
+				dmas = <&edma1 1 14>,
+					<&edma1 1 15>;
+				dma-names = "rx", "tx";
 				status = "disabled";
 			};
 
@@ -520,6 +526,12 @@ edma1: dma-controller@40098000 {
 				status = "disabled";
 			};
 
+			ocotp: ocotp@400a5000 {
+				compatible = "fsl,vf610-ocotp";
+				reg = <0x400a5000 0x1000>;
+				clocks = <&clks VF610_CLK_OCOTP>;
+			};
+
 			snvs0: snvs@400a7000 {
 			    compatible = "fsl,sec-v4.0-mon", "syscon", "simple-mfd";
 				reg = <0x400a7000 0x2000>;
@@ -561,6 +573,9 @@ dspi2: dspi2@400ac000 {
 				clocks = <&clks VF610_CLK_DSPI2>;
 				clock-names = "dspi";
 				spi-num-chipselects = <2>;
+				dmas = <&edma1 0 10>,
+					<&edma1 0 11>;
+				dma-names = "rx", "tx";
 				status = "disabled";
 			};
 
@@ -573,6 +588,9 @@ dspi3: dspi3@400ad000 {
 				clocks = <&clks VF610_CLK_DSPI3>;
 				clock-names = "dspi";
 				spi-num-chipselects = <2>;
+				dmas = <&edma1 0 12>,
+					<&edma1 0 13>;
+				dma-names = "rx", "tx";
 				status = "disabled";
 			};