Merge tag 'hwmon-for-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon updates from Guenter Roeck:

 - Add support for Texas Instruments TMP512/513

 - Add support for LTC2947

 - Add support for BEL PFE1100 and PFE3000

 - Various minor improvements and fixes

* tag 'hwmon-for-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  dell-smm-hwmon: Add documentation
  hwmon: (dell-smm) Add support for disabling automatic BIOS fan control
  hwmon: Add driver for Texas Instruments TMP512/513 sensor chips.
  dt-bindings: hwmon: Add TMP512/513
  docs: hwmon: Document bel-pfe pmbus driver
  hwmon: (pmbus) add driver for BEL PFE1100 and PFE3000
  dt-bindings: hwmon: Add ltc2947 documentation
  hwmon: Add support for ltc2947
  hwmon: (ina3221) Add summation feature support
  hwmon: (tmp421) Allow reading at 2Hz instead of 0.5Hz
  hwmon: (w83793d) remove redundant assignment to variable res
  hwmon: (pmbus/ibm-cffps) Add version detection capability
  dt-bindings: hwmon: Document ibm,cffps compatible string
  hwmon: abituguru: make array probe_order static, makes object smaller
  hwmon: (applesmc) switch to using input device polling mode
  hwmon: (aspeed-pwm-tacho) Use devm_platform_ioremap_resource() in aspeed_pwm_tacho_probe()
  hwmon: (pmbus/ibm-cffps) Fix LED blink behavior
  hwmon: (pmbus/ibm-cffps) Switch LEDs to blocking brightness call

Documentation/devicetree/bindings/hwmon/adi,ltc2947.yaml

+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/bindings/hwmon/adi,ltc2947.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Analog Devices LTC2947 high precision power and energy monitor
+
+maintainers:
+  - Nuno Sá <nuno.sa@analog.com>
+
+description: |
+  Analog Devices LTC2947 high precision power and energy monitor over SPI or I2C.
+
+  https://www.analog.com/media/en/technical-documentation/data-sheets/LTC2947.pdf
+
+properties:
+  compatible:
+    enum:
+      - adi,ltc2947
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    description:
+      The LTC2947 uses either a trimmed internal oscillator or an external clock
+      as the time base for determining the integration period to represent time,
+      charge and energy. When an external clock is used, this property must be
+      set accordingly.
+    maxItems: 1
+
+  adi,accumulator-ctl-pol:
+    description:
+      This property controls the polarity of current that is accumulated to
+      calculate charge and energy so that, they can be only accumulated for
+      positive current for example. Since there are two sets of registers for
+      the accumulated values, this entry can also have two items which sets
+      energy1/charge1 and energy2/charger2 respectively. Check table 12 of the
+      datasheet for more information on the supported options.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32-array
+      - minItems: 2
+        maxItems: 2
+        items:
+          enum: [0, 1, 2, 3]
+          default: 0
+
+  adi,accumulation-deadband-microamp:
+    description:
+      This property controls the Accumulation Dead band which allows to set the
+      level of current below which no accumulation takes place.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+    maximum: 255
+    default: 0
+
+  adi,gpio-out-pol:
+    description:
+      This property controls the GPIO polarity. Setting it to one makes the GPIO
+      active high, setting it to zero makets it active low. When this property
+      is present, the GPIO is automatically configured as output and set to
+      control a fan as a function of measured temperature.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [0, 1]
+    default: 0
+
+  adi,gpio-in-accum:
+    description:
+      When set, this property sets the GPIO as input. It is then used to control
+      the accumulation of charge, energy and time. This function can be
+      enabled/configured separately for each of the two sets of accumulation
+      registers. Check table 13 of the datasheet for more information on the
+      supported options. This property cannot be used together with
+      adi,gpio-out-pol.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32-array
+      - minItems: 2
+        maxItems: 2
+        items:
+          enum: [0, 1, 2]
+          default: 0
+
+required:
+  - compatible
+  - reg
+
+
+examples:
+  - |
+    spi {
+           #address-cells = <1>;
+           #size-cells = <0>;
+
+           ltc2947_spi: ltc2947@0 {
+                   compatible = "adi,ltc2947";
+                   reg = <0>;
+                   /* accumulation takes place always for energ1/charge1. */
+                   /* accumulation only on positive current for energy2/charge2. */
+                   adi,accumulator-ctl-pol = <0 1>;
+           };
+    };
+...

Documentation/devicetree/bindings/hwmon/ibm,cffps1.txt

@@ -5,6 +5,9 @@ Required properties:
  - compatible				: Must be one of the following:
 						"ibm,cffps1"
 						"ibm,cffps2"
+						or "ibm,cffps" if the system
+						must support any version of the
+						power supply
  - reg = < I2C bus address >;		: Address of the power supply on the
 					  I2C bus.
 

Documentation/devicetree/bindings/hwmon/ti,tmp513.yaml

+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+
+$id: http://devicetree.org/schemas/hwmon/ti,tmp513.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: TMP513/512 system monitor sensor
+
+maintainers:
+  - Eric Tremblay <etremblay@distech-controls.com>
+
+description: |
+  The TMP512 (dual-channel) and TMP513 (triple-channel) are system monitors
+  that include remote sensors, a local temperature sensor, and a high-side
+  current shunt monitor. These system monitors have the capability of measuring
+  remote temperatures, on-chip temperatures, and system voltage/power/current
+  consumption.
+
+  Datasheets:
+  http://www.ti.com/lit/gpn/tmp513
+  http://www.ti.com/lit/gpn/tmp512
+
+
+properties:
+  compatible:
+    enum:
+      - ti,tmp512
+      - ti,tmp513
+
+  reg:
+    maxItems: 1
+
+  shunt-resistor-micro-ohms:
+    description: |
+      If 0, the calibration process will be skiped and the current and power
+      measurement engine will not work. Temperature and voltage measurement
+      will continue to work. The shunt value also need to respect:
+      rshunt <= pga-gain * 40 * 1000 * 1000.
+      If not, it's not possible to compute a valid calibration value.
+    default: 1000
+
+  ti,pga-gain:
+    description: |
+      The gain value for the PGA function. This is 8, 4, 2 or 1.
+      The PGA gain affect the shunt voltage range.
+      The range will be equal to: pga-gain * 40mV
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [1, 2, 4, 8]
+    default: 8
+
+  ti,bus-range-microvolt:
+    description: |
+      This is the operating range of the bus voltage in microvolt
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [16000000, 32000000]
+    default: 32000000
+
+  ti,nfactor:
+    description: |
+      Array of three(TMP513) or two(TMP512) n-Factor value for each remote
+      temperature channel.
+      See datasheet Table 11 for n-Factor range list and value interpretation.
+    allOf:
+      - $ref: /schemas/types.yaml#definitions/uint32-array
+      - minItems: 2
+        maxItems: 3
+        items:
+          default: 0x00
+          minimum: 0x00
+          maximum: 0xFF
+
+required:
+  - compatible
+  - reg
+
+examples:
+  - |
+    i2c {
+          #address-cells = <1>;
+          #size-cells = <0>;
+
+          tmp513@5c {
+              compatible = "ti,tmp513";
+              reg = <0x5C>;
+              shunt-resistor-micro-ohms = <330000>;
+              ti,bus-range-microvolt = <32000000>;
+              ti,pga-gain = <8>;
+              ti,nfactor = <0x1 0xF3 0x00>;
+          };
+    };

Documentation/hwmon/bel-pfe.rst

+Kernel driver bel-pfe
+======================
+
+Supported chips:
+
+  * BEL PFE1100
+
+    Prefixes: 'pfe1100'
+
+    Addresses scanned: -
+
+    Datasheet: https://www.belfuse.com/resources/datasheets/powersolutions/ds-bps-pfe1100-12-054xa.pdf
+
+  * BEL PFE3000
+
+    Prefixes: 'pfe3000'
+
+    Addresses scanned: -
+
+    Datasheet: https://www.belfuse.com/resources/datasheets/powersolutions/ds-bps-pfe3000-series.pdf
+
+Author: Tao Ren <rentao.bupt@gmail.com>
+
+
+Description
+-----------
+
+This driver supports hardware monitoring for below power supply devices
+which support PMBus Protocol:
+
+  * BEL PFE1100
+
+    1100 Watt AC to DC power-factor-corrected (PFC) power supply.
+    PMBus Communication Manual is not publicly available.
+
+  * BEL PFE3000
+
+    3000 Watt AC/DC power-factor-corrected (PFC) and DC-DC power supply.
+    PMBus Communication Manual is not publicly available.
+
+The driver is a client driver to the core PMBus driver. Please see
+Documentation/hwmon/pmbus.rst for details on PMBus client drivers.
+
+
+Usage Notes
+-----------
+
+This driver does not auto-detect devices. You will have to instantiate the
+devices explicitly. Please see Documentation/i2c/instantiating-devices.rst for
+details.
+
+Example: the following will load the driver for an PFE3000 at address 0x20
+on I2C bus #1::
+
+	$ modprobe bel-pfe
+	$ echo pfe3000 0x20 > /sys/bus/i2c/devices/i2c-1/new_device
+
+
+Platform data support
+---------------------
+
+The driver supports standard PMBus driver platform data.
+
+
+Sysfs entries
+-------------
+
+======================= =======================================================
+curr1_label		"iin"
+curr1_input		Measured input current
+curr1_max               Input current max value
+curr1_max_alarm         Input current max alarm
+
+curr[2-3]_label		"iout[1-2]"
+curr[2-3]_input		Measured output current
+curr[2-3]_max           Output current max value
+curr[2-3]_max_alarm     Output current max alarm
+
+fan[1-2]_input          Fan 1 and 2 speed in RPM
+fan1_target             Set fan speed reference for both fans
+
+in1_label		"vin"
+in1_input		Measured input voltage
+in1_crit		Input voltage critical max value
+in1_crit_alarm		Input voltage critical max alarm
+in1_lcrit               Input voltage critical min value
+in1_lcrit_alarm         Input voltage critical min alarm
+in1_max                 Input voltage max value
+in1_max_alarm           Input voltage max alarm
+
+in2_label               "vcap"
+in2_input               Hold up capacitor voltage
+
+in[3-8]_label		"vout[1-3,5-7]"
+in[3-8]_input		Measured output voltage
+in[3-4]_alarm           vout[1-2] output voltage alarm
+
+power[1-2]_label	"pin[1-2]"
+power[1-2]_input        Measured input power
+power[1-2]_alarm	Input power high alarm
+
+power[3-4]_label	"pout[1-2]"
+power[3-4]_input	Measured output power
+
+temp[1-3]_input		Measured temperature
+temp[1-3]_alarm         Temperature alarm
+======================= =======================================================
+
+.. note::
+
+    - curr3, fan2, vout[2-7], vcap, pin2, pout2 and temp3 attributes only
+      exist for PFE3000.

Documentation/hwmon/dell-smm-hwmon.rst

+.. SPDX-License-Identifier: GPL-2.0-or-later
+
+.. include:: <isonum.txt>
+
+Kernel driver dell-smm-hwmon
+============================
+
+:Copyright: |copy| 2002-2005 Massimo Dal Zotto <dz@debian.org>
+:Copyright: |copy| 2019 Giovanni Mascellani <gio@debian.org>
+
+Description
+-----------
+
+On many Dell laptops the System Management Mode (SMM) BIOS can be
+queried for the status of fans and temperature sensors.  Userspace
+utilities like ``sensors`` can be used to return the readings. The
+userspace suite `i8kutils`__ can also be used to read the sensors and
+automatically adjust fan speed (please notice that it currently uses
+the deprecated ``/proc/i8k`` interface).
+
+ __ https://github.com/vitorafsr/i8kutils
+
+``sysfs`` interface
+-------------------
+
+Temperature sensors and fans can be queried and set via the standard
+``hwmon`` interface on ``sysfs``, under the directory
+``/sys/class/hwmon/hwmonX`` for some value of ``X`` (search for the
+``X`` such that ``/sys/class/hwmon/hwmonX/name`` has content
+``dell_smm``). A number of other attributes can be read or written:
+
+=============================== ======= =======================================
+Name				Perm	Description
+=============================== ======= =======================================
+fan[1-3]_input                  RO      Fan speed in RPM.
+fan[1-3]_label                  RO      Fan label.
+pwm[1-3]                        RW      Control the fan PWM duty-cycle.
+pwm1_enable                     WO      Enable or disable automatic BIOS fan
+                                        control (not supported on all laptops,
+                                        see below for details).
+temp[1-10]_input                RO      Temperature reading in milli-degrees
+                                        Celsius.
+temp[1-10]_label                RO      Temperature sensor label.
+=============================== ======= =======================================
+
+Disabling automatic BIOS fan control
+------------------------------------
+
+On some laptops the BIOS automatically sets fan speed every few
+seconds. Therefore the fan speed set by mean of this driver is quickly
+overwritten.
+
+There is experimental support for disabling automatic BIOS fan
+control, at least on laptops where the corresponding SMM command is
+known, by writing the value ``1`` in the attribute ``pwm1_enable``
+(writing ``2`` enables automatic BIOS control again). Even if you have
+more than one fan, all of them are set to either enabled or disabled
+automatic fan control at the same time and, notwithstanding the name,
+``pwm1_enable`` sets automatic control for all fans.
+
+If ``pwm1_enable`` is not available, then it means that SMM codes for
+enabling and disabling automatic BIOS fan control are not whitelisted
+for your hardware. It is possible that codes that work for other
+laptops actually work for yours as well, or that you have to discover
+new codes.
+
+Check the list ``i8k_whitelist_fan_control`` in file
+``drivers/hwmon/dell-smm-hwmon.c`` in the kernel tree: as a first
+attempt you can try to add your machine and use an already-known code
+pair. If, after recompiling the kernel, you see that ``pwm1_enable``
+is present and works (i.e., you can manually control the fan speed),
+then please submit your finding as a kernel patch, so that other users
+can benefit from it. Please see
+:ref:`Documentation/process/submitting-patches.rst <submittingpatches>`
+for information on submitting patches.
+
+If no known code works on your machine, you need to resort to do some
+probing, because unfortunately Dell does not publish datasheets for
+its SMM. You can experiment with the code in `this repository`__ to
+probe the BIOS on your machine and discover the appropriate codes.
+
+ __ https://github.com/clopez/dellfan/
+
+Again, when you find new codes, we'd be happy to have your patches!
+
+Module parameters
+-----------------
+
+* force:bool
+                   Force loading without checking for supported
+                   models. (default: 0)
+
+* ignore_dmi:bool
+                   Continue probing hardware even if DMI data does not
+                   match. (default: 0)
+
+* restricted:bool
+                   Allow fan control only to processes with the
+                   ``CAP_SYS_ADMIN`` capability set or processes run
+                   as root when using the legacy ``/proc/i8k``
+                   interface. In this case normal users will be able
+                   to read temperature and fan status but not to
+                   control the fan.  If your notebook is shared with
+                   other users and you don't trust them you may want
+                   to use this option. (default: 1, only available
+                   with ``CONFIG_I8K``)
+
+* power_status:bool
+                   Report AC status in ``/proc/i8k``. (default: 0,
+                   only available with ``CONFIG_I8K``)
+
+* fan_mult:uint
+                   Factor to multiply fan speed with. (default:
+                   autodetect)
+
+* fan_max:uint
+                   Maximum configurable fan speed. (default:
+                   autodetect)
+
+Legacy ``/proc`` interface
+--------------------------
+
+.. warning:: This interface is obsolete and deprecated and should not
+             used in new applications. This interface is only
+             available when kernel is compiled with option
+             ``CONFIG_I8K``.
+
+The information provided by the kernel driver can be accessed by
+simply reading the ``/proc/i8k`` file. For example::
+
+    $ cat /proc/i8k
+    1.0 A17 2J59L02 52 2 1 8040 6420 1 2
+
+The fields read from ``/proc/i8k`` are::
+
+    1.0 A17 2J59L02 52 2 1 8040 6420 1 2
+    |   |   |       |  | | |    |    | |
+    |   |   |       |  | | |    |    | +------- 10. buttons status
+    |   |   |       |  | | |    |    +--------- 9.  AC status
+    |   |   |       |  | | |    +-------------- 8.  fan0 RPM
+    |   |   |       |  | | +------------------- 7.  fan1 RPM
+    |   |   |       |  | +--------------------- 6.  fan0 status
+    |   |   |       |  +----------------------- 5.  fan1 status
+    |   |   |       +-------------------------- 4.  temp0 reading (Celsius)
+    |   |   +---------------------------------- 3.  Dell service tag (later known as 'serial number')
+    |   +-------------------------------------- 2.  BIOS version
+    +------------------------------------------ 1.  /proc/i8k format version
+
+A negative value, for example -22, indicates that the BIOS doesn't
+return the corresponding information. This is normal on some
+models/BIOSes.
+
+For performance reasons the ``/proc/i8k`` doesn't report by default
+the AC status since this SMM call takes a long time to execute and is
+not really needed.  If you want to see the ac status in ``/proc/i8k``
+you must explictitly enable this option by passing the
+``power_status=1`` parameter to insmod. If AC status is not
+available -1 is printed instead.
+
+The driver provides also an ioctl interface which can be used to
+obtain the same information and to control the fan status. The ioctl
+interface can be accessed from C programs or from shell using the
+i8kctl utility. See the source file of ``i8kutils`` for more
+information on how to use the ioctl interface.

Documentation/hwmon/ina3221.rst

@@ -41,6 +41,18 @@ curr[123]_max           Warning alert current(mA) setting, activates the
 			average is above this value.
 curr[123]_max_alarm     Warning alert current limit exceeded
 in[456]_input           Shunt voltage(uV) for channels 1, 2, and 3 respectively
+in7_input               Sum of shunt voltage(uV) channels
+in7_label               Channel label for sum of shunt voltage
+curr4_input             Sum of current(mA) measurement channels,
+                        (only available when all channels use the same resistor
+                        value for their shunt resistors)
+curr4_crit              Critical alert current(mA) setting for sum of current
+                        measurements, activates the corresponding alarm
+                        when the respective current is above this value
+                        (only effective when all channels use the same resistor
+                        value for their shunt resistors)
+curr4_crit_alarm        Critical alert current limit exceeded for sum of
+                        current measurements.
 samples                 Number of samples using in the averaging mode.
 
                         Supports the list of number of samples:

Documentation/hwmon/index.rst

@@ -41,9 +41,11 @@ Hardware Monitoring Kernel Drivers
    asb100
    asc7621
    aspeed-pwm-tacho
+   bel-pfe
    coretemp
    da9052
    da9055
+   dell-smm-hwmon
    dme1737
    ds1621
    ds620
@@ -90,6 +92,7 @@ Hardware Monitoring Kernel Drivers
    lm95245
    lochnagar
    ltc2945
+   ltc2947
    ltc2978
    ltc2990
    ltc3815
@@ -153,6 +156,7 @@ Hardware Monitoring Kernel Drivers
    tmp108
    tmp401
    tmp421
+   tmp513
    tps40422
    twl4030-madc-hwmon
    ucd9000

Documentation/hwmon/ltc2947.rst

+Kernel drivers ltc2947-i2c and ltc2947-spi
+==========================================
+
+Supported chips:
+
+  * Analog Devices LTC2947
+
+    Prefix: 'ltc2947'
+
+    Addresses scanned: -
+
+    Datasheet:
+
+        https://www.analog.com/media/en/technical-documentation/data-sheets/LTC2947.pdf
+
+Author: Nuno Sá <nuno.sa@analog.com>
+
+Description
+___________
+
+The LTC2947 is a high precision power and energy monitor that measures current,
+voltage, power, temperature, charge and energy. The device supports both SPI
+and I2C depending on the chip configuration.
+The device also measures accumulated quantities as energy. It has two banks of
+register's to read/set energy related values. These banks can be configured
+independently to have setups like: energy1 accumulates always and enrgy2 only
+accumulates if current is positive (to check battery charging efficiency for
+example). The device also supports a GPIO pin that can be configured as output
+to control a fan as a function of measured temperature. Then, the GPIO becomes
+active as soon as a temperature reading is higher than a defined threshold. The
+temp2 channel is used to control this thresholds and to read the respective
+alarms.
+
+Sysfs entries
+_____________
+
+The following attributes are supported. Limits are read-write, reset_history
+is write-only and all the other attributes are read-only.
+
+======================= ==========================================
+in0_input		VP-VM voltage (mV).
+in0_min			Undervoltage threshold
+in0_max			Overvoltage threshold
+in0_lowest		Lowest measured voltage
+in0_highest		Highest measured voltage
+in0_reset_history	Write 1 to reset in1 history
+in0_min_alarm		Undervoltage alarm
+in0_max_alarm		Overvoltage alarm
+in0_label		Channel label (VP-VM)
+
+in1_input		DVCC voltage (mV)
+in1_min			Undervoltage threshold
+in1_max			Overvoltage threshold
+in1_lowest		Lowest measured voltage
+in1_highest		Highest measured voltage
+in1_reset_history	Write 1 to reset in2 history
+in1_min_alarm		Undervoltage alarm
+in1_max_alarm		Overvoltage alarm
+in1_label		Channel label (DVCC)
+
+curr1_input		IP-IM Sense current (mA)
+curr1_min		Undercurrent threshold
+curr1_max		Overcurrent threshold
+curr1_lowest		Lowest measured current
+curr1_highest		Highest measured current
+curr1_reset_history	Write 1 to reset curr1 history
+curr1_min_alarm		Undercurrent alarm
+curr1_max_alarm		Overcurrent alarm
+curr1_label		Channel label (IP-IM)
+
+power1_input		Power (in uW)
+power1_min		Low power threshold
+power1_max		High power threshold
+power1_input_lowest	Historical minimum power use
+power1_input_highest	Historical maximum power use
+power1_reset_history	Write 1 to reset power1 history
+power1_min_alarm	Low power alarm
+power1_max_alarm	High power alarm
+power1_label		Channel label (Power)
+
+temp1_input		Chip Temperature (in milliC)
+temp1_min		Low temperature threshold
+temp1_max		High temperature threshold
+temp1_input_lowest	Historical minimum temperature use
+temp1_input_highest	Historical maximum temperature use
+temp1_reset_history	Write 1 to reset temp1 history
+temp1_min_alarm		Low temperature alarm
+temp1_max_alarm		High temperature alarm
+temp1_label		Channel label (Ambient)
+
+temp2_min		Low temperature threshold for fan control
+temp2_max		High temperature threshold for fan control
+temp2_min_alarm		Low temperature fan control alarm
+temp2_max_alarm		High temperature fan control alarm
+temp2_label		Channel label (TEMPFAN)
+
+energy1_input		Measured energy over time (in microJoule)
+
+energy2_input		Measured energy over time (in microJoule)
+======================= ==========================================

Documentation/hwmon/tmp513.rst

+.. SPDX-License-Identifier: GPL-2.0
+
+Kernel driver tmp513
+====================
+
+Supported chips:
+
+  * Texas Instruments TMP512
+
+    Prefix: 'tmp512'
+
+    Datasheet: http://www.ti.com/lit/ds/symlink/tmp512.pdf
+
+  * Texas Instruments TMP513
+
+    Prefix: 'tmp513'
+
+    Datasheet: http://www.ti.com/lit/ds/symlink/tmp513.pdf
+
+Authors:
+
+	Eric Tremblay <etremblay@distech-controls.com>
+
+Description
+-----------
+
+This driver implements support for Texas Instruments TMP512, and TMP513.
+The TMP512 (dual-channel) and TMP513 (triple-channel) are system monitors
+that include remote sensors, a local temperature sensor, and a high-side current
+shunt monitor. These system monitors have the capability of measuring remote
+temperatures, on-chip temperatures, and system voltage/power/current
+consumption.
+
+The temperatures are measured in degrees Celsius with a range of
+-40 to + 125 degrees with a resolution of 0.0625 degree C.
+
+For hysteresis value, only the first channel is writable. Writing to it
+will affect all other values since each channels are sharing the same
+hysteresis value. The hysteresis is in degrees Celsius with a range of
+0 to 127.5 degrees with a resolution of 0.5 degree.
+
+The driver exports the temperature values via the following sysfs files:
+
+**temp[1-4]_input**
+
+**temp[1-4]_crit**
+
+**temp[1-4]_crit_alarm**
+
+**temp[1-4]_crit_hyst**
+
+The driver read the shunt voltage from the chip and convert it to current.
+The readable range depends on the "ti,pga-gain" property (default to 8) and the
+shunt resistor value. The value resolution will be equal to 10uV/Rshunt.
+
+The driver exports the shunt currents values via the following sysFs files:
+
+**curr1_input**
+
+**curr1_lcrit**
+
+**curr1_lcrit_alarm**
+
+**curr1_crit**
+
+**curr1_crit_alarm**
+
+The bus voltage range is read from the chip with a resolution of 4mV. The chip
+can be configurable in two different range (32V or 16V) using the
+ti,bus-range-microvolt property in the devicetree.
+
+The driver exports the bus voltage values via the following sysFs files:
+
+**in0_input**
+
+**in0_lcrit**
+
+**in0_lcrit_alarm**
+
+**in0_crit**
+
+**in0_crit_alarm**
+
+The bus power and bus currents range and resolution depends on the calibration
+register value. Those values are calculate by the hardware using those
+formulas:
+
+Current = (ShuntVoltage * CalibrationRegister) / 4096
+Power   = (Current * BusVoltage) / 5000
+
+The driver exports the bus current and bus power values via the following
+sysFs files:
+
+**curr2_input**
+
+**power1_input**
+
+**power1_crit**
+
+**power1_crit_alarm**
+
+The calibration process follow the procedure of the datasheet (without overflow)
+and depend on the shunt resistor value and the pga_gain value.

MAINTAINERS

@@ -9717,6 +9717,17 @@ S:	Maintained
 F:	Documentation/hwmon/ltc4261.rst
 F:	drivers/hwmon/ltc4261.c
 
+LTC2947 HARDWARE MONITOR DRIVER
+M:	Nuno Sá <nuno.sa@analog.com>
+W:	http://ez.analog.com/community/linux-device-drivers
+L:	linux-hwmon@vger.kernel.org
+S:	Supported
+F:	drivers/hwmon/ltc2947-core.c
+F:	drivers/hwmon/ltc2947-spi.c
+F:	drivers/hwmon/ltc2947-i2c.c
+F:	drivers/hwmon/ltc2947.h
+F:	Documentation/devicetree/bindings/hwmon/adi,ltc2947.yaml
+
 LTC4306 I2C MULTIPLEXER DRIVER
 M:	Michael Hennerich <michael.hennerich@analog.com>
 W:	http://ez.analog.com/community/linux-device-drivers
@@ -16493,6 +16504,13 @@ S:	Maintained
 F:	Documentation/hwmon/tmp401.rst
 F:	drivers/hwmon/tmp401.c
 
+TMP513 HARDWARE MONITOR DRIVER
+M:	Eric Tremblay <etremblay@distech-controls.com>
+L:	linux-hwmon@vger.kernel.org
+S:	Maintained
+F:	Documentation/hwmon/tmp513.rst
+F:	drivers/hwmon/tmp513.c
+
 TMPFS (SHMEM FILESYSTEM)
 M:	Hugh Dickins <hughd@google.com>
 L:	linux-mm@kvack.org

drivers/hwmon/Kconfig

@@ -310,7 +310,6 @@ config SENSORS_APPLESMC
 	depends on INPUT && X86
 	select NEW_LEDS
 	select LEDS_CLASS
-	select INPUT_POLLDEV
 	help
 	  This driver provides support for the Apple System Management
 	  Controller, which provides an accelerometer (Apple Sudden Motion
@@ -728,6 +727,33 @@ config SENSORS_LTC2945
 	  This driver can also be built as a module. If so, the module will
 	  be called ltc2945.
 
+config SENSORS_LTC2947
+	tristate
+
+config SENSORS_LTC2947_I2C
+	tristate "Analog Devices LTC2947 High Precision Power and Energy Monitor over I2C"
+	depends on I2C
+	select REGMAP_I2C
+	select SENSORS_LTC2947
+	help
+	  If you say yes here you get support for Linear Technology LTC2947
+	  I2C High Precision Power and Energy Monitor
+
+	  This driver can also be built as a module. If so, the module will
+	  be called ltc2947-i2c.
+
+config SENSORS_LTC2947_SPI
+	tristate "Analog Devices LTC2947 High Precision Power and Energy Monitor over SPI"
+	depends on SPI_MASTER
+	select REGMAP_SPI
+	select SENSORS_LTC2947
+	help
+	  If you say yes here you get support for Linear Technology LTC2947
+	  SPI High Precision Power and Energy Monitor
+
+	  This driver can also be built as a module. If so, the module will
+	  be called ltc2947-spi.
+
 config SENSORS_LTC2990
 	tristate "Linear Technology LTC2990"
 	depends on I2C
@@ -1710,6 +1736,16 @@ config SENSORS_TMP421
 	  This driver can also be built as a module. If so, the module
 	  will be called tmp421.
 
+config SENSORS_TMP513
+	tristate "Texas Instruments TMP513 and compatibles"
+	depends on I2C
+	help
+	  If you say yes here you get support for Texas Instruments TMP512,
+	  and TMP513 temperature and power supply sensor chips.
+
+	  This driver can also be built as a module. If so, the module
+	  will be called tmp513.
+
 config SENSORS_VEXPRESS
 	tristate "Versatile Express"
 	depends on VEXPRESS_CONFIG

drivers/hwmon/Makefile

@@ -106,6 +106,9 @@ obj-$(CONFIG_SENSORS_LM95234)	+= lm95234.o
 obj-$(CONFIG_SENSORS_LM95241)	+= lm95241.o
 obj-$(CONFIG_SENSORS_LM95245)	+= lm95245.o
 obj-$(CONFIG_SENSORS_LTC2945)	+= ltc2945.o
+obj-$(CONFIG_SENSORS_LTC2947)	+= ltc2947-core.o
+obj-$(CONFIG_SENSORS_LTC2947_I2C) += ltc2947-i2c.o
+obj-$(CONFIG_SENSORS_LTC2947_SPI) += ltc2947-spi.o
 obj-$(CONFIG_SENSORS_LTC2990)	+= ltc2990.o
 obj-$(CONFIG_SENSORS_LTC4151)	+= ltc4151.o
 obj-$(CONFIG_SENSORS_LTC4215)	+= ltc4215.o
@@ -166,6 +169,7 @@ obj-$(CONFIG_SENSORS_TMP103)	+= tmp103.o
 obj-$(CONFIG_SENSORS_TMP108)	+= tmp108.o
 obj-$(CONFIG_SENSORS_TMP401)	+= tmp401.o
 obj-$(CONFIG_SENSORS_TMP421)	+= tmp421.o
+obj-$(CONFIG_SENSORS_TMP513)	+= tmp513.o
 obj-$(CONFIG_SENSORS_VEXPRESS)	+= vexpress-hwmon.o
 obj-$(CONFIG_SENSORS_VIA_CPUTEMP)+= via-cputemp.o
 obj-$(CONFIG_SENSORS_VIA686A)	+= via686a.o

drivers/hwmon/abituguru.c

@@ -1264,7 +1264,7 @@ static int abituguru_probe(struct platform_device *pdev)
 	 * El weirdo probe order, to keep the sysfs order identical to the
 	 * BIOS and window-appliction listing order.
 	 */
-	const u8 probe_order[ABIT_UGURU_MAX_BANK1_SENSORS] = {
+	static const u8 probe_order[ABIT_UGURU_MAX_BANK1_SENSORS] = {
 		0x00, 0x01, 0x03, 0x04, 0x0A, 0x08, 0x0E, 0x02,
 		0x09, 0x06, 0x05, 0x0B, 0x0F, 0x0D, 0x07, 0x0C };
 

drivers/hwmon/applesmc.c

@@ -19,7 +19,7 @@
 
 #include <linux/delay.h>
 #include <linux/platform_device.h>
-#include <linux/input-polldev.h>
+#include <linux/input.h>
 #include <linux/kernel.h>
 #include <linux/slab.h>
 #include <linux/module.h>
@@ -140,7 +140,7 @@ static s16 rest_y;
 static u8 backlight_state[2];
 
 static struct device *hwmon_dev;
-static struct input_polled_dev *applesmc_idev;
+static struct input_dev *applesmc_idev;
 
 /*
  * Last index written to key_at_index sysfs file, and value to use for all other
@@ -681,9 +681,8 @@ static void applesmc_calibrate(void)
 	rest_x = -rest_x;
 }
 
-static void applesmc_idev_poll(struct input_polled_dev *dev)
+static void applesmc_idev_poll(struct input_dev *idev)
 {
-	struct input_dev *idev = dev->input;
 	s16 x, y;
 
 	if (applesmc_read_s16(MOTION_SENSOR_X_KEY, &x))
@@ -1134,7 +1133,6 @@ static int applesmc_create_nodes(struct applesmc_node_group *groups, int num)
 /* Create accelerometer resources */
 static int applesmc_create_accelerometer(void)
 {
-	struct input_dev *idev;
 	int ret;
 
 	if (!smcreg.has_accelerometer)
@@ -1144,37 +1142,38 @@ static int applesmc_create_accelerometer(void)
 	if (ret)
 		goto out;
 
-	applesmc_idev = input_allocate_polled_device();
+	applesmc_idev = input_allocate_device();
 	if (!applesmc_idev) {
 		ret = -ENOMEM;
 		goto out_sysfs;
 	}
 
-	applesmc_idev->poll = applesmc_idev_poll;
-	applesmc_idev->poll_interval = APPLESMC_POLL_INTERVAL;
-
 	/* initial calibrate for the input device */
 	applesmc_calibrate();
 
 	/* initialize the input device */
-	idev = applesmc_idev->input;
-	idev->name = "applesmc";
-	idev->id.bustype = BUS_HOST;
-	idev->dev.parent = &pdev->dev;
-	idev->evbit[0] = BIT_MASK(EV_ABS);
-	input_set_abs_params(idev, ABS_X,
+	applesmc_idev->name = "applesmc";
+	applesmc_idev->id.bustype = BUS_HOST;
+	applesmc_idev->dev.parent = &pdev->dev;
+	input_set_abs_params(applesmc_idev, ABS_X,
 			-256, 256, APPLESMC_INPUT_FUZZ, APPLESMC_INPUT_FLAT);
-	input_set_abs_params(idev, ABS_Y,
+	input_set_abs_params(applesmc_idev, ABS_Y,
 			-256, 256, APPLESMC_INPUT_FUZZ, APPLESMC_INPUT_FLAT);
 
-	ret = input_register_polled_device(applesmc_idev);
+	ret = input_setup_polling(applesmc_idev, applesmc_idev_poll);
+	if (ret)
+		goto out_idev;
+
+	input_set_poll_interval(applesmc_idev, APPLESMC_POLL_INTERVAL);
+
+	ret = input_register_device(applesmc_idev);
 	if (ret)
 		goto out_idev;
 
 	return 0;
 
 out_idev:
-	input_free_polled_device(applesmc_idev);
+	input_free_device(applesmc_idev);
 
 out_sysfs:
 	applesmc_destroy_nodes(accelerometer_group);
@@ -1189,8 +1188,7 @@ static void applesmc_release_accelerometer(void)
 {
 	if (!smcreg.has_accelerometer)
 		return;
-	input_unregister_polled_device(applesmc_idev);
-	input_free_polled_device(applesmc_idev);
+	input_unregister_device(applesmc_idev);
 	applesmc_destroy_nodes(accelerometer_group);
 }
 

drivers/hwmon/aspeed-pwm-tacho.c

@@ -891,17 +891,12 @@ static int aspeed_pwm_tacho_probe(struct platform_device *pdev)
 	struct device_node *np, *child;
 	struct aspeed_pwm_tacho_data *priv;
 	void __iomem *regs;
-	struct resource *res;
 	struct device *hwmon;
 	struct clk *clk;
 	int ret;
 
 	np = dev->of_node;
-
-	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	if (!res)
-		return -ENOENT;
-	regs = devm_ioremap_resource(dev, res);
+	regs = devm_platform_ioremap_resource(pdev, 0);
 	if (IS_ERR(regs))
 		return PTR_ERR(regs);
 	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);

drivers/hwmon/dell-smm-hwmon.c

@@ -68,6 +68,8 @@ static uint i8k_pwm_mult;
 static uint i8k_fan_max = I8K_FAN_HIGH;
 static bool disallow_fan_type_call;
 static bool disallow_fan_support;
+static unsigned int manual_fan;
+static unsigned int auto_fan;
 
 #define I8K_HWMON_HAVE_TEMP1	(1 << 0)
 #define I8K_HWMON_HAVE_TEMP2	(1 << 1)
@@ -300,6 +302,20 @@ static int i8k_get_fan_nominal_speed(int fan, int speed)
 	return i8k_smm(&regs) ? : (regs.eax & 0xffff) * i8k_fan_mult;
 }
 
+/*
+ * Enable or disable automatic BIOS fan control support
+ */
+static int i8k_enable_fan_auto_mode(bool enable)
+{
+	struct smm_regs regs = { };
+
+	if (disallow_fan_support)
+		return -EINVAL;
+
+	regs.eax = enable ? auto_fan : manual_fan;
+	return i8k_smm(&regs);
+}
+
 /*
  * Set the fan speed (off, low, high). Returns the new fan status.
  */
@@ -726,6 +742,35 @@ static ssize_t i8k_hwmon_pwm_store(struct device *dev,
 	return err < 0 ? -EIO : count;
 }
 
+static ssize_t i8k_hwmon_pwm_enable_store(struct device *dev,
+					  struct device_attribute *attr,
+					  const char *buf, size_t count)
+{
+	int err;
+	bool enable;
+	unsigned long val;
+
+	if (!auto_fan)
+		return -ENODEV;
+
+	err = kstrtoul(buf, 10, &val);
+	if (err)
+		return err;
+
+	if (val == 1)
+		enable = false;
+	else if (val == 2)
+		enable = true;
+	else
+		return -EINVAL;
+
+	mutex_lock(&i8k_mutex);
+	err = i8k_enable_fan_auto_mode(enable);
+	mutex_unlock(&i8k_mutex);
+
+	return err ? err : count;
+}
+
 static SENSOR_DEVICE_ATTR_RO(temp1_input, i8k_hwmon_temp, 0);
 static SENSOR_DEVICE_ATTR_RO(temp1_label, i8k_hwmon_temp_label, 0);
 static SENSOR_DEVICE_ATTR_RO(temp2_input, i8k_hwmon_temp, 1);
@@ -749,6 +794,7 @@ static SENSOR_DEVICE_ATTR_RO(temp10_label, i8k_hwmon_temp_label, 9);
 static SENSOR_DEVICE_ATTR_RO(fan1_input, i8k_hwmon_fan, 0);
 static SENSOR_DEVICE_ATTR_RO(fan1_label, i8k_hwmon_fan_label, 0);
 static SENSOR_DEVICE_ATTR_RW(pwm1, i8k_hwmon_pwm, 0);
+static SENSOR_DEVICE_ATTR_WO(pwm1_enable, i8k_hwmon_pwm_enable, 0);
 static SENSOR_DEVICE_ATTR_RO(fan2_input, i8k_hwmon_fan, 1);
 static SENSOR_DEVICE_ATTR_RO(fan2_label, i8k_hwmon_fan_label, 1);
 static SENSOR_DEVICE_ATTR_RW(pwm2, i8k_hwmon_pwm, 1);
@@ -780,12 +826,13 @@ static struct attribute *i8k_attrs[] = {
 	&sensor_dev_attr_fan1_input.dev_attr.attr,	/* 20 */
 	&sensor_dev_attr_fan1_label.dev_attr.attr,	/* 21 */
 	&sensor_dev_attr_pwm1.dev_attr.attr,		/* 22 */
-	&sensor_dev_attr_fan2_input.dev_attr.attr,	/* 23 */
-	&sensor_dev_attr_fan2_label.dev_attr.attr,	/* 24 */
-	&sensor_dev_attr_pwm2.dev_attr.attr,		/* 25 */
-	&sensor_dev_attr_fan3_input.dev_attr.attr,	/* 26 */
-	&sensor_dev_attr_fan3_label.dev_attr.attr,	/* 27 */
-	&sensor_dev_attr_pwm3.dev_attr.attr,		/* 28 */
+	&sensor_dev_attr_pwm1_enable.dev_attr.attr,	/* 23 */
+	&sensor_dev_attr_fan2_input.dev_attr.attr,	/* 24 */
+	&sensor_dev_attr_fan2_label.dev_attr.attr,	/* 25 */
+	&sensor_dev_attr_pwm2.dev_attr.attr,		/* 26 */
+	&sensor_dev_attr_fan3_input.dev_attr.attr,	/* 27 */
+	&sensor_dev_attr_fan3_label.dev_attr.attr,	/* 28 */
+	&sensor_dev_attr_pwm3.dev_attr.attr,		/* 29 */
 	NULL
 };
 
@@ -828,16 +875,19 @@ static umode_t i8k_is_visible(struct kobject *kobj, struct attribute *attr,
 	    !(i8k_hwmon_flags & I8K_HWMON_HAVE_TEMP10))
 		return 0;
 
-	if (index >= 20 && index <= 22 &&
+	if (index >= 20 && index <= 23 &&
 	    !(i8k_hwmon_flags & I8K_HWMON_HAVE_FAN1))
 		return 0;
-	if (index >= 23 && index <= 25 &&
+	if (index >= 24 && index <= 26 &&
 	    !(i8k_hwmon_flags & I8K_HWMON_HAVE_FAN2))
 		return 0;
-	if (index >= 26 && index <= 28 &&
+	if (index >= 27 && index <= 29 &&
 	    !(i8k_hwmon_flags & I8K_HWMON_HAVE_FAN3))
 		return 0;
 
+	if (index == 23 && !auto_fan)
+		return 0;
+
 	return attr->mode;
 }
 
@@ -1135,12 +1185,48 @@ static struct dmi_system_id i8k_blacklist_fan_support_dmi_table[] __initdata = {
 	{ }
 };
 
+struct i8k_fan_control_data {
+	unsigned int manual_fan;
+	unsigned int auto_fan;
+};
+
+enum i8k_fan_controls {
+	I8K_FAN_34A3_35A3,
+};
+
+static const struct i8k_fan_control_data i8k_fan_control_data[] = {
+	[I8K_FAN_34A3_35A3] = {
+		.manual_fan = 0x34a3,
+		.auto_fan = 0x35a3,
+	},
+};
+
+static struct dmi_system_id i8k_whitelist_fan_control[] __initdata = {
+	{
+		.ident = "Dell Precision 5530",
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."),
+			DMI_EXACT_MATCH(DMI_PRODUCT_NAME, "Precision 5530"),
+		},
+		.driver_data = (void *)&i8k_fan_control_data[I8K_FAN_34A3_35A3],
+	},
+	{
+		.ident = "Dell Latitude E6440",
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."),
+			DMI_EXACT_MATCH(DMI_PRODUCT_NAME, "Latitude E6440"),
+		},
+		.driver_data = (void *)&i8k_fan_control_data[I8K_FAN_34A3_35A3],
+	},
+	{ }
+};
+
 /*
  * Probe for the presence of a supported laptop.
  */
 static int __init i8k_probe(void)
 {
-	const struct dmi_system_id *id;
+	const struct dmi_system_id *id, *fan_control;
 	int fan, ret;
 
 	/*
@@ -1200,6 +1286,15 @@ static int __init i8k_probe(void)
 	i8k_fan_max = fan_max ? : I8K_FAN_HIGH;	/* Must not be 0 */
 	i8k_pwm_mult = DIV_ROUND_UP(255, i8k_fan_max);
 
+	fan_control = dmi_first_match(i8k_whitelist_fan_control);
+	if (fan_control && fan_control->driver_data) {
+		const struct i8k_fan_control_data *data = fan_control->driver_data;
+
+		manual_fan = data->manual_fan;
+		auto_fan = data->auto_fan;
+		pr_info("enabling support for setting automatic/manual fan control\n");
+	}
+
 	if (!fan_mult) {
 		/*
 		 * Autodetect fan multiplier based on nominal rpm

drivers/hwmon/ltc2947-i2c.c

+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Analog Devices LTC2947 high precision power and energy monitor over I2C
+ *
+ * Copyright 2019 Analog Devices Inc.
+ */
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/regmap.h>
+
+#include "ltc2947.h"
+
+static const struct regmap_config ltc2947_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8,
+};
+
+static int ltc2947_probe(struct i2c_client *i2c,
+			 const struct i2c_device_id *id)
+{
+	struct regmap *map;
+
+	map = devm_regmap_init_i2c(i2c, &ltc2947_regmap_config);
+	if (IS_ERR(map))
+		return PTR_ERR(map);
+
+	return ltc2947_core_probe(map, i2c->name);
+}
+
+static const struct i2c_device_id ltc2947_id[] = {
+	{"ltc2947", 0},
+	{}
+};
+MODULE_DEVICE_TABLE(i2c, ltc2947_id);
+
+static struct i2c_driver ltc2947_driver = {
+	.driver = {
+		.name = "ltc2947",
+		.of_match_table = ltc2947_of_match,
+		.pm = &ltc2947_pm_ops,
+	},
+	.probe = ltc2947_probe,
+	.id_table = ltc2947_id,
+};
+module_i2c_driver(ltc2947_driver);
+
+MODULE_AUTHOR("Nuno Sa <nuno.sa@analog.com>");
+MODULE_DESCRIPTION("LTC2947 I2C power and energy monitor driver");
+MODULE_LICENSE("GPL");

