Commit 2d06efdb authored by Andrew Lunn's avatar Andrew Lunn Committed by Greg Kroah-Hartman

Staging: batman-adv: updating README

Signed-off-by: default avatarMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: default avatarAndrew Lunn <andrew@lunn.ch>
Signed-off-by: default avatarGreg Kroah-Hartman <gregkh@suse.de>
parent 6d45d8df
[state: 22-03-2010]
[state: 03-05-2010]
BATMAN-ADV
----------
Batman-advanced is a new approach to wireless networking which does no longer
operate on the IP basis. Unlike B.A.T.M.A.N, which exchanges information
using UDP packets and sets routing tables, batman-advanced operates on ISO/OSI
Layer 2 only and uses and routes (or better: bridges) Ethernet Frames. It
emulates a virtual network switch of all nodes participating. Therefore all
nodes appear to be link local, thus all higher operating protocols won't be
affected by any changes within the network. You can run almost any protocol
above B.A.T.M.A.N. Advanced, prominent examples are: IPv4, IPv6, DHCP, IPX.
This is batman-advanced implemented as Linux kernel driver. It does not depend
on any network (other) driver, and can be used on wifi as well as ethernet,
Batman advanced is a new approach to wireless networking which
does no longer operate on the IP basis. Unlike the batman daemon,
which exchanges information using UDP packets and sets routing
tables, batman-advanced operates on ISO/OSI Layer 2 only and uses
and routes (or better: bridges) Ethernet Frames. It emulates a
virtual network switch of all nodes participating. Therefore all
nodes appear to be link local, thus all higher operating proto-
cols won't be affected by any changes within the network. You can
run almost any protocol above batman advanced, prominent examples
are: IPv4, IPv6, DHCP, IPX.
Batman advanced was implemented as a Linux kernel driver to re-
duce the overhead to a minimum. It does not depend on any (other)
network driver, and can be used on wifi as well as ethernet lan,
vpn, etc ... (anything with ethernet-style layer 2).
USAGE
-----
CONFIGURATION
-------------
insmod the batman-adv.ko in your kernel:
Load the batman-adv module into your kernel:
# insmod batman-adv.ko
the module is now waiting for activation. You must add some interfaces
on which batman can operate. Each interface must be added separately:
The module is now waiting for activation. You must add some in-
terfaces on which batman can operate. After loading the module
batman advanced will scan your systems interfaces to search for
compatible interfaces. Once found, it will create subfolders in
the /sys directories of each supported interface, e.g.
# echo wlan0 > /proc/net/batman-adv/interfaces
# ls /sys/class/net/eth0/batman_adv/
# iface_status mesh_iface
( # echo wlan1 > /proc/net/batman-adv/interfaces )
( # echo eth0 > /proc/net/batman-adv/interfaces )
( ... )
If an interface does not have the "batman_adv" subfolder it prob-
ably is not supported. Not supported interfaces are: loopback,
non-ethernet and batman's own interfaces.
Now batman starts broadcasting on this interface.
You can now view the table of originators (mesh participants) with:
Note: After the module was loaded it will continuously watch for
new interfaces to verify the compatibility. There is no need to
reload the module if you plug your USB wifi adapter into your ma-
chine after batman advanced was initially loaded.
# cat /proc/net/batman-adv/originators
To activate a given interface simply write "bat0" into its
"mesh_iface" file inside the batman_adv subfolder:
The module will create a new interface "bat0", which can be used as a
regular interface:
# echo bat0 > /sys/class/net/eth0/batman_adv/mesh_iface
# ifconfig bat0 inet 192.168.0.1 up
# ping 192.168.0.2
...
Repeat this step for all interfaces you wish to add. Now batman
starts using/broadcasting on this/these interface(s).
---
If you want topology visualization, your meshnode must be configured
as VIS-server:
By reading the "iface_status" file you can check its status:
# echo "server" > /proc/net/batman-adv/vis_server
# cat /sys/class/net/eth0/batman_adv/iface_status
# active
Each node is either configured as "server" or as "client" (default:
"client"). Clients send their topology data to the server next to them,
and server synchronize with other servers. If there is no server
configured (default) within the mesh, no topology information will be
transmitted. With these "synchronizing servers", there can be 1 or
more vis servers sharing the same (or at least very similar) data.
