Commit 2c3c5f8c authored by Andrew Zaborowski's avatar Andrew Zaborowski Committed by Johannes Berg

mac80211: Add set_cqm_rssi_range_config

Support .set_cqm_rssi_range_config if the beacons are available for
processing in mac80211.  There's no reason that this couldn't be
offloaded by mac80211-based drivers but there's no driver method for
that added in this patch.
Signed-off-by: default avatarAndrew Zaborowski <andrew.zaborowski@intel.com>
Signed-off-by: default avatarJohannes Berg <johannes.berg@intel.com>
parent 4a4b8169
......@@ -501,6 +501,10 @@ struct ieee80211_mu_group_data {
* implies disabled. As with the cfg80211 callback, a change here should
* cause an event to be sent indicating where the current value is in
* relation to the newly configured threshold.
* @cqm_rssi_low: Connection quality monitor RSSI lower threshold, a zero value
* implies disabled. This is an alternative mechanism to the single
* threshold event and can't be enabled simultaneously with it.
* @cqm_rssi_high: Connection quality monitor RSSI upper threshold.
* @cqm_rssi_hyst: Connection quality monitor RSSI hysteresis
* @arp_addr_list: List of IPv4 addresses for hardware ARP filtering. The
* may filter ARP queries targeted for other addresses than listed here.
......@@ -553,6 +557,8 @@ struct ieee80211_bss_conf {
u16 ht_operation_mode;
s32 cqm_rssi_thold;
u32 cqm_rssi_hyst;
s32 cqm_rssi_low;
s32 cqm_rssi_high;
struct cfg80211_chan_def chandef;
struct ieee80211_mu_group_data mu_group;
__be32 arp_addr_list[IEEE80211_BSS_ARP_ADDR_LIST_LEN];
......
......@@ -2630,6 +2630,33 @@ static int ieee80211_set_cqm_rssi_config(struct wiphy *wiphy,
bss_conf->cqm_rssi_thold = rssi_thold;
bss_conf->cqm_rssi_hyst = rssi_hyst;
bss_conf->cqm_rssi_low = 0;
bss_conf->cqm_rssi_high = 0;
sdata->u.mgd.last_cqm_event_signal = 0;
/* tell the driver upon association, unless already associated */
if (sdata->u.mgd.associated &&
sdata->vif.driver_flags & IEEE80211_VIF_SUPPORTS_CQM_RSSI)
ieee80211_bss_info_change_notify(sdata, BSS_CHANGED_CQM);
return 0;
}
static int ieee80211_set_cqm_rssi_range_config(struct wiphy *wiphy,
struct net_device *dev,
s32 rssi_low, s32 rssi_high)
{
struct ieee80211_sub_if_data *sdata = IEEE80211_DEV_TO_SUB_IF(dev);
struct ieee80211_vif *vif = &sdata->vif;
struct ieee80211_bss_conf *bss_conf = &vif->bss_conf;
if (sdata->vif.driver_flags & IEEE80211_VIF_BEACON_FILTER)
return -EOPNOTSUPP;
bss_conf->cqm_rssi_low = rssi_low;
bss_conf->cqm_rssi_high = rssi_high;
bss_conf->cqm_rssi_thold = 0;
bss_conf->cqm_rssi_hyst = 0;
sdata->u.mgd.last_cqm_event_signal = 0;
/* tell the driver upon association, unless already associated */
......@@ -3639,6 +3666,7 @@ const struct cfg80211_ops mac80211_config_ops = {
.mgmt_tx = ieee80211_mgmt_tx,
.mgmt_tx_cancel_wait = ieee80211_mgmt_tx_cancel_wait,
.set_cqm_rssi_config = ieee80211_set_cqm_rssi_config,
.set_cqm_rssi_range_config = ieee80211_set_cqm_rssi_range_config,
.mgmt_frame_register = ieee80211_mgmt_frame_register,
.set_antenna = ieee80211_set_antenna,
.get_antenna = ieee80211_get_antenna,
......
......@@ -3430,6 +3430,30 @@ static void ieee80211_rx_mgmt_beacon(struct ieee80211_sub_if_data *sdata,
}
}
if (bss_conf->cqm_rssi_low &&
ifmgd->count_beacon_signal >= IEEE80211_SIGNAL_AVE_MIN_COUNT) {
int sig = -ewma_beacon_signal_read(&ifmgd->ave_beacon_signal);
int last_event = ifmgd->last_cqm_event_signal;
int low = bss_conf->cqm_rssi_low;
int high = bss_conf->cqm_rssi_high;
if (sig < low &&
(last_event == 0 || last_event >= low)) {
ifmgd->last_cqm_event_signal = sig;
ieee80211_cqm_rssi_notify(
&sdata->vif,
NL80211_CQM_RSSI_THRESHOLD_EVENT_LOW,
sig, GFP_KERNEL);
} else if (sig > high &&
(last_event == 0 || last_event <= high)) {
ifmgd->last_cqm_event_signal = sig;
ieee80211_cqm_rssi_notify(
&sdata->vif,
NL80211_CQM_RSSI_THRESHOLD_EVENT_HIGH,
sig, GFP_KERNEL);
}
}
if (ifmgd->flags & IEEE80211_STA_CONNECTION_POLL) {
mlme_dbg_ratelimited(sdata,
"cancelling AP probe due to a received beacon\n");
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment