net: dsa: microchip: call phy_remove_link_mode during probe

When doing "ip link set dev ... up" for a ksz9477 backed link,
ksz9477_phy_setup is called and it calls phy_remove_link_mode to remove
1000baseT HDX. During phy_remove_link_mode, phy_advertise_supported is
called. Doing so reverts any previous change to advertised link modes
e.g. using a udevd .link file.

phy_remove_link_mode is not meant to be used while opening a link and
should be called during phy probe when the link is not yet available to
userspace.

Therefore move the phy_remove_link_mode calls into
ksz9477_switch_register. It indirectly calls dsa_register_switch, which
creates the relevant struct phy_devices and we update the link modes
right after that. At that time dev->features is already initialized by
ksz9477_switch_detect.

Remove phy_setup from ksz_dev_ops as no users remain.

Link: https://lore.kernel.org/netdev/20200715192722.GD1256692@lunn.ch/
Fixes: 42fc6a4c ("net: dsa: microchip: prepare PHY for proper advertisement")
Signed-off-by: Helmut Grohne <helmut.grohne@intenta.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/dsa/microchip/ksz9477.c

@@ -974,23 +974,6 @@ static void ksz9477_port_mirror_del(struct dsa_switch *ds, int port,
 			     PORT_MIRROR_SNIFFER, false);
 }
 
-static void ksz9477_phy_setup(struct ksz_device *dev, int port,
-			      struct phy_device *phy)
-{
-	/* Only apply to port with PHY. */
-	if (port >= dev->phy_port_cnt)
-		return;
-
-	/* The MAC actually cannot run in 1000 half-duplex mode. */
-	phy_remove_link_mode(phy,
-			     ETHTOOL_LINK_MODE_1000baseT_Half_BIT);
-
-	/* PHY does not support gigabit. */
-	if (!(dev->features & GBIT_SUPPORT))
-		phy_remove_link_mode(phy,
-				     ETHTOOL_LINK_MODE_1000baseT_Full_BIT);
-}
-
 static bool ksz9477_get_gbit(struct ksz_device *dev, u8 data)
 {
 	bool gbit;
@@ -1603,7 +1586,6 @@ static const struct ksz_dev_ops ksz9477_dev_ops = {
 	.get_port_addr = ksz9477_get_port_addr,
 	.cfg_port_member = ksz9477_cfg_port_member,
 	.flush_dyn_mac_table = ksz9477_flush_dyn_mac_table,
-	.phy_setup = ksz9477_phy_setup,
 	.port_setup = ksz9477_port_setup,
 	.r_mib_cnt = ksz9477_r_mib_cnt,
 	.r_mib_pkt = ksz9477_r_mib_pkt,
@@ -1617,7 +1599,29 @@ static const struct ksz_dev_ops ksz9477_dev_ops = {
 
 int ksz9477_switch_register(struct ksz_device *dev)
 {
-	return ksz_switch_register(dev, &ksz9477_dev_ops);
+	int ret, i;
+	struct phy_device *phydev;
+
+	ret = ksz_switch_register(dev, &ksz9477_dev_ops);
+	if (ret)
+		return ret;
+
+	for (i = 0; i < dev->phy_port_cnt; ++i) {
+		if (!dsa_is_user_port(dev->ds, i))
+			continue;
+
+		phydev = dsa_to_port(dev->ds, i)->slave->phydev;
+
+		/* The MAC actually cannot run in 1000 half-duplex mode. */
+		phy_remove_link_mode(phydev,
+				     ETHTOOL_LINK_MODE_1000baseT_Half_BIT);
+
+		/* PHY does not support gigabit. */
+		if (!(dev->features & GBIT_SUPPORT))
+			phy_remove_link_mode(phydev,
+					     ETHTOOL_LINK_MODE_1000baseT_Full_BIT);
+	}
+	return ret;
 }
 EXPORT_SYMBOL(ksz9477_switch_register);
 

drivers/net/dsa/microchip/ksz_common.c

@@ -358,8 +358,6 @@ int ksz_enable_port(struct dsa_switch *ds, int port, struct phy_device *phy)
 
 	/* setup slave port */
 	dev->dev_ops->port_setup(dev, port, false);
-	if (dev->dev_ops->phy_setup)
-		dev->dev_ops->phy_setup(dev, port, phy);
 
 	/* port_stp_state_set() will be called after to enable the port so
 	 * there is no need to do anything.

drivers/net/dsa/microchip/ksz_common.h

@@ -119,8 +119,6 @@ struct ksz_dev_ops {
 	u32 (*get_port_addr)(int port, int offset);
 	void (*cfg_port_member)(struct ksz_device *dev, int port, u8 member);
 	void (*flush_dyn_mac_table)(struct ksz_device *dev, int port);
-	void (*phy_setup)(struct ksz_device *dev, int port,
-			  struct phy_device *phy);
 	void (*port_cleanup)(struct ksz_device *dev, int port);
 	void (*port_setup)(struct ksz_device *dev, int port, bool cpu_port);
 	void (*r_phy)(struct ksz_device *dev, u16 phy, u16 reg, u16 *val);