To deactivate an interface you have to write "none" into its
"mesh_iface" file:
When configured as server, you can get a topology snapshot of your mesh:
# echo none > /sys/class/net/eth0/batman_adv/mesh_iface
# cat /proc/net/batman-adv/vis_data
This raw output is intended to be easily parsable and convertable with
other tools. Have a look at the batctl README if you want a vis output
in dot or json format for instance and how those outputs could then be
visualised in an image.
All mesh wide settings can be found in batman's own interface
folder:
The raw format consists of comma seperated values per entry where each
entry is giving information about a certain source interface. Each entry
can/has to have the following values:
-> "mac" -> mac address of an originator's source interface
(each line begins with it)
-> "TQ mac value" -> src mac's link quality towards mac address of a neighbor
originator's interface which is being used for routing
-> "HNA mac" -> HNA announced by source mac
-> "PRIMARY" -> this is a primary interface
-> "SEC mac" -> secondary mac address of source (requires preceeding
-> PRIMARY)
# ls /sys/class/net/bat0/mesh/
# aggregate_ogm originators transtable_global vis_mode
# orig_interval transtable_local vis_data
The TQ value has a range from 4 to 255 with 255 being the best.
The HNA entries are showing which hosts are connected to the mesh via bat0
or being bridged into the mesh network.
The PRIMARY/SEC values are only applied on primary interfaces
---
Some of the files contain all sort of status information regard-
ing the mesh network. For example, you can view the table of
originators (mesh participants) with:
# cat /sys/class/net/bat0/mesh/originators
Other files allow to change batman's behaviour to better fit your
requirements. For instance, you can check the current originator
interval (value in milliseconds which determines how often batman
sends its broadcast packets):
# cat /sys/class/net/bat0/mesh/orig_interval
# status: 1000
and also change its value:
# echo 3000 > /sys/class/net/bat0/mesh/orig_interval
In very mobile scenarios, you might want to adjust the originator
interval to a lower value. This will make the mesh more responsive to
topology changes, but will also increase the overhead. Please make sure
that all nodes in your mesh use the same interval. The default value
is 1000 ms (1 second).
interval to a lower value. This will make the mesh more respon-
sive to topology changes, but will also increase the overhead.
USAGE
-----
To make use of your newly created mesh, batman advanced provides
a new interface "bat0" which you should use from this point on.
All interfaces added to batman advanced are not relevant any
longer because batman handles them for you. Basically, one "hands
over" the data by using the batman interface and batman will make
sure it reaches its destination.
The "bat0" interface can be used like any other regular inter-
face. It needs an IP address which can be either statically con-
figured or dynamically (by using DHCP or similar services):
# echo 1000 > /proc/net/batman-adv/orig_interval
# NodeA: ifconfig bat0 192.168.0.1
# NodeB: ifconfig bat0 192.168.0.2
# NodeB: ping 192.168.0.1
To deactivate batman, do:
Note: In order to avoid problems remove all IP addresses previ-
ously assigned to interfaces now used by batman advanced, e.g.
# ifconfig eth0 0.0.0.0
VISUALIZATION
-------------
If you want topology visualization, at least one mesh node must
be configured as VIS-server:
# echo "server" > /sys/class/net/bat0/mesh/vis_mode
Each node is either configured as "server" or as "client" (de-
fault: "client"). Clients send their topology data to the server
next to them, and server synchronize with other servers. If there
is no server configured (default) within the mesh, no topology
information will be transmitted. With these "synchronizing
servers", there can be 1 or more vis servers sharing the same (or
at least very similar) data.
When configured as server, you can get a topology snapshot of
your mesh:
# cat /sys/class/net/bat0/mesh/vis_data
This raw output is intended to be easily parsable and convertable
with other tools. Have a look at the batctl README if you want a
vis output in dot or json format for instance and how those out-
puts could then be visualised in an image.