drivers/hwmon/ltc2947-spi.c

+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Analog Devices LTC2947 high precision power and energy monitor over SPI
+ *
+ * Copyright 2019 Analog Devices Inc.
+ */
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/regmap.h>
+#include <linux/spi/spi.h>
+
+#include "ltc2947.h"
+
+static const struct regmap_config ltc2947_regmap_config = {
+	.reg_bits = 16,
+	.val_bits = 8,
+	.read_flag_mask = BIT(0),
+};
+
+static int ltc2947_probe(struct spi_device *spi)
+{
+	struct regmap *map;
+
+	map = devm_regmap_init_spi(spi, &ltc2947_regmap_config);
+	if (IS_ERR(map))
+		return PTR_ERR(map);
+
+	return ltc2947_core_probe(map, spi_get_device_id(spi)->name);
+}
+
+static const struct spi_device_id ltc2947_id[] = {
+	{"ltc2947", 0},
+	{}
+};
+MODULE_DEVICE_TABLE(spi, ltc2947_id);
+
+static struct spi_driver ltc2947_driver = {
+	.driver = {
+		.name = "ltc2947",
+		.of_match_table = ltc2947_of_match,
+		.pm = &ltc2947_pm_ops,
+	},
+	.probe = ltc2947_probe,
+	.id_table = ltc2947_id,
+};
+module_spi_driver(ltc2947_driver);
+
+MODULE_AUTHOR("Nuno Sa <nuno.sa@analog.com>");
+MODULE_DESCRIPTION("LTC2947 SPI power and energy monitor driver");
+MODULE_LICENSE("GPL");

drivers/hwmon/ltc2947.h

+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef _LINUX_LTC2947_H
+#define _LINUX_LTC2947_H
+
+struct regmap;
+
+extern const struct of_device_id ltc2947_of_match[];
+extern const struct dev_pm_ops ltc2947_pm_ops;
+
+int ltc2947_core_probe(struct regmap *map, const char *name);
+
+#endif

drivers/hwmon/pmbus/Kconfig

@@ -36,6 +36,15 @@ config SENSORS_ADM1275
 	  This driver can also be built as a module. If so, the module will
 	  be called adm1275.
 
+config SENSORS_BEL_PFE
+	tristate "Bel PFE Compatible Power Supplies"
+	help
+	  If you say yes here you get hardware monitoring support for BEL
+	  PFE1100 and PFE3000 Power Supplies.
+
+	  This driver can also be built as a module. If so, the module will
+	  be called bel-pfe.
+
 config SENSORS_IBM_CFFPS
 	tristate "IBM Common Form Factor Power Supply"
 	depends on LEDS_CLASS

drivers/hwmon/pmbus/Makefile

@@ -6,6 +6,7 @@
 obj-$(CONFIG_PMBUS)		+= pmbus_core.o
 obj-$(CONFIG_SENSORS_PMBUS)	+= pmbus.o
 obj-$(CONFIG_SENSORS_ADM1275)	+= adm1275.o
+obj-$(CONFIG_SENSORS_BEL_PFE)	+= bel-pfe.o
 obj-$(CONFIG_SENSORS_IBM_CFFPS)	+= ibm-cffps.o
 obj-$(CONFIG_SENSORS_INSPUR_IPSPS) += inspur-ipsps.o
 obj-$(CONFIG_SENSORS_IR35221)	+= ir35221.o

drivers/hwmon/pmbus/bel-pfe.c

+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Hardware monitoring driver for BEL PFE family power supplies.
+ *
+ * Copyright (c) 2019 Facebook Inc.
+ */
+
+#include <linux/err.h>
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pmbus.h>
+
+#include "pmbus.h"
+
+enum chips {pfe1100, pfe3000};
+
+/*
+ * Disable status check for pfe3000 devices, because some devices report
+ * communication error (invalid command) for VOUT_MODE command (0x20)
+ * although correct VOUT_MODE (0x16) is returned: it leads to incorrect
+ * exponent in linear mode.
+ */
+static struct pmbus_platform_data pfe3000_plat_data = {
+	.flags = PMBUS_SKIP_STATUS_CHECK,
+};
+
+static struct pmbus_driver_info pfe_driver_info[] = {
+	[pfe1100] = {
+		.pages = 1,
+		.format[PSC_VOLTAGE_IN] = linear,
+		.format[PSC_VOLTAGE_OUT] = linear,
+		.format[PSC_CURRENT_IN] = linear,
+		.format[PSC_CURRENT_OUT] = linear,
+		.format[PSC_POWER] = linear,
+		.format[PSC_TEMPERATURE] = linear,
+		.format[PSC_FAN] = linear,
+
+		.func[0] = PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT |
+			   PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT |
+			   PMBUS_HAVE_POUT |
+			   PMBUS_HAVE_VIN | PMBUS_HAVE_IIN |
+			   PMBUS_HAVE_PIN | PMBUS_HAVE_STATUS_INPUT |
+			   PMBUS_HAVE_TEMP | PMBUS_HAVE_TEMP2 |
+			   PMBUS_HAVE_STATUS_TEMP |
+			   PMBUS_HAVE_FAN12,
+	},
+
+	[pfe3000] = {
+		.pages = 7,
+		.format[PSC_VOLTAGE_IN] = linear,
+		.format[PSC_VOLTAGE_OUT] = linear,
+		.format[PSC_CURRENT_IN] = linear,
+		.format[PSC_CURRENT_OUT] = linear,
+		.format[PSC_POWER] = linear,
+		.format[PSC_TEMPERATURE] = linear,
+		.format[PSC_FAN] = linear,
+
+		/* Page 0: V1. */
+		.func[0] = PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT |
+			   PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT |
+			   PMBUS_HAVE_POUT | PMBUS_HAVE_FAN12 |
+			   PMBUS_HAVE_VIN | PMBUS_HAVE_IIN |
+			   PMBUS_HAVE_PIN | PMBUS_HAVE_STATUS_INPUT |
+			   PMBUS_HAVE_TEMP | PMBUS_HAVE_TEMP2 |
+			   PMBUS_HAVE_TEMP3 | PMBUS_HAVE_STATUS_TEMP |
+			   PMBUS_HAVE_VCAP,
+
+		/* Page 1: Vsb. */
+		.func[1] = PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT |
+			   PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT |
+			   PMBUS_HAVE_PIN | PMBUS_HAVE_STATUS_INPUT |
+			   PMBUS_HAVE_POUT,
+
+		/*
+		 * Page 2: V1 Ishare.
+		 * Page 3: Reserved.
+		 * Page 4: V1 Cathode.
+		 * Page 5: Vsb Cathode.
+		 * Page 6: V1 Sense.
+		 */
+		.func[2] = PMBUS_HAVE_VOUT,
+		.func[4] = PMBUS_HAVE_VOUT,
+		.func[5] = PMBUS_HAVE_VOUT,
+		.func[6] = PMBUS_HAVE_VOUT,
+	},
+};
+
+static int pfe_pmbus_probe(struct i2c_client *client,
+			   const struct i2c_device_id *id)
+{
+	int model;
+
+	model = (int)id->driver_data;
+
+	/*
+	 * PFE3000-12-069RA devices may not stay in page 0 during device
+	 * probe which leads to probe failure (read status word failed).
+	 * So let's set the device to page 0 at the beginning.
+	 */
+	if (model == pfe3000) {
+		client->dev.platform_data = &pfe3000_plat_data;
+		i2c_smbus_write_byte_data(client, PMBUS_PAGE, 0);
+	}
+
+	return pmbus_do_probe(client, id, &pfe_driver_info[model]);
+}
+
+static const struct i2c_device_id pfe_device_id[] = {
+	{"pfe1100", pfe1100},
+	{"pfe3000", pfe3000},
+	{}
+};
+
+MODULE_DEVICE_TABLE(i2c, pfe_device_id);
+
+static struct i2c_driver pfe_pmbus_driver = {
+	.driver = {
+		   .name = "bel-pfe",
+	},
+	.probe = pfe_pmbus_probe,
+	.remove = pmbus_do_remove,
+	.id_table = pfe_device_id,
+};
+
+module_i2c_driver(pfe_pmbus_driver);
+
+MODULE_AUTHOR("Tao Ren <rentao.bupt@gmail.com>");
+MODULE_DESCRIPTION("PMBus driver for BEL PFE Family Power Supplies");
+MODULE_LICENSE("GPL");

drivers/hwmon/pmbus/ibm-cffps.c

@@ -3,6 +3,7 @@
  * Copyright 2017 IBM Corp.
  */
 
+#include <linux/bitfield.h>
 #include <linux/bitops.h>
 #include <linux/debugfs.h>
 #include <linux/device.h>
@@ -29,6 +30,10 @@
 #define CFFPS_INPUT_HISTORY_CMD			0xD6
 #define CFFPS_INPUT_HISTORY_SIZE		100
 
+#define CFFPS_CCIN_VERSION			GENMASK(15, 8)
+#define CFFPS_CCIN_VERSION_1			 0x2b
+#define CFFPS_CCIN_VERSION_2			 0x2e
+
 /* STATUS_MFR_SPECIFIC bits */
 #define CFFPS_MFR_FAN_FAULT			BIT(0)
 #define CFFPS_MFR_THERMAL_FAULT			BIT(1)
@@ -39,9 +44,13 @@
 #define CFFPS_MFR_VAUX_FAULT			BIT(6)
 #define CFFPS_MFR_CURRENT_SHARE_WARNING		BIT(7)
 
+/*
+ * LED off state actually relinquishes LED control to PSU firmware, so it can
+ * turn on the LED for faults.
+ */
+#define CFFPS_LED_OFF				0
 #define CFFPS_LED_BLINK				BIT(0)
 #define CFFPS_LED_ON				BIT(1)
-#define CFFPS_LED_OFF				BIT(2)
 #define CFFPS_BLINK_RATE_MS			250
 
 enum {
@@ -54,7 +63,7 @@ enum {
 	CFFPS_DEBUGFS_NUM_ENTRIES
 };
 
-enum versions { cffps1, cffps2 };
+enum versions { cffps1, cffps2, cffps_unknown };
 
 struct ibm_cffps_input_history {
 	struct mutex update_lock;
@@ -292,28 +301,38 @@ static int ibm_cffps_read_word_data(struct i2c_client *client, int page,
 	return rc;
 }
 
-static void ibm_cffps_led_brightness_set(struct led_classdev *led_cdev,
+static int ibm_cffps_led_brightness_set(struct led_classdev *led_cdev,
 					enum led_brightness brightness)
 {
 	int rc;
+	u8 next_led_state;
 	struct ibm_cffps *psu = container_of(led_cdev, struct ibm_cffps, led);
 
 	if (brightness == LED_OFF) {
-		psu->led_state = CFFPS_LED_OFF;
+		next_led_state = CFFPS_LED_OFF;
 	} else {
 		brightness = LED_FULL;
+
 		if (psu->led_state != CFFPS_LED_BLINK)
-			psu->led_state = CFFPS_LED_ON;
+			next_led_state = CFFPS_LED_ON;
+		else
+			next_led_state = CFFPS_LED_BLINK;
 	}
 
+	dev_dbg(&psu->client->dev, "LED brightness set: %d. Command: %d.\n",
+		brightness, next_led_state);
+
 	pmbus_set_page(psu->client, 0);
 
 	rc = i2c_smbus_write_byte_data(psu->client, CFFPS_SYS_CONFIG_CMD,
-				       psu->led_state);
+				       next_led_state);
 	if (rc < 0)
-		return;
+		return rc;
 
+	psu->led_state = next_led_state;
 	led_cdev->brightness = brightness;
+
+	return 0;
 }
 
 static int ibm_cffps_led_blink_set(struct led_classdev *led_cdev,
@@ -323,10 +342,7 @@ static int ibm_cffps_led_blink_set(struct led_classdev *led_cdev,
 	int rc;
 	struct ibm_cffps *psu = container_of(led_cdev, struct ibm_cffps, led);
 
-	psu->led_state = CFFPS_LED_BLINK;
-
-	if (led_cdev->brightness == LED_OFF)
-		return 0;
+	dev_dbg(&psu->client->dev, "LED blink set.\n");
 
 	pmbus_set_page(psu->client, 0);
 
@@ -335,6 +351,8 @@ static int ibm_cffps_led_blink_set(struct led_classdev *led_cdev,
 	if (rc < 0)
 		return rc;
 
+	psu->led_state = CFFPS_LED_BLINK;
+	led_cdev->brightness = LED_FULL;
 	*delay_on = CFFPS_BLINK_RATE_MS;
 	*delay_off = CFFPS_BLINK_RATE_MS;
 
@@ -351,7 +369,7 @@ static void ibm_cffps_create_led_class(struct ibm_cffps *psu)
 		 client->addr);
 	psu->led.name = psu->led_name;
 	psu->led.max_brightness = LED_FULL;
-	psu->led.brightness_set = ibm_cffps_led_brightness_set;
+	psu->led.brightness_set_blocking = ibm_cffps_led_brightness_set;
 	psu->led.blink_set = ibm_cffps_led_blink_set;
 
 	rc = devm_led_classdev_register(dev, &psu->led);
@@ -395,7 +413,7 @@ static int ibm_cffps_probe(struct i2c_client *client,
 			   const struct i2c_device_id *id)
 {
 	int i, rc;
-	enum versions vs;
+	enum versions vs = cffps_unknown;
 	struct dentry *debugfs;
 	struct dentry *ibm_cffps_dir;
 	struct ibm_cffps *psu;
@@ -405,8 +423,27 @@ static int ibm_cffps_probe(struct i2c_client *client,
 		vs = (enum versions)md;
 	else if (id)
 		vs = (enum versions)id->driver_data;
-	else
+
+	if (vs == cffps_unknown) {
+		u16 ccin_version = CFFPS_CCIN_VERSION_1;
+		int ccin = i2c_smbus_read_word_swapped(client, CFFPS_CCIN_CMD);
+
+		if (ccin > 0)
+			ccin_version = FIELD_GET(CFFPS_CCIN_VERSION, ccin);
+
+		switch (ccin_version) {
+		default:
+		case CFFPS_CCIN_VERSION_1:
 			vs = cffps1;
+			break;
+		case CFFPS_CCIN_VERSION_2:
+			vs = cffps2;
+			break;
+		}
+
+		/* Set the client name to include the version number. */
+		snprintf(client->name, I2C_NAME_SIZE, "cffps%d", vs + 1);
+	}
 
 	client->dev.platform_data = &ibm_cffps_pdata;
 	rc = pmbus_do_probe(client, id, &ibm_cffps_info[vs]);
@@ -465,6 +502,7 @@ static int ibm_cffps_probe(struct i2c_client *client,
 static const struct i2c_device_id ibm_cffps_id[] = {
 	{ "ibm_cffps1", cffps1 },
 	{ "ibm_cffps2", cffps2 },
+	{ "ibm_cffps", cffps_unknown },
 	{}
 };
 MODULE_DEVICE_TABLE(i2c, ibm_cffps_id);
@@ -478,6 +516,10 @@ static const struct of_device_id ibm_cffps_of_match[] = {
 		.compatible = "ibm,cffps2",
 		.data = (void *)cffps2
 	},
+	{
+		.compatible = "ibm,cffps",
+		.data = (void *)cffps_unknown
+	},
 	{}
 };
 MODULE_DEVICE_TABLE(of, ibm_cffps_of_match);

drivers/hwmon/tmp421.c

@@ -127,7 +127,8 @@ static struct tmp421_data *tmp421_update_device(struct device *dev)
 
 	mutex_lock(&data->update_lock);
 
-	if (time_after(jiffies, data->last_updated + 2 * HZ) || !data->valid) {
+	if (time_after(jiffies, data->last_updated + (HZ / 2)) ||
+	    !data->valid) {
 		data->config = i2c_smbus_read_byte_data(client,
 			TMP421_CONFIG_REG_1);
 

drivers/hwmon/w83793.c

@@ -2096,7 +2096,7 @@ static struct w83793_data *w83793_update_device(struct device *dev)
 static u8 w83793_read_value(struct i2c_client *client, u16 reg)
 {
 	struct w83793_data *data = i2c_get_clientdata(client);
-	u8 res = 0xff;
+	u8 res;
 	u8 new_bank = reg >> 8;
 
 	new_bank |= data->bank & 0xfc;