arm64: dts: sc7180: Factor out ti-sn65dsi86 support

Factor out ti-sn65dsi86 edp bridge as a separate dts fragment.
This helps us introduce the second source edp bridge later.
Signed-off-by: Philip Chen <philipchen@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211008113839.v3.1.Ibada67e75d2982157e64164f1d11715d46cdc42c@changeid

arch/arm64/boot/dts/qcom/sc7180-trogdor-coachz.dtsi

@@ -11,6 +11,7 @@
 ap_h1_spi: &spi0 {};
 
 #include "sc7180-trogdor.dtsi"
+#include "sc7180-trogdor-ti-sn65dsi86.dtsi"
 
 /* Deleted nodes from trogdor.dtsi */
 

arch/arm64/boot/dts/qcom/sc7180-trogdor-homestar.dtsi

@@ -11,6 +11,7 @@
 ap_h1_spi: &spi0 {};
 
 #include "sc7180-trogdor.dtsi"
+#include "sc7180-trogdor-ti-sn65dsi86.dtsi"
 
 / {
 	/* BOARD-SPECIFIC TOP LEVEL NODES */

arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor.dtsi

@@ -11,6 +11,7 @@
 ap_h1_spi: &spi0 {};
 
 #include "sc7180-trogdor.dtsi"
+#include "sc7180-trogdor-ti-sn65dsi86.dtsi"
 
 &ap_sar_sensor {
 	semtech,cs0-ground;

arch/arm64/boot/dts/qcom/sc7180-trogdor-pompom.dtsi

@@ -11,6 +11,7 @@
 ap_h1_spi: &spi0 {};
 
 #include "sc7180-trogdor.dtsi"
+#include "sc7180-trogdor-ti-sn65dsi86.dtsi"
 
 / {
 	thermal-zones {

arch/arm64/boot/dts/qcom/sc7180-trogdor-r1.dts

@@ -13,6 +13,7 @@
 ap_h1_spi: &spi0 {};
 
 #include "sc7180-trogdor.dtsi"
+#include "sc7180-trogdor-ti-sn65dsi86.dtsi"
 
 / {
 	model = "Google Trogdor (rev1+)";

arch/arm64/boot/dts/qcom/sc7180-trogdor-ti-sn65dsi86.dtsi

+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Trogdor dts fragment for the boards with TI sn65dsi86 edp bridge
+ *
+ * Copyright 2021 Google LLC.
+ */
+
+&dsi0_out {
+	remote-endpoint = <&sn65dsi86_in>;
+	data-lanes = <0 1 2 3>;
+};
+
+edp_brij_i2c: &i2c2 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	sn65dsi86_bridge: bridge@2d {
+		compatible = "ti,sn65dsi86";
+		reg = <0x2d>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&edp_brij_en>, <&edp_brij_irq>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <11 IRQ_TYPE_LEVEL_HIGH>;
+
+		enable-gpios = <&tlmm 104 GPIO_ACTIVE_HIGH>;
+
+		vpll-supply = <&pp1800_edp_vpll>;
+		vccio-supply = <&pp1800_brij_vccio>;
+		vcca-supply = <&pp1200_brij>;
+		vcc-supply = <&pp1200_brij>;
+
+		clocks = <&rpmhcc RPMH_LN_BB_CLK3>;
+		clock-names = "refclk";
+
+		no-hpd;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				sn65dsi86_in: endpoint {
+					remote-endpoint = <&dsi0_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+				sn65dsi86_out: endpoint {
+					data-lanes = <0 1>;
+					remote-endpoint = <&panel_in_edp>;
+				};
+			};
+		};
+
+		aux-bus {
+			panel: panel {
+				/* Compatible will be filled in per-board */
+				power-supply = <&pp3300_dx_edp>;
+				backlight = <&backlight>;
+				hpd-gpios = <&sn65dsi86_bridge 2 GPIO_ACTIVE_HIGH>;
+
+				port {
+					panel_in_edp: endpoint {
+						remote-endpoint = <&sn65dsi86_out>;
+					};
+				};
+			};
+		};
+	};
+};
+
+&tlmm {
+	edp_brij_irq: edp-brij-irq {
+		pinmux {
+			pins = "gpio11";
+			function = "gpio";
+		};
+
+		pinconf {
+			pins = "gpio11";
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+	};
+};

arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi

@@ -602,15 +602,6 @@ &camcc {
 &dsi0 {
 	status = "okay";
 	vdda-supply = <&vdda_mipi_dsi0_1p2>;
-
-	ports {
-		port@1 {
-			endpoint {
-				remote-endpoint = <&sn65dsi86_in>;
-				data-lanes = <0 1 2 3>;
-			};
-		};
-	};
 };
 
 &dsi_phy {
@@ -618,70 +609,6 @@ &dsi_phy {
 	vdds-supply = <&vdda_mipi_dsi0_pll>;
 };
 
-edp_brij_i2c: &i2c2 {
-	status = "okay";
-	clock-frequency = <400000>;
-
-	sn65dsi86_bridge: bridge@2d {
-		compatible = "ti,sn65dsi86";
-		reg = <0x2d>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&edp_brij_en>, <&edp_brij_irq>;
-		gpio-controller;
-		#gpio-cells = <2>;
-
-		interrupt-parent = <&tlmm>;
-		interrupts = <11 IRQ_TYPE_LEVEL_HIGH>;
-
-		enable-gpios = <&tlmm 104 GPIO_ACTIVE_HIGH>;
-
-		vpll-supply = <&pp1800_edp_vpll>;
-		vccio-supply = <&pp1800_brij_vccio>;
-		vcca-supply = <&pp1200_brij>;
-		vcc-supply = <&pp1200_brij>;
-
-		clocks = <&rpmhcc RPMH_LN_BB_CLK3>;
-		clock-names = "refclk";
-
-		no-hpd;
-
-		ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			port@0 {
-				reg = <0>;
-				sn65dsi86_in: endpoint {
-					remote-endpoint = <&dsi0_out>;
-				};
-			};
-
-			port@1 {
-				reg = <1>;
-				sn65dsi86_out: endpoint {
-					data-lanes = <0 1>;
-					remote-endpoint = <&panel_in_edp>;
-				};
-			};
-		};
-
-		aux-bus {
-			panel: panel {
-				/* Compatible will be filled in per-board */
-				power-supply = <&pp3300_dx_edp>;
-				backlight = <&backlight>;
-				hpd-gpios = <&sn65dsi86_bridge 2 GPIO_ACTIVE_HIGH>;
-
-				port {
-					panel_in_edp: endpoint {
-						remote-endpoint = <&sn65dsi86_out>;
-					};
-				};
-			};
-		};
-	};
-};
-
 ap_sar_sensor_i2c: &i2c5 {
 	clock-frequency = <400000>;
 
@@ -1234,19 +1161,6 @@ pinconf {
 		};
 	};
 
-	edp_brij_irq: edp-brij-irq {
-		pinmux {
-			pins = "gpio11";
-			function = "gpio";
-		};
-
-		pinconf {
-			pins = "gpio11";
-			drive-strength = <2>;
-			bias-pull-down;
-		};
-	};
-
 	en_pp3300_codec: en-pp3300-codec {
 		pinmux {
 			pins = "gpio83";