The raw format consists of comma separated values per entry where
each entry is giving information about a certain source inter-
face. Each entry can/has to have the following values:
-> "mac" - mac address of an originator's source interface
(each line begins with it)
-> "TQ mac value" - src mac's link quality towards mac address
of a neighbor originator's interface which
is being used for routing
-> "HNA mac" - HNA announced by source mac
-> "PRIMARY" - this is a primary interface
-> "SEC mac" - secondary mac address of source
(requires preceding PRIMARY)
The TQ value has a range from 4 to 255 with 255 being the best.
The HNA entries are showing which hosts are connected to the mesh
via bat0 or being bridged into the mesh network. The PRIMARY/SEC
values are only applied on primary interfaces
# echo "" > /proc/net/batman-adv/interfaces
LOGGING/DEBUGGING
-----------------
All error messages, warnings and information messages are sent to the
kernel log. Depending on your operating system distribution this can be
read in one of a number of ways. Try using the commands: dmesg,
logread, or looking in the files /var/log/kern.log or
/var/log/syslog. All batman-adv messages are prefixed with
All error messages, warnings and information messages are sent to
the kernel log. Depending on your operating system distribution
this can be read in one of a number of ways. Try using the com-
mands: dmesg, logread, or looking in the files /var/log/kern.log
or /var/log/syslog. All batman-adv messages are prefixed with
"batman-adv:" So to see just these messages try
dmesg | grep batman-adv
# dmesg | grep batman-adv
When investigating problems with your mesh network it is sometimes
necessary to see more detail debug messages. This must be enabled when
compiling the batman-adv module. Use "make menuconfig" and enable the
When investigating problems with your mesh network it is some-
times necessary to see more detail debug messages. This must be
enabled when compiling the batman-adv module. When building bat-
man-adv as part of kernel, use "make menuconfig" and enable the
option "B.A.T.M.A.N. debugging".
The additional debug output is by default disabled. It can be enabled
either at kernel module load time or during run time. To enable debug
output at module load time, add the module parameter debug=<value>.
<value> can take one of four values.
The additional debug output is by default disabled. It can be en-
abled either at kernel modules load time or during run time. To
enable debug output at module load time, add the module parameter
debug=<value>. <value> can take one of four values.
0 - All debug output disabled
1 - Enable messages related to routing / flooding / broadcasting
......@@ -125,34 +193,36 @@ output at module load time, add the module parameter debug=<value>.
e.g.
modprobe batman-adv debug=2
# modprobe batman-adv debug=2
will load the module and enable debug messages for when routes or HNAs
change.
will load the module and enable debug messages for when routes or
HNAs change.
The debug output can also be changed at runtime using the file
/sys/module/batman-adv/parameters/debug. e.g.
echo 2 > /sys/module/batman-adv/parameters/debug
# echo 2 > /sys/module/batman-adv/parameters/debug
enables debug messages for when routes or HNAs
The debug output is sent to the kernel logs. So try dmesg, logread etc
to see the debug messages.
The debug output is sent to the kernel logs. So try dmesg, lo-
gread, etc to see the debug messages.
BATCTL
------
B.A.T.M.A.N. advanced operates on layer 2 and thus all hosts
participating in the virtual switch are completely transparent for all
protocols above layer 2. Therefore the common diagnosis tools do not
work as expected. To overcome these problems batctl was created. At
As batman advanced operates on layer 2 all hosts participating in
the virtual switch are completely transparent for all protocols
above layer 2. Therefore the common diagnosis tools do not work
as expected. To overcome these problems batctl was created. At
the moment the batctl contains ping, traceroute, tcpdump and
interfaces to the kernel module settings.
For more information, please see the manpage (man batctl).
batctl is available on http://www.open-mesh.net/
batctl is available on http://www.open-mesh.org/
CONTACT
-------
......@@ -160,10 +230,11 @@ CONTACT
Please send us comments, experiences, questions, anything :)
IRC: #batman on irc.freenode.org
Mailing-list: b.a.t.m.a.n@open-mesh.net
(subscription at https://list.open-mesh.net/mm/listinfo/b.a.t.m.a.n )
Mailing-list: b.a.t.m.a.n@open-mesh.net (optional subscription
at https://lists.open-mesh.org/mm/listinfo/b.a.t.m.a.n)
You can also contact the Authors:
Marek Lindner <lindner_marek@yahoo.de>
Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment